Documente Academic
Documente Profesional
Documente Cultură
CLIPLINE
Application Note
2615B
F1
F2
F3
L1 L2 L3
F4
OFF
1 2 3
4 5 6
7 8 9
0
ON
F1
F2
F3
F4
1 2 3
4 5 6
7 8 9
0
Simple, 3-phase
transducer test set
5 6
Open
Closed
s1 s2
1 2
Open
Closed
Input
Output
L1 L2 L3
OFF
Output
s1 s2
s1 s2
Input
s1 s2
CAUTION
The SB-ME switching bridge must be installed
in the bridging channel on the CT (or input) side
of the terminal block.
UTME Application
ON
F1
F2
F3
L1 L2 L3
F4
OFF
1 2 3
4 5 6
7 8 9
0
ON
OFF
Output
5 6 7
Open
Closed
F1
F2
F3
L1 L2 L3
F4
1 2 3
4 5 6
7 8 9
0
1 2 3 4 5 6
A
B
(Open) (Closed)
s1 s2 s1 s2 s1 s2
s1 s2 PE
Input
Input
Output
s1 s2 PE
s1 s2 s1 s2 s1 s2
The third configuration uses two ME knife-disconnect terminal blocks and one SB-ME 2-8 switching bridge (Figure 4).
CT leads are connected to the input side of the ME series
terminal block, and the transducer/measurement device is
connected to the output side.
ON
F1
F2
F3
L1 L2 L3
F4
OFF
1 2 3
4 5 6
7 8 9
0
Output
5 6 7
Open
Closed
Closed
(shunt up)
Input
s1 s2 PE
s1 s2 PE
Open
(shunt down)
PHOENIX CONTACT
2615B
UTME Application
2. Secure the shorting bar by tightening the screws. The
CT is now neutralized and the circuit is safe to open.
a. For circuits that include an ME knife-disconnect
terminal block, the knife disconnects can now be
safely opened.
b. For circuits using MED feed-through terminal blocks,
the wire(s) can now be disconnected.
3. The test signal can now be injected into the transducer/
meter side of the circuit by inserting the signal probes
into the test adapters or connecting the signal to the
disconnected wiring of the measurement circuit.
To return the unit to normal operation, perform the above
steps in reverse order:
1. Disconnect the test signal/probes from the transducer
wires or remove probes from the test plugs.
a. For circuits that include the ME, the knife disconnect
must now be CLOSED.
b. For circuits that include the MED feed-through terminal blocks, the wiring must now be reconnected.
4. Tighten the screws to prevent movement and inadvertent shorting of the CT.
The CT measurement circuit is now functional.
ON
F1
F2
F3
L1 L2 L3
F4
OFF
1 2 3
4 5 6
7 8 9
0
Linked 3-phase
transducer test set
Output
A
(Open)
1 2 3 4 5 6
s1 s2 s1 s2 s1 s2
Input
B
(Closed)
s1 s2 s1 s2 s1 s2
PHOENIX CONTACT
2615B
UTME Application
2
3
Figure 8. Components
Description
Type
Order No.
Pcs./Pkt.
UTME 6
3047400
UTMED 6
3047413
UTMED 6-PE
3047442
PHOENIX CONTACT
2615B
UTME Application
Table 2 Accessories
Item
2615B
Description
Type Code
Part No.
PAI-4-FIX BU
PAI-4-FIX RD
PAI-4-FIX YE
PAI-4-FIX GN
PAI-4-FIX VT
PAI-4-FIX BK
PAI-4-FIX BN
PAI-4-FIX GY
PAI-4-FIX OG
3032729
3032732
3032745
3032758
3032761
3032774
3032787
3032790
3034455
ZB 8
1052002
Connecting bridge
C-ME 6/2
3034442
Switch lock
S-ME 6
3034439
FBS 2-8
FBS 3-8
FBS 4-8
FBS 5-8
FBS 6-8
FBS 10-8
3030284
3030297
3030307
3030310
3032470
3030323
SB-ME 2-8
SB-ME 4-8
3034468
3034484
End bracket
E/NS 35 N
0800886
D-UTME 6
3047426
PHOENIX CONTACT GmbH & Co KG 32823 Blomberg Germany Phone: +49-(0) 5235-3-00
PHOENIX CONTACT P.O. Box 4100 Harrisburg, PA 17111-0100 USA Phone: +1-717-944-1300
www.phoenixcontact.com