Documente Academic
Documente Profesional
Documente Cultură
GODOWN
Bill No
Description
10
11
12
13
14
15
16
Amount
IBM GODOWN
Item
Description
BILL No: 01 - PRELIMINARIES
Unit
Qty
Rate
Amount
item
1.00
No
1.00
item
1.00
1.5 CLEAN-UP
(1) Allow for clean-up upon completion of the works.
item
1.00
3/10/2011
Page 1of 14
IBM GODOWN
Item
Description
BILL No: 02 - GROUND WORKS
Unit
Qty
Rate
Amount
2.1 GENERAL
(a) Rates shall include for: leveling, grading, trimming,
compacting to faces of excavation, keep sides plumb, backfilling,
consolidating and disposing surplus soil.
2.2 DEMOLISION
(a) Removing of Exsisting Single storey building (Nearly 5m
high) and removing of all the demolished material away from the
site.
item
1.00
529.09
2.4 EXCAVATION
Excavation quantities are measured to the faces of concrete
members. Rates shall include for all additional excavation
required to place the formwork.
2.4.1 Excavation for foundations
(1) Foundation raft and Plinth beams
42.73
2.5 FILLING
Rates shall include for: leveling, grading, trimming, compacting
and similar.
(1) Compacted earth filling under ground screed
(2) 10mm thick blinding
m
m
104.16
529.09
529.09
3/10/2011
Page 2of 14
IBM GODOWN
Item
Description
BILL No: 03 - CONCRETE
Unit
Qty
Rate
Amount
3.1 GENERAL
(a) Rates shall include for: placing in position; making good
after removal of formwork, mortar touch up to all concrete and
casting in all required items; additional concrete required to
conform to structural and excavated tolerances.
(b) Mix ratio for reinforced concrete shall be 1:2:3 and lean
concrete shall be 1:2:6
(1) Allow for concrete testing
3.2 LEAN CONCRETE
(a) Quantity is measured to the edges of concrete foundation
members. Rates shall be inclusive for any additional concrete
required to place the formwork.
50mm thick lean concrete to foundations
(1) Under footings & Plinth beams (50mm thk)
item
1.00
2.96
m
m
m
m
m
m
m
5.58
2.65
1.20
0.19
0.48
7.83
3.34
79.36
3/10/2011
Page 3of 14
IBM GODOWN
Item
Description
BILL No: 04 - MASONRY AND PLASTERING
Unit
Qty
Rate
Amount
4.1 GENERAL
(a) Rates shall include for: cleaning out cavities, forming rebated
reveals and pointing and cleaning down to reveals where
necessary; fractional size blocks, all necessary machine cutting,
cutting or forming chases or edges of
floor slabs, cutting or leaving holes and openings as recesses for
and building in pipes, conduits, sleeves and similar as required
for all trades; leaving surfaces rough or raking out joints for
plastering and flashings, bedding
frames or plates, building in joists, bearers or similar, temporary
supports to openings, templates, reinforcement in walls and for
all necessary making good.
4.2 BRICKWORK
4.2.1 150mm thick masonry solid block wall, bricks laid to form
alternate courses of headers and stretchers, laid on and incl.
mortar
4.2.1.1 Ground Floor
251.95
4.3 PLASTERING
4.3.1 16 mm thick cement plaster on internal surface as specified on
the drawing. (internal surfaces)
4.3.1.1 Ground floor
170.25
355.77
4.66
3/10/2011
Page 4of 14
IBM GODOWN
Item
Description
BILL No: 05 - STRUCTURAL STEEL WORK
Unit
Qty
Rate
Amount
5.1 GENERAL
(a) Rates shall include for: all fabrication work, welding,
marking, drilling, for bolts including those securing timbers, steel
plates, bolts, nuts and any type of washer, riveted work, counter
sinking and tapping for bolts or machine screws.
(b) Rates shall include for all painting and finished as
specified.
(c)Rates shall include for fabrication and erection and temporary
supports and fixing in to position.
(d)Rate shall include for forming openings for the doors and
windows where every necessary and finishing the opening edges
smoothly using flashings as required.
5.2 STEEL COLUMNS
5.2.1 (a) I section columns bolted to the foundation using and 20mm
thk (270x450mm) grade 350 base plate with 4mm fillet weld all
around column and 4 nos of 24 mm anchor bolts as per details
given
(b) I section Columns jointed with 2 nos of 20mm thk
530x270mm plates with 8 nos of M20 G8.8 bolts and base plate
welded to I section with 8mm filet weld all around the column.
Joint to be made each C1 column)
(c) column tops fixed 20mm thk plate to required roof angle
(Plate welded 8mm fillet welding all around to column)
5.2.2
5.2.2.1
5.2.2.2
5.2.2.3
nos
nos
nos
10.00
10.00
5.00
First Floor
Beam B01 (171x352 Section 3871mm long)
Beam B01 (171x352 Section 5074mm long)
Beam B01 (171x352 Section 6018mm long)
Beam B01 (171x352 Section 5727mm long)
Beam B01 (171x352 Section 4968mm long)
Beam B01 (171x352 Section 5993mm long)
Beam B01 (171x352 Section 5723mm long)
Beam B01 (171x352 Section 5458mm long)
nos
nos
nos
nos
nos
nos
nos
nos
5.00
5.00
5.00
5.00
4.00
2.00
2.00
2.00
nos
2.00
Roof level
Beam B02 (165x304 Section 4968mm long)
Beam B02 (165x304 Section 5993mm long)
Beam B02 (165x304 Section 5723mm long)
Beam B02 (165x304 Section 5458mm long)
nos
nos
nos
nos
2.00
2.00
2.00
2.00
5.3.1.1
5.3.1.2
5.3.1.3
5.3.1.4
5.3.1.5
5.3.1.6
5.3.1.7
5.3.1.8
5.3.1.10
5.3.1.11
5.3.1.12
5.3.1.13
3/10/2011
Page 5of 14
IBM GODOWN
Item
Description
Unit
5.3.3 (a) 144mm dia 4.5mm CHS strut fixed to 120x120x10mm thk
cap plate 4mm fillet weld all around and 10mm thk cleats welded
perpendicular to cap plate.
(b) 10 mm cleat fixed to column and with 4mm filet weld all
around and strut fixed to cleat with 2 nos of M20 bolts.
First Floor
nos
5.3.4.1 4968mm long
nos
5.3.4.2 5993mm long
nos
5.3.4.3 5723mm long
nos
5.3.4.4 5458mm long
Roof level
nos
5.3.4.5 4968mm long
nos
5.3.4.6 5993mm long
nos
5.3.4.7 5723mm long
nos
5.3.4.8 5458mm long
Qty
Rate
Amount
1.00
3.00
3.00
3.00
1.00
1.00
3.00
1.00
nos
5.00
m
no
900.00
380.00
m
no
950.00
420.00
no
no
4.00
4.00
no
no
4.00
4.00
no
m
10.00
30.00
3/10/2011
Page 6of 14
IBM GODOWN
Item
Description
BILL No: 06- METALWORK
Unit
Qty
Rate
Amount
6.1 GENERAL
(a) Rates shall include for: all fabrication work, welding,
marking, drilling, for bolts including those securing timbers, steel
plates, bolts, nuts and any type of washer, riveted work, counter
sinking and tapping for bolts or machine screws.
(b) Rates shall include for all painting and finished as
specified.
(c)Rates shall include for fabrication and erection and temporary
supports and fixing in to position.
(d)Rate shall include for forming openings for the doors and
windows where every necessary and finishing the opening edges
smoothly using flashings as required.
6.2 WALL CLADING FRAME
6.2.1 Horizontal C purlings
(a) 50x100 C purling with a 5mm thk 40mmx40mm , 75mm
long L angle brackets and a 5mm thk 40mmx75mm long plate on
each joint fixed with 8 nos of M12 G8.8 Bolts on each joint (rate
for joint shall include only exceeding 6 m )
(b) Horizontal spacing to be 1000mm
6.2.1.1 Ground floor C purlings 1295 mm long
6.2.1.2 Ground floor C purlings 6270 mm long
6.2.1.3 Ground floor C purlings 6138 mm long
6.2.1.4 Ground floor C purlings 6007 mm long
6.2.1.5 Ground floor C purlings 1385 mm long
6.2.1.6 Ground floor C purlings 6248 mm long
6.2.1.7 Ground floor C purlings 6363 mm long
6.2.1.8 Ground floor C purlings 5431 mm long
6.2.1.9 Ground floor C purlings 4466 mm long
6.2.1.10 Ground floor C purlings 1134 mm long
6.2.1.11 Ground floor C purlings 5013 mm long
6.2.1.12 Ground floor C purlings 5980 mm long
6.2.1.13 Ground floor C purlings 5013 mm long
6.2.1.14 Ground floor C purlings 5944 mm long
6.2.1.15 Ground floor C purlings 5280 mm long
nos
nos
nos
nos
nos
nos
nos
nos
nos
nos
nos
nos
nos
nos
nos
4.00
4.00
3.00
3.00
2.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
6.2.1.16
6.2.1.17
6.2.1.18
6.2.1.19
6.2.1.20
6.2.1.21
6.2.1.22
6.2.1.23
6.2.1.24
nos
nos
nos
nos
nos
nos
nos
nos
nos
10.00
7.00
7.00
10.00
7.00
5.00
6.00
6.00
5.00
1.00
3/10/2011
Page 7of 14
IBM GODOWN
Item
Description
BILL No: 07 - CLADDING WORK
Unit
Qty
Rate
Amount
7.1 GENERAL
7.1.1 Rates shall include for: fair edges, dressing over angel fillets,
turning into grooves, all other labours, circular edges, nails,
screws and other fixings and laps.
7.2 WALL CLADDING
7.2.1 lysaght cladding panel to manufactures specifications and fixes
to C purling frame with self driven screws as required and Ribs
horizontally
7.2.2 Sheet rib laps should be kept for manufactures specifications and
horizontal laps to be keep minimum of 200mm laps
7.2.3 Necessary corner flashing to be fixed on corners as per
manufactures specifications
(1) Ground to roof level
409.74
m
m
556.05
556.05
8.3 CAPPING
(1) Lysaght ridge Flashing as per drawing
(2) Lysaght end Flashing as per drawing
m
m
22.39
49.58
8.4 GUTTER
(1) BHP lysaght gutter
44.78
item
1.00
5.00
8.1 GENERAL
8.1.1 Rates shall include for: fair edges, dressing over angel fillets,
turning into grooves, all other labours, circular edges, nails,
screws and other fixings and laps.
8.2 ROOF COVERING
8.2.2 BHP Lysaght Trimdek Hi-Ten or equivalent roofing sheet, over
C purlin frame including all fixings, fixed in accordance with
manufacturer's instructions.
8.2.3 50mm rockwool insulation with foil backing on one side.
3/10/2011
Page 8of 14
IBM GODOWN
Item
Description
BILL No: 09 - WOODWORK
Unit
Qty
Rate
Amount
9.1 GENERAL
(a) Rates shall include for: all labour in framing, notching and
fitting around projections, pipes, light fittings, hatches, grilles
and similar and complete with cleats, packers, wedges and
similar and all nails and screws.
9.2 TIMBER VALANCE BOARD
25X250 Timber plank and Flat ZnAl sheet (to cover the balance
of truss-270mm high) fixed to the roof truss
44.78
518.23
4.66
10.1 GENERAL
(a) Rates shall include for locks, latches, closers, push plates,
pull handles, bolts, kick plates, hinges and all door & window
hardware.
(b) Rates shall include for door frames, mullions, transoms,
trims, glazing, tinting, timber panels, boarding, framing, lining,
fastenings and all fixings.
(c) Sizes are given overall outside dimensions of actual doors
and windows.
(d) Thickness and sizes of glass panels are shown on the
Drawings and doors and windows schedule
(e) Rates shall include for all painting as specified
(f) Rates shall include all items specified in the door schedule
and specification
(g.) Frames and sashes to be 25-60 micron White powder
coated Aluminium other wise specified.
10.2
10.2.1
(1)
(2)
(3)
(4)
(5)
(6)
(7)
nos
nos
nos
nos
nos
nos
nos
1.00
1.00
1.00
2.00
2.00
1.00
1.00
10.2.2
(1)
(2)
(3)
(4)
FIRST FLOOR
D1 (1700x2150) Al framed and louvers swing door
W02 (5730x1775) Alluminium Door with Glass opening
W02a (4946x1775) Alluminium Door with Glass opening
W02b (4705x1775) Alluminium Door with Glass opening
nos
nos
nos
nos
1.00
1.00
1.00
1.00
10.3 OTHERS
Sun portal day light system (fixed as per manufacture's
specifications)
nos
8.00
3/10/2011
Page 9of 14
IBM GODOWN
Item
Description
BILL No: 11 - PAINTING
Unit
Qty
Rate
Amount
11.1 GENERAL
(a) Rates shall include for: the provision, erection and removal
of scaffolding, preparation, wall putty application, rubbing down
between coats and similar work, the protection and/or masking
floors, fittings and similar work, removing and
replacing door and window furniture
(b) All painting work shall be carried in accordance with the
Specifications
11.2 WALL PAINTING
11.2.1 Textured paint finish/matte emulsion paint finish as specified in
specification. (external surfaces)
(1) Ground Floor
170.25
355.77
2.30
8.93
(toilet)
(1) Ground floor
3/10/2011
Page 10of 14
IBM GODOWN
Item
Description
Unit
BILL No: 13 - HYDRAULICS AND DRAINAGE
13.1 HYDRAULICS
13.1.1 General
(a) Rates shall include for: sockets, running joints, connectors,
elbows, junctions, valves, reducers, expansion joints; backnuts
and similar; incidental fittings, clips, saddles, brackets, straps,
hangers, screws, nails and
fixing complete, including cutting and forming holes; excavating,
laying pipes and backfilling trenches
(b) All pipework and fittings shall be UPVC
Qty
item
item
1.00
1.00
no
no
no
no
no
no
2.00
2.00
2.00
2.00
1.00
3.00
item
item
1.00
1.00
13.2.5 manholes
600mm dia,600mm deep RCC Inspection chamber with RCC
cover slab sealed type
nos
1.00
13.1.5
(1)
(2)
(3)
(4)
(5)
(6)
Rate
Amount
13.2 DRAINAGE
13.2.1 General
(a) Rates shall include for: excavation, maintaining faces of drain
pipe trenches and pits, backfilling, disposal of surplus spoil;
bends, junctions, reducers, expansion joints and all joints and
other incidental materials.
(b) All pipework shall be uPVC
3/10/2011
Page 11of 14
IBM GODOWN
Item
Description
Unit
BILL NO: 14 - ELECTRICAL INSTALLATIONS
14.1 GENERAL
(a) Design, provide and install electrical network for the entire
building complete in accordance to standards set by the local
governing body STELCO
(b) The following items and description and the drawings HULS
-01 to HULS-05 are given as a guidance as to the nature of the
information required to be returned by the
contractor. Should they not be appropriate the contractor should
provide a similar BoQ using the Add/Omit sheets provided at the
back of this BoQ
(c) The cost shall include for: screws, nails, bolts, nuts, standard
cable fixing or supporting clips, brackets, straps, rivets, plugs and
all incidental accessories
(d) The cost shall also include for trenching including:
excavation, maintaining faces of excavations, backfilling,
compaction, appropriate cable covers, warning tape and disposal
of surplus spoil
(e) Rates for electrical isolators, conduits, fittings, equipment
and similar items shall include for: all fixings to various building
surfaces
(f) A light fixture is measured as one point; switch end of wire is
not included in the quantity.
(g) A point wiring for power points is measured (regardless of 1
gang, 2 gang etc) as one point for each socket outlet; other end of
wire is not included in the quantity.
(h) Contractor shall provide all cabling, wiring, conduits, etc.
within the site boundaries. Cabling, wiring, conduits etc. outside
the site boundaries are not included under this Contract.
Qty
no
no
1.00
1.00
no
no
no
2.00
2.00
1.00
points
points
39.00
14.00
no
no
no
no
2.00
28.00
3.00
6.00
14.7 SWITCHES
(1) Light switch
no
34.00
14.8 SOCKETS
(1) 13 A SSO
(2) 13 A twin SSO
no
no
7.00
7.00
LIGHTING
Ceiling light
22" Aluminium Low bay light (40W)
4 ft Fluorescent industrial light
Emergency Lights
Rate
Amount
3/10/2011
Page 12of 14
IBM GODOWN
Item
Description
BILL NO: 15- LIFT & HOISTS WORKS
Unit
Qty
Rate
Amount
15.1 LIFTS
15.1.1 GENERAL
(a) Rates shall include for: screws, nails, bolts, nuts, standard
cable fixing or supporting clips, brackets, straps, rivets, plugs and
all incidental accessories
(b) Rates for work in trench shall include for: excavation,
maintaining faces of excavations, backfilling, compaction,
appropriate cable covers, warning tape and disposal of surplus
spoil
(c) Rates for cable conduits, fittings, equipment and similar
items shall include for: all fixings to various building surfaces
(d) Rates shall include for all necessary electrical wiring and
accessories required for completion of the lift installation
(e) MWSC will supply the Scissor type Elevator.
(e) Rate shall include shifting the Elevator from Hulhumale and
complete installation.
15.1.2 Scissor Type Freight Elevator from autoquip or similar to
specifications (rate shall include all supporting frame works and
any additional items required)
nos
1.00
3/10/2011
Page 13of 14
IBM GODOWN
Item
16.1
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
(9)
(10)
(11)
(12)
(13)
(14)
(16)
Description
Unit
Qty
Rate
Amount
ADDITIONS
Bill 01- Preliminaries
Bill 02- Ground works
Bill 03- Concrete works
Bill 04- Masonry works
Bill 05- Structural steel work
Bill 06- Metal works
Bill 07- Cladding works
Bill 08- Roofing
Bill 09- Wood work
Bill 10- Door window
Bill 11- Painting
Bill 12- Finishes
Bill 13- Hydraulics and Drainages
Bill 14- Electrical installation
Bill 15- Lift & Hoists work
TOTAL
16.2
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
(9)
(10)
(11)
(12)
(13)
(14)
(16)
OMISSIONS
Bill 01- Preliminaries
Bill 02- Ground works
Bill 03- Concrete works
Bill 04- Masonry works
Bill 05- Structural steel work
Bill 06- Metal works
Bill 07- Cladding works
Bill 08- Roofing
Bill 09- Wood work
Bill 10- Door window
Bill 11- Painting
Bill 12- Finishes
Bill 13- Hydraulics and Drainages
Bill 14- Electrical installation
Bill 15- Lift & Hoists work
TOTAL
3/10/2011
Page 14of 14