Documente Academic
Documente Profesional
Documente Cultură
SCG SmartBaord
Caution
Do not use as any buildings structure or other purposes. The installation shall follow the Installation Manual and use only the standard equipments made
by producer.
Do not eat
First Aid
If the dust or any material debris accidentally entered the eye, do not scrub or crush. Clean with clean water several times, and consult the physician
immediately.
Verify that all methods are following the most update of Installation Manual of Products
Installation Manual of Products is always updated. The designer, construction supervisor, and installer shall verify that all methods being used are following
the most update of Installation Manual of Products. They can confirm by the website : www.siamfibrecement.com
0610
Fiber Cement
Board
Non Asbestos
Made from Elephant Portland Cement, Silica and special cellulose without asbestos which
make flexible with long lasting durability.
3.5, 4, 6
NEW
Firm
Water-Resistant
and Non-decay
4-side T
Premium
Resistant to Termites
Long lasting resistance to water, rain and sun without decaying (JIS Standard A5420)
SmartBoard is free.
6 mm. t
time that perform the lifting. Then use his leg power to lift
by holding at 30 cm distance from the panel edge of
SCG SmartBoard.
Termite cannot munch SCG SmartBoard because it is made from Elephant Portland Cement,
Silica and special cellulose all well blened together, which make termites and insects harmless
to SCG SmartBoard
Flexible and blended. No need for watering or moistening and with different bending radius for
different thickness.
4-side T
Special Properties
Squared
R = 4.0 m
R = 2.0 m
R = 1.5 m
Storing Tips
Flex
6 mm.
1.50 m. beding redius
8 mm.
2.0 m. beding redius
10 mm.
2.0 m. beding redius
Wood G
4 mm. th
Light weight,
easy to install and
customize your design
NEW
3-inch S
SCG SmartBoard walls can be designed to suit any rooms of your desire without any steel
beam reinforcement because they are 6 times lighter than traditional brick wall.
Traditional brick wall average
weights
180 kg./sqm.
SCG SmartBoard wall average
weights
30 kg./sqm.
4 mm. th
SCG SmartBoard has less than two times heat conductivity rate than asbestos fiber-cement
(ASTM C117 Standard) that reduces heat transfer from the under roof gap. Reduces in-house
temperature and saves energy.
Ventilate
4 mm. th
Application
Ventilate
4 mm. th
NEW
Internal Ceiling
Usage area
Any room that you want to prevent
problem from termites and moisture,
for example: Bathroom, Kitchen,
Storageroom, etc.
Ventilate
4 mm. th
Series
Squared Edge
Smooth Surface
Wood Grain
Ventilated
External Ceiling
Smooth Surface
Squared
Smooth Surface
Squared Edge
Surface
Ventilated
Wood Grain
Recommended
Thickness
3.5, 4, 6 mm.
Concealed Edge
6 mm.
Smooth Surface
Smooth Surface
Wood Grain Texture
Installation
System
Space Linning,
No Space Linning
4 mm.
3.5
3.5, 4, 6 mm.
4 mm.
Wood Grain
8, 10, 1
- Smooth Surface
- Smooth Surface with Lining 3 inches
- Wood Grain Texture
- Smooth Surface with Lining 3 inches
Space Linning,
No Space Linning
Space Lining
4
4 mm.
- Smooth Surface
- Smooth Surface with Lining 3 inches
Space Linning,
No Space Linning
6-inch
Squared
Wood Gr
(Golden T
Decoretive Wall
6*, 8 mm
4-inch Sq
External Wall
8 mm. th
Backer Board
Squared Edge
Smooth Surface
Space Linning,
No Space Linning
8 mm.
Smooth Surface
Concealed Edge
8 mm.
No Space Linning
8 mm.
Squared Edge
Squared Edge
Squared Edge
Squared Edge
Squared Edge
- Smooth Surface
- Smooth Surface with Lining 4 inches
6
6
Smooth Surface
6
Smooth Surface
No Space Linning
16,
Floor Underlay
Floor
Squared Edge
Smooth Surface
Squared Edge
Smooth Surface
Weight
(kg./pc.)
Effective Area
(sqm./pc.)
60 x 240
7.6
0.70
7.6
0.70
120 x 240
15.2
0.35
60 x 120
4.4
1.40
60 x 240
8.7
0.70
120 x 120
8.7
0.70
120 x 240
17.4
0.35
60 x 120
6.6
1.40
26.1
0.35
34.8
0.35
40.2
0.30
8 mm.
120 x 240
43.5
0.35
12
120 x 240
52.2
0.35
120 x 240
69.6
0.35
87.0
0.28
16
6 mm.
8, 10, 12,
5 - 10 mm..
16 mm.
8 mm.
No Space Linning
Space Linning
10 mm.
2 side
120 x 300
Space Linning
Space Linning
120 x 240
10
Space Linning
6 mm.
4 side*
120 x 280
8 mm.
8-16 mm.
18
120 x 240
78.3
0.35
Wood Grain
60 x 120
5.0
1.40
3-inch SquareLining
60 x 120
5.1
1.40
Ventilated
60 x 120
4.2
1.40
60 x 120
4.9
1.40
60 x 120
5.1
1.40
4-inch SquareLining
8
6**
120 x 280
40.0
0.30
60 x 300
16.0
0.56
60 x 300
21.5
0.56
Smooth Surface
NEW
Tapered Edge
120 x 120
120 x 240
4 mm.
2-side T
8 mm. t
Series
Square Edge
4 mm.
Width x Length
(cm.)
Ventilated
hole
Thickness
(mm.)
8-12 mm.
* Made to order.
No Space Linning
16-18 mm.
24
**
Content
SCG SmartBoard Equipments for installation
SCG Self Drilling Point Screw 10 mm
Specially designed to suit with the work operated with Fiber cement
material safely, endure, and nice.
Longer life for rust or corrosion, because the material is made from
high-quality steel wires, can be used either external or internal.
Designed to provide the fin around the screw head which make the
screw head fully embedded in the panel automatically resulting nice
surface of work.
Containing size : 500 pieces / box
Specially designed to suit with the work operated with Fiber cement
material safely, endure, and nice.
Longer life for rust or corrosion, because the material is made from
high-quality steel wires, can be used either external or internal.
Specially designed to provide special drill end, which will not require
advance penetration, easily operated, and can drill rapidly into the steel,
its fin can core the panel allowing the screw head to be perfectly and
nicely embedded into the panel. The fin
will automatically break whenever the
steel is eventually penetrated.
Containing size : 500 pieces / box
This is the polyurethane material used to seal the joint, easily used,
and perfectly adhere to the surface of SmartBoard or any
construction materials such as fiber cement, concrete, brick,
roof tile, ceramic tile, aluminium, timber, glass.
Used as a joint sealant which can well prevent the leakage,
can be used in either external or internal of building.
Endure to the climate circumstance, and can be painted
over without altering the color shade.
Containing size : 310 ml/tube,
and 600 ml/foil tube
Ceilling Installation
3
3
4
5
7
8
23
9
9
11
14
15
Flooring Installation
16
19
Partition Installation
2.1 Space Lining Extream Partition Installation
2.2 Inner Space Lining Wall Installation
2.3 Inner Concealed Edge Wall Installation
20
20
21
22
6.
Jointing Substance
SCG SmartBoard
Set - Up Instruction
SCG Needle Point Screw
1
40 cm. 40 cm.
Level
Net
40 cm.
Plummet
Plummet
40 cm.
Drilling Machine
Hammer
Metal Frame
Cutter
(for 4mm thickness)
SCG SmartBoard
SCG SmartBoard
SCG SmartBoard
polyurethane joint sealant Acrylic Joint Compound Plaster Joint Compound
Structure steel
metal wall frame
Stainless trowel
(6 inch, 8 inch)
It is our recommendation not to do it on the panel which is over 5 meters long.In such case, technical discussion in details with us is needed.
22
: C-line frame
: SCG Needle Point Screw 23 mm.
: SCG SmartBoard Plaster Joint Compound, Sand Paper
Cutting Tool
Drilling Tool
: Drilling Machine
Grinding Tool
: Sandpaper, file
Set - Up Instruction
Installation Procedure
To cut with electric cutter : suitable for Smart Board in every size (3.5 - 12 mm.)
After the first coat of the plaster is set, apply the second
coat and polish with sand paper after it dries.
3
1.5 cm. 3 - 5 cm.
10 cm.
10 cm.
Use the cutter to rip on the set line several times until
the trace is 1 of 3 deep in SmartBoard thickness
21
Ceiling Installation
Space lining ceiling installation with wooden frame
:
:
:
:
Set - Up Instruction
Set - Up Instruction
60 .
Mark and Drill your desire point
60 .
3
Install hard wood frame size 1.5 x 3 inches. The distance
between frame is 60 x 60 cm. with straight surface,
no twisting
20 cm.
Suggestion : Hanging devices can be fixed to bath ceiling and wall by using the following accessories.
Tight the SmartBoard with SCG Needle point screw
23 mm. or 1 inch nail, 20 cm. apart.
Product
Application
Accessory
SCG SmartBoard
Ceiling
SCG SmartBoard
4 mm. thick
Ceiling
SCG SmartBoard
6 mm. thick
Ceiling
10
SCG SmartBoard
8 mm. thick
Wall
80
1.2 cm.
SCG Needle Point Screw 23 mm.
1.2 cm.
gap between screw 20 cm.
20 cm.
Recommendations
1. Use the table below to estimate the weight baring level of different thickness and usage of SmartBoard
2. When hanging heavy weight objects, it is advised to fix your object in the position that is on the studs, the maximum weight
stand will also vary depending on the strength of different studs.
20
Flooring Installation
: 1 8 .
1.5 10 . ,
: 8 - 12 .
Installation Procedure
Installation Process
:
:
:
:
()
60 cm.
40 cm.
5 cm.
60 cm.
4
1.2 cm.
1.2 cm.
1.2 cm.
1.2 cm.
gap between screw 20 cm.
20 cm.
20 cm.
Laminating material
6
1.2 cm.
Underlaying Foam
gap between
the edge 2 cm.
SCG SmartBoard
Leave 5 cm. gap from
an angle of the board
1.2 cm.
gap between screw 20 cm.
20 cm.
Suggestion
For fixing SCG SmartBoard with 1 concrete nail, be careful not to deepen the nail to reach reinforcing steel level.
Adjust the surface to be that same level before installation.
19
: galvanized iron metal ceiling frame (C-line) No. 24, minimum width of 38 mm.
: SCG needle point screw 23 millimeters in length
: SCG SmartBoard Acrylic Joint Compound, stainless trowel, square wooden-tray,
tape cloth, sand paper no.3
: 4-side Tapered Edge 6 mm. thick
SCG SmartBoard
Set-up Instruction
()
2
Bring next floor panel SCG SmartBoard to joint with.
80 cm.
40 cm.
8
Used Doubled minor studs
at the connection point
SCG Grumcrete
SCG SmartBoard
16 / 18 mm.
100 .
6
away from the edge 1.2 cm
40
cm
.
20 cm.
gap between screw
23 .
1.2 . 20 .
18
Troweling Instruction
Installation Method
Method for Smooth Plastering (only the SCG smartBoard Acrylic Joint Compound shall be used to
plaster the joint between the SmartBoards. All System and Opening works shall be completed prior
the plastering).
120 cm.
40 cm.
Check the top level of ceiling frame by the water, and the frame spacing must not higher than that designed.
15 cm.
5 .
400 mm.
max.
1.2 .
10
1.2 .
tape cloth
Space the floor panel SCG SmartBoard on the ceiling frame and fixed by SCG Self Drilling Screw 45 mm., with maximum 40 mm.
spacing, and 1.2 cm. distance from panel's edge.
20 cm.
15 cm.
11
12
28 cm.
17
Recommendation ;
The smooth-plastered SCG SmartBoard ceiling shall be installed in the area which will not directly contact to water, or the area
that tend to be vibrated by structure.
Set-up Instruction
Floor Installation
( )
:
:
:
:
75
45 .
16 - 18 .
Work preparation
1. Prepare the structure to support the floor panel SCG SmartBoard by allow the size and spacing of ceiling frame to support the
load safely as designed by the Engineer, or can choose the size and spacing of ceiling frame approximately from the Table.
2
Table 1 Spacing of stinger for the maximum safe load
121 cm.
60.5 cm.
121 cm.
60 cm.
Wall Angle
Thinkness (mm.)
Distance of support
(cm.)
Type of building
Live Load
(kg/m2)
16
40
House / Residence
150
40
Hotel / Dormitory
200
40
Office / Bank
250
40
School / University
300
30
400
30
500
18
Remark : Floor panel SCG SmartBoard shall not support point load higher than 100 kg, on 10 sq.cm. area.
Do not use in the area which always wet and moist.
2. The frame must provide at least 4.5 cm. width, in case that the steel frame is used there should be a rust protection at appropriate
level and suit to the environment and operating condition.
Cut SmartBoard into 60 x 120 cm. paint the surface
with old cement primer paint, Acrylic paint 2 times
for complete cover up of the original color, wait it dry.
Instruction :
in case need ceiling size 60 x 60 cm.enhance major studs 60.5 cm. in length with existing studs 121 x 60.5 cm.
16
Metal Stud
Connection Tools
SCG Smartboard
Set-Up instruction
Set-Up Instruction
()
curved studs
attach the studs to
structural element
100 cm.
3
3
4
drive screw into major studs
45 mm.
attach SmartBoard
to prepared studs
no more than 40 cm
no more than 40 cm
Remark : In case need to trowel connection point, you can do as the process for concealed ceiling.
Suggestion
SCG SmartBoard can be bend-installed by attach the board to the frame as the fixed radiance as follows:
Product
Thickness (mm.)
Lowest Possible
bended radiance
Space
between frame
Space between
connections
tools
2.00 m.
30 cm.
20 cm.
SmartBoard wall
10
4.00 m.
30 cm.
20 cm.
Product
Thickness
Minimum Redius
3.5 - 4 cm.
1.00 m.
6 mm.
1.50 cm.
SmartBoard Ceiling
40 cm.
15
20 cm.
Partition Installation
2.3 Inner Concealed Edge Wall Installation
Metal stud
Connection tool
Metal Stud
Connection Tools
Face Tool
SCG Smartboard
( 16 .)
:
:
:
:
Set-Up Instruction
Set-up Instruction
The set-up step is the same as Inner Space Lining wall Installation but the do not have to add the metal stud between the lining space
2
60
cm
.
2
Maximum distance
of frame 60 cm.
5 cm.
SCG SmartBoard
U 76 Galvanized Frame
SCG SmartBoard
60 cm.
1.2 cm.
20 cm.
45 mm.
75
20 cm.
Installation step
Step of concealed edge wall installation is the same as the concealed edge ceiling installation
light weight wall frame
1.2 cm.
8 - 12 .
32 . 20 .
1.2 . 16 .
45 .
5
tape
Fix Elephant cement corner by butterfly-wing plastichook, 37 mm. in length and SCG needle point screw
38 mm. in length to external corner
Suggestion
Concealed Edge wall : using advised only inner the building or dry area only.
14
The pole
2
2
SCG SmartBoard
SCG SmartBoard
SCG SmartBoard
polyurethane joint sealant
The pole
SCG SmartBoard
SCG Self Drilling
Screw 23 mm.
joint sealant
: 16 . 45 .
Detail for Insatallation
Metal studs
Ayara Heat reflection board
SCG SmartBoard
zinc No. 28
(for external used)
The pole
10 cm.
ground surface
Reinforce concrete beam
Make the gap for 0.5 - 1.0 cm at wall corner, and Seal
the joint between panel and frame with SCG SmartBoard
Polyurethane joint sealant.
Suggestion
For external partition installation, should consider about wind and other forces.
10 mm.
12 mm.
Less than 10
40
60
70
10 - 20
Not Recommend
40
50
20 - 30
Not Recommend
Not Recommend
40
More than 30
Not Recommend
Not Recommend
Not Recommend
Remark : length between and the thickness of SmartBoard, follow the engineer, who design the building.
13
10
5 cm.
:
:
:
:
1.2 cm.
20 cm.
Installation Method
10
9
SCG SmartBoard Wall
1
Determine the alignment of wall on the floor and ceiling
board.
4
Leave space of gap for 0.8 cm. (equal to pane's
thickness).
SCG SmartBoard U 76
Galvanized Frame
SCG SmartBoard C-74
Galvanized Frame
60 cm.
12
11
tape
76
Use the glue tape to cover the joint prior sealing the
joint by SCG SmartBoard Polyurethane Joint Sealant,
then peel the glue tape off, and left it dry.
280 .
280 cm.
Coat the prime coat for original cement for 1 layer, and
cover again by Acrylic Paint for at least 2 layers.
* Remark : In case that the SCG SmartBoard with 6 lining, golden teak style is used as real wall, the frame should be installed in every joint
along the length of panel in order to allow sealing of the joint by SCG SmartBoard Polyurethane joint sealant.
In case that the wall height is higher than 240 or 280 cm.
the SCG SmartBoard U 76 Galvanized Frame shall be
used to support on upper horizontal line at the panel level
(240-280 cm) as for supporting the panel jointing.
11
12
5 cm.
:
:
:
:
1.2 cm.
20 cm.
Installation Method
10
9
SCG SmartBoard Wall
1
Determine the alignment of wall on the floor and ceiling
board.
4
Leave space of gap for 0.8 cm. (equal to pane's
thickness).
SCG SmartBoard U 76
Galvanized Frame
SCG SmartBoard C-74
Galvanized Frame
60 cm.
12
11
tape
76
Use the glue tape to cover the joint prior sealing the
joint by SCG SmartBoard Polyurethane Joint Sealant,
then peel the glue tape off, and left it dry.
280 .
280 cm.
Coat the prime coat for original cement for 1 layer, and
cover again by Acrylic Paint for at least 2 layers.
* Remark : In case that the SCG SmartBoard with 6 lining, golden teak style is used as real wall, the frame should be installed in every joint
along the length of panel in order to allow sealing of the joint by SCG SmartBoard Polyurethane joint sealant.
In case that the wall height is higher than 240 or 280 cm.
the SCG SmartBoard U 76 Galvanized Frame shall be
used to support on upper horizontal line at the panel level
(240-280 cm) as for supporting the panel jointing.
11
12
The pole
2
2
SCG SmartBoard
SCG SmartBoard
SCG SmartBoard
polyurethane joint sealant
The pole
SCG SmartBoard
SCG Self Drilling
Screw 23 mm.
joint sealant
: 16 . 45 .
Detail for Insatallation
Metal studs
Ayara Heat reflection board
SCG SmartBoard
zinc No. 28
(for external used)
The pole
10 cm.
ground surface
Reinforce concrete beam
Make the gap for 0.5 - 1.0 cm at wall corner, and Seal
the joint between panel and frame with SCG SmartBoard
Polyurethane joint sealant.
Suggestion
For external partition installation, should consider about wind and other forces.
10 mm.
12 mm.
Less than 10
40
60
70
10 - 20
Not Recommend
40
50
20 - 30
Not Recommend
Not Recommend
40
More than 30
Not Recommend
Not Recommend
Not Recommend
Remark : length between and the thickness of SmartBoard, follow the engineer, who design the building.
13
10
Partition Installation
2.3 Inner Concealed Edge Wall Installation
Metal stud
Connection tool
Metal Stud
Connection Tools
Face Tool
SCG Smartboard
( 16 .)
:
:
:
:
Set-Up Instruction
Set-up Instruction
The set-up step is the same as Inner Space Lining wall Installation but the do not have to add the metal stud between the lining space
2
60
cm
.
2
Maximum distance
of frame 60 cm.
5 cm.
SCG SmartBoard
U 76 Galvanized Frame
SCG SmartBoard
60 cm.
1.2 cm.
20 cm.
45 mm.
75
20 cm.
Installation step
Step of concealed edge wall installation is the same as the concealed edge ceiling installation
light weight wall frame
1.2 cm.
8 - 12 .
32 . 20 .
1.2 . 16 .
45 .
5
tape
Fix Elephant cement corner by butterfly-wing plastichook, 37 mm. in length and SCG needle point screw
38 mm. in length to external corner
Suggestion
Concealed Edge wall : using advised only inner the building or dry area only.
14
Metal Stud
Connection Tools
SCG Smartboard
Set-Up instruction
Set-Up Instruction
()
curved studs
attach the studs to
structural element
100 cm.
3
3
4
drive screw into major studs
45 mm.
attach SmartBoard
to prepared studs
no more than 40 cm
no more than 40 cm
Remark : In case need to trowel connection point, you can do as the process for concealed ceiling.
Suggestion
SCG SmartBoard can be bend-installed by attach the board to the frame as the fixed radiance as follows:
Product
Thickness (mm.)
Lowest Possible
bended radiance
Space
between frame
Space between
connections
tools
2.00 m.
30 cm.
20 cm.
SmartBoard wall
10
4.00 m.
30 cm.
20 cm.
Product
Thickness
Minimum Redius
3.5 - 4 cm.
1.00 m.
6 mm.
1.50 cm.
SmartBoard Ceiling
40 cm.
15
20 cm.
Set-up Instruction
Floor Installation
( )
:
:
:
:
75
45 .
16 - 18 .
Work preparation
1. Prepare the structure to support the floor panel SCG SmartBoard by allow the size and spacing of ceiling frame to support the
load safely as designed by the Engineer, or can choose the size and spacing of ceiling frame approximately from the Table.
2
Table 1 Spacing of stinger for the maximum safe load
121 cm.
60.5 cm.
121 cm.
60 cm.
Wall Angle
Thinkness (mm.)
Distance of support
(cm.)
Type of building
Live Load
(kg/m2)
16
40
House / Residence
150
40
Hotel / Dormitory
200
40
Office / Bank
250
40
School / University
300
30
400
30
500
18
Remark : Floor panel SCG SmartBoard shall not support point load higher than 100 kg, on 10 sq.cm. area.
Do not use in the area which always wet and moist.
2. The frame must provide at least 4.5 cm. width, in case that the steel frame is used there should be a rust protection at appropriate
level and suit to the environment and operating condition.
Cut SmartBoard into 60 x 120 cm. paint the surface
with old cement primer paint, Acrylic paint 2 times
for complete cover up of the original color, wait it dry.
Instruction :
in case need ceiling size 60 x 60 cm.enhance major studs 60.5 cm. in length with existing studs 121 x 60.5 cm.
16
Troweling Instruction
Installation Method
Method for Smooth Plastering (only the SCG smartBoard Acrylic Joint Compound shall be used to
plaster the joint between the SmartBoards. All System and Opening works shall be completed prior
the plastering).
120 cm.
40 cm.
Check the top level of ceiling frame by the water, and the frame spacing must not higher than that designed.
15 cm.
5 .
400 mm.
max.
1.2 .
10
1.2 .
tape cloth
Space the floor panel SCG SmartBoard on the ceiling frame and fixed by SCG Self Drilling Screw 45 mm., with maximum 40 mm.
spacing, and 1.2 cm. distance from panel's edge.
20 cm.
15 cm.
11
12
28 cm.
17
Recommendation ;
The smooth-plastered SCG SmartBoard ceiling shall be installed in the area which will not directly contact to water, or the area
that tend to be vibrated by structure.
: galvanized iron metal ceiling frame (C-line) No. 24, minimum width of 38 mm.
: SCG needle point screw 23 millimeters in length
: SCG SmartBoard Acrylic Joint Compound, stainless trowel, square wooden-tray,
tape cloth, sand paper no.3
: 4-side Tapered Edge 6 mm. thick
SCG SmartBoard
Set-up Instruction
()
2
Bring next floor panel SCG SmartBoard to joint with.
80 cm.
40 cm.
8
Used Doubled minor studs
at the connection point
SCG Grumcrete
SCG SmartBoard
16 / 18 mm.
100 .
6
away from the edge 1.2 cm
40
cm
.
20 cm.
gap between screw
23 .
1.2 . 20 .
18
Flooring Installation
: 1 8 .
1.5 10 . ,
: 8 - 12 .
Installation Procedure
Installation Process
:
:
:
:
()
60 cm.
40 cm.
5 cm.
60 cm.
4
1.2 cm.
1.2 cm.
1.2 cm.
1.2 cm.
gap between screw 20 cm.
20 cm.
20 cm.
Laminating material
6
1.2 cm.
Underlaying Foam
gap between
the edge 2 cm.
SCG SmartBoard
Leave 5 cm. gap from
an angle of the board
1.2 cm.
gap between screw 20 cm.
20 cm.
Suggestion
For fixing SCG SmartBoard with 1 concrete nail, be careful not to deepen the nail to reach reinforcing steel level.
Adjust the surface to be that same level before installation.
19
Ceiling Installation
Space lining ceiling installation with wooden frame
:
:
:
:
Set - Up Instruction
Set - Up Instruction
60 .
Mark and Drill your desire point
60 .
3
Install hard wood frame size 1.5 x 3 inches. The distance
between frame is 60 x 60 cm. with straight surface,
no twisting
20 cm.
Suggestion : Hanging devices can be fixed to bath ceiling and wall by using the following accessories.
Tight the SmartBoard with SCG Needle point screw
23 mm. or 1 inch nail, 20 cm. apart.
Product
Application
Accessory
SCG SmartBoard
Ceiling
SCG SmartBoard
4 mm. thick
Ceiling
SCG SmartBoard
6 mm. thick
Ceiling
10
SCG SmartBoard
8 mm. thick
Wall
80
1.2 cm.
SCG Needle Point Screw 23 mm.
1.2 cm.
gap between screw 20 cm.
20 cm.
Recommendations
1. Use the table below to estimate the weight baring level of different thickness and usage of SmartBoard
2. When hanging heavy weight objects, it is advised to fix your object in the position that is on the studs, the maximum weight
stand will also vary depending on the strength of different studs.
20
: C-line frame
: SCG Needle Point Screw 23 mm.
: SCG SmartBoard Plaster Joint Compound, Sand Paper
Cutting Tool
Drilling Tool
: Drilling Machine
Grinding Tool
: Sandpaper, file
Set - Up Instruction
Installation Procedure
To cut with electric cutter : suitable for Smart Board in every size (3.5 - 12 mm.)
After the first coat of the plaster is set, apply the second
coat and polish with sand paper after it dries.
3
1.5 cm. 3 - 5 cm.
10 cm.
10 cm.
Use the cutter to rip on the set line several times until
the trace is 1 of 3 deep in SmartBoard thickness
21
6.
Jointing Substance
SCG SmartBoard
Set - Up Instruction
SCG Needle Point Screw
1
40 cm. 40 cm.
Level
Net
40 cm.
Plummet
Plummet
40 cm.
Drilling Machine
Hammer
Metal Frame
Cutter
(for 4mm thickness)
SCG SmartBoard
SCG SmartBoard
SCG SmartBoard
polyurethane joint sealant Acrylic Joint Compound Plaster Joint Compound
Structure steel
metal wall frame
Stainless trowel
(6 inch, 8 inch)
It is our recommendation not to do it on the panel which is over 5 meters long.In such case, technical discussion in details with us is needed.
22
Content
SCG SmartBoard Equipments for installation
SCG Self Drilling Point Screw 10 mm
Specially designed to suit with the work operated with Fiber cement
material safely, endure, and nice.
Longer life for rust or corrosion, because the material is made from
high-quality steel wires, can be used either external or internal.
Designed to provide the fin around the screw head which make the
screw head fully embedded in the panel automatically resulting nice
surface of work.
Containing size : 500 pieces / box
Specially designed to suit with the work operated with Fiber cement
material safely, endure, and nice.
Longer life for rust or corrosion, because the material is made from
high-quality steel wires, can be used either external or internal.
Specially designed to provide special drill end, which will not require
advance penetration, easily operated, and can drill rapidly into the steel,
its fin can core the panel allowing the screw head to be perfectly and
nicely embedded into the panel. The fin
will automatically break whenever the
steel is eventually penetrated.
Containing size : 500 pieces / box
This is the polyurethane material used to seal the joint, easily used,
and perfectly adhere to the surface of SmartBoard or any
construction materials such as fiber cement, concrete, brick,
roof tile, ceramic tile, aluminium, timber, glass.
Used as a joint sealant which can well prevent the leakage,
can be used in either external or internal of building.
Endure to the climate circumstance, and can be painted
over without altering the color shade.
Containing size : 310 ml/tube,
and 600 ml/foil tube
Ceilling Installation
3
3
4
5
7
8
23
9
9
11
14
15
Flooring Installation
16
19
Partition Installation
2.1 Space Lining Extream Partition Installation
2.2 Inner Space Lining Wall Installation
2.3 Inner Concealed Edge Wall Installation
20
20
21
22
Made from Elephant Portland Cement, Silica and special cellulose without asbestos which
make flexible with long lasting durability.
3.5, 4, 6
NEW
Firm
Water-Resistant
and Non-decay
4-side T
Premium
Resistant to Termites
Long lasting resistance to water, rain and sun without decaying (JIS Standard A5420)
SmartBoard is free.
6 mm. t
time that perform the lifting. Then use his leg power to lift
by holding at 30 cm distance from the panel edge of
SCG SmartBoard.
Termite cannot munch SCG SmartBoard because it is made from Elephant Portland Cement,
Silica and special cellulose all well blened together, which make termites and insects harmless
to SCG SmartBoard
Flexible and blended. No need for watering or moistening and with different bending radius for
different thickness.
4-side T
Special Properties
Squared
R = 4.0 m
R = 2.0 m
R = 1.5 m
Storing Tips
Flex
6 mm.
1.50 m. beding redius
8 mm.
2.0 m. beding redius
10 mm.
2.0 m. beding redius
Wood G
4 mm. th
Light weight,
easy to install and
customize your design
NEW
3-inch S
SCG SmartBoard walls can be designed to suit any rooms of your desire without any steel
beam reinforcement because they are 6 times lighter than traditional brick wall.
Traditional brick wall average
weights
180 kg./sqm.
SCG SmartBoard wall average
weights
30 kg./sqm.
4 mm. th
SCG SmartBoard has less than two times heat conductivity rate than asbestos fiber-cement
(ASTM C117 Standard) that reduces heat transfer from the under roof gap. Reduces in-house
temperature and saves energy.
Ventilate
4 mm. th
Application
Ventilate
4 mm. th
NEW
Internal Ceiling
Usage area
Any room that you want to prevent
problem from termites and moisture,
for example: Bathroom, Kitchen,
Storageroom, etc.
Ventilate
4 mm. th
Series
Squared Edge
Smooth Surface
Wood Grain
Ventilated
External Ceiling
Smooth Surface
Squared
Smooth Surface
Squared Edge
Surface
Ventilated
Wood Grain
Recommended
Thickness
3.5, 4, 6 mm.
Concealed Edge
6 mm.
Smooth Surface
Smooth Surface
Wood Grain Texture
Installation
System
Space Linning,
No Space Linning
4 mm.
3.5
3.5, 4, 6 mm.
4 mm.
Wood Grain
8, 10, 1
- Smooth Surface
- Smooth Surface with Lining 3 inches
- Wood Grain Texture
- Smooth Surface with Lining 3 inches
Space Linning,
No Space Linning
Space Lining
4
4 mm.
- Smooth Surface
- Smooth Surface with Lining 3 inches
Space Linning,
No Space Linning
6-inch
Squared
Wood Gr
(Golden T
Decoretive Wall
6*, 8 mm
4-inch Sq
External Wall
8 mm. th
Backer Board
Squared Edge
Smooth Surface
Space Linning,
No Space Linning
8 mm.
Smooth Surface
Concealed Edge
8 mm.
No Space Linning
8 mm.
Squared Edge
Squared Edge
Squared Edge
Squared Edge
Squared Edge
- Smooth Surface
- Smooth Surface with Lining 4 inches
6
6
Smooth Surface
6
Smooth Surface
No Space Linning
16,
Floor Underlay
Floor
Squared Edge
Smooth Surface
Squared Edge
Smooth Surface
Weight
(kg./pc.)
Effective Area
(sqm./pc.)
60 x 240
7.6
0.70
7.6
0.70
120 x 240
15.2
0.35
60 x 120
4.4
1.40
60 x 240
8.7
0.70
120 x 120
8.7
0.70
120 x 240
17.4
0.35
60 x 120
6.6
1.40
26.1
0.35
34.8
0.35
40.2
0.30
8 mm.
120 x 240
43.5
0.35
12
120 x 240
52.2
0.35
120 x 240
69.6
0.35
87.0
0.28
16
6 mm.
8, 10, 12,
5 - 10 mm..
16 mm.
8 mm.
No Space Linning
Space Linning
10 mm.
2 side
120 x 300
Space Linning
Space Linning
120 x 240
10
Space Linning
6 mm.
4 side*
120 x 280
8 mm.
8-16 mm.
18
120 x 240
78.3
0.35
Wood Grain
60 x 120
5.0
1.40
3-inch SquareLining
60 x 120
5.1
1.40
Ventilated
60 x 120
4.2
1.40
60 x 120
4.9
1.40
60 x 120
5.1
1.40
4-inch SquareLining
8
6**
120 x 280
40.0
0.30
60 x 300
16.0
0.56
60 x 300
21.5
0.56
Smooth Surface
NEW
Tapered Edge
120 x 120
120 x 240
4 mm.
2-side T
8 mm. t
Series
Square Edge
4 mm.
Width x Length
(cm.)
Ventilated
hole
Thickness
(mm.)
8-12 mm.
* Made to order.
No Space Linning
16-18 mm.
24
**
SCG SmartBaord
Caution
Do not use as any buildings structure or other purposes. The installation shall follow the Installation Manual and use only the standard equipments made
by producer.
Do not eat
First Aid
If the dust or any material debris accidentally entered the eye, do not scrub or crush. Clean with clean water several times, and consult the physician
immediately.
Verify that all methods are following the most update of Installation Manual of Products
Installation Manual of Products is always updated. The designer, construction supervisor, and installer shall verify that all methods being used are following
the most update of Installation Manual of Products. They can confirm by the website : www.siamfibrecement.com
0610
Fiber Cement
Board
Non Asbestos