Documente Academic
Documente Profesional
Documente Cultură
Contents
Chapter 7. Locations................................................................28
Locating components and connectors.................................................. 28
Appendix. Statement..............................................................67
ii
Using eSupport
For Key Commodities (Examples - hard disk drive, system board,
microprocessor, LCD, and memory)
eSupport can be used to view the list of key commodities built in a
particular machine serial.
eSupport can be accessed at the following Web site:
http://consumersupport.lenovo.com
To view the key commodities:
1. Click Parts information.
2. Under Parts information, click Parts lookup.
3. Under Parts lookup, type the model type and serial number; then
click Continue.
The key commodities are returned in the eSupport record under
Parts shipped with your system.
For the remaining FRUs (the complete list of FRUs at the MT Model level)
eSupport can be used to view the complete list of FRUs for a machine
type and model.
To view the complete list of FRUs for a machine type:
1. Point your browser to http://consumersupport.lenovo.com.
2. Type the machine type (Example: 8129) in the Use Quick Path field;
then click Go.
3. Under Browse by product, click Continue.
4. Under Important information, click Parts information.
5. In the Refine results field, select Service parts; then click the entry for
your machine type.
The list of service parts by description, with applicable machine type
model and FRU part number is displayed.
Safety information
This chapter contains the safety information that you need to be familiar
with before servicing a computer.
General safety
Follow these rules to ensure general safety:
Observe good housekeeping in the area of the machines during and
after maintenance.
When lifting any heavy object:
1. Ensure you can stand safely without slipping.
2. Distribute the weight of the object equally between your feet.
3. Use a slow lifting force. Never move suddenly or twist when you
attempt to lift.
4. Lift by standing or by pushing up with your leg muscles; this action
removes the strain from the muscles in your back. Do not attempt to
lift any objects that weigh more than 16 kg (35 lb) or objects that you
think are too heavy for you.
Do not perform any action that causes hazards to the customer, or that
makes the equipment unsafe.
Before you start the machine, ensure that other service representatives
and the customers personnel are not in a hazardous position.
Place removed covers and other parts in a safe place, away from all
personnel, while you are servicing the machine.
Keep your tool case away from walk areas so that other people will not
trip over it.
Do not wear loose clothing that can be trapped in the moving parts of a
machine. Ensure that your sleeves are fastened or rolled up above your
elbows. If your hair is long, fasten it.
Insert the ends of your necktie or scarf inside clothing or fasten it with
a nonconductive clip, approximately 8 centimeters (3 inches) from the
end.
Do not wear jewelry, chains, metal-frame eyeglasses, or metal fasteners
for your clothing.
Remember: Metal objects are good electrical conductors.
Electrical safety
CAUTION:
Electrical current from power, telephone, and communication cables
can be hazardous. To avoid personal injury or equipment damage,
disconnect the attached power cords, telecommunication systems,
networks, and modems before you open the server/workstation covers,
unless instructed otherwise in the installation and configuration
procedures.
Observe the following rules when working on electrical equipment.
Important: Use only approved tools and test equipment. Some hand
tools have handles covered with a soft material that does not
insulate you when working with live electrical currents.
Many customers have, near their equipment, rubber floor mats
that contain small conductive fibers to decrease electrostatic
discharges. Do not use this type of mat to protect yourself
from electrical shock.
Find the room emergency power-off (EPO) switch, disconnecting
switch, or electrical outlet. If an electrical accident occurs, you can then
operate the switch or unplug the power cord quickly.
Do not work alone under hazardous conditions or near equipment that
has hazardous voltages.
Disconnect all power before:
Performing a mechanical inspection
Working near power supplies
Removing or installing main units
Before you start to work on the machine, unplug the power cord. If
you cannot unplug it, ask the customer to power-off the wall box
that supplies power to the machine and to lock the wall box in the off
position.
Grounding requirements
Electrical grounding of the computer is required for operator safety and
correct system function. Proper grounding of the electrical outlet can be
verified by a certified electrician.
Safety notices
The caution and danger safety notices in this section are provided in the
the language of English.
DANGER
Electrical current from power, telephone and communication cables is
hazardous.
To avoid a shock hazard:
Do not connect or disconnect any cables or perform installation,
maintenance, or reconfiguration of this product during an electrical
storm.
Connect all power cords to a properly wired and grounded electrical
outlet.
Connect to properly wired outlets any equipment that will be
attached to this product.
When possible, use one hand only to connect or disconnect signal
cables.
Never turn on any equipment when there is evidence of fire, water, or
structural damage.
Disconnect the attached power cords, telecommunications systems,
networks, and modems before you open the device covers, unless
instructed otherwise in the installation and configuration procedures.
Connect and disconnect cables as described in the following table
when installing, moving, or opening covers on this product or
attached devices.
To Connect
1. Turn everything OFF.
2. First, attach all cables to devices.
3. Attach signal cables to
connectors.
4. Attach power cords to outlet.
5. Turn device ON.
To Disconnect
1. Turn everything OFF.
2. First, remove power cords from
outlet.
3. Remove signal cables from
connectors.
4. Remove all cables from devices.
CAUTION:
When replacing the lithium battery, use only Part Number 33F8354 or
an equivalent type battery recommended by the manufacturer. If your
system has a module containing a lithium battery, replace it only with
the same module type made by the same manufacturer. The battery
contains lithium and can explode if not properly used, handled, or
disposed of.
Do not:
Throw or immerse into water
Heat to more than 100C (212F)
Repair or disassemble
Dispose of the battery as required by local ordinances or regulations.
CAUTION:
When laser products (such as CD-ROMs, DVD-ROM drives, fiber optic
devices, or transmitters) are installed, note the following:
Do not remove the covers. Removing the covers of the laser product
could result in exposure to hazardous laser radiation. There are no
serviceable parts inside the device.
Use of controls or adjustments or performance of procedures other
than those specified herein might result in hazardous radiation
exposure.
DANGER:
Some laser products contain an embedded Class 3A or Class 3B laser
diode. Note the following:
Laser radiation when open. Do not stare into the beam, do not view
directly with optical instruments, and avoid direct exposure to the
beam.
10
CAUTION:
Use safe practices when lifting.
CAUTION:
The power control button on the device and the power switch on the
power supply do not turn off the electrical current supplied to the
device. The device also might have more than one power cord. To
remove all electrical current from the device, ensure that all power cords
are disconnected from the power source.
2
1
CAUTION:
Do not place any object weighing more than 82 kg (180 lbs.) on top of
rack-mounted devices.
11
General information
Specifications
This section lists the physical specifications for your computer.
12
General Checkout
Attention
The drives in the computer you are servicing might have been
rearranged or the drive startup sequence changed. Be extremely
careful during write operations such as copying, saving, or
formatting. Data or programs can be overwritten if you select an
incorrect drive.
General error messages appear if a problem or conflict is found by an
application program, the operating system, or both. For an explanation
of these messages, refer to the information supplied with that software
package.
Notes
The default is for this computer to boot up in quiet mode (no beep,
no memory count and checkpoint code display) when no errors are
detected by POST.
To enable beep, memory count, and checkpoint code display when
a successful POST occurs, do the following:
1. Start the Setup Utility program. See Starting the Setup Utility
program.
2. Select Start Options.
3. Set Power-On Self-Test to Enhanced.
Before replacing any FRUs, ensure that the latest level of BIOS is
installed on the system. A down-level BIOS might cause false errors
and unnecessary replacement of the system board.
Use the following procedure to help determine the cause of the problem:
1. Power-off the computer and all external devices.
2. Check all cables and power cords.
3. Set all display controls to the middle position.
4. Power-on all external devices.
13
14
15
The Setup Utility program is used to view and change the configuration
settings of your computer, regardless of which operating system you are
using. However, the operating-system settings might override any similar
settings in the Setup Utility program.
16
Using passwords
By using the Setup Utility program, you can set passwords to prevent
unauthorized persons from gaining access to your computer and data.
See Starting the Setup Utility program. The following types of passwords
are available:
Administrator Password
Power-On Password
You do not have to set any passwords to use your computer. However, if
you decide to set any passwords, read the following sections.
Password considerations
A password can be any combination of up to 8 or 16 characters (a-z and
0-9) and symbols. For security reasons, it is a good idea to use a strong
password that cannot be easily compromised. We suggest the passwords
should adhere to the following rules:
Must have at least seven characters in length
Contain at least one alphabetic character and one numeric character
Setup Utility program and hard disk drive passwords are not case
sensitive
Not be your name or your user name
Not be a common word or a common name
Be significantly different from your previous password
Administrator password
When a Administrator Password is set, it deters unauthorized persons from
changing configuration settings. If you are responsible for maintaining
the settings of several computers, you might want to set a Administrator
Password.
After you set a Administrator Password, a password prompt is displayed
each time you try to access the Setup Utility program.
If both the Administrator and Power-On Password are set, you can type
either password. However, to change any configuration settings, you must
use your Administrator password.
17
Power-On Password
When a Power-On Password is set, you cannot start the Setup Utility
program until a valid password is typed from the keyboard.
18
3. The password dialog box will be displayed. Type the new password, and
press Enter.
4. when prompted to confirm the password, type the password again. If
you type the password correctly, the password will be installed.
To delete a previously set Power-On Password, do the following :
1. From the Security menu, select Set Power-On Password and press
Enter.
2. The password dialog box will be displayed. Enter Current Password and
press Enter. Press Enter in New Password and confirm New Password
dialog. A setup notice will display that changes have been saved.
3. Press Enter to continue.
Using Device
USB Setup
19
20
21
Symptom-to-FRU Index
FRU/Action
The start-up drive is not in the boot Check the configuration and ensure
sequence in configuration.
the start-up drive is in the boot
sequence.
No operating system installed on
the boot drive.
22
Error
FRU/Action
23
Beep symptoms
Beep symptoms are tones or a series of tones separated by pauses
(intervals without sound) during POST.
The following tables describes beep symptoms.
Beep Symptom
1 beep
Memory refresh timer error
FRU/Action
Reseat the memory, or replace with
known good modules.
2 beeps
Parity error in base memory (first
64KB block)
3 beeps
Base memory read/write test error
4 beeps
Fatal error indicating a serious
Motherboard timer not operational problem with the system. Consult
your system manufacturer. Before
declaring the motherboard beyond
all hope, eliminate the possibility
5 beeps
of interference by a malfunctioning
Processor error
add-in card. Remove all expansion
cards except the video adapter.
If beep codes are generated
when all other expansion cards
6 beeps
are absent, consult your system
8042 Gate A20 test error (cannot
manufacturers technical support.
switch to protected mode)
If beep codes are not generated
when all other expansion cards
are absent, one of the add-in cards
7 beeps
is causing the malfunction. Insert
General exception error (processor
the cards back into the system
exception interrupt error)
one at a time until the problem
happens again. This will reveal the
malfunctioning card.
8 beeps
If the system video adapter is an
Display memory error (system video add-in card, replace or reseat the
adapter)
video adapter. If the video adapter
is an integrated part of the system
board, the board may be faulty.
24
Beep Symptom
9 beeps
Phenix BIOS ROM checksum error
FRU/Action
Fatal error indicating a serious
problem with the system. Consult
your system manufacturer. Before
declaring the motherboard beyond
all hope, eliminate the possibility
of interference by a malfunctioning
add-in card. Remove all expansion
10 beeps
cards except the video adapter.
CMOS shutdown register read/write
If beep codes are generated
error
when all other expansion cards
are absent, consult your system
manufacturers technical support.
If beep codes are not generated
when all other expansion cards
11 beeps
are absent, one of the add-in cards
Cache memory test failed
is causing the malfunction. Insert
the cards back into the system
one at a time until the problem
happens again. This will reveal the
malfunctioning card.
25
Keyboard error
System Halted
26
Description/Action
The CMOS Date and/or Time are
invalid. This error can be resolved
by readjusting the system time in
Phenix BIOS Setup.
The CMOS battery is no longer
functional.
Replace the battery.
Checksum of CMOS is incorrect.
The computer loads the default
configuration settings. This error
might indicate that CMOS has
become corrupt due to a weak
CMOS battery.
The IDE/ATAPI device configured
as Primary Master/Primary Slave/
Secondary Master/Secondary Slave
could not be found or initialized.
Make sure the hard drive is correctly
installed.
PS2 Mouse support is enabled in
the BIOS setup butthe device is not
detected. You can plug PS2 Mouse
or set PS2 Mouse support is auto.
Cannot initialize the keyboard.
Make sure the keyboard is properly
connected to the computer and
that no keys are held pressed during
POST.
To purposely configure the
computer without a keyboard, set
keyboardless operation in Setup to
Enable. The BIOS then ignores the
missing keyboard during POST.
The system has been halted. A reset
or power cycle is required to reboot
the machine. This message appears
after a fatal error has been detected.
Pressing the TAB key permits the
user to toggle between the default
POST display screen and a custom
POST display screen.
Description/Action
The BIOS was unable to find a
suitable boot device.
Make sure the boot drive is properly
connected to the computer.
Make sure you have bootable
media.
Undetermined problems
If this computer has a parallel ATA hard disk drive, make sure that the hard
disk drive is jumpered as a master and the optical drive is jumpered as a
slave.
1. Power-off the computer.
2. Remove or disconnect the following components (if installed) one at a
time.
a. External devices (modem, printer, or mouse)
b. Any adapters
c. Memory modules
d. Extended video memory
e. External Cache
f. External Cache RAM
g. Hard disk drive
h. Diskette drive
3. Power-on the computer to re-test the system.
4. Repeat steps 1 through 3 until you find the failing device or adapter.
If all devices and adapters have been removed, and the problem
continues, replace the system board.
27
Locations
Internal components
The following illustration shows the components inside your computer.
Front bezel
Power board
LCD
TV CARD
WLAN
Camera
Camera cable
Inverter
CPU fan
HDD
RAM
HDD cable
Heat Sink
Speaker
ODD
Rear cover
ODD cable
Power cable
28
4
9
29
16
15
3
14
4
5
6
13
12
Microprocessor
1
Memory slots
2
Memory card reader
3
IEEE 1394 connector
4
Headphone connector
5
Microphone connector
6
USB connectors (2)
7
USB connectors (4)
8
Ethernet connector
9
PS2 Keyboard connector
q;
TV tuner (Select models only)
qa
Power connector
qs
qd HDD power cable connector
HDD SATA 2 connector
qf
ODD SATA 1 connector
qg
ODD power cable connector
qh
30
11
10
Replacing hardware
Attention
Note
General information
Pre-disassembly instructions
Before proceeding with the disassembly procedure, make sure that you
do the following:
1. Turn off the power to the system and all peripherals.
2. Unplug all power and signal cables from the computer.
3. Place the system on a flat, stable surface.
31
Turn off the computer and wait 3 to 5 minutes to let the computer
cool before removing the computer cover.
32
5. Gently slide the cover toward the side of the computer, and then
remove it.
6. Push out the latches on both sides of the memory socket to release the
memory module 1 and gently pull the memory module upward to
remove it from its socket 2. Both memory modules can be removed
by using the same procedure.
33
2
1
7. Align then insert the new memory module into the socket 1 and
push down on the top edge of the memory module 2. Make sure the
latches lock the memory module in place.
34
2
2
Turn off the computer and wait 3 to 5 minutes to let the computer
cool before removing the computer cover.
35
36
5. Place the computer upside down on the flat surface. Release the left
and right tabs from the connector housing, then pull each side of the
cover out slightly 1, release the top tabs from the connector housing,
then lift the cover away from the computer 2.
37
38
6. Align the screw holes on the power board to the mounting holes on
the computer cover.
7. Screw back the two screws on the new power board.
8. Connect the power board cable to the power board.
9. Install the computer cover. Refer to Completing the installation .
39
3. Disconnect the LCD panel three cables from the system board 1 and
inverter board 2.
40
41
42
4. Disconnect the speakers cable from the system board 1, and pull out
the left and right speakers from the chassis 2.
43
3. Disconnect the data and power cables from the hard disk drive.
4. Remove the screw that secures the hard disk drive to the chassis.
44
6. Remove the four screws that secure the hard disk drive to the drive
bay.
45
(1.) Insert the new hard disk drive into the drive bay.
9. Screw back the hard disk drive bay back to the chassis.
10. Connect the data and power cables back to the hard disk drive.
11. Install the LCD panel. Refer to steps 5 to 6 of the Replacing the LCD
panel section.
12. Install the computer cover. Refer to Completing the installation .
46
4. Disconnect one end of the ODD data and power cables from the rear
of the optical drive.
47
6. Remove the two screws that secure the optical drive to the metal
bracket.
48
49
panel section.
3. Remove the optical drive. Refer to the steps 3 to 5 of the Replacing
the optical drive section.
4. Disconnect the inverter board cable from the inverter board 1 and
remove the two screws that secure the inverter board to the chassis 2.
50
51
5. Align the four screw holes on the new system fan to the four mounting
holes on the chassis.
6. Insert and tighten the four screws to secure the system fan.
7. Connect the system fan cable to the system board.
8. Install the LCD panel. Refer to steps 5 to 6 of the Replacing the LCD
52
panel section.
9. Install the computer cover. Refer to Completing the installation .
53
54
6. Align then insert the new wireless card to the wireless card connector.
7. Screw back the two screws on the wireless card.
8. Connect the two antenna cables to the wireless card.
9. Install the LCD panel. Refer to steps 5 to 6 of the Replacing the LCD
panel section.
10. Install the computer cover. Refer to Completing the installation .
55
2. Remove the LCD panel. Refer to steps 2 to 4 of the Replacing the LCD
panel section.
3. Disconnect the antenna cable from the TV tuner card 1.
4. Remove the two screws that secure the TV tuner card to the system
board 2.
6. Align then insert the new TV tuner card to the TV tuner connector.
7. Screw back the two screws on the TV tuner card.
8. Connect the antenna cable to the TV tuner card.
9. Install the LCD panel. Refer to steps 5 to 6 of the Replacing the LCD
panel section.
10. Install the computer cover. Refer to Completing the installation .
56
5. Pull the system board away from the chassis and disconnect all the
cables away from the underside of the system board.
57
3
5
2
6
1
58
7
3
2
6
1
9. Set the new heat sink on the CPU, aligning the seven screws in the
heat sink with the screw sockets in the chassis.
10. Tighten the seven screws on the heat sink.
11. Connect related cables to the underside of the system board.
12. Place the system board upside down.
13. Place the system board into the chassis, aligning the screw holes on
the system board with the mounting holes on the chassis.
14. Screw back the eight screws on the system board.
15. Connect related cables to the upside of the system board.
16. Install the LCD panel. Refer to steps 5 to 6 of the Replacing the LCD
panel section.
17. Install the computer cover. Refer to Completing the installation .
59
5. Disconnect all the cables from the upside of the system board.
6. Remove the eight screws that secure the system board to the chassis.
7. Pull the system board away from the chassis and disconnect all the
cables away from the underside of the system board.
60
61
4. Disconnect the failing keyboard cable from the computer and connect
the new keyboard cable to the same connector.
62
Your mouse connected to the USB connector at either side or the rear
of the computer.
4. Disconnect the failing keyboard cable from the computer and connect
the new mouse cable to the same connector.
63
3. Disconnect the failing power cord and adapter from the computer and
connect the new power cord and adapter to the same connector.
64
Attention
4. Carefully install the cover as shown, until it securely snaps into place.
5. Install and tighten the six screws on the chassis.
65
6. Reconnect the external cables and power cords into the computer.
Refer to Locating components and connectors .
Note
In most areas of the world, Lenovo requires the return of the defective
CRU. Information about this will come with the CRU or will come a
few days after the CRU arrives.
66
Additional Service
Information
Power management
Power management reduces the power consumption of certain
components of the computer such as the system power supply, processor,
hard disk drives, and some monitors.
66
A
Appendix. Statement
Statement
67
Welcome to contact us for any inconsistency between the product and all
the manuals included with your computer. For the latest information or
any questions or comments, contact or visit Lenovo website:
Service website: http://consumersupport.lenovo.com
Lenovo is the registered trademark of Lenovo
(Beijing ) Co., Ltd.
68