Documente Academic
Documente Profesional
Documente Cultură
45M623N5UK-01
GENERAL
All technical information contained in this manual has been developed and compiled with great care and has been
reproduced taking advantage of advanced controlling mechanisms. The manufacturer reserves the right to make
changes to this manual at any time.
AUSTRIAN GAMING INDUSTRIES GmbH gives no guarantee and accepts no legal responsibility (neither as a
liability nor in any other way) for any errors and consequences that may arise from incorrect statements or
incorrect use.
The author welcomes any notifications of errors or ambiguities. The product names used in this manual may be
registered trademarks and / or brands of the relevant companies belonging to the Novomatic Group.
All rights reserved.
Any form of reproduction (printing, photocopying or other means) of any part of this manual, and any processing,
multiplying and distributing by the use of electronic systems shall be prohibited unless
AUSTRIAN GAMING INDUSTRIES GmbH has given written consent.
This manual is part of the device and must be passed on together with the device to any new owner or holder
of the device. It must be kept for the whole useful life of the device and must be accessible to technical staff
at all times.
This manual was created in accordance with the European norm EN 62079:2001 and is valid for
HOT SPOT PLATINUM (FV-623) Kernel 5.7
until a newer manual version is released. The version number of the User Manual is indicated as the
identification number on the inner page margin.
For identification of the device refer to the ID plate attached on either side of the device.
The plate also contains the required official approval symbol (CE, CSA).
Illustr. 0.1
ID Plate
E-Mail: support@novomatic.com
07 2008 AGI GmbH
45M623N5UK-01
GENERAL
45M623N5UK-01
This manual is divided into five sections. Each chapter explains a specific area of how to use the machine.
In the enclosure you find the table of illustrations and the glossary.
Part I
Introduction
Part II
Installation
Part III
Troubleshooting
Part IV
Part V
Hardware
Annex
table of illustrations
glossary
Page 3
GENERAL
Part I
I.1
I.2
I.3
Introduction
Operating elements
Description of components
Machine dimensions
7
9
10
11
Part II
II.1
II.2
II.3
II.4
Installation
Inspection (damages caused by transport)
Installation instructions
Power up
Safety precautions
13
15
15
16
17
Part III
III.1
III.2
Troubleshooting
Lack of line voltage supply
Error messages of the software
21
23
24
Part IV
25
IV.1
IV.2
IV.3
IV.4
IV.5
IV.6
IV.7
IV.8
IV.9
Part V
V.1
V.2
V.3
V.4
V.5
V.6
V.7
V.8
V.9
V.10
V.11
V.12
V.13
Error handling
Remote in
Handpay credit
Hopper refill
Hopper dump
Out of Service (Locking of the machine)
Top light
Audit Menu
RAM Clear
27
49
51
53
55
57
59
61
109
Hardware
Power supply
Bill acceptor
Coin acceptor
Hopper
Monitors
COOLFIRE Motherboard
COOLFIRE Backplane
Top light
Illumination
Mechanical meters
Door optics/switches
Loudspeakers
Preventative maintenance
111
115
119
127
135
139
145
151
165
169
177
181
185
189
Annex
Table of Illustrations
Glossary
Page 4
45M623N5UK-01
Table of Contents
195
197
199
GENERAL
Legend
45M623N5UK-01
DANGER
ATTENTION
INFORMATION
NOTE
TROUBLESHOOTING
Page 5
GENERAL
Technical Data
Type
Dimensions in mm (l x h x d)
Weight
ca. 101 kg
Power supply
230 V / 50 Hz / 1,6 A
resp. 110 V / 60 Hz
Power
250 W
Fuses
T 3 A 15 (230 V)
T 5 A (12 V)
Thermal danger
Certain parts become hot during
operation and cause injuries!
Electrical danger
Whenever the machine is open,
voltaged parts can be touched!
Power down the machine whenever
you do repair or maintenance work!
Mechanical danger
Note that some flanges within the
device are sharp-edged and cause
injuries!
Improper opening and closing of the
device can lead to contusion!
Favourable operating temperature in C
10 - 35
Humidity in %
30% - 80%
(non-condensing)
Page 6
45M623N5UK-01
Manufacturer
Austrian Gaming Industries
Wiener Strasse 158
A-2352 Gumpoldskirchen
Austria
Part I Introduction
I.1
Operating elements
I.2
Description of components
I.3
Machine dimensions
45M623N5UK-01
45M623N5UK-01
INTRODUCTION
Page 8
INTRODUCTION
3
4
5
45M623N5UK-01
6
7
623FV_Ansichten.eps
1 Attendant keyswitch
2 Coin slot
3 Bill insertion
4 Main door lock
5 Main door lever
6 Door in door lever
7 Door in door lock
Page 9
INTRODUCTION
8
1
10
12
14
16
11
13
45M623N5UK-01
15
17
18
19
FV623_Komponenten.eps
P a g e
10
11 Bill acceptor
12 COOLFIRE Backplane
13 Stacker door with lock
14 Hopper
15 Door optics (receiver)
16 Ticket printer (optional)
17 Switching power supply (behind stacker)
18 Main switch
19 Drop door with lock
07 2008 AGI GmbH
INTRODUCTION
2086
600
1938
45M623N5UK-01
1231
107
420
540
Z_FV623CF_Abmessungen.eps
P a g e
11
45M623N5UK-01
INTRODUCTION
P a g e
12
45M623N5UK-01
Part II
Installation
II.1
II.2
Installation instructions
II.3
Power up
II.4
Safety precautions
45M623N5UK-01
INSTALLATION
P a g e
14
INSTALLATION
It must be ensured that the machine is operated in an upright position. Further, the machine has to be
screwed down tightly to the base by means of the mounting material included in the delivery.
The minimum distance between two machines should be 21 cm to avoid possible damage when opening
the main door. The minimum distance to a possible back wall or the like should be 10 cm.
The drilling jig (see illustr. II.2.1) has to be used in case the machine is to be installed on a table provided
by the customer (i.e. if the machine has been delivered without base).
361.5
76.7
143.2
261.2
464.2
540
353.2
37.7
15(4x)
8(8x)
430
378.5
285.5
270.5
255.5
140.5
45M623N5UK-01
62
65.5
Z_CS_Bohrschablone.eps
NOTE
The width of the drilling jig corresponds to that of the respective cabinet (540 cm),
the depth does not correspond, because this jig is used for various cabinet types!
Take the back cabinet edge as reference edge (i.e. the back edge of the drilling jig corresponds
to the back cabinet edge).
See the drilling scheme (Illustr. II.2.2) for the necessary drillings of the respective machine type.
P a g e
15
INSTALLATION
See the ID plate (see illustr. 0.1) for the machine (cabinet) type.
For pilot drilling use two twist drills ( 10 mm and 5 mm).
After the required drillings have been made by means of the drilling jig, continue with
redrilling using a cylinder saw 60 mm.
45M623N5UK-01
Z_CS_Bohrplan.eps
II.3 Power up
1) Before start check the line voltage. The machine has been designed to sustain 230 V 10%, 50 Hz
or 110 V 10%, 60 Hz. Make sure that the line voltage is corresponds to the voltage indicated on
the machine.
2) As all machines of the HOT SPOT PLATINUM Series are equipped with an earthing connection,
it should be ensured that the main supply is also equipped with an earthing connection.
3) Plug in the main plug correctly.
4) Open the main door.
5) If the machine is equipped with a coin comparitor, place the reference coin in there.
6) Refill the hopper.
7) Switch on the machine.
8) Close the main door.
9) After a short self test the machine is ready for operation.
10) Credits can be added and a new game can be started.
P a g e
16
INSTALLATION
For operating safety and to avoid damage to the machine, read carefully and observe
the following instructions.
Because the attendee responsible for usual maintenance has to open the machine, he has to
get informed about the safety precautions.
There are static-sensitive parts inside the machine which could be damaged by electric discharge.
Ground yourself by touching a ground strap inside the machine to neutralize electric charges
before changing or maintaining inner parts.
DANGER
45M623N5UK-01
Only disconnect the power line from the outlet achieves a powerless machine!
For machine with uninterruptible power supply (UPS) you have to switch it off, too!
Unplugging the machine with wet hands can result in
a risk of electric shock!
If there are unusual smells or sounds coming from the machine, unplug the unit from the AC outlet
immediately and for machines with an UPS power it off, too.
Contact a qualified service personnel.
Continued operation may be dangerous and can result in a risk of fire or electric shock.
Never spill liquid of any kind (coffee, wine, etc.) on the machine.
In case of an accident, this may result in a risk of fire or electric shock.
Unplug the unit and have it checked by qualified service personnel.
P a g e
17
INSTALLATION
Do not lead anything onto the power cord and do not bruise or stretch any wires.
Damaged wires can result in a risk of fire or short circuit.
Keep the wires away from where people will walk on them or stumble and be injured.
ATTENTION
Environment
Opening on top, sides and in the bottom of the cabinet are provided for ventilation.
To ensure proper operation and to prevent overheating, these openings should not be blocked
or covered.
To allow hot air to escape make sure that there is a minimum space of 10 cm between the machine
and a wall or alike.
If the machine becomes too hot, it might cause a fire hazard.
P a g e
18
45M623N5UK-01
INSTALLATION
MISCELLANEOUS
Do not install machines with CRT monitors close to strong magnetic fields like loudspeakers
or fluorescent lamps.
Those equipments could bias the monitor, unusual noises could be heard.
Do not hit or scratch the surface. High pressure of sharp objects could cause irreparable damages.
To clean the surface use some absorbent cotton or soft cloth and a window cleaner.
If the display accidentally breaks and the liquid crystal material leaks, it should be kept away from
the eyes or mouth.
In case of contact with hands, legs or clothes, it must be washed away thoroughly with soap.
45M623N5UK-01
NOTE
If you follow these instructions closely and the machine is maintained and handled in a proper way,
it complies with the usual safety standards.
The manufacturer warns explicitly against predictable, unconventional use of the machine as well as
predictable malpractice. Do not bypass the built-in safety precautions in the machine!
Arbitrary alterations and changes of the machine are prohibited for safety reasons.
For security reasons any changes and exchanges of defective parts have to be accomplished with
originally or manufacturer-registered parts.
The manufacturer calls attention to the fact that spare parts that were not delivered by the
Austrian Gaming Industries are neither tested or approved by AGI.
The installation and/or use of such parts might negatively affect the machines performance.
The manufacturer cannot be held responsible for errors that result from such parts.
P a g e
19
INSTALLATION
The following service instructions are for use by qualified or trained personnel only.
The owner of the machine has to assure that only qualified or trained personnel perform services.
To avoid personal injury or damage to the equipment, do not perform any servicing other than
such contained in this manual.
45M623N5UK-01
ATTENTION
P a g e
20
Troubleshooting
III.1
III.2
45M623N5UK-01
Part III
45M623N5UK-01
TROUBLESHOOTING
P a g e
22
TROUBLESHOOTING
ATTENTION
Each power up is followed by a short self test. Then the machine is ready for operation.
If this is not the case, check the machine for the following possible error sources.
The power supply is primary secured at 230 V with two T3A15 inert single-pole fuses.
The primary fuses are located on the front of the main switch module (illustr. III.1.1).
More details regarding (a) defective line voltage(s) can only be given by measurements
with suitable devices.
If the error cannot be cleared, please see part V - Power supply for further information.
45M623N5UK-01
fuses T3A15
main switch
Z_Schaltermodul_lang.jpg
ATTENTION
P a g e
23
TROUBLESHOOTING
After the machine has been powered up, the major parts of the machine (e.g. hopper, CPU board etc.)
are subject to a self test.
If this test has been successful, the machine switches automatically to the ready-for-play status.
The error management engages each malfunction and/or manipulation is detected.
If the machine detects an error, the corresponding code is shown on the screen (see illustr. III.2.1).
S_Fehleranzeige_UK.eps
P a g e
24
45M623N5UK-01
If an error cannot be cleared this way, see part IV - Game and Software.
45M623N5UK-01
Part IV
IV.1
Error handling
IV.2
Remote in
IV.3
Handpay credit
IV.4
Hopper refill
IV.5
Hopper dump
IV.6
IV.7
Top light
IV.8
Audit Menu
IV.9
RAM Clear
45M623N5UK-01
P a g e
26
45M623N5UK-01
attendant keyswitch
Z_FV623CF_Seitenansicht.eps
If an error occurs, the machine will interrupt the current game and switch automatically to failure mode.
1) An acoustic signal can be heard.
2) The blue light of the top light is flashing slowly respectively the red light is on.
3) The error message together with a short description is shown in the middle of the screen.
Below the procedure how to clear the error is explained (see illustr. IV.1.3).
Page 27
If more errors occur, activate the attendant keyswitch until all errors have been cleared.
If an error cannot be cleared this way, follow the instructions of the error code table.
S_FehlerCF2_E_99_9_UK.jpg
Note the error and inform our technical support (+43 2252 606-300) about it.
Other errors
Error code
Error name
Error handling
S_FehlerCF2_E_2101_UK.jpg
P a g e
28
45M623N5UK-01
INFORMATION
ATTENTION
ATTENTION
If any hardware components like stacker box, hopper or coin acceptor are missing, no start-up
of the machine is possible.
Before the start-up screen is displayed, an error message appears on the screen.
Quitting this error can force restart of the machine but new appearing of this error message
(depends on software version and missing components).
TROUBLESHOOTING
45M623N5UK-01
Switch off the machine and replace the missing hardware component.
Now after restarting the machine the error can be cleared by turning the attendant keyswitch.
P a g e
29
P a g e
30
45M623N5UK-01
4
4
4
4
4
4
4
P a g e
31
45M623N5UK-01
P a g e
32
45M623N5UK-01
P a g e
33
Handling:
Turn/release the attendant key.
If the error cannot be cleared, check the cashless connection.
Handling:
Turn/release the attendant key.
If the error cannot be cleared, check the connectors and the cables of the door log.
If the error cannot be cleared, the door log has to be exchanged.
Handling:
Turn/release the attendant key.
If the error cannot be cleared, the ROM (door log program) has to be exchanged.
DL 3 - RAM battery low
Handling:
Turn/release the attendant key.
If the error cannot be cleared, the RAM battery has to be exchanged.
If the machine has been switched off, it may loose data or receive wrong data.
45M623N5UK-01
Handling:
Perform a RAM Clear (
see part IV.9 - RAM Clear).
If the error cannot be cleared, the game selector has to be exchanged.
Handling:
Turn/release the attendant key.
Check the game selector. If the error cannot be cleared, ensure that the game selector is
properly seated.
Handling:
Perform a RAM Clear (
see part IV.9 - RAM Clear).
If the error cannot be cleared, the game selector has to be exchanged.
Handling:
Turn/release the attendant key.
Check the game selector. If the error cannot be cleared, the game selector has to be exchanged.
P a g e
34
Handling:
Turn/release the attendant key.
If the error cannot be cleared, the game selector has to be exchanged.
Handling:
Turn/release the attendant key.
Check the game selector. If the error cannot be cleared, the game selector has to be exchanged.
Handling:
Turn/release the attendant key.
Check the game selector. If the error cannot be cleared, the game selector has to be exchanged.
Handling:
45M623N5UK-01
Handling:
Turn/release the attendant key.
Check the game selector. If the error cannot be cleared, the game selector has to be exchanged.
Handling:
Turn/release the attendant key.
If the error cannot be cleared, the connectors of the jackpot controller have to be checked.
Handling:
Turn/release the attendant key.
If the error cannot be cleared, the connectors of the jackpot controller have to be checked.
E0
Handling:
Occurs after a RAM Clear. The basic settings must be made
(
see MACHINE > INITIAL SETUP).
Handling:
Occurs after a RAM Clear. The basic settings must be made (
P a g e
35
E2
Handling:
Switch off/on the machine.
If the error cannot be cleared, the Coolfire mainboard has to be exchanged.
Handling:
Turn/release the attendant key.
E7 1 - Meters disconnected
Handling:
Connect the meters.
Turn/release the attendant key.
If the error cannot be cleared, open the Main Door and power down the machine.
Check the connectors of the meters Pay attention to any signs of manipulation attempts.
Power up the machine and close the Main Door.
If the error cannot be cleared, the meters have to be exchanged.
Handling:
Turn/release the attendant key.
If the error cannot be cleared, check the connectors and cables of the display.
If the error cannot be cleared, the display has to be exchanged.
45M623N5UK-01
Handling:
The Coolfire mainboard has to be exchanged.
Handling:
Turn/release the attendant key.
If the error cannot be cleared, check the connectors and cables of the display.
If the error cannot be cleared, the display has to be exchanged.
Handling:
Open the Main Door and turn the attendant key.
Check the reel module systematically, release the attendant key and close the Main Door.
4 2
P a g e
36
Handling:
Open the Main Door and turn the attendant key.
Check whether the reel has worked itself loose from the axis or if the sensor on the
PCB reel light barrier (P366) is dirty. Release the attendant key and close the Main Door.
If the error cannot be cleared, the defective reel has to be exchanged.
4 3
4 4
45M623N5UK-01
4 6
4 8
4 9
Handling:
Open the Main Door and turn the attendant key.
Release the attendant key and close the Main Door.
If the error cannot be cleared, the reel may be damaged, has loosened from the motor axis
or is touching it.
Handling:
Open the Main Door and turn the attendant key.
Check if the sensors are dirty or defective. Release the attendant key and close the Main Door.
If the error cannot be cleared, the defective reel has to be exchanged.
Handling:
Open the Main Door and turn the attendant key.
Check if the sensors are dirty or defective. Release the attendant key and close the Main Door.
If the error cannot be cleared, the defective reel has to be exchanged.
Handling:
Open the Main Door and turn the attendant key.
Check whether the reel has worked itself loose from the axis or if the sensor on the
PCB reel light barrier (P366) is dirty. Release the attendant key and close the Main Door.
If the error cannot be cleared, the defective reel has to be exchanged.
Handling:
Open the Main Door and turn the attendant key.
Release the attendant key and close the Main Door.
If the error cannot be cleared, the respective reel module and/or the LED/lamp controller board
has to be exchanged.
Handling:
Turn/release the attendant key.
Handling:
Open the Main Door and turn the attendant key.
Perform a RAM Clear (
see part IV.9 - RAM Clear).
If the error cannot be cleared, the reel software has to be exchanged.
The reel software is placed on the reel interface.
Handling:
P a g e
37
Handling:
Open the Main Door and turn the attendant key.
Exchange the reel software on the reel interface. If the error cannot be cleared,
the reel software has to be exchanged. Release the attendant key and close the Main Door.
Handling:
Open the Main Door and turn the attendant key.
Release the attendant key and close the Main Door.
If the error cannot be cleared, the respective reel module and/or the LED/lamp controller board
have to be exchanged.
7 09 -
7 10 -
Handling:
Turn/release the attendant key.
If the error cannot be cleared, the interface ROM of the lightwheel or the lightwheel board
needs to be exchanged.
45M623N5UK-01
Handling:
Turn/release the attendant key.
If the error cannot be cleared, check the connectors and cables of the lightwheel and/or
change the lightwheel interface.
P a g e
38
Handling:
Turn/release the attendant key.
The RAM battery has to be exchanged as soon as possible.
If the machine has been switched off it may loose data or receive wrong data.
Handling:
Power down/up the machine.
If the error cannot be cleared, the mainboard has to be exchanged.
If the machine has been switched off it may loose data or receive wrong data.
Handling:
Turn the attendant key and check the time set. If necessary, adjust it.
The RAM battery may be empty.
If the error cannot be cleared, the mainboard has to be exchanged.
Handling:
Turn/release the attendant key.
If the error cannot be cleared, check the network cables.
45M623N5UK-01
Handling:
Turn/release the attendant key.
If the error cannot be cleared, the mainboard has to be exchanged.
Handling:
Turn the attendant key and open the Main Door.
Set current date and time in the real-time clock
(
see part IV.8 - AUDIT MENU > CALIBRATION > CLOCK SETUP).
Close the Main Door and release the attendant key.
21 0 - Diverter error
Handling:
Turn/release the attendant key.
If the error cannot be cleared, open the Main Door and power down the machine.
Check the coin diverter and the coin channels for jammed coins. Also check the connecting plugs
and the cables of the magnet. Power up the machine and close the Main Door. Perform the
coin diverter test (
see part IV.8 - AUDIT MENU > DIAGNOSTIC > COIN DIVERTER TEST).
If the error cannot be cleared, the coin diverter or the coin acceptor should be exchanged.
Also, the sensors may be defective, or may need to be re-adjusted.
P a g e
39
21 2 - Coin in jam
Handling:
Turn/release the attendant key.
If the error cannot be cleared, open the Main Door and power down the machine.
Check the coin acceptor for any signs of manipulation attempts. Check the connectors and the
cables of the coin acceptor systematically. Power up the machine and close the Main Door.
If the error cannot be cleared, the coin acceptor has to be exchanged
(
see part V - Coin acceptor).
Handling:
Turn/release the attendant key.
If the error cannot be cleared, open the Main Door and power down the machine.
The light barrier of the coin channel was blocked too long or a coin is stuck. Remove coins stuck
and check the connectors and cables of the light barrier.
Power up the machine and close the Main Door.
Handling:
Turn/release the attendant key.
If the error cannot be cleared, open the Main Door and power down the machine.
Check the coin acceptor and the coin channel optics for dirt or damage.
Furthermore, check the connectors and the cables of the coin optics and the coin acceptor.
The three light barriers have to be placed in the centre of the borings, the optical line between
transmitter and receiver must not be blocked. Power up the machine and close the Main Door.
If the error cannot be cleared, the coin acceptor or the light barriers have to be exchanged
(
see part V - Coin acceptor).
Handling:
Turn/release the attendant key.
If the error cannot be cleared, open the Main Door and power down the machine.
Check the connectors and the cables of the coin acceptor systematically. Power up the machine
and close the Main Door. If the error cannot be cleared, the coin acceptor has to be exchanged
(
see part V - Coin acceptor).
P a g e
40
Handling:
Turn/release the attendant key.
If the error cannot be cleared, open the Main Door and power down the machine.
Check the coin acceptor for any signs of manipulation attempts. Furthermore, please check if a
reference coin is placed in the coin comparitor. Check the connectors and the cables of the coin
acceptor systematically. Power up the machine and close the Main Door.
If the error cannot be cleared, the coin acceptor or the coin diverter has to be exchanged
(
see part V - Coin acceptor).
Also, the sensors may be defective or may need to be re-adjusted.
45M623N5UK-01
Handling:
Turn/release the attendant key.
If the error cannot be cleared, open the Main Door and power down the machine.
Check the connectors and cables of the top coin optics.
Power up the machine and close the Main Door.
If the error cannot be cleared, the top coin optics have to be exchanged.
Handling:
Turn/release the attendant key.
If the error cannot be cleared, open the Main Door and power down the machine.
Check the connectors and cables of the bottom coin optics.
Power up the machine and close the Main Door.
If the error cannot be cleared, the bottom coin optics have to be exchanged.
Handling:
Turn/release the attendant key. The bill will be rejected.
45M623N5UK-01
Handling:
Turn/release the attendant key.
The bill is registered and transported into the stacker.
Handling:
Turn/release the attendant key.
If the error cannot be cleared, open the Main Door and power down the machine.
Try to remove the stuck bill. Power up the machine and close the Main Door.
If the error cannot be cleared, the bill acceptor may be disabled to continue the operation of the
game without bill acceptor. To do so, deactivate all bill acceptor channels in the
MACHINE SETUP > BILLS/COINS SETTINGS. Consequently, the bill acceptor has to be
exchanged (
see part V - Bill acceptor).
P a g e
41
27 3 - Jam in stacker
Handling:
Turn/release the attendant key.
If the error cannot be cleared, open the Main Door and power down the machine.
Try to remove the stuck bill. Power up the machine and close the Main Door.
If the error cannot be cleared, the bill acceptor may be disabled to continue the operation of the
game without bill acceptor. To do so, deactivate all bill acceptor channels in the
MACHINE SETUP > BILLS/COINS SETTINGS. Consequently, the bill acceptor has to be
exchanged (
see part V - Bill acceptor).
ATTENTION
The stacker may contain a large amount of bills and the error clearing should be
carried out in a secure area.
Handling:
Turn/release the attendant key.
If the error cannot be cleared, open the Main Door and power down the machine.
Check the connectors and the cables of the bill acceptor. Make sure, that the bill acceptor has
been put in place properly. Power up the machine and close the Main Door.
If the error cannot be cleared, the bill acceptor may be disabled to continue the operation of the
game without bill acceptor. To do so, deactivate all bill acceptor channels in the
MACHINE SETUP > BILLS/COINS SETTINGS. Consequently, the bill acceptor has to be
exchanged (
see part V - Bill acceptor).
27 5 - No stacker box
P a g e
42
Handling:
Turn/release the attendant key.
If the error cannot be cleared, open the Main Door and power down the machine.
Check if the stacker box is fixed correctly in its mounting. Furthermore, check the connectors
and the cables of the bill acceptor. Power up the machine and close the Main Door.
If the error cannot be cleared, the bill acceptor may be disabled to continue the operation of the
game without bill acceptor. To do so, deactivate all bill acceptor channels in the
MACHINE SETUP > BILLS/COINS SETTINGS. Consequently, the bill acceptor has to be
exchanged (
see part V - Bill acceptor).
45M623N5UK-01
45M623N5UK-01
Handling:
The stacker is full.
Open the Stacker Door and take out the stacker.
Remove the bills, put the stacker in its mounting and close the Stacker Door.
Turn/release the attendant key.
Handling:
Turn/release the attendant key.
If the error cannot be cleared, open the Main Door and power down the machine.
Check if the cables of the bill acceptor and the stacker are connected properly.
Power up the machine and close the Main Door.
If the error cannot be cleared, the bill acceptor may be disabled to continue the operation of the
game without bill acceptor. To do so, deactivate all bill acceptor channels in the
MACHINE SETUP > BILLS/COINS SETTINGS. Consequently, the bill acceptor has to be
exchanged (
see part V - Bill acceptor).
27 8 - Stacker full
Handling:
Turn/release the attendant key.
If the error cannot be cleared, open the Main Door and power down the machine.
Check if the bill acceptor is dirty or damaged and if the connectors and cables are put in place
properly. If necessary, clean the bill acceptor. Check the bill acceptor for any manipulation.
Power up the machine and close the Main Door.
If the error cannot be cleared, the bill acceptor may be disabled to continue the operation of the
game without bill acceptor. To do so, deactivate all bill acceptor channels in the
MACHINE SETUP > BILLS/COINS SETTINGS. Consequently, the bill acceptor has to be
exchanged (
see part V - Bill acceptor).
Handling:
Turn/release the attendant key.
If the error cannot be cleared, open the Main Door.
Check if a coin or dirt is stuck in the light barrier of the hopper ad remove it if necessary.
Close the Main Door. If the error cannot be cleared, the hopper has to be exchanged.
33 00 - Hopper empty
Handling:
Refill the hopper.
Turn the attendant key (to get directly to the Menu Hopper refill), then release the key again.
P a g e
43
33 0 - Printer is disconnected
Handling:
Turn/release the attendant key.
If the error cannot be cleared, open the Main Door and power down the machine.
Check the connectors and cables of the printer. Make sure, that the printer has been put in place
properly. Power up the machine and close the Main Door.
If the error cannot be cleared, the printer may be disabled in the machine setup to continue the
operation of the game without printer (MACHINE SETUP > PRINTER SETTINGS).
Consequently, the printer has to be exchanged (
see part V - Ticket Printer).
Handling:
The printer is deactivated.
To use the printer activate it in the MACHINE SETUP > PRINTER SETTINGS.
33 3 - No ticket
Handling:
Turn/release the attendant key.
Check the fill level of the printer. The tickets from the box should be put in the printer properly.
33 4 - Paper jam
Handling:
Turn/release the attendant key.
If the error cannot be cleared, open the Main Door and power down the machine.
Try to remove the stuck paper in the printer. Power up the machine and close the Main Door.
If the error cannot be cleared, the printer may be disabled in the machine setup to continue the
operation of the game without printer (MACHINE SETUP > PRINTER SETTINGS).
Consequently, the printer has to be exchanged (
see part V - Ticket Printer).
Handling:
Turn/release the attendant key.
If the error cannot be cleared, open the Main Door and power down the machine.
Check the connectors and the cables of the printer. Make sure that the printer has been put in
place properly. The tickets from the box should be put in the printer properly.
Power up the machine and close the Main Door.
If the error cannot be cleared, the printer may be disabled in the machine setup to continue the
operation of the game without printer (MACHINE SETUP > PRINTER SETTINGS).
Consequently, the printer has to be exchanged (
see part V - Ticket Printer).
34 0 - Hopper disconnected
P a g e
44
Handling:
Turn/release the attendant key.
If the error cannot be cleared, open the Main Door.
Check if the hopper is installed and if both light diodes are illuminated. If the light diodes of the
hopper are not illuminated, check if the hopper is pushed all the way in. Check systematically the
connectors and the cables of the hopper. Power up the machine and close the Main Door.
If the error cannot be cleared, the hopper has to be exchanged (
see part V - Hopper).
07 2008 AGI GmbH
45M623N5UK-01
34 1 - Hopper tilt
34 2 - Hopper low
Handling:
Turn/release the attendant key.
If the error cannot be cleared, open the Main Door and power down the machine.
Check if a coin or dirt is stuck in the light barrier of the hopper and remove it if necessary.
Power up the machine and close the Main Door.
If the error cannot be cleared, the hopper has to be exchanged (
see part V - Hopper).
Handling:
Turn/release the attendant key.
Check the fill level of the hopper. The contact plates on the bottom of the hopper should be
covered with coins. The hopper should be refilled as soon as possible. Check whether the hopper
low level is activated in the software (MACHINE SETUP > HOPPER SETTINGS).
Handling:
Indicated on the screen with a special window and registered in the machine log file.
Perform a handpay.
45M623N5UK-01
Handling:
Indicated on the screen with a special window and registered in the machine log file.
Perform a handpay.
Handling:
Indicated on the screen with a special window and registered in the machine log file.
Perform a handpay.
Handling:
Indicated on the screen with a special window and registered in the machine log file.
Perform a handpay.
35 3 - Jackpot won
Handling:
Indicated on the screen with a special window and registered in the machine log file.
Perform a handpay.
Handling:
Indicated on the screen with a special window and registered in the machine log file.
Perform a handpay.
P a g e
45
Handling:
Indicated on the screen with a special window and registered in the machine log file.
Perform a handpay.
35 7 - Noncash win
Handling:
The won credit is higher than the cashable credit. Perform a handpay.
61
- RAM error
Handling:
Perform a RAM Clear (
see part IV.9 - RAM Clear).
Accounting data can be viewed, but they may be wrong.
If the error cannot be cleared, the mainboard has to be exchanged.
Handling:
Perform a RAM Clear (
see part IV.9 - RAM Clear).
If the error cannot be cleared, the ROM (game program) has to be exchanged.
45M623N5UK-01
Handling:
Turn/release the attendant key.
63 1 - Logic area open
Handling:
Close the logic area. Turn/release the attendant key.
Handling:
Close the Drop Door.
Turn/release the attendant key.
If the error cannot be cleared, check if the Drop Door is fixed correctly in its mounting.
In addition, check the connectors and the cables of the door switch.
Handling:
Close the Stacker Door
Turn/release the attendant key.
If the error cannot be cleared, check if the Stacker Door is fixed correctly in its mounting.
In addition, check the connectors and the cables of the micro switch.
P a g e
46
Handling:
Turn/release the attendant key.
If the error cannot be cleared, the defective door sensor has to be exchanged
(
see part V - Door optics/switches).
07 2008 AGI GmbH
65 0 - Bad EEPROM
Handling:
Turn/release the attendant key.
If the error cannot be cleared, the EEPROM has to be exchanged.
Handling:
Turn/release the attendant key.
If the error cannot be cleared, the EEPROM has to be exchanged.
Handling:
Perform a RAM Clear (
see part IV.9 - RAM Clear).
If the error cannot be cleared, the EEPROM and/or the program ROM have to be exchanged.
Handling:
Perform a RAM Clear (
see part IV.9 - RAM Clear).
If the error cannot be cleared, the EEPROM and/or the program ROM have to be exchanged.
45M623N5UK-01
65 4 - EEPROM changed
Handling:
Perform a RAM Clear (
Handling:
Perform a RAM Clear (
69 0 - Blackbox inoperable
Handling:
Turn/release the attendant key.
If the error cannot be cleared, check the blackbox connection or exchange the blackbox
and/or the EEPROM.
Handling:
Turn/release the attendant key.
If the error cannot be cleared, exchange the blackbox and/or the EEPROM.
Handling:
Turn/release the attendant key.
If the error cannot be cleared, check the connectors and the cables of the 7 digit display.
P a g e
47
Handling:
Turn/release the attendant key.
If the error cannot be cleared, check the connectors and the cables of the 7 digit display.
Handling:
Turn/release the attendant key.
If the error cannot be cleared, check the connectors and the cables of the 7 digit display.
80 0 - Touch screen missing
Handling:
Turn/release the attendant key.
If the error cannot be cleared, check the connectors and the cables of the touch screen.
Check the power supply of the touch screen.
Exchange the touch screen or the touch screen controller.
Handling:
Turn/release the attendant key.
If the error cannot be cleared, check the connectors and the cables of the touch screen.
Check the power supply of the touch screen.
Exchange the touch screen or the touch screen controller.
Handling:
Turn/release the attendant key.
If the error cannot be cleared, check the connectors and the cables of the touch screen.
Check the power supply of the touch screen.
Exchange the touch screen or the touch screen controller.
Handling:
Turn/release the attendant key.
If the error cannot be cleared, check the connectors and the cables of the touch screen.
Check the power supply of the touch screen.
Exchange the touch screen or the touch screen controller.
99 9 - Internal Error
P a g e
48
Handling:
Perform a RAM Clear .
If the error cannot be cleared, note down the error message and inform
our Technical Support by phone number +43 2252 606-300.
45M623N5UK-01
IV.2 Remote in
ATTENTION
In countries where the remote function is prohibited by law this function must not be enabled
and/or has been disabled by the producer.
The assignment of the active buttons in the respective game is shown in the game complement.
How to execute a remote (available only in the idle mode and with closed Main Door):
45M623N5UK-01
1) Turn the attendant key (the machine switches to the AUDIT MENU).
2) Press the active buttons or in case of machines with touchscreen touch the respective fields to
go to the ATTENDANT menu.
P a g e
49
4) Press the respective buttons or in case of machines with touchscreen touch the respective fields to
add 1, 10, 100 or 1000 credits.
5) The selected credit is registered automatically on the remote meter
(or on the respective country-specific meter).
6) Release the attendant key.
45M623N5UK-01
The remote function can be used only if it has been enabled in the AUDIT MENU in
MACHINE SETUP > PARAMETER SETTINGS (
see part IV.8 - AUDIT MENU).
P a g e
50
ATTENTION
In countries where the handpay function is prohibited by law this function must not be enabled
and/or has been disabled by the producer.
The assignment of the active buttons in the respective game is shown in the game complement.
If a limit has been reached during a game, you can get to this page automatically by turning
the attendant key.
How to execute a handpay (available only in the idle mode and with closed Main Door):
45M623N5UK-01
1) Turn the attendant key (the machine switches to the AUDIT MENU).
2) Press the active buttons or in case of machines with touchscreen touch the respective fields to
go to the ATTENDANT menu.
P a g e
51
4) Press the respective buttons or in case of machines with a touchscreen touch the respective fields
to handpay the current credit.
5) The handpaid credit is registered automatically on the handpay meter.
6) Release the attendant key.
45M623N5UK-01
The handpay function can only be used if it has been enabled in the AUDIT MENU in
MACHINE SETUP > PARAMETER SETTINGS (
see part IV.8 - AUDIT MENU).
P a g e
52
The assignment of the active buttons in the respective game is shown in the game complement.
45M623N5UK-01
1) Turn the attendant key (the machine switches to the AUDIT MENU).
3) Press the active buttons or in case of machines with touchscreen touch the respective fields to
go to the ATTENDANT menu.
P a g e
53
5) Press the active buttons or touch the respective fields to enter the sum of the refilled amount
of coins.
6) The refilled amount is registered automatically. This amount must exactly relate to the coins refilled,
otherwise the accounting will be incorrect.
P a g e
54
ATTENTION
In countries where the hopper dump function is prohibited by law, this function must not be enabled
and/or has been disabled by the producer.
The assignment of the active buttons in the respective game is shown in the game complement.
45M623N5UK-01
2) Turn the attendant key (the machine switches to the AUDIT MENU).
3) Press the active buttons or in case of machines with touchscreen touch the respective fields
to go to the ATTENDANT menu.
P a g e
55
5) Press the active buttons or touch the respective fields to enter the sum of the amount to dump
in steps of 1, 10 or 100.
6) The dumped amount is registered automatically.
7) Close the Main Door.
45M623N5UK-01
P a g e
56
This function allows the attendant to lock the machine for the game play mode while it is switched on.
By using the Out of Service function it is not necessary to power down a defective machine but it may be
locked as long as the defect has not been repaired.
The assignment of the active buttons in the respective game is shown in the game complement.
45M623N5UK-01
1) Turn the attendant key (the machine switches to the AUDIT MENU).
2) Press the active buttons or in case of machines with touchscreen touch the respective fields
to go to the ATTENDANT menu.
P a g e
57
4) Press the active button or touch the field Enter to lock the machine.
45M623N5UK-01
P a g e
58
45M623N5UK-01
The top light indicates the different operational status (jackpot, error, service, etc.).
Novomatic Standard
Blue is lighting:
The light is flashing until the fist game has been finished.
The error message is indicated in case of error and the Main Door
or the Door-in-Door system is open.
Handpay is required.
After the handpay has been finished the lamps stop flashing.
P a g e
59
Bally France
Green is flashing:
Red is lighting:
Red is flashing:
Yellow is flashing:
P a g e
60
45M623N5UK-01
Depending on machine configuration the items described in this part may vary.
INFORMATION
The respective active buttons (illuminated) are located on the keyboard below the control panel
shown on the screen. See game supplement.
IV.8.1
ATTENDANT Menu
45M623N5UK-01
Turn the attendant key to enter the ATTENDANT menu. This menu shows the accounting and statistic,
and several settings may be made. The pages can be selected by pressing the active buttons or in case of
machines with touchscreen by touching the respective fields.
The left illustration shows the AUDIT MENU at closed Main Door, the right illustration shows the extended
AUDIT MENU at opened Main Door.
P a g e
61
Press the respective buttons or in case of machines with a touchscreen touch the respective fields to add
the desired amount (
see part IV.2 - Remote in).
The respective value and registered credit of each payment transaction are indicated.
Shows the credit added via the remote function.
CURRENT CREDIT
REMOTE IN
P a g e
62
45M623N5UK-01
CURRENT HANDPAY
CASHABLE CREDIT
FROM COIN
FROM BILL
FROM TICKET
TICKET SEMIPROMOTIONAL
SEMIPROMOTIONAL
CASHABLE
BANK
NONCASHABLE CREDIT
FROM TOKEN
TICKET PROMOTIONAL
TICKET NONCASHABLE
PROMOTIONAL
NONCASHABLE
ATTENTION
For each transaction, the monetary value and the corresponding credit amount are indicated.
Which kind of credit is deemed CASHABLE or NONCASHABLE may vary depending on the
jurisdiction.
P a g e
63
The number of coins, the respective value and the respective registered credit of each payment transaction
are indicated.
The number of coins, the respective value and the respective registered credit of each payment transaction
are indicated.
P a g e
64
45M623N5UK-01
45M623N5UK-01
This function allows the attendant to lock the machine for the game play mode while it is switched on
(
see part IV.6 - Out of Service).
P a g e
65
45M623N5UK-01
TOTAL IN
COINS IN
TOKEN IN
BILL IN
REMOTE IN
CARD IN
TICKET IN
Total value of all coins, tokens, tickets and bills inserted and credits added
via the remote function.
Total value of all coins inserted via the coin acceptor.
Total value of all tokens accepted.
Total value of all bills accepted.
Total value of all credits added via the remote function.
Total value of all credits inserted via cashless card.
Total value of all credits inserted via ticket.
TOTAL OUT
COINS OUT
HANDPAY
CARD OUT
TICKET OUT
Total value of all credits paid out (hopper, handpay, card and vouchers).
Total value of all coins paid out via the hopper.
Total value of all amounts paid out via handpay function.
Total value of credits added to the cashless card.
Total value of credits paid out via ticket printer.
TOTAL IN-OUT
The respective value and the respective registered credit of the payment transaction are indicated.
P a g e
66
45M623N5UK-01
TOTAL BET
TOTAL WON
MACHINE YIELD
TOTAL GAMES
Payout percentage.
Total number of all games played.
The respective value and the respective registered credit of the payment transaction are indicated.
P a g e
67
TICKET IN
CASHABLE
NONCASHABLE
PROMOTIONAL
TICKET OUT
CASHABLE
NONCASHABLE
PROMOTIONAL
Furthermore, the TOTAL NUMBER OF ACCEPTED TICKETS and the TOTAL NUMBER OF PRINTED
TICKETS are indicated on this page.
The respective value and the respective registered credit of the payment transaction are indicated.
P a g e
68
45M623N5UK-01
45M623N5UK-01
HANDPAY
CANCELLED CREDITS
WIN LIMIT JACKPOT
PROGRESSIVE JACKPOT
MYSTERY JACKPOT
TOTAL WIN
WIN TO CREDIT
JP WIN TO CREDIT
WIN TO HANDPAY
WIN TO CARD
WIN TO TICKET
TOTAL BONUS
DEDUCT. BONUS
NON DEDUCT. BONUS
WAGER M. BONUS
Total value of the additional win option (bonusing system via network).
Tax-deductible part of the bonusing system.
Non-deductible part of the bonusing system.
Wager according to bonusing system.
The respective value and the respective registered credit of the payment transaction are indicated.
P a g e
69
CHANNEL
VALUE ()
COUNT
CREDIT
TOTAL ()
45M623N5UK-01
CHANNEL
VALUE ()
COUNT
CREDIT
TOTAL ()
P a g e
70
45M623N5UK-01
CHANNEL
VALUE ()
COUNT
CREDIT
TOTAL ()
COINS TO HOPPER
HOPPER REFILL
HOPPER DUMP
HOPPER LEVEL
P a g e
71
Total value of all coins, tickets, tokens and bills inserted and credits added
via the remote function for a certain period.
Total value of all coins inserted via the coin acceptor for a certain period.
TOKEN IN
BILL IN
REMOTE IN
CARD IN
TICKET IN
PERIODIC OUT
COINS OUT
HANDPAY
CARD OUT
TICKET OUT
Total value of all coins paid out via the hopper for a certain period.
Total value of all credits paid out via the handpay function for a certain period.
Total value of all credits added to the cashless card for a certain period.
Total value of all credits paid out via ticket printer for a certain period.
PERIODIC IN-OUT
The respective value and the respective registered credit of each payment transaction are indicated.
P a g e
72
45M623N5UK-01
PERIODIC IN
COINS IN
Total value of all coins and bills that can be removed in a certain period.
Total value of all coins that can be removed from the drop box in a
certain period.
Total value of all tokens that can be removed for a certain period.
Total value of all coins available in the hopper for a certain period.
Total value of all coins diverted into the hopper via the coin acceptor in
a certain period.
Total value of all coins paid out via the hopper in a certain period.
45M623N5UK-01
BILLS TO DROP
Total value of all bills that can be removed from the stacker box in a
certain period.
HOPPER REFILL
HOPPER DUMP
Total value of all coins refilled directly into the hopper in a certain period.
Total value of all coins paid out via the hopper with the hopper dump
function in a certain period.
PERIODIC BET
PERIODIC WON
MACHINE YIELD
PERIODIC GAMES
The respective value and the respective registered credit of each payment transaction are indicated.
P a g e
73
TICKET IN
CASHABLE
NONCASHABLE
PROMOTIONAL
TICKET OUT
CASHABLE
NONCASHABLE
PROMOTIONAL
Total value of all tickets paid out via the ticket printer in a certain period.
Total value of cashable tickets paid out via the ticket printer in a certain period.
Total value of non-cashable tickets paid out via the ticket printer in a
certain period.
Total value of promotional tickets paid out via the ticket printer in a
certain period.
Furthermore, the TOTAL NUMBER OF ACCEPTED TICKETS in certain period and the TOTAL NUMBER
OF PRINTED TICKETS in a certain period are indicated on this page.
The respective value and the respective registered credit of each payment transaction are indicated.
P a g e
74
45M623N5UK-01
45M623N5UK-01
HANDPAY
CANCELLED CREDITS
WIN LIMIT JACKPOT
PROGRESSIVE JACKPOT
MYSTERY JACKPOT
TOTAL WIN
WIN TO CREDIT
JP WIN TO CREDIT
WIN TO HANDPAY
WIN TO CARD
WIN TO TICKET
TOTAL BONUS
DEDUCT. BONUS
NON DEDUCT. BONUS
WAGER M. BONUS
Total value of the additional win option (bonusing system via network)
in a certain period.
Tax-deductible part of the bonusing system in a certain period.
Non-deductible part of the bonusing system in a certain period.
Wager according to bonusing system in a certain period.
The respective value and the respective registered credit of the payment transaction are indicated.
P a g e
75
CHANNEL
VALUE ()
COUNT
CREDIT
Total value of credits inserted via the respective bill channel in a certain period.
CHANNEL
VALUE ()
COUNT
CREDIT
TOTAL ()
45M623N5UK-01
TOTAL ()
P a g e
76
CHANNEL
VALUE ()
COUNT
CREDIT
COINS TO HOPPER
HOPPER REFILL
HOPPER DUMP
45M623N5UK-01
TOTAL ()
HOPPER LEVEL
in a certain period.
Total value of credits inserted via the respective hopper channel
in a certain period.
P a g e
77
P a g e
78
45M623N5UK-01
BET
WIN
REMOTE
HANDPAY
BILLS
DROP
GAMES
TOKEN
ATTENTION
45M623N5UK-01
MAIN DOOR
LAST OPEN
LAST CLOSE
OPEN COUNT
GAMES SINCE LAST CLOSE
Monitored status.
Date and time of last opening of the Main Door.
Date and time of last closing of the Main Door.
Number of openings of the Main Door.
Number of games played since last closing of the Main Door.
DOOR IN DOOR
LAST OPEN
LAST CLOSE
OPEN COUNT
GAMES SINCE LAST CLOSE
Monitored status.
Date and time of last opening of the Door-in-Door.
Date and time of last closing of the Door-in-Door.
Number of openings of the Door-in-Door.
Number of games played since last closing of the Door-in-Door.
Monitored status.
Date and time of last opening of the Drop Door.
Date and time of last closing of the Drop Door.
Number of openings of the Drop Door.
Number of games played since last closing of the Drop Door.
P a g e
79
BILL DOOR
LAST OPEN
LAST CLOSE
OPEN COUNT
GAMES SINCE LAST CLOSE
Monitored status.
Date and time of last opening of the Stacker Door.
Date and time of last closing of the Stacker Door.
Number of openings of the Stacker Door.
Number of games played since last closing of the Stacker Door.
LOGIC AREA
POWER ON AFTER OPEN
OPEN COUNT
GAMES SINCE LAST CLOSE
Monitored status.
Date and time of last opening of the Logic Door.
Number of openings of the Door-in-Door.
Number of games played since last closing of the Logic Door.
METER CONNECT
LAST OPEN
LAST CLOSE
OPEN COUNT
GAMES SINCE LAST CLOSE
Monitored status.
Date and time of last disconnection of the mechanical meters.
Date and time of last connection of the mechanical meters.
Number of disconnections of the mechanical meters.
Number of games played since last connection of the
mechanical meters.
P a g e
80
45M623N5UK-01
POWER FAIL
LAST POWER FAIL
LAST POWER ON
POWER FAIL COUNT
GAMES SINCE LAST POWER FAIL
Monitored status.
Date and time of last power down.
Date and time of last power on.
Number of power downs.
Number of games played since last power down interruption.
45M623N5UK-01
P a g e
81
IIV.8.3
DIAGNOSTIC Menu
45M623N5UK-01
MACHINE NUMBER
MACHINE
EEPROM CONFIGURATION
KERNEL
MAINBOARD VERSION
MAINBOARD SERIAL NUMBER
BACKPLANE VERSION
GAME
P a g e
82
45M623N5UK-01
P a g e
83
45M623N5UK-01
LAMP TEST
BUTTON TEST
P a g e
84
Select the function VIDEO TEST to show the test chart on the screen.
In case of eventual distortions or a defective colour reproduction the monitor can be readjusted according
to this test chart.
45M623N5UK-01
Press the respective buttons or touch the respective fields to start the audio test.
07 2008 AGI GmbH
P a g e
85
Select the function TOUCH SCREEN TEST to check the calibration and functionality of the touchscreen.
Touch the screen at different places. At each touch a white point is enlightened on the screen.
45M623N5UK-01
Select the function HOPPER TEST to check the functionality of the hopper.
Follow the instructions indicated on the screen. Coins inserted are not registered!
P a g e
86
The BILL ACCEPTOR TEST function can be used to check the functionality of the bill acceptor.
45M623N5UK-01
ATTENTION
If a bill is not detected, the reason may be that the insertion direction is not enabled in the menu item
MACHINE > BILL SETTINGS or the software is not programmed to accept the bill.
Select the function COIN DIVERTER TEST to test the functionality of the coin diverter.
Press the respective button or touch the respective field to switch the coin diverter ON or OFF.
P a g e
87
IV.8.4
45M623N5UK-01
All errors including date and time when they have occurred are listed.
The error codes and error messages correspond to those listed in part IV.1.2.
In case of an overflow the respective oldest entries are overwritten.
P a g e
88
All accepted bills including date and time of their insertion are listed.
In case of an overflow the respective oldest entries are overwritten.
45M623N5UK-01
Lists all handpay events including date and time when they where paid out.
In case of an overflow the respective oldest entries are overwritten.
P a g e
89
All accepted card credits including date and time are listed.
In case of an overflow the respective oldest entries are overwritten.
45M623N5UK-01
Lists all external jackpots including date and time when they where hit.
In case of an overflow the respective oldest entries are overwritten.
P a g e
90
Lists all ticket events including validation number, value, ticket number, date and time.
In case of an overflow the respective oldest entries are overwritten.
45M623N5UK-01
Lists all ticket events including validation number, value, ticket number, date and time.
In case of an overflow the respective oldest entries are overwritten.
P a g e
91
IV.8.5
GAME HISTORY
Date
Time
Credit bef.
Bet
Win
Gambles
Gamble in
Gamble out
P a g e
92
45M623N5UK-01
GAME HISTORY
Game
Phase
IV.8.6
45M623N5UK-01
The game statistic depend on the selected game. If different bets (BET) are permitted in the game, the
first page always indicates the total statistic (BET - independent) and each BET available is represented
separately (e.g. page 2 = BET 1, page 3 = BET 2, etc.).
P a g e
93
IV.8.7
45M623N5UK-01
On this page several functions specific to the selected game can be featured.
P a g e
94
IV.8.8
45M623N5UK-01
INFORMATION
In comparison to the CREDIT LIMIT the CREDIT IN LIMIT must always be lower by AT LEAST the value
represented by the highest configuration bill (coin, token).
This ensures that by insertion of a bill (coin, token) only the CREDIT IN LIMIT may be reached and never
the CREDIT LIMIT.
CREDIT IN LIMIT
0...
If the limit has been reached, no more credits can be added (coin and
bill acceptor are blocked), also the remote function is disabled.
No CREDIT IN LIMIT.
CREDIT LIMIT
0...
JACKPOT LIMIT
0...
P a g e
95
CELEBRATION LIMIT
DOUBLE UP LIMIT
Maximum number of coins that can be paid out via the hopper, if the
CASH button has been pressed or in case of wins. All amounts in
excess have to be paid out via the handpay function.
No HOPPER LIMIT.
Maximum amount that can be paid out via the ticket printer.
All amounts in excess have to be paid out via the handpay function.
No TICKET LIMIT.
COINS IN LIMIT
0...
MINIMUM HANDPAY
EVEN HANDPAY
Press the corresponding buttons or touch the respective fields to perform the desired settings.
In each case a MIN and a MAX value are indicated in the range of which the current value can be set.
Due to regulation some value ranges may be limited or the possibility of setting may be prohibited
in general.
P a g e
96
45M623N5UK-01
Press the corresponding buttons or touch the respective fields to perform the desired settings.
INFORMATION
45M623N5UK-01
Depending on the game configuration and the game some of the following functions listed below may not
be available!
START MODE
0... RE-BET AT START
1... BET AND START
2... AUTOSTART
REMOTE INPUT
0... DISABLED
1... ENABLED
HANDPAY CREDIT
0... DISABLED
1... ENABLED
BILL INPUT
0... TO HOPPER
1... TO CREDIT
2... TO CREDIT/COMPULSORY GAME
3... TO CREDIT/PLAY 50%
P a g e
97
WIN OUTPUT
0... TO HOPPER
1... TO CREDIT
HOPPER REMAINDER
0... TO CREDIT
1... TO HANDPAY
2... CREDIT + HANDPAY
LANGUAGE
0... ENGLISH
1... GERMAN
2... SPANISH
3... PORTUGUESE
P a g e
98
45M623N5UK-01
COIN INPUT
0... TO BET
1... TO BET/START
2... TO BET/TO CREDIT
3... TO CREDIT
4... TO CREDIT/CANCEL
45M623N5UK-01
HOPPER DUMP
0... DISABLED
1... ENABLED
HOPPER STRATEGY
0... HIGH VALUE + RETRY
1... HIGH VALUE
2... BALANCED
Determines the way payout is handled when two hoppers are used.
If the first hopper is already empty, the machine switches over to the
second hopper for payout.
High-value coins are preferred for payout, the remaining amount is
paid out in lower-value coins.
Wins are paid out with a balanced number of both high-value and
low-value coins.
WINCOUNTER SPEED
0... SLOW
1... FAST
BONUSING
0... DISABLED
1... ENABLED
TICKET REDEMPTION
0... DISABLED
1... ENABLED
P a g e
99
45M623N5UK-01
BILL ACCEPTOR X
CHANNEL
VALUE
ENABLE
DIRECTION
The bill acceptor and the coin acceptor are disabled when the are close to the CREDIT IN LIMIT.
COIN ACCEPTOR X
CHANNEL
VALUE
ENABLE
P a g e
100
45M623N5UK-01
HOPPER X
CHANNEL
HOPPER FULL LEVEL
HOPPER LOW LEVEL
HOPPER REFILL LEVEL
ENABLE
P a g e
101
DENOMINATION
CURRENCY
MAIN COIN
TOKENISATION
MAXIMUM BET
MAXIMUM BET PER ROW
LA WIN LIMIT
GAME WIN LIMIT
ALARM SOUND
MACHINE NUMBER
TYPE OF VALIDATION
P a g e
102
45M623N5UK-01
45M623N5UK-01
If an ethernet network is used, this pages indicate the currently adjusted settings for the network protocol.
NETWORK PROTOCOL
NETWORK ADDRESS
FEATURES
CONTROL
CASHLESS
BONUSING
TICKET VALIDATION
TICKET REDEMPTION
PROGRESSIVE JACKPOT
MYSTERY JACKPOT
If this feature is enabled, several machine settings can be adjusted via the
network server (i.e. to enable coin channels, bill acceptor).
Enables/disables the cashless card system.
To use a cashless card system, this feature has to be enabled.
Enables/disables a bonusing system via network (additional winning
option).
Enables/disables the ticket printer. To use a ticket printer for payout of
credits, this feature has to be enabled (ON), because this requires a
network protocol. The network protocol depends on the country of
installation. For some countries a second network protocol may be
required.
Enables/disables ticket accepting via bill acceptor. For ticket redemption via
bill acceptor this feature has to be enabled (ON), because this requires a
network protocol. The network protocol depends on the country of
installation. For some countries a second network protocol may be
required.
Enables/disables the jackpot control via the network protocol. The
progressive jackpot is triggered depending on a default win combination.
Enables/disables the jackpot control via the network protocol.
The mystery jackpot is triggered by a random process, independent of bets
or game events.
LINK TYPE
CASHLESS TYPE
P a g e
103
45M623N5UK-01
JACKPOT PROTOCOL
JACKPOT ADDRESS
PROGRESSIVE GAME
SHOW WIN
JACKPOT LEVEL X
P a g e
104
DENOMINATION
BILL ACCEPTOR X
CHANNEL
BILL
TOKENISATION
45M623N5UK-01
DENOMINATION
COIN ACCEPTOR X
CHANNEL
COIN
TOKENISATION
P a g e
105
DENOMINATION
HOPPER X
CHANNEL
COIN
TOKENISATION
45M623N5UK-01
P a g e
106
IV.8.9
CALIBRATION Menu
45M623N5UK-01
yyyy-MMM-dd HH:mm:ss
Current date and time. Press the respective buttons or touch the
respective fields to perform the settings.
P a g e
107
45M623N5UK-01
P a g e
108
INFORMATION
Until this moment the RAM Clear may avoided if the machine is powered down before
a button is pressed.
45M623N5UK-01
EEPROM
Coolfire Kopie.eps
P a g e
109
45M623N5UK-01
P a g e
11 0
45M623N5UK-01
Part V
Hardware
V.1
Power supply
V.2
Bill acceptor
V.3
Coin acceptor
V.4
Hopper
V.5
V.6
COOLFIRE Motherboard
V.7
COOLFIRE Backplane
V.8
Top light
V.9
Illumination
V.10
Mechanical meters
V.11
Door optics/switches
V.12
Loudspeakers
V.13
Preventative maintenance
45M623N5UK-01
HARDWARE
There are static-sensitive parts inside the machine which could be damaged by electric
discharge. Ground yourself by touching a ground strap inside the machine to neutralize
electric charges before changing or maintaining inner parts.
P a g e
11 2
HARDWARE
Description of components
7
8
1
45M623N5UK-01
10
12
14
16
11
13
15
17
18
19
FV623_Komponenten.eps
11 Bill acceptor
12 COOLFIRE Backplane
13 Stacker door with lock
14 Hopper
15 Door optics (receiver)
16 Ticket printer (optional)
17 Switching power supply (behind stacker)
18 Main switch
19 Drop door with lock
P a g e
11 3
HARDWARE
Block diagram:
main power supply
option:
coin acceptor
NFS distributor
option:
printer / jackpot controller
COOLFIRE
motherboard
X25
level unit
X21
backplane supply
reel supply
buttons &
lamps
X26
X7/X8/X13/X17
X19
WBA illumination
toplight
X10/X11/X33
VFD display
X3
coin diverter
X6
reel print
coin channel optics
X5
touchscreen
X18
P 384
backplane
X15
X31
X22
doorswitch (BNP)
X24
1. monitor (VGA)
2. monitor (VGA)
X9
meters
X16
loudspeakers
left / right
X4
hopper
X12/X30/X32
X27
data
supply
power expansion
bill acceptor
X20/X28
network
(online systems)
X23
X2/X14
RS 485 network
IDE
45M623N5UK-01
Blockschaltbild_UK1.eps
P a g e
11 4
HARDWARE
V.1
Power supply
V.1.2
Function
V.1.3
Troubleshooting
V.1.4
45M623N5UK-01
V.1.1
P a g e
11 5
45M623N5UK-01
HARDWARE
There are static-sensitive parts inside the machine which could be damaged by electric
discharge. Ground yourself by touching a ground strap inside the machine to neutralize
electric charges before changing or maintaining inner parts.
P a g e
11 6
HARDWARE
V.1.1
V.1.2
Function
24 V / DC for:
Hopper
12 V / DC for:
Hopper
COOLFIRE Backplane
COOLFIRE Backplane
5 V / DC for:
V.1.3
Troubleshooting
V.1.4
45M623N5UK-01
If any defects cannot be repaired, the defective switching power supply has to be exchanged.
F_623_SchaltnetzteilAusbau.jpg
Dismounting instructions for the switching power supply (see illustr. V.1.1):
1) Open the Main Door and disconnect the machine from the mains.
2) Remove the hopper cover and take out the hopper in forward direction.
3) Disconnect all connectors from the switching power supply.
4) Release the fixing devices.
5) Pull out the switching power supply in left direction and exchange it.
6) Assemble the switching power supply in reverse order.
P a g e
11 7
45M623N5UK-01
HARDWARE
P a g e
11 8
HARDWARE
45M623N5UK-01
V.2
Bill acceptor
V.2.1
V.2.2
Function
V.2.3
Troubleshooting
V.2.4
V.2.5
V.2.6
Empty stacker
V.2.7
V.2.8
P a g e
11 9
45M623N5UK-01
HARDWARE
There are static-sensitive parts inside the machine which could be damaged by electric
discharge. Ground yourself by touching a ground strap inside the machine to neutralize
electric charges before changing or maintaining inner parts.
P a g e
120
HARDWARE
V.2.1
V.2.2
Troubleshooting
V.2.4
If any defects cannot be repaired, the defective bill acceptor has to be exchanged.
45M623N5UK-01
Function
V.2.3
WBA25_624.eps
SC83_imGeraet.eps
P a g e
121
HARDWARE
F_CashFlow_Ausbau.eps
Illustr. V.2.3
SC83_Einbau.eps
Transfer unit
cover
Latches
Bill slot
Stacker box
SC83_Komponenten.eps
P a g e
122
45M623N5UK-01
V.2.5
WBA 3D.eps
HARDWARE
V.2.6
Empty stacker
Stackertausch 3D.eps
45M623N5UK-01
SC83_Stacker1.eps / SC83_Stacker2.eps
ATTENTION
P a g e
123
HARDWARE
V.2.7
in the sensors
Depending on the situation encountered jammed bills must be removed as shown in illustr. V.3.8.
45M623N5UK-01
ATTENTION
You must remove the acceptor module from the chassis to open the front sensor area!
P a g e
124
ATTENTION
HARDWARE
V.2.8
The adjustment of the sensors is intended to compensate any slight age-related cloudiness of the
optical lenses (black and white adjustment) or any normal wear of the optical sensors.
Therefore, the adjustment procedure described below should be carried out when required.
Note: The adjustment is not a substitute for cleaning the sensor lenses!
The sensor lenses should also be cleaned before each sensor adjustment.
The below instructions should be followed strictly!
Description:
1) Release the connecting plugs from the WBA (e.g. by pulling out the acceptor unit).
2) Set DIP switches
45M623N5UK-01
8, 7, 6 and 5 to ON
1, 2, 3 and 4 to OFF
3) Connect the WBA to the power supply (by inserting the acceptor unit in the acceptor frame).
WBA.eps
4) The emergency transport motor will first run forward approx. 2 seconds and then briefly reverse.
5) Now the reference paper KS-039 (EDP item no. 075626) can be inserted with the black end in first.
The WBA pulls the paper in automatically and moves it forward and backwards several times.
6) The auto-adjustment is completed once the reference paper has been ejected and the transport
motor has come to a halt. After that, the acceptor requires approx. another 2 - 3 seconds to write
the data to the internal memory chip.
7) Disconnect the acceptor unit from the power supply again and return the DIP switches to their
original status, which will normally be all switches in OFF position.
P a g e
125
45M623N5UK-01
HARDWARE
P a g e
126
HARDWARE
45M623N5UK-01
V.3
Coin acceptor
V.3.1
V.3.2
Function
V.3.3
Troubleshooting
V.3.4
V.3.5
Programming
V.3.6
V.3.7
Teach Mode
P a g e
127
45M623N5UK-01
HARDWARE
There are static-sensitive parts inside the machine which could be damaged by electric
discharge. Ground yourself by touching a ground strap inside the machine to neutralize
electric charges before changing or maintaining inner parts.
P a g e
128
HARDWARE
V.3.1
V.3.2
Function
The coin diverter below the coin acceptor sorts the coins into either the hopper or drop box.
V.3.3
Troubleshooting
If any defects of the coin acceptor cannot be repaired, the defective component has to be exchanged.
1) Open the Main Door and disconnect the machine from the mains.
2) Check if the coin acceptor is fixed correctly in its mounting.
45M623N5UK-01
P a g e
129
HARDWARE
V.3.4
If any defects of the coin acceptor cannot be repaired, the complete component has to be exchanged.
F_MnzprferAusbau.eps
Mnzkanallichtschranke.eps
Dismounting instructions for the coin acceptor NRI-G13 (see illustr. V.3.1):
1) Open the Main Door and disconnect the machine from the mains.
2) Take out the coin acceptor by grabbing it on the upper edge and pull it out from the brackets.
3) Disconnect the plug connectors between machine and coin comparitor.
4) Assemble the coin acceptor in reverse order.
Dismounting instructions for the coin comparitor MC-40 (see illustr. V.3.2):
1) Open the Main Door and disconnect the machine from the mains.
2) Press down the levers of the coin comparitor lock and take out the coin comparitor from its mounting.
Release the connectors.
3) Unscrew the coin optics board and release the connectors (only if the board is defective).
4) Exchange the coin comparitor (or the optics board).
5) Assemble the coin comparitor and the coin optics board in reverse order.
P a g e
130
45M623N5UK-01
HARDWARE
V.3.5
Programming (NRI-G13)
The coin acceptor NRI-G13 is already programmed for the currency of the country of installation.
Programmed currencies and coins are described on the coin acceptor label. Programming of new
coins or currencies is carried out through the DIP switches on the backside of the coin acceptor.
45M623N5UK-01
P a g e
131
HARDWARE
V.3.6
Starting with model no. G-13/1 the validator offers the possibility to have two configurations, independent
from each other. To each of these blocks 12 individual coin channels are assigned with appropriate
tables (signals, denominations, sorting information). The programming is done either at NRI or at a
service station.
Although both blocks are programmed you can only work with one of them.
This type of validator can be recognized by the label with the extended indications.
This function is ideal for storing additionally to the actual currency a second coin combination with
individual interface information (table). For example in case of a currency conversion the actual
settings are deactivated and the new ones are activated. A further application can be if independent
from currency and alternative vending machine interface is selected.
On the rear of the NRI G-13 two switch arrangements are positioned. For switching over from
block 0 to block 1 please use switch no. 8 of the right-hand switch arrangement. Please proceed
as follows:
P a g e
132
45M623N5UK-01
HARDWARE
V.3.7
Teach Mode
By using the teach mode you can programme coins or token in channel 10 and 11. In all versions
of the G-13 validator the teach mode is programmable. However, a combination of the 2-price-totalizer
with sales counter and the teach mode does not make sense as the tasks of the switch for single coins
inhibit for the 12th channel would overlap each other.
45M623N5UK-01
1) On the rear of the validator two Dual-In-Line switches are positioned. Switch no. 12 ON.
2) Depending on the intention to teach channel 10 or 11, please switch ON the appropriate switch.
3) Insert coins or token.
After insertion of the 10th coin (token) the validator gives an acoustic signal (click of the
acceptance gate). The measured values are now registered.
4) Turn switch no. 12 OFF.
5) Also turn appropriate switch for channel 10 or 11 OFF.
Once again the acceptance gate gives an acoustic signal (1 time), i.e. the programming has
been finished successfully.
Channel
10
11
12
13
ON
14
OFF
MP DIL_englisch.eps
In case the acceptance rate for a coin or token programmed by teach mode is not sufficient, you can
programme the coin or token with wider acceptance bandwidths. Therefore please
do the following:
1) DIL switch no. 12 ON. Teach mode is now active.
2) Turn switch for desired channel 10 or 11 ON.
3) Insert new coin or token at least 10 times.
The acceptance gate gives an acoustic signal (1 time). Coin values are registered.
4) Turn channel no. 10 and 11 ON.
Wide acceptance bandwidths are now calculated.
5) Turn switch no. 12 OFF.
6) Turn switch 10 and 11 OFF.
Coin or token is now programmed. The teach mode has now been finished and
the channel 10 and 11 are enabled.
P a g e
133
HARDWARE
45M623N5UK-01
P a g e
134
HARDWARE
45M623N5UK-01
V.4
Hopper
V.4.1
V.4.2
Function
V.4.3
Troubleshooting
V.4.4
V.4.5
Hopper high-level
P a g e
135
45M623N5UK-01
HARDWARE
There are static-sensitive parts inside the machine which could be damaged by electric
discharge. Ground yourself by touching a ground strap inside the machine to neutralize
electric charges before changing or maintaining inner parts.
P a g e
136
HARDWARE
V.4.1
V.4.2
Function
Storage of coins inserted by means of a diverter control system and payout of the wins.
V.4.3
Troubleshooting
Check if the hopper and the connectors are fixed correctly in their mounting.
Check if the hopper is pushed all the way in and if it is connected to the multi interface.
In addition, check if a coin is stuck and if the hopper needs cleaning.
45M623N5UK-01
V.4.4
F_Hopper.jpg
P a g e
137
HARDWARE
V.4.5
Hopper high-level
45M623N5UK-01
Two contact plates are located at the top inside the hopper. When the high level of the hopper is reached,
i.e. the two contact plates are reached, another 10 coins are diverted to the hopper. All coins inserted
afterwards are diverted to the drop box by means of the coin diverter system
(
see part IV.8 - AUDIT MENU > MACHINE > HOPPER SETUP).
P a g e
138
HARDWARE
45M623N5UK-01
V.5
Monitors
V.5.1
V.5.2
Function
V.5.3
Troubleshooting
V.5.4
V.5.5
P a g e
139
45M623N5UK-01
HARDWARE
There are static-sensitive parts inside the machine which could be damaged by electric
discharge. Ground yourself by touching a ground strap inside the machine to neutralize
electric charges before changing or maintaining inner parts.
P a g e
140
HARDWARE
V.5.1
V.5.2
Troubleshooting
Check if the monitors and the connectors of the cables are fixed correctly in their mounting.
V.5.4
45M623N5UK-01
Function
The monitors show the game play, the error messages and the audit system.
V.5.3
F_623-V05_unten1.eps
623-V05_unten2.eps
P a g e
141
HARDWARE
F_623-V05_oben1.eps
F_623-V05_oben2.eps
1) Open the Main Door and disconnect the machine from the mains.
2) Open the upper monitor retainer inside the machine by lifting and turning it forward (see illustr. V.5.2).
3) Disconnect the plug and cable connectors of the monitor which has to be exchanged.
Do not touch circuit board! High voltage!
4) Disconnect the security chain on the left side.
5) Grab the monitor with both hands and take it out of its retainer.
6) Exchange the defective monitor.
7) Assemble the monitor in reverse order.
P a g e
142
45M623N5UK-01
HARDWARE
V.5.5
At the rear of the monitor, a print is attached for the adjustment of brightness, contrast and
geometry of the picture.
A
B
C
D
E
F_Einstellung_Monitor.eps
45M623N5UK-01
Adjustment
The monitors can be adjusted via the buttons on the rear side of the respective monitor.
P a g e
143
45M623N5UK-01
HARDWARE
P a g e
144
HARDWARE
45M623N5UK-01
V.6
COOLFIRE Motherboard
V.6.1
V.6.2
Function
V.6.3
Troubleshooting
V.6.4
V.6.5
DIP switch
V.6.6
P a g e
145
45M623N5UK-01
HARDWARE
There are static-sensitive parts inside the machine which could be damaged by electric
discharge. Ground yourself by touching a ground strap inside the machine to neutralize
electric charges before changing or maintaining inner parts.
P a g e
146
HARDWARE
V.6.1
V.6.2
ATTENTION
When pushing in the COOLFIRE motherboard make sure that the connectors lock in correctly to the
COOLFIRE backplane.
V.6.3
45M623N5UK-01
Function
Troubleshooting
If any defects of the COOLFIRE motherboard (mainboard) cannot be repaired, the board has to be
exchanged.
V.6.4
F_623CF_Tausch.eps
P a g e
147
HARDWARE
V.6.5
Coolfire Kopie.eps
P a g e
148
45M623N5UK-01
DIP switch
HARDWARE
V.6.6
F_MotherboardBest.eps
Illustr. V.6.3 Position game selector (1), game software (2), EEPROM (3)
45M623N5UK-01
P a g e
149
HARDWARE
F_MotherboardBest.eps
45M623N5UK-01
ATTENTION
EEPROM+Sockel.eps
!
P a g e
150
ATTENTION
After the components have been exchanged, a RAM Clear may be necessary!
07 2008 AGI GmbH
HARDWARE
45M623N5UK-01
V.7
COOLFIRE Backplane
V.7.1
V.7.2
Function
V.7.3
V.7.4
Pin assignment
V.7.5
Troubleshooting
V.7.6
P a g e
151
45M623N5UK-01
HARDWARE
There are static-sensitive parts inside the machine which could be damaged by electric
discharge. Ground yourself by touching a ground strap inside the machine to neutralize
electric charges before changing or maintaining inner parts.
P a g e
152
HARDWARE
V.7.1
V.7.2
Function
The COOLFIRE backplane is responsible for all input and output signals of the main electronic unit.
V.7.3
X16
X21
LED colour
function
red
+5 V
yellow
+12 V
green
+24 V
yellow
-12 V
X31
J2
J3 J7
J6
J1
LED colour
function
rot
release WBA
X25
X26
X23
X1
45M623N5UK-01
X22
1
X4
X27
X24
X10
X11
X33
X30
X12
X32
X9
X2 X17
X13
X7
X8
X6
X5
X15
X14
X3
X18
X19
J4
X28
F_CF_384_3.jpg
X20
HARDWARE
V.7.4
Pin assignment
P a g e
154
PIN
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
FUNCTION
+5V DC
+5V DC
GND
GND
GND
GND
+12V DC
+12V DC
-12V DC
-12V DC
NTXD IN1
NTXD OUT
NTXD IN2
NTXD OUT
NRTS IN1
NRTS OUT
NRTS IN2
NRTS OUT
NRXD OUT
NRXD IN
Receiver OUTPUT_D
Receiver INPUT_D
NCTS OUT
NCTS IN
Receiver OUTPUT_C
Receiver INPUT_C
RS 232
+/- 12V DC
TX
pin 11/12
pin 13/14
RX
pin 19/20
pin 19/21
pin 20/22
RTS
pin 15/16
pin 17/18
CTS
pin 23/24
pin 23/25
pin 24/26
45M623N5UK-01
Connector X1
Jumper for RS 232 Level (26 pin male connector)
HARDWARE
45M623N5UK-01
Connector X2
EBA bill acceptor (26 pin male connector)
PIN
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
FUNCTION
+12V DC
BAGND
+12V DC
BAGND
VEND1
GND
VEND2
GND
VEND3
GND
BUSY
GND
ABN
GND
+5V DC
INH
+5V DC
nACK
+5V DC
nREJ
DATA VALID
GND
STK FULL
GND
N.C.
N.C.
Connector X3
VFD display (10 pin Lock Header)
PIN
01
02
03
04
05
06
07
08
09
10
FUNCTION
+5V DC
GND
D-TX
D-DTR
D-RTS
N.C.
D-RX
N.C.
N.C.
D-RI
Connector X4
Network (8 pin Mini Fit Header)
PIN
01
02
03
04
05
06
07
08
FUNCTION
+5V DC
GND
+12V DC
-12V DC
NTXD
NRTS
NRXD
NCTS
Connector X5
Coin channel optics (5 pin Lock Header)
PIN
01
02
03
04
05
FUNCTION
+12V DC
GND
C_CH_A
C_CH_B
C_CH_C
Connector X6
Coin diverter (3 pin Lock Header)
PIN
01
02
03
FUNCTION
nCCHS1
nCCHS2
+12V DDC
Connector X7
NRI coin acceptor (10 pin male connector)
PIN
01
02
03
04
05
06
07
08
09
10
FUNCTION
NRI-GND
+12V DC
KAN5
KAN6
REJECT
nNRI-ENABLE
KAN1
KAN2
KAN3
KAN4
P a g e
155
HARDWARE
PIN
01
02
03
04
05
06
07
08
FUNCTION
TILT
N.C.
nCC-CREDIT
CC-GND
+12V DC
nCC-ENABLE
nCC-SENSE
GND
Connector X9
Mechanical meters (15 pin D-Sub female connector)
PIN
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
FUNCTION
nMETER1
nMETER2
nMETER3
METER4
METER5
METER6
LAMPSON
METERCOUNT
L_AREA1
GND
GND
nMETER7
nMETER8
+12V DC
+12V DC
PIN
01
02
03
04
05
06
07
08
09
10
11
12
FUNCTION
+5V-PS
GND
+12V-L
PGND
+24V DC
BAGND
+5V-PS
GND
+12V-PS
PGND
nPFI
-12V DC
Connector X12
Hopper 2 (14 pin Mini Fit Header)
PIN
01
02
03
04
05
06
07
08
09
10
11
12
13
14
FUNCTION
H2_M+
H2_M+12V DC
GND
HIGH LEVEL
LOW LEVEL
COIN OUT
SECURITY
H2_INP1
H2_INP2
H2_INP3
+24V DC
PGND
+5V DC
Connector X13
NRI coin acceptor (only 1 channel)
(10 pin male connector)
PIN
01
02
03
04
05
06
07
08
09
10
45M623N5UK-01
Connector X8
CC coin acceptor (8 pin Lock Header)
FUNCTION
CC-GND
+12V DC
N.C.
N.C.
N.C.
nCC-ENABLE
N.C.
nCC-CREDIT
N.C.
N.C.
Connector X14
WBA bill acceptor (10 pin Mini Fit Header)
PIN
01
02
03
04
05
06
07
08
09
10
FUNCTION
+12V DC
nBA-RESET
+12V DC
GND
LED+
BAGND
BA-TXD
BA-RXD
LEDN.C.
07 2008 AGI GmbH
HARDWARE
Connector X15
WBA illumination (4 pin Lock Header)
PIN
01
02
03
04
FUNCTION
Connector X16
Loudspeakers (4 pin Mini Fit Header)
PIN
01
02
03
04
FUNCTION
45M623N5UK-01
PIN
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
PIN
01
02
03
04
05
06
07
08
09
FUNCTION
B-DCD
B-RX
B-TX
B-DTR
GND
B-DSR
B-RTS
B-CTS
B-RI
Connector X19
Jackpot controller (15 pin D-Sub male connector)
Connector X17
Cash Flow coin acceptor (16 pin male connector)
Connector X18
Touchscreen (9 pin D-Sub male connector)
FUNCTION
PIN
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
FUNCTION
C-DCD
C-RX
C-TX
C-DTR
GND
GND
GND
GND
C-DSR
C-RTS
C-CTS
C-RI
N.C.
N.C.
N.C.
PIN
01
02
03
04
FUNCTION
N.C.
Signal A
Signal B
N.C.
P a g e
157
HARDWARE
P a g e
158
PIN
A01
A02
A03
A04
A05
A06
A07
A08
A09
A10
A11
A12
A13
A14
A15
A16
A17
A18
A19
A20
A21
A22
A23
A24
A25
A26
A27
A28
A29
A30
A31
A32
FUNCTION
GND
AOUT1GND
+5V-MB
IN2
GMD
IN12
IN6
GND
+5V-MB
OUT2
OUT9
GND
OUT6
OUT13
GND
+5V-MB
IN26
IN20
GND
IN30
IN24
GND
+5V-MB
OUT26
OUT21
GND
OUT30
IN33
IN42
GND
+5V-MB
PIN
B01
B02
B03
B04
B05
B06
B07
B08
B09
B10
B11
B12
B13
B14
B15
B16
B17
B18
B19
B20
B21
B22
B23
B24
B25
B26
B27
B28
B29
B30
B31
B32
FUNCTION
L_AREA1
+12V-MB
AOUT2+
IN1
IN10
IN11
IN5
IN14
IN15
IN16
OUT3
OUT10
OUT12
OUT7
OUT14
OUT16
IN25
IN19
IN28
IN29
IN23
IN32
OUT18
OUT20
OUT27
OUT22
OUT24
OUT31
IN41
IN35
IN36
IN37
PIN
C01
C02
C03
C04
C05
C06
C07
C08
C09
C10
C11
C12
C13
C14
C15
C16
C17
C18
C19
C20
C21
C22
C23
C24
C25
C26
C27
C28
C29
C30
C31
C32
FUNCTION
AOUT1+
+12V-MB
AOUT2IN9
IN3
IN4
IN13
IN7
IN8
OUT1
OUT4
OUT11
OUT5
OUT8
OUT15
IN17
IN18
IN27
IN21
IN22
IN31
OUT17
OUT19
OUT25
OUT28
OUT23
OUT29
OUT32
IN34
IN43
IN44
IN45
45M623N5UK-01
Connector X21
COOLFIRE motherboard (96 pin female connector)
45M623N5UK-01
HARDWARE
Connector X22
VGA 1 (15 pin D-Sub female connector)
Connector X23
IDE (40 pin male connector)
PIN
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
FUNCTION
R_OUT1
G_OUT1
B_OUT1
GND
GND
GND
GND
GND
N.C.
GND
GND
N.C.
HSYNC_OUT1
VSYNC_OUT1
N.C.
Connector X24
VGA 2 (15 pin D-Sub female connector)
PIN
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
FUNCTION
R_OUT2
G_OUT2
B_OUT2
GND
GND
GND
GND
GND
N.C.
GND
GND
N.C.
HSYNC_OUT2
VSYNC_OUT2
N.C.
PIN
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
FUNCTION
nD1RESET
GND
D1D7
D1D8
D1D6
D1D9
D1D5
D1D10
D1D4
D1D11
D1D3
D1D12
D1D2
D1D13
D1D1
D1D14
D1D0
D1D15
GND
N.C.
N.C.
GND
nD1IOWR
GND
nD1IORD
GND
D1IORDY
N.C.
N.C.
GND
D1INTRQ
nIOCS16
D1A3
N.C.
D1A2
D1A4
D1E_CS0
D1E_CS1
N.C.
GND
P a g e
159
HARDWARE
P a g e
160
PIN
A01
A02
A03
A04
A05
A06
A07
A08
A09
A10
A11
A12
A13
A14
A15
A16
A17
A18
A19
A20
A21
A22
A23
A24
A25
A26
A27
A28
A29
A30
A31
A32
FUNCTION
GND
GND
+5V-MB
OUT33
OUT36
GND
OUT37
OUT40
GND
+5V-MB
IN50
IN59
GND
IN54
IN63
GND
+5V-MB
OUT57
OUT60
GND
nPFI
nERID
GND
+5V-MB
nETXC
nECTSC
GND
nERXB
nEDSRB
nERTSB
GND
+5V-MB
PIN
B01
B02
B03
B04
B05
B06
B07
B08
B09
B10
B11
B12
B13
B14
B15
B16
B17
B18
B19
B20
B21
B22
B23
B24
B25
B26
B27
B28
B29
B30
B31
B32
FUNCTION
IN38
IN39
IN40
OUT34
OUT41
OUT43
OUT38
OUT45
OUT47
IN49
IN58
IN52
IN53
IN62
IN56
OUT49
OUT51
OUT58
OUT53
OUT55
INT_RES
nEDCDD
nECTSD
nERTSD
nERTSC
nEDSRC
nERIC
nERIB
nECTSB
nETXB
nERTSA
nECTSA
PIN
C01
C02
C03
C04
C05
C06
C07
C08
C09
C10
C11
C12
C13
C14
C15
C16
C17
C18
C19
C20
C21
C22
C23
C24
C25
C26
C27
C28
C29
C30
C31
C32
FUNCTION
IN46
IN47
IN48
OUT35
OUT42
OUT44
OUT39
OUT46
OUT48
IN57
IN51
IN60
IN61
IN55
IN64
OUT50
OUT52
OUT59
OUT54
OUT56
nERXD
nEDSRD
nEDTRD
nETXD
nEDTRC
nEDCDC
nERXC
nEDCDB
nEDTRB
nETXA
nEDTRA
nEDSRA
45M623N5UK-01
Connector X25
COOLFIRE motherboard (96 pin female connector)
HARDWARE
45M623N5UK-01
Connector X26
COOLFIRE motherboard (96 pin female connector)
PIN
A01
A02
A03
A04
A05
A06
A07
A08
A09
A10
A11
A12
A13
A14
A15
A16
A17
A18
A19
A20
A21
A22
A23
A24
A25
A26
A27
A28
A29
A30
A31
A32
FUNCTION
nEDCDA
GND
D1A3
GND
+5V-MB
GND
D1D0
GND
+5V-MB
GND
D1D10
D1D6
GND
+5V-MB
GND
ED5
+5V-MB
GND
EA6
GND
nI/O_RESET
GND
nECTS2
+5V-MB
RES_CTRL4
GND
GND
GND
GND
GND
GND
GND
PIN
B01
B02
B03
B04
B05
B06
B07
B08
B09
B10
B11
B12
B13
B14
B15
B16
B17
B18
B19
B20
B21
B22
B23
B24
B25
B26
B27
B28
B29
B30
B31
B32
FUNCTION
nERIA
D1E_CS1
D1A2
nIOCS16
nD1IORDY
nD1IOWR
D1D14
D1D13
D1D12
D1D11
D1D5
D1D8
nD1RESET
ED1
ED3
ED6
EA2
EA4
EA7
nIORD
nECTS1
ERXD1
ERXD2
nCS_RES1
RES_CRTL5
RES_OUT2
R_OUT2
G_OUT2
B_OUT2
R_OUT1
G_OUT1
B_OUT1
PIN
C01
C02
C03
C04
C05
C06
C07
C08
C09
C10
C11
C12
C13
C14
C15
C16
C17
C18
C19
C20
C21
C22
C23
C24
C25
C26
C27
C28
C29
C30
C31
C32
FUNCTION
nERXA
D1E_CSO
D1A4
D1INTR
nD1IORD
D1D15
D1D1
D1D2
D1D3
D1D4
D1D9
D1D7
ED0
ED2
ED4
ED7
EA3
EA5
EA8
nIOWR
nERTS1
ETXD1
ETXD2
RES_CTRL3
RES_CTRL6
RES_IN1
nCS_RES0
VSYNC_OUT2
HSYNC_OUT2
VSYNC_OUT1
HSYNC_OUT1
GND
P a g e
161
HARDWARE
Connector X27
Power expansion (6 pin Mini Fit Header)
Connector X32
Hopper 3 (16 pin Mini Fit Header)
FUNCTION
+12V DC
GND
+5V DC
+12V DC
GND
+5V DC
Connector X30
Hopper 1 (14 pin Mini Fit Header)
P a g e
162
PIN
01
02
03
04
05
06
07
08
09
10
11
12
13
14
FUNCTION
H1_M+
H1_M+12V DC
GND
HIGH LEVEL
LOW LEVEL
COIN OUT
N.C.
SECURITY
H1_INP1
H1_INP2
H1_INP3
+24V DC
PGND
PIN
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
FUNCTION
H3_M+
H3_M+12V DC
GND
HIGH LEVEL
LOW LEVEL
COIN OUT
N.C.
SECURITY
H3_INP1
H3_INP2
H3_INP3
+24V DC
PGND
+5V DC
N.C.
45M623N5UK-01
PIN
01
02
03
04
05
06
HARDWARE
45M623N5UK-01
Connector X31
Main wire loom (46 pin female connector)
PIN
A01
A02
A03
A04
A05
A06
A07
A08
A09
A10
A11
A12
A13
A14
A15
A16
A17
A18
A19
A20
A21
A22
A23
A24
A25
A26
A27
A28
A29
A30
A31
A32
FUNCTION
GND
GND
IN5
IN6
IN7
IN8
IN9
IN10
IN11
IN12
GND
GND
IN13
IN14
IN15
IN16
IN17
IN18
IN19
IN20
GND
GND
IN21
IN22
IN23
IN24
IN25
IN26
IN27
IN28
+5V DC
+5V DC
PIN
C01
C02
C03
C04
C05
C06
C07
C08
C09
C10
C11
C12
C13
C14
C15
C16
C17
C18
C19
C20
C21
C22
C23
C24
C25
C26
C27
C28
C29
C30
C31
C32
FUNCTION
+12V-L
+12V-L
L1
LL2
L3
L4
L5
L6
L7
L8
+12V-L
+12V-L
L9
L10
L11
L12
L13
L14
L15
L16
+12V-L
+12V-L
L17
L18
L19
L20
L21
L22
L23
L24
+5V DC
+5V DC
P a g e
163
HARDWARE
V.7.5
If any defects occur, check whether all connectors are fixed correctly on the COOLFIRE backplane.
V.7.6
Troubleshooting
If any defects of the COOLFIRE backplane cannot be repaired, the defective part has to be exchanged.
45M623N5UK-01
Backplanetausch.eps
P a g e
164
HARDWARE
V.8
Top light
V.8.2
Function
V.8.3
V.8.4
45M623N5UK-01
V.8.1
P a g e
165
45M623N5UK-01
HARDWARE
There are static-sensitive parts inside the machine which could be damaged by electric
discharge. Ground yourself by touching a ground strap inside the machine to neutralize
electric charges before changing or maintaining inner parts.
P a g e
166
HARDWARE
V.8.1
V.8.2
Function
The top light indicates the different status of operation (jackpot, error, service...).
V.8.3
45M623N5UK-01
F_Lichtturm.JpG
F_CS_LT_Schrauben.eps
P a g e
167
HARDWARE
V.8.4
F_CS_LT_Teile.jpg
P a g e
168
45M623N5UK-01
HARDWARE
V.9
Illumination
V.9.2
Key illumination
V.9.3
V.9.4
Lightbox illumination
45M623N5UK-01
V.9.1
P a g e
169
45M623N5UK-01
HARDWARE
There are static-sensitive parts inside the machine which could be damaged by electric
discharge. Ground yourself by touching a ground strap inside the machine to neutralize
electric charges before changing or maintaining inner parts.
P a g e
170
HARDWARE
V.9.1
V.9.1.2 Function
F_BNP_Bel.jpg
45M623N5UK-01
F_BNP_Beleuchtung.eps
P a g e
171
HARDWARE
The bill acceptor illumination is located on a circuit board inside the Main Door (see illustr. V.9.2).
45M623N5UK-01
1) Open the Main Door and disconnect the machine from the mains.
2) Disconnect the plug connections and remove the complete circuit board by unscrewing both nuts.
3) Exchange the unit, tighten the nuts and connect the cable connection with the circuit board.
P a g e
172
HARDWARE
V.9.2
Key illumination
V.9.2.2 Function
The key illumination shows the active buttons during game playing. If the machine is not equipped
with a touchscreen, the functions of the bookkeeping are activated via the respectively illuminated buttons.
F_BNP_Bel.jpg
45M623N5UK-01
P a g e
173
HARDWARE
V.9.3
V.9.3.2 Function
45M623N5UK-01
F_623_Lampen DiD_TIPR.jpg
The starter for the fluorescent tube is located inside the machine down left at the housing.
P a g e
174
HARDWARE
V.9.4
Lightbox illumination
V.9.4.2 Function
45M623N5UK-01
F_623_Lichtkasten_offen.jpg
F_623_Lichtkastenbeleuchtung.jpg
The starter for the fluorescent tube in the lightbox is located beside the fluorescent tube.
P a g e
175
45M623N5UK-01
HARDWARE
P a g e
176
HARDWARE
V.10
Mechanical meters
V.10.2
Function
V.10.3
Troubleshooting
V.10.4
45M623N5UK-01
V.10.1
P a g e
177
45M623N5UK-01
HARDWARE
There are static-sensitive parts inside the machine which could be damaged by electric
discharge. Ground yourself by touching a ground strap inside the machine to neutralize
electric charges before changing or maintaining inner parts.
P a g e
178
HARDWARE
V.10.2 Function
These mechanical meters represent the respective values of the machine accounting.
IN
OUT
BET
WIN
GAMES
REMOTE
HANDPAY
BILLS
45M623N5UK-01
Z_Zhlwerke.eps
IN
OUT
BET
WIN
GAMES
REMOTE
HANDPAY
BILLS
Total value of all coins and bills inserted and credits added via the remote function.
Total value of all credits paid out (hopper and handpay).
Total value of all bets in credits.
Total value of all wins in credits.
Total value of all games played.
Total value of all credits added via the remote function.
Total value of all credits paid out via handpay.
Total value of all bills inserted in credits.
V.10.3 Troubleshooting
P a g e
179
HARDWARE
F_623_Position Zaehlwerke.jpg
F_623_Zaehlwerktausch.jpg
45M623N5UK-01
1) Open the Main Door and disconnect the machine from the mains.
2) Unscrew the meter cover (see illustr. V.10.2).
3) Disconnect the main plug of the meters.
4) Unscrew the meter unit and exchange it.
5) Assemble the meter unit in reverse order.
P a g e
180
HARDWARE
V.11
Door optics/switches
V.11.2
Function
V.11.3
Troubleshooting
V.11.4
45M623N5UK-01
V.11.1
P a g e
181
45M623N5UK-01
HARDWARE
There are static-sensitive parts inside the machine which could be damaged by electric
discharge. Ground yourself by touching a ground strap inside the machine to neutralize
electric charges before changing or maintaining inner parts.
P a g e
182
HARDWARE
V.11.2 Function
The door optics/switches monitor the openings and closings of the machine doors.
V.11.3 Troubleshooting
45M623N5UK-01
F_Trschalter.eps
35500583.jpg
Illustr. V.11.1 Exchange of the door switch resp. the door switch board
P a g e
183
HARDWARE
receiver
transmitter
F_623CF_Tuersensor_Gehaeuse.jpg
F_623CF_Tuersensor_Tuer.jpg
45M623N5UK-01
1) Open the Main Door and disconnect the machine from the mains.
2) Release the hexagon screws and the connectors and exchange the defective board.
P a g e
184
HARDWARE
V.12
Loudspeakers
V.12.2
Volume control
V.12.3
Troubleshooting
45M623N5UK-01
V.12.1
P a g e
185
45M623N5UK-01
HARDWARE
There are static-sensitive parts inside the machine which could be damaged by electric
discharge. Ground yourself by touching a ground strap inside the machine to neutralize
electric charges before changing or maintaining inner parts.
P a g e
186
HARDWARE
Loudspeaker: 8 Ohm, 10 W
F_623CF_LS_MainDoor.jpg
F_623CF_Monitormaske.jpg
45M623N5UK-01
F_623CF_Lautstaerke.jpg
V.12.3 Troubleshooting
Loudspeaker left:
Loudspeaker rights:
If any defects of the loudspeakers cannot be repaired, exchange the defective part.
+ red/black
+ orange/green
- orange/black
- orange/black
P a g e
187
45M623N5UK-01
HARDWARE
P a g e
188
HARDWARE
45M623N5UK-01
V.13
Preventative maintenance
V.13.1
Bill acceptor
V.13.2
V.13.3
Door optics
V.13.4
Monitor / Touchscreen
V.13.5
Maintenance intervals
P a g e
189
45M623N5UK-01
HARDWARE
Before starting any maintenance work make sure, that the machine is disconnected from the mains by
pulling the power plug out of the socket.
The following service instructions are for use by qualified or trained personnel only.
To avoid personal injury or damage to the equipment, do not perform any servicing other
than such contained in this manual.
If you follow these instructions closely and the machine is maintained and handled in a proper way, it
complies with the usual safety standards.
Periodic cleaning prevents a lot of failures.
There are static-sensitive parts inside the machine which could be damaged by electric
discharge. Ground yourself by touching a ground strap inside the machine to neutralize
electric charges before changing or maintaining inner parts.
P a g e
190
HARDWARE
ATTENTION
To avoid excessive errors perform the cleaning procedures with recommended frequency.
Never use a water jet to clean the device!
reader sensors
45M623N5UK-01
magnetic sensor
reader sensors
F_WBA_Reinigung1.eps
F_WBA_Reinigung2.eps
Description:
If reader sensors or magnetic sensors are dirty this may result in error messages as when bills are jammed,
or the identification precision may increase, which may result in bills being rejected more frequently.
To clean the reader head / magnetic sensor use a soft cloth or cotton bud.
If necessary, a standard head cleaner for cassette recorder can be used.
ATTENTION
If bill acceptance does not improve after cleaning the sensors may require re-adjusting.
CLEANING
Cleaning towels for the WBA bill acceptor are available from AGI (Cleaning card kit).
P a g e
191
HARDWARE
45M623N5UK-01
Open the fixing screw of the coin optics board. Clean the optics with a short-hair brush or a cotton bud
and with isopropyl alcohol. Be careful not do bend the optics. Re-install the coin optics board.
F_Mnzprfer_ausgebaut.eps
F_Mnzkanallichtschranke.eps
ATTENTION
Do not use organic solvent like thinner! Do not use abrasive materials!
NOTE
Make sure that the sensors are adjusted properly and that there are no obstructions
in the optical transmission distance between the transmitter and the receiver.
P a g e
192
HARDWARE
Description:
If the machine has many errors of the Main Door, clean the door optics with a short-hair brush
or a cotton bud and with isopropyl alcohol.
To re-align the optics the fixing screws have to be loosened.
receiver
transmitter
45M623N5UK-01
F_623CF_Tuersensor_Gehaeuse.jpg
F_623CF_Tuersensor_Tuer.jpg
Description:
The touchscreen should be cleaned at least once a week using a soft cloth and window cleaner.
In addition, the touchscreen requires regular calibration, which will depend on how much it is
used but should at least be done once a week. When calibrating the touchscreen make sure that
you are looking at the screen straight from above (from the players seated position!) and are not
touching the metal cabinet of the terminal with your body.
P a g e
193
HARDWARE
Interval
Bill acceptor
Coin acceptor
Door optics
Reel light barrier
Lamps of the reel unit
Reel axis O-rings
Monitor / Touchscreen
Ticket printer EPIC 950 (print head)
monthly
3-monthly
semi-yearly
semi-yearly
semi-yearly
after 200.000 games played or after 3 years
weekly
3-monthly
45M623N5UK-01
P a g e
194
Annex
Table of Illustrations
45M623N5UK-01
Glossary
45M623N5UK-01
ANNEX
P a g e
196
ANNEX
45M623N5UK-01
Table of Illustrations
Illustr.
Illustr.
Illustr.
Illustr.
Illustr.
Illustr.
Illustr.
Illustr.
Illustr.
Illustr.
Illustr.
Illustr.
Illustr.
Illustr.
Illustr.
Illustr.
Illustr.
Illustr.
Illustr.
Illustr.
Illustr.
Illustr.
Illustr.
Illustr.
Illustr.
Illustr.
Illustr.
Illustr.
Illustr.
Illustr.
Illustr.
Illustr.
Illustr.
Illustr.
Illustr.
Illustr.
Illustr.
Illustr.
Illustr.
Illustr.
Illustr.
Illustr.
Illustr.
0.1
I.1.1
I.2.1
I.3.1
II.2.1
II.2.2
III.1.1
III.2.1
IV.1.1
IV.1.2
IV.1.3
IV.9.1
V.0.1
V.0.2
V.1.1
V.2.1
V.2.2
V.2.3
V.2.4
V.2.5
V.2.6
V.2.7
V.2.8
V.2.9
V.2.10
V.3.1
V.3.2
V.3.3
V.3.4
V.4.1
V.5.1
V.5.2
V.5.3
V.6.1
V.6.2
V.6.3
V.6.4
V.6.5
V.7.1
V.7.2
V.8.1
V.8.2
V.8.3
ID Plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Operating elements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Description of components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Machine dimensions FV-623 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Drilling jig . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Drilling scheme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Main switch with fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Error display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Attendant keyswitch for error handling . . . . . . . . . . . . . . . . . . . . . . . . 27
Internal error - Screenshot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Error message - Explanation of elements . . . . . . . . . . . . . . . . . . . . . . 28
Position OF DIP switch 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
Description of components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
Switching power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
Lock bar of the bill acceptor WBA-25-SS2 . . . . . . . . . . . . . . . . . . . . . 121
Bill acceptor Cashflow SC83 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
Exchange of the bill acceptor Cashflow SC83 . . . . . . . . . . . . . . . . . . . 122
Components Cashflow SC83 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122
Components WBA-25-SS2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122
Collecting bills - WBA-25-SS2 . . . . . . . . . . . . . . . . . . . . . . . . . . . 123
Collecting bills - Cashflow SC83 . . . . . . . . . . . . . . . . . . . . . . . . . . 123
Removing jammed bills - WBA-25-SS2 . . . . . . . . . . . . . . . . . . . . . . . 124
Removing jammed bills - Cashflow SC83 . . . . . . . . . . . . . . . . . . . . . 124
Acceptor unit of the bill acceptor . . . . . . . . . . . . . . . . . . . . . . . . . . 125
Exchange of the coin acceptor NRI-G13 . . . . . . . . . . . . . . . . . . . . . . 130
Exchange of the coin comparitor MC-40 . . . . . . . . . . . . . . . . . . . . . . 130
Programming of the coin acceptor NRI-G13 . . . . . . . . . . . . . . . . . . . . 131
DIL switch on coin acceptor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133
Exchange of the hopper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137
Exchange of the lower monitor (FV-623) . . . . . . . . . . . . . . . . . . . . . . 141
Exchange of the upper monitor (FV-623) . . . . . . . . . . . . . . . . . . . . . . 142
Buttons for adjustment of the screen . . . . . . . . . . . . . . . . . . . . . . . . 143
Exchange of the mainboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147
DIP switch position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148
Position game selector (1), game software (2), EEPROM (3) . . . . . . . . . . . 149
Exchange of the game software . . . . . . . . . . . . . . . . . . . . . . . . . . 150
Correct insertion position of the EEPROM . . . . . . . . . . . . . . . . . . . . . 150
Pin assignment COOLFIRE backplane . . . . . . . . . . . . . . . . . . . . . . . 153
Exchange of the COOLFIRE Backplane . . . . . . . . . . . . . . . . . . . . . . 164
Top light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 167
Fixing screw of the top light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 167
Components of the top light . . . . . . . . . . . . . . . . . . . . . . . . . . . . 168
Page 197
ANNEX
V.9.1
V.9.2
V.9.3
V.9.4
V.9.5
V.9.6
V.10.1
V.10.2
V.11.1
V.11.2
V.12.1
V.12.2
V.12.3
V.13.1
V.13.2
V.13.3
V.13.4
V.13.5
45M623N5UK-01
Illustr.
Illustr.
Illustr.
Illustr.
Illustr.
Illustr.
Illustr.
Illustr.
Illustr.
Illustr.
Illustr.
Illustr.
Illustr.
Illustr.
Illustr.
Illustr.
Illustr.
Illustr.
Page 198
ANNEX
Glossary
Bill acceptor
Bill acceptor channel
The bill acceptor has various software channels, which are used for
recognition of different bills. Each channel is programmed for a single
type of bill.
Booksize PC
45M623N5UK-01
Calibration
Cancel Credit
Coin channel
The coin acceptor has various software channels, which are used for
recognition of different coins. Each channel is programmed for a single
type of coin.
DIP/DIL switch
Dongle
Gamble Function
Grounding strap
Handpay
Hopper
P a g e
199
ANNEX
Jackpot
Keycode
LED
Mechanical meters
Pin
Push up
Connector, plug.
45M623N5UK-01
Reference coin
Remote
Reset
ROM
Abr. for: Read Only Memory; A type of memory that can be read but not
written in normal operation. Special techniques are required to initialize
the contents of a ROM, which are usually considered permanent and is
powered by a small long-life battery.
P a g e
200
ANNEX
Sorter
Stand-by
Test switch
Used for calling the Test Menu. The test switch is located inside the
machine.
TFT
Ticket printer
Printing unit, used for printing credit tickets, which can be used to cash
wins or for moneyless payout purposes.
45M623N5UK-01
Token
Touchscreen
Zapper error
Suspicion of manipulation.
P a g e
201
45M623N5UK-01
ANNEX
P a g e
202
FEEDBACK FORM
Please spare some minutes of your time to answer the following questions as precisely as possible
and send the form back to us.
You can reach us
by phone under +43 2252 606 300,
by fax under +43 2252 607 001. You can also
send us an E-mail to support@novomatic.com.
1.) Were you satisfied with the execution of the order?
If NO, please indicate why.
2.)
NO
c
45M623N5UK-01
3.)
YES
c
4.)
5.)
6.)
7.)
Page 203
FEEDBACK FORM
8.) Do you think that the machine is user-optimized?
If NO, please indicate suggestions for improvement?
YES
c
NO
c
45M623N5UK-01
9.)
Remitter:
Thank you!
P a g e
204
ELEK38010094-3.xls / Plug-Pinning
colour
Farbe
qmm
01a
01c
02a
02c
03a
03c
04a
04c
05a
05c
06a
06c
07a
07c
08a
08c
09a
09c
10a
10c
11a
11c
12a
12c
13a
13c
14a
14c
15a
15c
16a
16c
17a
17c
18a
18c
19a
19c
20a
20c
21a
21c
22a
22c
23a
23c
24a
24c
red
red
nc
nc
nc
nc
violet/brown
white/violet
white/orange
yellow/blue
white/black
red/blue
brown/black
grey/black
pink/blue
grey
green/black
grey/violet
pink
white/blue
orange/black
yellow
orange/black
yellow
blue/black
brown/blue
orange/brown
pink/brown
grey/green
yellow/violet
blue/violet
pink/grey
white/yellow
white/red
yellow/red
violet/black
yellow/pink
pink/orange
pink/black
red/black
rot
rot
nc
nc
nc
nc
violett/braun
wei/violett
wei/orange
gelb/blau
wei/schwarz
rot/blau
braun/schwarz
grau/schwarz
rosa/blau
grau
grn/schwarz
grau/violett
rosa
wei/blau
orange/schwarz
gelb
orange/schwarz
gelb
blau/schwarz
braun/blau
orange/braun
rosa/braun
grau/grn
gelb/violett
blau/violett
rosa/grau
wei/gelb
wei/rot
gelb/rot
violett/schwarz
gelb/rosa
rosa/orange
rosa/schwarz
rot/schwarz
orange/black
orange/schwarz
nc
nc
orange/black
orange/schwarz
nc
brown/grey
nc
green /brown
nc
nc
braun/grau
nc
grn/braun
nc
0.35
0.35
***
***
***
***
0.35
0.35
0.50
0.35
0.50
0.35
0.50
0.35
0.35
0.35
0.35
0.35
0.35
0.35
0.5
0.5
0.35
0.5
0.35
0.35
0.35
0.35
0.35
0.35
0.35
0.35
0.35
0.35
0.35
0.5
0.35
0.5
0.35
0.5
0.35
***
0.5
***
0.35
***
0.35
***
AGI
2352 Gumpoldskirchen
Wiener Strae 158
Funktion
+5VDC fr OP-S
+5VDC fr OP-R
***
***
***
***
RESERVE
RESERVE
Schlsselschalter 3 (TEST)
PLAY 7 LINES
Schlsselschalter 2 (AUDIT)
PLAY 5 LINES
Schlsselschalter 1 (ATTENDANT)
Funktion-allg.
Treiber
kurz. Bezeichnung
VCC +5VDC
VCC +5VDC
VCC +5VDC
VCC +5VDC
INPUT 28
OUTPUT 24
INPUT 27
OUTPUT 23
INPUT 26
OUTPUT 22
INPUT 25
OUTPUT 21
INPUT 24
OUTPUT 20
INPUT 23
OUTPUT 19
INPUT 22
OUTPUT 18
INPUT 21
OUTPUT 17
GND
+12VDC
GND
+12VDC
INPUT 20
OUTPUT 16
INPUT 19
OUTPUT 15
INPUT 18
OUTPUT 14
INPUT 17
OUTPUT 13
INPUT 16
OUTPUT 12
INPUT 15
OUTPUT 11
INPUT 14
OUTPUT 10
INPUT 13
OUTPUT 9
GND
+12VDC
GND
+12VDC
INPUT 12
OUTPUT 8
INPUT 11
OUTPUT 7
***
***
***
***
***
***
***
***
***
S22
H22
S21
H21
KEY3
H06
KEY2
H05
KEY1
H04
ST02
H03
S18
H02
S17
H01
***
***
***
***
S16
H15
S15
H14
S14
H13
S13
ST04
S12
ST03
S11
H20
S10
H19
S09
H18
***
***
***
***
S08
***
S07
***
ULN2064
ULN2064
ULN2064
ULN2064
ULN2064
ULN2064
ULN2064
ULN2064
***
***
***
***
***
ULN2803
***
ULN2803
ULN2803
ULN2803
ULN2803
ULN2803
ULN2803
ULN2803
***
***
***
***
***
ULN2803
ULN2803
ELEK38010094-3.xls / Plug-Pinning
25a
25c
26a
26c
27a
27c
28a
28c
29a
29c
30a
30c
31a
31c
32a
32c
yellow/brown
white/grey
red/brown
red/grey
yellow/black
orange/violet
red/violet
white/brown
yellow/grey
blue/grey
pink/violet
blue/green
orange/black
yellow
orange/black
yellow
gelb/braun
wei/grau
rot/braun
rot/grau
gelb/schwarz
orange/violett
rot/violett
wei/braun
gelb/grau
blau/grau
rosa/violett
blau/grn
orange/schwarz
gelb
orange/schwarz
gelb
0.35
0.35
0.35
0.35
0.35
0.35
0.35
0.35
0.35
0.35
0.35
0.35
0.5
0.5
0.5
0.5
PLAY 7 LINES
START
PLAY 5 PER LINE
TAKE WIN
BET 2 PER LINE
GAMBLE
PLAY 3 PER LINES
BET 10 PER LINES
BET 1 PER LINE
BET 5 PER LINE
PLAY 1 LINE
BET 3 PER LINE
GND fr Tasten
+12VDC fr Lampen
GND fr Tasten
+12VDC fr Lampen
INPUT 10
OUTPUT 6
INPUT 9
OUTPUT 5
INPUT 8
OUTPUT 4
INPUT 7
OUTPUT 3
INPUT 6
OUTPUT 2
INPUT 5
OUTPUT 1
GND
+12VDC
GND
+12VDC
***
***
***
***
S06
H12
S05
H11
S04
H10
S03
H09
S02
H08
S01
H07
GND
+12VDC
GND
+12VDC
Funktion-allg.
Treiber
kurz. Bezeichnung
***
***
***
***
***
***
***
***
+5VDC
OP-R
GND
***
Funktion-allg.
Treiber
kurz. Bezeichnung
***
***
***
***
***
***
***
***
***
START
GND
+12VDC
Funktion-allg.
Treiber
kurz. Bezeichnung
***
***
***
***
***
***
***
***
+5VDC
OP-S
***
***
ULN2803
ULN2803
ULN2803
ULN2803
ULN2803
ULN2803
colour
Farbe
red
rot
pink/blue
rosa/blau
orange/black orange/schwarz
nc
nc
qmm
Funktion
0.35
0.35
0.35
+5VDC
doorswitch (receiver)
GND
***
(Anschlu an Hebeleinheit)
Stecker 03: 4pol. MINI-FIT Buchsengehuse Art.Nr:13100026 (Molex Nr:39-01-2040)
Pin
01
02
03
04
colour
Farbe
white/red
wei/rot
white/yellow
wei/gelb
orange/black orange/schwarz
yellow
gelb
qmm
0.35
0.35
0.35
0.5
Funktion
enable lever (Freigabe)
S12 (START)
GND
+12VDC
colour
Farbe
qmm
01
02
03
04
red
pink/grey
nc
nc
rot
rosa/grau
nc
nc
0.35
0.35
AGI
2352 Gumpoldskirchen
Wiener Strae 158
Funktion
+5VDC
doorswitch (transmitter diode)
***
***
ELEK38010094-3.xls / Plug-Pinning
(Walzenversorgung)
Stecker 05: 6pol. Mini-Fit Buchsengehuse; Art.Nr:13100029 (Molex 39-01-2060)
Pin
colour
Farbe
qmm
01
02
03
04
05
06
green
black
yellow
black
white
black
grn
schwarz
gelb
schwarz
wei
schwarz
1.0
1.0
1.0
1.0
1.0
1.0
Funktion
+24VDC(S)
GND(S)
+12VDC(S)
GND(S)
+12VDC(R)
GND(R)
Funktion-allg.
Treiber
kurz. Bezeichnung
***
***
***
***
***
***
***
***
***
***
***
***
Funktion-allg.
Treiber
kurz. Bezeichnung
***
***
***
***
***
***
Funktion-allg.
Treiber
kurz. Bezeichnung
***
***
***
***
***
***
***
***
+12VDC
H19
H18
H20
Funktion-allg.
Treiber
kurz. Bezeichnung
***
***
***
***
***
***
***
***
***
***
***
***
***
***
***
***
***
***
***
***
***
***
***
***
***
***
***
***
***
***
***
***
***
***
***
***
+5VDC
+5VDC
+5VDC
GND
GND
+12VDC
+12VDC
+12VDC
+24VDC
+5VDC
+5VDC
GND
GND
-12VDC
(Option +12VDC)
(Option +12VDC)
PFD
+24VDC
+24VDC(S)
GND(S)
+12VDC(S)
GND(S)
+12VDC(R)
GND(R)
(Touchscreen)
Stecker 06: 2pol. Molex Stiftgehuse; Art.Nr:13050002 (Molex 03-09-2021)
Pin
colour
Farbe
qmm
01
02
black
yellow
schwarz
gelb
1.0
1.0
Funktion
GND
+12VDC
(Toplightstecker)
Stecker 07: 4pol MOLEX Buchsengehuse; Art.Nr: 13100002 (Molex Nr:03-09-1040)
Pin
01
02
03
04
colour
Farbe
yellow
gelb
pink/orange
rosa/orange
red/black
rot/schwarz
violet/black violett/schwarz
qmm
0.5
0.5
0.5
0.5
Funktion
+12VDC
toplight (blau)
toplight (wei)
toplight (reserve)
(=rot)
(=gelb)
(=grn)
(Anschlu am NFS-Adapter-NGC)
Stecker 08: 18pol MOLEX Mini-Fit Stiftgehuse; Art.Nr:13100036 (Molex Nr:39-01-2181)
Pin
colour
Farbe
qmm
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
red
red
red
black
black
yellow
yellow
yellow
green
red
red
black
black
violet
nc
nc
orange
green
rot
rot
rot
schwarz
schwarz
gelb
gelb
gelb
grn
rot
rot
schwarz
schwarz
violett
nc
nc
orange
grn
1.0
1.0
0.5
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
***
***
0.5
1.0
AGI
2352 Gumpoldskirchen
Wiener Strae 158
Funktion
+5VDC
+5VDC
+5VDC
GND (Ringkern - NFS)
GND (Sternpunkt)
+12VDC (fr Backplane)
+12VDC (fr Sternpunkt)
+12VDC (fr Backplane)
+24VDC (fr Sternpunkt)
+5VDC
+5VDC
GND (fr Backplane)
GND (fr Backplane)
-12VDC
***
***
PFD
+24VDC (fr Backplane)
ELEK38010094-3.xls / Plug-Pinning
(Anschlu am Modularnetzteil)
Stecker 09: 6pol MOLEX Buchsengehuse Mini-Fit; Art.Nr: 13100029 (Molex Nr:39-01-2060)
Pin
colour
Farbe
qmm
01
02
03
04
05
06
white
white
white
black
black
black
wei
wei
wei
schwarz
schwarz
schwarz
1.0
1.0
1.0
1.0
1.0
0.5
Funktion
Funktion-allg.
Treiber
kurz. Bezeichnung
***
***
***
***
***
***
***
***
***
***
***
***
+12VDC
+12VDC
+12VDC
GND
GND
GND
Funktion-allg.
Treiber
kurz. Bezeichnung
***
***
+12VDC
Funktion-allg.
Treiber
kurz. Bezeichnung
***
***
***
***
***
***
***
***
***
***
***
***
***
***
***
***
***
***
***
***
***
***
***
***
+5VDC
GND
+12VDC
GND
+24VDC
GND
+5VDC
nc
+12VDC
nc
PFD
-12VDC
Funktion-allg.
Treiber
kurz. Bezeichnung
***
***
***
***
+12VDC
nc
Funktion-allg.
Treiber
kurz. Bezeichnung
***
***
***
***
***
***
***
***
audio-rechts
audio-GND
audio-links
audio-GND
+12VDC
+12VDC (Sternpunkt)
+12VDC
GND
GND
GND
colour
Farbe
qmm
white
wei
1.0
Funktion
+12VDC
colour
Farbe
qmm
01
02
03
04
05
06
07
08
09
10
11
12
red
black
white
black
green
black
red
nc
yellow
nc
orange
violet
rot
schwarz
wei
schwarz
grn
schwarz
rot
nc
gelb
nc
orange
violett
1.0
1.0
1.0
1.0
1.0
1.0
1.0
***
1.0
***
0.5
1.0
Funktion
+5VDC
GND
+12VDC (Trafo)
GND
+24VDC
GND
+5VDC
nc
+12VDC
nc
PFD
-12VDC
colour
Farbe
qmm
01
02
yellow
nc
gelb
nc
1.0
***
Funktion
+12VDC
nc
colour
Farbe
red/black
rot/schwarz
orange/black orange/schwarz
orange/green orange/grn
orange/black orange/schwarz
AGI
2352 Gumpoldskirchen
Wiener Strae 158
qmm
0.35
0.35
0.35
0.35
Funktion
audio-rechts
GND
audio-links
GND
ELEK38010094-3.xls / Plug-Pinning
(Anschlu an Zhlwerke)
Stecker 15: 15pol Sub-D Buchsengehuse; Art.Nr: 13600092 (AMP 164532-4)
Pin
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
colour
Farbe
red/green
rot/grn
pink/green
rosa/grn
green
grn
yellow/violet gelb/violett
blue/violet
blau/violett
brown/violet braun/violett
pink/orange
rosa/orange
green/grey
grn/grau
red/black
rot/schwarz
orange/black orange/schwarz
orange/black orange/schwarz
blue
blau
orange/red
orange/rot
yellow
gelb
yellow
gelb
qmm
Funktion
Funktion-allg.
Treiber
kurz. Bezeichnung
0.35
0.35
0.35
0.35
0.35
0.35
0.35
0.35
0.35
0.35
0.35
0.35
0.35
0.35
0.35
meter 1
meter 2
meter 3
meter 4
meter 5
meter 6
lamps on
metercount
m-security
GND
GND
meter 7
meter 8
+12VDC
+12VDC
***
***
***
***
***
***
***
***
***
***
***
***
***
***
***
***
***
***
***
***
***
***
***
***
***
***
***
***
***
***
meter 1
meter 2
meter 3
meter 4
meter 5
meter 6
lamps on
metercount
m-security
GND
GND
meter 7
meter 8
+12VDC
+12VDC
Funktion-allg.
Treiber
kurz. Bezeichnung
***
***
***
***
***
***
***
***
***
***
***
***
***
***
GND
***
Tilt
credit output
***
+12VDC
enable
Funktion-allg.
Treiber
kurz. Bezeichnung
***
***
***
***
***
***
***
***
Funktion-allg.
Treiber
***
***
***
***
***
***
(Anschlu an CC-46)
Stecker 16: 7pol Buchsengehuse RM2.54; Art.Nr: 13100073 (Molex 22-01-2075)
Pin
colour
Farbe
qmm
01
02
03
04
05
06
07
black
nc
orange
blue
nc
yellow
violet
schwarz
nc
orange
blau
nc
gelb
violett
0.35
***
0.35
0.35
***
0.35
0.35
Funktion
GND
***
Tilt
credit output
***
+12VDC
enable
(Anschlu an WBA-Statusanzeige)
Stecker 17: 4pol Buchsengehuse RM2.54; Art.Nr: 13100014 (Molex 22-01-2045)
Pin
colour
Farbe
qmm
01
02
03
04
yellow
pink
blue
violet
gelb
rosa
blau
violett
0.35
0.35
0.35
0.35
Funktion
+12VDC
LED A (rot)
LED B (grn)
LED C (gelb)
+12VDC
LED A (rot)
LED B (grn)
LED C (gelb)
colour
Farbe
qmm
01
02
03
black
pink/grey
yellow
schwarz
rosa/grau
gelb
0.35
0.35
0.35
AGI
2352 Gumpoldskirchen
Wiener Strae 158
Funktion
GND
Signal A
+12VDC
kurz. Bezeichnung
GND
Signal A
+12VDC
ELEK38010094-3.xls / Plug-Pinning
(Anschlu an Mnzkanallichtschranke 2 [unten])
Stecker 19: 3pol Buchsengehuse RM2.54; Art.Nr: 13100066 (Molex 22-01-2035)
Pin
colour
Farbe
qmm
01
02
03
black
white/violet
yellow
schwarz
wei/violett
gelb
0.35
0.35
0.35
Funktion
Funktion-allg.
Treiber
***
***
***
***
***
***
GND
Signal B
+12VDC
kurz. Bezeichnung
GND
Signal B
+12VDC
(Anschlu an Mnzweiche)
Stecker 20: 2pol. Molex Buchsengehuse Mini-Fit; Art.Nr:13100053 (Molex 39-01-2020)
Pin
colour
Farbe
qmm
01
02
yellow
red/violet
gelb
rot/violett
0.35
0.35
Funktion
Funktion-allg.
Treiber
kurz. Bezeichnung
***
***
***
+12VDC
CCHS1
Funktion-allg.
Treiber
kurz. Bezeichnung
***
***
***
***
***
***
Funktion-allg.
Treiber
***
***
***
***
***
***
***
***
***
***
Funktion-allg.
Treiber
***
***
***
***
***
***
***
***
+12VDC
CCHS1
colour
Farbe
qmm
01
02
03
red/violet
nc
yellow
rot/violett
nc
gelb
0.35
***
0.35
Funktion
CCHS1
nc
+12VDC
CCHS1
nc
+12VDC
colour
Farbe
qmm
01
02
03
04
05
yellow
black
pink/grey
white/violet
nc
gelb
schwarz
rosa/grau
wei/violett
nc
0.35
0.35
0.35
0.35
***
Funktion
+12VDC
GND
Signal A
Signal B
nc
kurz. Bezeichnung
+12VDC
GND
Signal A
Signal B
***
colour
Farbe
qmm
01
02
03
04
yellow
pink
blue
violet
gelb
rosa
blau
violett
0.35
0.35
0.35
0.35
AGI
2352 Gumpoldskirchen
Wiener Strae 158
Funktion
+12VDC
LED A (rot)
LED B (grn)
LED C (gelb)
kurz. Bezeichnung
+12VDC
LED A (rot)
LED B (grn)
LED C (gelb)
ELEK38010094-3.xls / Plug-Pinning
(Anschlu an Backplane, CC-46 [X8])
Stecker 24: 8pol Buchsengehuse RM2.54 Art.Nr: 13100044 (Molex 22-01-2085)
Pin
colour
Farbe
qmm
01
02
03
04
05
06
07
08
orange
nc
blue
black
yellow
violet
nc
nc
orange
nc
blau
schwarz
gelb
violett
nc
nc
0.35
***
0.35
0.35
0.35
0.35
***
***
Funktion
Funktion-allg.
Treiber
kurz. Bezeichnung
***
***
***
***
***
***
***
***
***
***
***
***
***
***
***
***
Tilt
***
credit output
GND
+12VDC
enable
***
***
Tilt
***
credit output
GND
+12VDC
enable
***
***
colour
Farbe
red/green
rot/grn
pink/green
rosa/grn
green
grn
yellow/violet gelb/violett
blue/violet
blau/violett
brown/violet braun/violett
pink/orange
rosa/orange
green/grey
grn/grau
red/black
rot/schwarz
orange/black orange/schwarz
orange/black orange/schwarz
blue
blau
orange/red
orange/rot
yellow
gelb
yellow
gelb
qmm
Funktion
Funktion-allg.
Treiber
kurz. Bezeichnung
0.35
0.35
0.35
0.35
0.35
0.35
0.35
0.35
0.35
0.35
0.35
0.35
0.35
0.35
0.35
meter 1
meter 2
meter 3
meter 4
meter 5
meter 6
lamps on
metercount
m-security
GND
GND
meter 7
meter 8
+12VDC
+12VDC
***
***
***
***
***
***
***
***
***
***
***
***
***
***
***
***
***
***
***
***
***
***
***
***
***
***
***
***
***
***
meter 1
meter 2
meter 3
meter 4
meter 5
meter 6
lamps on
metercount
m-security
GND
GND
meter 7
meter 8
+12VDC
+12VDC
colour
Farbe
pink
rosa
orange/black orange/schwarz
qmm
Funktion
Funktion-allg.
Treiber
kurz. Bezeichnung
0.35
0.35
S17
GND
***
***
***
***
S17
GND
Funktion
Funktion-allg.
Treiber
kurz. Bezeichnung
***
***
***
***
***
***
***
***
GND
serielle Verbindung
serielle Verbindung
GND
colour
Farbe
qmm
01
02
03
04
yellow
green
brown
white
gelb
grn
braun
wei
AWG26
AWG26
AWG26
AWG26
AGI
2352 Gumpoldskirchen
Wiener Strae 158
***
***
***
***
ELEK38010094-3.xls / Plug-Pinning
(Anschlu am Platine P422)
Stecker 29: 4pol Tel. Modulstecker; Art.Nr: 13800031
Pin
colour
Farbe
qmm
01
02
03
04
yellow
green
brown
white
gelb
grn
braun
wei
AWG26
AWG26
AWG26
AWG26
Funktion
***
***
***
***
Funktion-allg.
Treiber
kurz. Bezeichnung
***
***
***
***
***
***
***
***
GND
serielle Verbindung
serielle Verbindung
GND
colour
Farbe
qmm
Funktion
Funktion-allg.
Treiber
kurz. Bezeichnung
01
02
03
04
05
06
07
08
09
10
red
grey
grey
grey
grey
grey
grey
grey
grey
grey
rot
grau
grau
grau
grau
grau
grau
grau
grau
grau
AWG28/7
AWG28/7
AWG28/7
AWG28/7
AWG28/7
AWG28/7
AWG28/7
AWG28/7
AWG28/7
AWG28/7
Flachbandkabel RM1.27
Flachbandkabel RM1.27
Flachbandkabel RM1.27
Flachbandkabel RM1.27
Flachbandkabel RM1.27
Flachbandkabel RM1.27
Flachbandkabel RM1.27
Flachbandkabel RM1.27
Flachbandkabel RM1.27
Flachbandkabel RM1.27
GND
+12VDC
Channel 5
Channel 6
Reject
ENABLE
Channal 1
Channal 2
Channal 3
Channal 4
***
***
***
***
***
***
***
***
***
***
***
***
***
***
***
***
***
***
***
***
(Anschlu am NRI)
Stecker 31: 10pol Pfostenverbinder, schneidklemm Art.Nr: 13300001 (Harting 09 18 510 7803)
Pin
colour
Farbe
qmm
Funktion
Funktion-allg.
Treiber
kurz. Bezeichnung
01
02
03
04
05
06
07
08
09
10
red
grey
grey
grey
grey
grey
grey
grey
grey
grey
rot
grau
grau
grau
grau
grau
grau
grau
grau
grau
AWG28/7
AWG28/7
AWG28/7
AWG28/7
AWG28/7
AWG28/7
AWG28/7
AWG28/7
AWG28/7
AWG28/7
Flachbandkabel RM1.27
Flachbandkabel RM1.27
Flachbandkabel RM1.27
Flachbandkabel RM1.27
Flachbandkabel RM1.27
Flachbandkabel RM1.27
Flachbandkabel RM1.27
Flachbandkabel RM1.27
Flachbandkabel RM1.27
Flachbandkabel RM1.27
GND
+12VDC
Channel 5
Channel 6
Reject
ENABLE
Channal 1
Channal 2
Channal 3
Channal 4
***
***
***
***
***
***
***
***
***
***
***
***
***
***
***
***
***
***
***
***
Funktion-allg.
Treiber
kurz. Bezeichnung
***
***
***
***
***
***
***
***
***
***
***
***
colour
Farbe
qmm
01
02
03
04
05
06
black
black
red
yellow
yellow
green
schwarz
schwarz
rot
gelb
gelb
grn
1.0
1.0
1.0
1.0
1.0
1.0
AGI
2352 Gumpoldskirchen
Wiener Strae 158
Funktion
GND(S)
GND(S)
+5VDC(S)
+12VDC(S)
+12VDC(S)
+24VDC(S)
GND(S)
GND(S)
+5VDC(S)
+12VDC(S)
+12VDC(S)
+24VDC(S)
ELEK38010094-3.xls / Plug-Pinning
(Anschlu an P422)
Stecker 33: 4pol MOLEX Buchsengehuse Mini-Fit; Art.Nr: 13100026 (Molex Nr:39-01-2040)
Pin
01
02
03
04
colour
Farbe
black
schwarz
orange/black orange/schwarz
red
rot
yellow
gelb
qmm
0.5
0.5
0.5
1.0
Funktion
Funktion-allg.
Treiber
kurz. Bezeichnung
***
***
***
***
***
***
***
***
GND(T)
GND(S)
+5VDC(S)
+12VDC(S)
Funktion-allg.
Treiber
kurz. Bezeichnung
***
***
+12VDC
Funktion-allg.
Treiber
kurz. Bezeichnung
***
***
***
***
***
***
***
***
***
***
***
***
***
***
***
***
***
***
***
***
***
***
***
***
+5VDC
GND
***
GND
+24VDC
***
***
GND
***
***
***
***
GND(T)
GND(S)
+5VDC(S)
+12VDC
colour
Farbe
qmm
white
wei
1.0
Funktion
+12VDC
colour
Farbe
qmm
01
02
03
04
05
06
07
08
09
10
11
12
red
black
nc
black
green
nc
nc
black
nc
nc
nc
nc
rot
schwarz
nc
schwarz
grn
nc
nc
schwarz
nc
nc
nc
nc
1.0
1.0
***
1.0
1.0
***
***
1.0
***
***
***
***
Funktion
+5VDC
GND
nc
GND
+24VDC
nc
nc
GND
nc
nc
nc
nc
colour
Farbe
qmm
Funktion
Funktion-allg.
Treiber
kurz. Bezeichnung
01
02
green
black
grn
schwarz
1.0
1.0
+24VDC
GND
***
***
***
***
+24VDC
GND
Funktion-allg.
Treiber
kurz. Bezeichnung
***
***
***
***
***
***
***
***
colour
Farbe
qmm
01
02
03
04
nc
nc
green
black
nc
nc
grn
schwarz
***
***
0.35
0.35
AGI
2352 Gumpoldskirchen
Wiener Strae 158
Funktion
nc
nc
+24VDC
GND
***
***
+24VDC
GND
ELEK38010094-3.xls / Plug-Pinning
Stecker 39: 2pol Mini-Fit Buchsengehuse Art.Nr: 13100053 (Molex 39-01-2020)
(Stecker fr Topper-Versorgung +12VDC )
Pin
colour
Farbe
qmm
Funktion
Funktion-allg.
Treiber
kurz. Bezeichnung
01
02
black
yellow
schwarz
gelb
0.5
0.5
GND
+12VDC
***
***
***
***
GND
+12VDC
colour
Farbe
NO brown/black braun/schwarz
C orange/black orange/schwarz
qmm
Funktion
Funktion-allg.
Treiber
kurz. Bezeichnung
0.5
0.5
Attendant Switch
GND
***
***
***
***
KEY 01
GND
colour
Farbe
NO white/black wei/schwarz
C orange/black orange/schwarz
qmm
Funktion
Funktion-allg.
Treiber
kurz. Bezeichnung
0.5
0.5
Auditor Switch
GND
***
***
***
***
KEY 02
GND
colour
Farbe
NO white/orange wei/orange
C orange/black orange/schwarz
AGI
2352 Gumpoldskirchen
Wiener Strae 158
qmm
Funktion
Funktion-allg.
Treiber
kurz. Bezeichnung
0.5
0.5
Test Switch
GND
***
***
***
***
KEY 03
GND
ELEK38010094-3.xls / Plug-Description
(Walzenversorgung)
Stecker 06: 2pol. MOLEX Stiftgehuse; Art.Nr:13050002 (Molex 03-09-2021)
(Touchscreen)
Stecker 07: 4pol MOLEX Buchsengehuse; Art.Nr: 13100002 (Molex Nr:03-09-1040)
(Anschlu an Toplightstecker)
Stecker 08: 18pol Molex Mini-Fit Stiftgehuse; Art.Nr:13100036 (Molex 39-01-2181)
(Anschlu an Adapter NFS-Netzteil)
Stecker 09: 6pol MOLEX Buchsengehuse Mini-Fit; Art.Nr: 13100029 (Molex 39-01-2060)
(Anschlu am Modularnetzteil)
Stecker 11: 6.3mm Flachstecker
6.3mm Flachstecker: AMP 5-160 432-3 oder Seno
Steckhlsengehuse fr 6.3mm: AMP 926539-1 oder Seno
(Anschlu an Display bei Walzenmaschinen)
Art.Nr. 13800004
Art.Nr. 21000007
Stecker 12: 12pol MOLEX Buchsengehuse Mini-Fit; Art.Nr: 13100032 (Molex 39-01-2120)
(Anschlu an Backplane) [X11]
Stecker 13: 2pol MOLEX Buchsengehuse Mini-Fit; Art.Nr: 13100053 (Molex 39-01-2020)
(Optionaler Anschlu fr ST12/Pin03)
Stecker 14: 4pol MOLEX Buchsengehuse Mini-Fit; Art.Nr: 13100026 (Molex 39-01-2040)
(Anschlu an Backplane, Lautsprecher [X16])
Stecker 15: 15pol Sub-D Buchsengehuse; Art.Nr: 13600092 (AMP 164532-4)
inkl. Gehuse fr 15pol. Sub-D
Art.Nr. 13600021
(Anschlu an Zhlwerke)
Stecker 16: 7pol Buchsengehuse RM2.54 Art.Nr: 13100073 (Molex 22-01-2075)
(Anschlu an CC-46)
Stecker 17: 4pol Buchsengehuse RM2.54 Art.Nr: 13100014 (Molex 22-01-2045)
(Anschlu an WBA-Statusanzeige)
AGI
2352 Gumpoldskirchen
Wiener Strae 158
ELEK38010094-3.xls / Plug-Description
Stecker 18: 3pol Buchsengehuse RM2.54 Art.Nr: 13100066 (Molex 22-01-2035)
(Anschlu an Mnzkanallichtschranke 1)
Stecker 19: 3pol Buchsengehuse RM2.54 Art.Nr: 13100066 (Molex 22-01-2035)
(Anschlu an Mnzkanallichtschranke 2)
Stecker 20: 2pol MOLEX Buchsengehuse Mini-Fit; Art.Nr: 13100053 (Molex 39-01-2020)
(Anschlu an Mnzweiche)
Stecker 21: 3pol Buchsengehuse RM2.54 Art.Nr: 13100066 (Molex 22-01-2035)
(Anschlu an Backplane, Mnzweiche[X6])
Stecker 22: 5pol Buchsengehuse RM2.54 Art.Nr: 13100058 (Molex 22-01-2055)
(Anschlu an Backplane, Mnzkanallichtschranke [X5])
Stecker 23: 4pol Buchsengehuse RM2.54 Art.Nr: 13100014 (Molex 22-01-2045)
(Anschlu an Backplane, LED-WBA [X15])
Stecker 24: 8pol Buchsengehuse RM2.54 Art.Nr: 13100044 (Molex 22-01-2085)
(Anschlu an Backplane, CC-46 [X8])
Stecker 25: 15pol Sub-D Stecker Art.Nr: 13600091 (AMP: 167293-1)
inkl. Gehuse fr 15pol. Sub-D
Art.Nr. 13600021
(Anschlu an Backplane, Zhlwerke [X9])
Stecker 26: 2pol Mini-Fit Buchsengehuse Art.Nr: 13100053 (Molex 39-01-2020)
(Stecker fr Banknotenprfer-Trschalter)
Stecker 28: 4pol Tel. Modulstecker Art.Nr: 13800031
(Anschlu an Backplane [X28], fr Platine P422)
Stecker 29: 4pol Tel. Modulstecker Art.Nr: 13800031
(serieller Anschlu fr Platine P422)
Stecker 30: 10pol Pfostenverbinder, schneidklemm Art.Nr: 13300001 (Harting 09 18 510 7803)
(Anschlu an Backplane fr NRI [X7])
Stecker 31: 10pol Pfostenverbinder, schneidklemm Art.Nr: 13300001 (Harting 09 18 510 7803)
(Anschlu NRI)
Stecker 32: 6pol MOLEX Stiftgehuse Mini-Fit; Art.Nr: 13100056 (Molex 39-01-2061)
(Anschlu fr Spannungsversorgung 6,5" TFT)
Stecker 33: 4pol MOLEX Buchsengehuse Mini-Fit; Art.Nr: 13100026 (Molex 39-01-2040)
(Anschlu an P422)
Stecker 34: 6.3mm Flachstecker
6.3mm Flachstecker: AMP 5-160 432-3 oder Seno
Steckhlsengehuse fr 6.3mm: AMP 926539-1 oder Seno
(Anschlu an Lichtkreis bei Grandroulette)
Art.Nr. 13800004
Art.Nr. 21000007
Stecker 35: 12pol MOLEX Buchsengehuse Mini-Fit; Art.Nr: 13100032 (Molex 39-01-2120)
(Anschlu an Backplane) [X10] zustzliche Backplaneversorgung
Stecker 37: 2pol Mini-Fit Buchsengehuse Art.Nr: 13100053 (Molex 39-01-2020)
(Stecker fr LED-Controller +24V)
AGI
2352 Gumpoldskirchen
Wiener Strae 158
ELEK38010094-3.xls / Plug-Description
Stecker 38: 4pol Buchsengehuse RM2.54 Art.Nr: 13100014 (Molex 22-01-2045)
(Anschlu an LED Streifen oben + 24VDC)
Stecker 39: 2pol Mini-Fit Buchsengehuse Art.Nr: 13100053 (Molex 39-01-2020)
(Stecker fr Topper Versorgung +12V)
Key01,Key02,Key03 mit 2x6,3x0,8mm Winkelflachsteckhlsen 90 mit Gehuse (AGI Nr:13650094+21000183)
(Anschlu fr Schlsselschalter)
S01 bis S15 und S21 je 2x 2.8mm x 0.5 Flachstecker 90 gewinkelt
2.8mm Flachstecker: INARCA 0010982001
Art.Nr.13800055
(Anschlu fr Lorenzo Tasten)
ELEK38010094-3.xls / Plug-Description
X11 Crimp. oder Parallelverbinder
(orange/schwarz) GND fr SS
X12 Crimp. oder Parallelverbinder
(wei/gelb) Start Taste
X13 Crimp. oder Parallelverbinder
(orange/schwarz) GND
13800094
(4x 0.5= 2.00mm)
Kappe : 13800096 (gelb)
13800094
(4x 0.35 + 1x 0.5= 1.9mm)
Kappe : 13800096 (gelb)
13800094
(3x 0.5= 1.5mm)
Kappe : 13800096 (gelb)
AGI
2352 Gumpoldskirchen
Wiener Strae 158
ELEK38010094-3.xls
Verlegeplan
Farbe
colour
mm
von
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
rot
rot
violett/braun
wei/violett
wei/orange
gelb/blau
wei/schwarz
rot/blau
braun/schwarz
grau/schwarz
rosa/blau
grau
grn/schwarz
grau/violett
rosa
red
red
violet/brown
white/violet
white/orange
yellow/blue
white/black
red/blue
brown/black
grey/black
pink/blue
grey
green/black
grey/violet
pink
0.35
0.35
0.35
0.35
0.50
0.35
0.50
0.35
0.50
0.35
0.35
0.35
0.35
0.35
0.35
ST01/Pin01a
ST01/Pin01c
ST01/Pin04a
ST01/Pin04c
ST01/Pin05a
ST01/Pin05c
ST01/Pin06a
ST01/Pin06c
ST01/Pin07a
ST01/Pin07c
ST01/Pin08a
ST01/Pin08c
ST01/Pin09a
ST01/Pin09c
ST01/Pin10a
ST04/Pin01
ST02/Pin01
S21
H21
KEY 3
H06
KEY 2
H05
KEY 1
H04
ST02/Pin02
H03
S18
H02
ST26/Pin01
17
18
18a
18b
18c
19
20
21
22
23
24
25
26
27
28
29
30
30a
30b
31
32
33
34
35
36
37
38
39
40
41
wei/blau
orange/schwarz
orange/schwarz
orange/schwarz
orange/schwarz
gelb
orange/schwarz
gelb
blau/schwarz
braun/blau
orange/braun
rosa/braun
grau/grn
gelb/violett
blau/violett
rosa/grau
wei/gelb
wei/gelb
wei/gelb
wei/rot
gelb/rot
violett/schwarz
gelb/rosa
rosa/orange
rosa/schwarz
rot/schwarz
braun/grau
grn/braun
gelb/braun
wei/grau
white/blue
orange/black
orange/black
orange/black
orange/black
yellow
orange/black
yellow
blue/black
brown/blue
orange/brown
pink/brown
grey/green
yellow/violet
blue/violet
pink/grey
white/yellow
white/yellow
white/yellow
white/red
yellow/red
violet/black
yellow/pink
pink/orange
pink/black
red/black
brown/grey
green /brown
yellow/brown
white/grey
0.35
0.5
0.5
0.5
0.5
0.5
0.35
0.5
0.35
0.35
0.35
0.35
0.35
0.35
0.35
0.35
0.35
0.35
0.35
0.35
0.35
0.5
0.35
0.5
0.35
0.5
0.35
0.35
0.35
0.35
ST01/Pin10c
ST01/Pin11a
X11
X11
X11
ST01/Pin11c
ST01/Pin12a
ST01/Pin12c
ST01/Pin13a
ST01/Pin13c
ST01/Pin14a
ST01/Pin14c
ST01/Pin15a
ST01/Pin15c
ST01/Pin16a
ST01/Pin16c
ST01/Pin17a
X12
X12
ST01/Pin17c
ST01/Pin18a
ST01/Pin18c
ST01/Pin19a
ST01/Pin19c
ST01/Pin20a
ST01/Pin20c
ST01/Pin23a
ST01/Pin24a
ST01/Pin25a
ST01/Pin25c
H01
X11
KEY 3
KEY 2
KEY 1
ST07/Pin01
ST02/Pin03
ST03/Pin04
S16
H15
S15
H14
S14
H13
S13
ST04/Pin02
X12
S12
ST03/Pin02
ST03/Pin01
S11
ST07/Pin04
S10
ST07/Pin02
S09
ST07/Pin03
S08
S07
S06
H12
AGI
Wiener Strae 158
2352 Gumpoldskirchen
bis
(NO)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(NO)
(1)
(NO)
(1)
(NO)
(1)
(NO)
(NO)
(NO)
(NO)
(NO)
(NO)
(NO)
(NO)
(1)
Funktion
Lnge
+5VDC (NFS)
+5VDC (NFS)
RESERVE
RESERVE
Schlsselschalter 3 (Test)
PLAY 7 LINES
Schlsselschalter 2 (Audit)
PLAY 5 LINES
Schlsselschalter 1 (Attendant)
BET 2 PER LINE
doorswitch (receiver)
PLAY 3 LINES
doorswitch (door in door)
BET 1 PER LINE
doorswitch (BNP)
1510
1070
1320
1320
1750
1240
1780
1190
1810
1120
1070
1220
1070
1090
1270
PLAY 1 LINE
GND
GND
GND
GND
+12VDC
GND
+12VDC
doorswitch (drop)
SERVICE
SERVICE
COLLECT
COLLECT
PLAY 9 LINES
PLAY 9 LINES
doorswitch (transmitter)
START
START
START
enable lever
TAKE WIN
toplight (reserve)
GAMBLE
toplight (blue)
BET 10 PER LINE
toplight (white)
BET 5 PER LINE
BET 3 PER LINE
PLAY 7 LINES
AUTO START
1090
1340
510
540
570
2290
1070
1010
1425
1170
1170
1120
1120
1370
1370
1510
300
1190
810
1010
1470
2290
1390
2290
1390
2290
1340
1290
1240
1390
ELEK38010094-3.xls
Verlegeplan
42
43
44
45
46
47
48
49
50
51
52
52a
52b
53
53a
53b
53c
53d
rot/braun
rot/grau
gelb/schwarz
orange/violett
rot/violett
wei/braun
gelb/grau
blau/grau
rosa/violett
blau/grn
orange/schwarz
orange/schwarz
orange/schwarz
orange/schwarz
orange/schwarz
orange/schwarz
schwarz
schwarz
red/brown
red/grey
yellow/black
orange/violet
red/violet
white/brown
yellow/grey
blue/grey
pink/violet
blue/green
orange/black
orange/black
orange/black
orange/black
orange/black
orange/black
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
black
black
0.35
0.35
0.35
0.35
0.35
0.35
0.35
0.35
0.35
0.35
0.5
0.5
0.5
0.35
0.35
0.35
0.35
0.5
ST01/Pin26a
ST01/Pin26c
ST01/Pin27a
ST01/Pin27c
ST01/Pin28a
ST01/Pin28c
ST01/Pin29a
ST01/Pin29c
ST01/Pin30a
ST01/Pin30c
ST01/Pin22a
X14
X14
ST01/Pin21a
X13
X13
X13
X13
S05
H11
S04
H10
S03
H09
S02
H08
S01
H07
X14
S16
S18
X13
ST26/Pin02
ST03/Pin03
ST38/Pin04
ST39/Pin01
orange/schwarz
orange/schwarz
orange/schwarz
orange/schwarz
orange/schwarz
orange/schwarz
orange/schwarz
orange/schwarz
orange/schwarz
orange/black
orange/black
orange/black
orange/black
orange/black
orange/black
orange/black
orange/black
orange/black
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
ST01/Pin31a
X7
X7
X7
X7
X7
X7
X7
X7
X7
S07
S21
S08
S13
S09
S10
S11
S12
gelb
gelb
gelb
gelb
gelb
gelb
gelb
gelb
gelb
orange/schwarz
orange/schwarz
orange/schwarz
orange/schwarz
orange/schwarz
orange/schwarz
orange/schwarz
orange/schwarz
orange/schwarz
gelb
gelb
gelb
gelb
gelb
gelb
gelb
gelb
gelb
yellow
yellow
yellow
yellow
yellow
yellow
yellow
yellow
yellow
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
ST01/Pin31c
X6
X6
X6
X6
X6
X6
X6
X6
ST01/Pin32a
X8
X8
X8
X8
X8
X8
X8
X8
ST01/Pin32c
X9
X9
X9
X9
X9
X9
X9
X9
X6
H07
H21
H08
H13
H09
H10
H11
H12
X8
S01
S02
S03
S04
S05
S06
S14
S15
X9
H01
H02
H03
H04
H05
H06
H14
H15
orange/black
orange/black
orange/black
orange/black
orange/black
orange/black
orange/black
orange/black
orange/black
yellow
yellow
yellow
yellow
yellow
yellow
yellow
yellow
yellow
AGI
Wiener Strae 158
2352 Gumpoldskirchen
(NO)
(1)
(NO)
(1)
(NO)
(1)
(NO)
(1)
(NO)
(1)
(C)
(C)
(C)
(C)
(C)
(C)
(C)
(C)
(2)
(2)
(2)
(2)
(2)
(2)
(2)
(2)
(C)
(C)
(C)
(C)
(C)
(C)
(C)
(C)
(2)
(2)
(2)
(2)
(2)
(2)
(2)
(2)
PLAY 5 LINES
TAKE WIN
BET 2 PER LINE
GAMBLE
PLAY 3 LINES
BET 10 PER LINE
BET 1 PER LINE
BET 5 PER LINE
PLAY 1 LINE
BET 3 PER LINE
GND
GND
GND
GND
GND
GND
GND
GND
1190
1470
1120
1390
1220
1390
1090
1340
1090
1290
340
1265
830
840
530
270
1650
1600
GND
GND
GND
GND
GND
GND
GND
GND
GND
1270
220
250
170
200
220
220
300
220
+12VDC
+12VDC
+12VDC
+12VDC
+12VDC
+12VDC
+12VDC
+12VDC
+12VDC
GND
GND
GND
GND
GND
GND
GND
GND
GND
+12VDC
+12VDC
+12VDC
+12VDC
+12VDC
+12VDC
+12VDC
+12VDC
+12VDC
1320
270
300
220
250
170
170
250
170
1120
270
270
200
300
170
220
300
250
1020
170
170
300
200
270
320
200
250
Verlegeplan
91
schwarz
92
schwarz
93
schwarz
94
schwarz
95
schwarz
96
schwarz
97 orange/schwarz
98
schwarz
98a
schwarz
98b
schwarz
99
gelb
100
gelb
101
gelb
102
gelb
103
gelb
103a
gelb
103b
gelb
104
rot
105
rot
106
rot
107
schwarz
108
gelb
109
gelb
110
grn
111
grn
112
grn
112a
grn
113
schwarz
114
schwarz
115
violett
116
orange
117
grn
118
wei
119
wei
120
wei
121
wei
122
wei
123
schwarz
124
schwarz
125
126
127
128
rot/schwarz
orange/schwarz
orange/grn
orange/schwarz
black
black
black
black
black
black
ELEK38010094-3.xls
black
black
black
yellow
yellow
yellow
yellow
yellow
yellow
yellow
red
red
red
black
yellow
yellow
green
green
green
green
black
black
violet
orange
green
white
white
white
white
white
black
black
1.0
1.0
1.0
1.0
1.0
1.0
0.5
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
0.5
1.0
1.0
0.5
1.0
1.0
1.0
1.0
1.0
1.0
0.35
1.0
1.0
1.0
0.5
1.0
1.0
1.0
1.0
1.0
1.0
0.5
1.0
ST08/Pin05
X3
X3
X3
X3
X3
X3
X3
X3
X3
ST08/Pin07
X2
X2
X2
X2
X2
X2
ST08/Pin01
ST08/Pin02
ST08/Pin03
ST08/Pin04
ST08/Pin06
ST08/Pin08
ST08/Pin09
X10
X10
X10
ST08/Pin12
ST08/Pin13
ST08/Pin14
ST08/Pin17
ST08/Pin18
ST09/Pin01
ST09/Pin02
X1
X1
ST09/Pin03
ST09/Pin06
ST09/Pin05
X3
ST32/Pin01
ST32/Pin02
ST05/Pin02
ST12/Pin04
ST06/Pin01
ST33/Pin02
ST05/Pin04
ST35/Pin04
ST35/Pin02
X2
ST05/Pin03
ST32/Pin04
ST32/Pin05
ST06/Pin02
ST33/Pin04
ST39/Pin02
ST12/Pin01
ST32/Pin03
ST33/Pin03
ST09/Pin04
ST13/Pin01
ST12/Pin09
X10
ST05/Pin01
ST32/Pin06
ST38/Pin03
ST12/Pin02
ST12/Pin06
ST12/Pin12
ST12/Pin11
ST12/Pin05
ST12/Pin03
X1
ST05/Pin05
ST34
ST11
ST33/Pin01
ST05/Pin06
GND (NFS)
GND (NFS)
GND (NFS)
GND (NFS)
GND (NFS)
GND (NFS)
GND (NFS)
GND (NFS)
GND (NFS)
GND (NFS)
+12VDC (NFS)
+12VDC (NFS)
+12VDC (NFS)
+12VDC (NFS)
+12VDC (NFS)
+12VDC (NFS)
+12VDC (NFS)
+5VDC (NFS)
+5VDC (NFS)
+5VDC (NFS)
GND (NFS)
+12VDC (NFS)
+12VDC (NFS)
+24VDC (NFS)
+24VDC (NFS)
+24VDC (NFS)
+24VDC (NFS)
GND (NFS)
GND (NFS)
-12VDC (NFS)
PFD
+24VDC (NFS)
+12VDC (Trafo)
+12VDC (Trafo)
+12VDC (Trafo)
+12VDC (Trafo)
+12VDC (Trafo)
GND (Trafo)
GND (Trafo)
200
990
990
920
500
880
940
920
530
530
300
820
1090
1090
780
1040
1580
600
1090
1040
1380
620
600
430
690
1220
1500
600
600
600
600
600
1680
150
1190
1850
2610
2120
1240
red/black
orange/black
orange/green
orange/black
0.35
0.35
0.35
0.35
ST14/Pin01
ST14/Pin02
ST14/Pin03
ST14/Pin04
LS-r
LS-r
LS-l
LS-l
audio rechts
audio-GND
audio links
audio-GND
1340
1340
940
940
orange/black
AGI
Wiener Strae 158
2352 Gumpoldskirchen
Verlegeplan
ELEK38010094-3.xls
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
rot/grn
rosa/grn
grn
gelb/violett
blau/violett
braun/violett
rosa/orange
grn/grau
rot/schwarz
orange/schwarz
orange/schwarz
blau
orange/rot
gelb
gelb
red/green
pink/green
green
yellow/violet
blue/violet
brown/violet
pink/orange
green/grey
red/black
orange/black
orange/black
blue
orange/red
yellow
yellow
0.35
0.35
0.35
0.35
0.35
0.35
0.35
0.35
0.35
0.35
0.35
0.35
0.35
0.35
0.35
ST15/Pin01
ST15/Pin02
ST15/Pin03
ST15/Pin04
ST15/Pin05
ST15/Pin06
ST15/Pin07
ST15/Pin08
ST15/Pin09
ST15/Pin10
ST15/Pin11
ST15/Pin12
ST15/Pin13
ST15/Pin14
ST15/Pin15
ST25/Pin01
ST25/Pin02
ST25/Pin03
ST25/Pin04
ST25/Pin05
ST25/Pin06
ST25/Pin07
ST25/Pin08
ST25/Pin09
ST25/Pin10
ST25/Pin11
ST25/Pin12
ST25/Pin13
ST25/Pin14
ST25/Pin15
meter 1
meter 2
meter 3
meter 4
meter 5
meter 6
lamps on
metercount
m-security
GND
GND
meter 7
meter 8
+12VDC
+12VDC
1145
1145
1145
1145
1145
1145
1145
1145
1145
1145
1145
1145
1145
1145
1145
144
145
146
147
148
schwarz
orange
blau
gelb
violett
black
orange
blue
yellow
violet
0.35
0.35
0.35
0.35
0.35
ST16/Pin01
ST16/Pin03
ST16/Pin04
ST16/Pin06
ST16/Pin07
ST24/Pin04
ST24/Pin01
ST24/Pin03
ST24/Pin05
ST24/Pin06
GND
Tilt
credit output
+12VDC
enable
1435
1435
1435
1435
1435
149
150
151
152
gelb
rosa
blau
violett
yellow
pink
blue
violet
0.35
0.35
0.35
0.35
ST17/Pin01
ST17/Pin02
ST17/Pin03
ST17/Pin04
ST23/Pin01
ST23/Pin02
ST23/Pin03
ST23/Pin04
+12VDC
LED A (rot)
LED B (grn)
LED C (gelb)
1455
1455
1455
1455
153
154
155
156
157
158
159
160
gelb
gelb
gelb
schwarz
schwarz
schwarz
rosa/grau
wei/violett
yellow
yellow
yellow
black
black
black
pink/grey
white/violet
0.35
0.35
0.35
0.35
0.35
0.35
0.35
0.35
ST22/Pin01
X5
X5
ST22/Pin02
X4
X4
ST22/Pin03
ST22/Pin04
X5
ST18/Pin03
ST19/Pin03
X4
ST18/Pin01
ST19/Pin01
ST18/Pin02
ST19/Pin02
+12VDC
+12VDC
+12VDC
GND
GND
GND
Signal A
Signal B
1475
290
220
1425
240
270
1565
1595
161
162
rot/violett
gelb
red/violet
yellow
0.35
0.35
ST21/Pin01
ST21/Pin03
ST20/Pin02
ST20/Pin01
CCHS1
+12VDC
1295
1295
163
4xAWG26
ST28
ST29
serielle Verbindung
990
164
AWG 28/7
ST-30
ST31
Flachbandkabel
1355
165
166
rot
rot
red
red
1.0
1.0
ST08/Pin10
ST08/Pin11
ST35/Pin01
ST12/Pin07
+5VDC
+5VDC
630
600
167
168
grn
schwarz
green
black
1.0
1.0
ST35/Pin05
ST35/Pin08
ST37/Pin01
ST37/Pin02
+24VDC
GND
870
870
AGI
Wiener Strae 158
2352 Gumpoldskirchen
ELEK38010094-3.xls/Ergnzung
Folgende Kontakte werden im Hauptkabelbaum 38010094-3 verwendet.
AGI Art.Nr.
Bezeichnung
Molex Nr.
Verwendung
Anzahl
13650061
AMP: 166500-2
ST01
56
13650002
02-09-2101
ST-06
Gesamt
2
2
Pin 01,02
13650008
02-09-1102
ST-07
Gesamt
4
4
Pin 01,02,03,04
13650074
39-00-0083
ST-08
ST-32
Gesamt
14
6
20
13650075
39-00-0061
ST-08
Gesamt
2
2
Pin 03,17
13650072
39-00-0079
ST-05
ST-13
ST-12
ST-09
ST-33
ST-35
ST-37
Gesamt
6
1
9
5
1
5
2
29
Pin 01-06
Pin 01
Pin 01-06,07,09,12
Pin 01-05
Pin 04
Pin 01,02,04,05,08
Pin 01,02
13650073
39-00-0059
ST-03
ST-09
ST-12
ST-14
ST-26
ST-33
ST-20
ST-39
Gesamt
4
1
1
4
2
3
2
2
19
Pin 01-04
Pin 06
Pin 11
Pin 01-04
Pin 01,02
Pin 01,02,03
Pin 01,02
Pin 01,02
AGI
2352 Gumpoldskirchen
Wiener Strae 158
Pin
ELEK38010094-3.xls/Ergnzung
13650013
97-00-0444
ST-02
ST-04
ST-16
ST-17
ST-18
ST-19
ST-21
ST-22
ST-23
ST-24
ST-38
Gesamt
3
2
5
4
3
3
2
4
4
5
2
37
Pin 01-03
Pin 01,02
Pin 01,03,04,06,07
Pin 01-04
Pin 01-03
Pin 01-03
Pin 01,03
Pin 01-04
Pin 01-04
Pin 01,03-06
Pin 03,04
13650067
AMP: 166051-1
ST15
15
Pin: 01 - 15
13650068
AMP: 166053-1
ST25
15
Pin: 01 - 15
13800004
Seno 0010129001
ST11
ST34
Gesamt
1
1
2
13800100
Seno 0010915001
S16
S18
LS-L
LS-R
Gesamt
2
2
2
2
8
AGI
2352 Gumpoldskirchen
Wiener Strae 158
Pin: No; C
Pin: No; C
Pin: +; Pin: +; -
ELEK38010094-3.xls/Ergnzung
13800055
13650094
AGI
2352 Gumpoldskirchen
Wiener Strae 158
Seno 0010982001
Tyco 1-280050-2
S01
S02
S03
S04
S05
S06
S07
S08
S09
S10
S11
S12
S13
S14
S15
S21
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
Pin: NO; C
Pin: NO; C
Pin: NO; C
Pin: NO; C
Pin: NO; C
Pin: NO; C
Pin: NO; C
Pin: NO; C
Pin: NO; C
Pin: NO; C
Pin: NO; C
Pin: NO; C
Pin: NO; C
Pin: NO; C
Pin: NO; C
Pin: NO; C
H01
H02
H03
H04
H05
H06
H07
H08
H09
H10
H11
H12
H13
H14
H15
H21
Gesamt
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
64
Pin: 01; 02
Pin: 01; 02
Pin: 01; 02
Pin: 01; 02
Pin: 01; 02
Pin: 01; 02
Pin: 01; 02
Pin: 01; 02
Pin: 01; 02
Pin: 01; 02
Pin: 01; 02
Pin: 01; 02
Pin: 01; 02
Pin: 01; 02
Pin: 01; 02
Pin: 01; 02
Key 01
Key 02
Key 03
Gesamt
2
2
2
6
Pin: C; NO
Pin: C; NO
Pin: C; NO
ELEK38010094-3.xls/Ergnzung
21000183
AGI
2352 Gumpoldskirchen
Wiener Strae 158
Key 01
Key 02
Key 03
Gesamt
2
2
2
6
Pin: C; NO
Pin: C; NO
Pin: C; NO
ELEK38010094-3.xls/nderungen _Changes
AGI
2352 Gumpoldskirchen
Wiener Strae 158
ELEK38010094-3.xls/nderungen _Changes
English:
ST01: additional 100mmm Certotape
ST03: no doublecrimp, X12 additionaly
ST05: extra length 34cm + Certotape
ST08: Pin 10 and Pin11 additionaly (red +5V) (line 165 and 166)
ST12: Pin07 additionaly (red +5V) (line 168)
ST18 and ST19: 20mm longer
Crimpconnector X4 and X5 must be fixed backwards using cable tie
Certotape additionaly
ST27 and S17 canceld (line 16 und 54 canceld)
ST31: FBK 30mm longer
ST33 Pin 4 yellow line +12V additionaly from X2 (1.0) (line 103a)
ST35 new
ST37 new (line 167 and 168)
ST38 new (supply for Led +24V)
ST39 new (supply for Topper +12V) (yellow 103b and black 53d)
S18: 80mm longer
X11 new (orange/black 18,18a,18b,18c)
X12 new (3x wht/yel line 30,30a,30b)
X13 new (orange/black 53,53a,53b, black 53c,53d)
X14 new (orange/black 52,52a,52b)
X2 (yellow 1.0 and 0.5 new) ( line: 103a and 103b)
X10 green 0.35 new for ST38 (line 112a)
X3 black 2x 1.0 new (line 98a and 98b)
AGI
2352 Gumpoldskirchen
Wiener Strae 158
ELEK38010094-3.xls/Backplanepinning
GND
+12VDC
GND
+12VDC
INPUT 5
OUTPUT 1
INPUT 6
OUTPUT 2
INPUT 7
OUTPUT 3
INPUT 8
OUTPUT 4
INPUT 9
OUTPUT 5
INPUT 10
OUTPUT 6
INPUT 11
OUTPUT 7
INPUT 12
OUTPUT 8
GND
+12VDC
GND
+12VDC
INPUT 13
OUTPUT 9
INPUT 14
OUTPUT 10
INPUT 15
OUTPUT 11
INPUT 16
OUTPUT 12
INPUT 17
OUTPUT 13
INPUT 18
OUTPUT 14
INPUT 19
OUTPUT 15
INPUT 20
OUTPUT 16
GND
+12VDC
GND
+12VDC
INPUT 21
OUTPUT 17
AGI
2352 Gumpoldskirchen
Wiener Strae 158
Pinnbelegung Kabelbaum
(64pol. VG-Federleiste)
Treiber
Pin Nr:
32a
31a
30a
ULN2803
29a
ULN2803
28a
ULN2803
27a
ULN2803
26a
ULN2803
25a
ULN2803
24a
ULN2803
23a
ULN2803
22a
21a
20a
ULN2803
19a
ULN2803
18a
ULN2803
17a
ULN2803
16a
ULN2803
15a
ULN2803
14a
ULN2803
13a
ULN2803
Funktion
GND
32c +12VDC
GND
31c +12VDC
Taste 1
30c Lampe 7
Taste 2
29c Lampe 8
Taste 3
28c Lampe 9
Taste 4
27c Lampe 10
Taste 5
26c Lampe 11
Taste 6
25c Lampe 12
Taste 7
24c nc
Taste 8
23c nc
GND
22c +12VDC
GND
21c +12VDC
Taste 9
20c toplight (wei) 1
Taste 10
19c toplight (blau) 2
Taste 11
18c toplight (reserve) 3
Taste 12
17c Freigabe Hebel
Taste 13
16c Trschalter-optisch (transmitter-doorswitch)
Taste 14
15c Lampe 13
Taste 15
14c Lampe 14
Trschalter DROP
13c Lampe 15
GND
12c +12VDC
11a
GND
11c +12VDC
Trschalter BNP
10a
10c Lampe 1
12a
ULN2064
Bezeichnung
k. Bezeichnug
GND
+12VDC
GND
+12VDC
S01
H07
S02
H08
S03
H09
S04
H10
S05
H11
S06
H12
S07
***
S08
***
GND
+12VDC
GND
+12VDC
S09
H18
S10
H19
S11
H20
S12
***
S13
***
S14
H13
S15
H14
S16
H15
GND
+12VDC
GND
+12VDC
S17
H01
GND
+12VDC
GND
+12VDC
PLAY 1 LINE
BET 3 PER LINE
BET 1 PER LINE
BET 5 PER LINE
PLAY 3 LINES
BET 10 PER LINE
BET 2 PER LINE
GAMBLE
PLAY 5 LINES
TAKE WIN
PLAY 7 LINES
AUTO START
BET 3 PER LINE
***
BET 5 PER LINE
***
GND
+12VDC
GND
+12VDC
BET 10 PER LINE
TOPLIGHT (white)
GAMBLE
TOPLIGHT (blue)
TAKE WIN
TOPLIGHT (reserve)
AUTO START
enable lever
PLAY 9 LINES
doorswitch (transmitter)
COLLECT
PLAY 9 LINES
SERVICE
COLLECT
doorswitch-drop
SERVICE
GND
+12VDC
GND
+12VDC
doorswitch-BNP
PLAY 1 LINE
ELEK38010094-3.xls/Backplanepinning
24a
INPUT 22
24c
25a
9a
OUTPUT 18 ULN2064
INPUT 23
25c
26a
8a
OUTPUT 19 ULN2064
INPUT 24
26c
27a
7a
INPUT 25
28a
6a
INPUT 26
29a
5a
INPUT 27
30a
4a
OUTPUT 23 ULN2064
INPUT 28
30c
31a
31c
32a
32c
3a
OUTPUT 24 ULN2064
VCC +5VDC
VCC +5VDC
VCC +5VDC
VCC +5VDC
AGI
2352 Gumpoldskirchen
Wiener Strae 158
Schlsselschalter 2
6c Lampe 5
OUTPUT 22 ULN2064
29c
Schlsselschalter 1
7c Lampe 4
OUTPUT 21 ULN2064
28c
8c Lampe 3
OUTPUT 20 ULN2064
27c
9c Lampe 2
2a
1a
Schlsselschalter 3
5c Lampe 6
Schalter 21
4c Lampe 21
nc
3c nc
VCC +5VDC
2c VCC +5VDC
VCC +5VDC
1c VCC +5VDC
S18
H02
?
H03
KEY1
H04
KEY2
H05
KEY3
H06
S21
H21
S22
H22
VCC +5VDC
VCC +5VDC
VCC +5VDC
VCC +5VDC
***
VCC +5VDC
VCC +5VDC
VCC +5VDC
VCC +5VDC