Documente Academic
Documente Profesional
Documente Cultură
1. Equipment Introduction
1.1 System Overview
Abbreviated Name
Full Name
CCUC
ASPB
ADLE
VDSE
EIUA
16 Fe Electric Port
EIUD
4 Fe (fiber)+ 4 Ge(Combo)
PAIA
AC power board
PAIB
PDIA
DC power board
FCBA
Daughter
Board
Port
Function
UP2A
UP2C
ASDA/ASDM
Note:
1. For PAIB card, it support AC and DC at the same time, but DC is the backup for AC, by nature,
DC does not work. Only when the AC power on first and suddenly down, system will drive DC
to work.
2. For PAIB card, the DC connection is designed to connect to Battery and charge the battery by
DSLAM himself. It is not recommendatory to connect the DC connection to other kind of DC
power, otherwise it is likely to destroy the power card of DSLAM.
Grounding Condition
Protective Unit
onsite engineering and the subsequent maintenance; Before routing the AC power cable,
ensure that the switch of the AC PDU is set to be OFF.
9. Before routing the user cables, make the label for the cable and when the service is
enabled in the future the cable side terminal block must be installed with the protective
unit.
10. When deploy the Optical cable and Optical Fiber: Make label; Only the qualified
personnel are allowed to splice the optical fiber; When handling optical fibers do not
stand close to or look into the optical fiber outlet with unproteced eyes; The optical fiber
in the cabinet should be protected with a spiral rube; The bending radius of the optical
fiber should be more than 20 times the cable diameter, in generally the bending radius of
the optical fiber is greater than or equal to 40mm.
11. Check the cabinet carefully according with the "Check list " of the installation guide.
12. Power on the service device only when the input AC voltage is in the normal range:
100V to 240V.
13. If the cabling apertures at the bottom of the cabinet or battery compartment are the
sleeves, cover the sealing material(such as sealing mud) onto the cabling apertures at the
bottom of the cabinet; and if the cabling apertures at the bottom of cabinet are the PG
connectors, fasten the PG connectors properly.
State
| ID
Type
State
---------------------------------------------------------------------------0
FAN
H831PMU
6
8
Normal
H831VESC
| 5
| 7
| 9
10 -
| 11
12 -
| 13
14 -
| 15
Normal
Normal
---------------------------------------------------------------------------MA5616(config)#interface emu 1
MA5616(config-if-h831vesc-1)# esc digital 0 available-level low-level name hightemp
MA5616(config-if-h831vesc-1)# esc digital 1 available-level low-level name door
MA5616(config-if-h831vesc-1)# esc digital 2 available-level low-level name arrester
MA5616(config-if-h831vesc-1)# display esc alarm
EMU ID: 1
---------------------------------------------------------------------------DigitalID
Name
State
| DigitalID Name
State
hightemp
Normal
Alarm
arrester
Normal
1
3
Door
Wiring
----------------------------------------------------------------------------
Normal
(config)#display emu
EMU parameter
---------------------------------------------------------------------------ID Type
State
| ID Type
State
---------------------------------------------------------------------------0
FAN
normal
| 1
2 | 3 4 | 5 6 | 7 8 | 9 10 | 11 12 | 13 14 | 15 16 | 17 18 | 19 20 | 21 22 | 23 24 | 25 26 | 27 28 | 29 30 | 31 32 | 33 (config)#emu add 1 Power4830L 0 0
(config-if-power4830l-1)#power outside-digital 3 available-level low-level name Arrester
(config-if-power4830l-1)#power outside-digital 4 available-level high-level name smoke
(config-if-power4830l-1)#power outside-digital 5 available-level low-level name fan
Service-Slot1
Service-Slot2
Service-Slot3
Service-Slot4
PPPOE
0-255
0-63
64-127
128-171
172-255
IPTV
256-511
256-319
320-383
384-447
448-511
VOIP
512-767
512-577
578-639
640-703
704-767
IPOE
768~999
IPTV
VOIP
IPOE
ADSL (pvc)
8/35
8/36
8/37
8/38
VDSL (uservlan)
35
36
37
38
FE
35
36
37
38
(uservlan)
CCUC
ControlCard
Slot1
VDSE
VDSL
Slot2
ADLE
ADSL
Slot3
EIUA
FE
Slot4
ASPB
POTS
Slot5
PAIB
Power card
Note: It is not recommendatory to deploy the ADSL and VDSL at the same DSLAM, because
there is crossing talking between VDSL and ADSL signal. And if there must configure ADSL and
VDSL at the same time, please set the ADSL and VDSL cards far, for example, ADSL slot1 and
VDSL slot4, and also the Copper line cable between ADSL and VDSL better to be isolated.
1.3.4.2 IPTV
MA5616(config)#vlan service profile profile-id 2 profile-name IPTV
MA5616(config-vlan-srvprof-2)# Anti-macspoofing enable
MA5616(config-vlan-srvprof-2)# pitp disable
MA5616(config-vlan-srvprof-2)# dhcp option82 disable
MA5616(config-vlan-srvprof-2)# commit
MA5616(config-vlan-srvprof-2)# quit
Note: Because now VASC not require DHCP option82 feature on DSLAM, so here we disable
dhcp option82 at DSLAM.
1.3.4.3 VOIP
1.3.4.4 IPOE
MA5616(config)#vlan service-profile profile-id 4 profile-name IPOE
MA5616(config-vlan-srvprof-4)# Anti-macspoofing disable
MA5616(config-vlan-srvprof-4)# pitp disable
MA5616(config-vlan-srvprof-4)# dhcp option82 disable
MA5616(config-vlan-srvprof-4)# commit
MA5616(config-vlan-srvprof-4)# quit
Note: For IPOE service, we can not enable Anti-Macspoofing feature at IPOE VLAN, otherwise
all of the static IPOE service will be down.
In short, if VNPT require to protect the POTS card, and let Broad-band cards down after AC
down, please enable such feature, otherwise please undo this feature.
The above is designed for DSL access, ADSL & VDSL, and the following is for FE access:
Case1:
If MA5616 cascading under MA5600, MA5616 should set the DSLAM IGMP version to be as IGMP
V2, because the current MA5600 work as IGMP V2.
MA5616(config)#multicast-vlan 99
MA5616(config-mvlan99)# igmp version v2
And MA5600 should configure the GE port who connect with the MA5616 to be IPTV cascading
port: MA5600(config)#igmp cascade-port frameid/slotid/portid quickleave disable
Case2:
If MA5616 connect to UPE or LSW, but UPE or LSW run the IGMP V2. In this case, MA5616 also
need set the IGMP version to be IGMP V2.
Note: MA5616 work as IGMP V3 by default.
Service-Slot1
Service-Slot2
Service-Slot3
Service-Slot4
PPPOE
0-255
0-63
64-127
128-171
172-255
IPTV
256-511
256-319
320-383
384-447
448-511
VOIP
512-767
512-577
578-639
640-703
704-767
IPOE
768~999
PVC : 8/35
PPPOE
IPTV
VOIP
IPOE
ADSL (pvc)
8/35
8/36
8/37
8/38
VDSL (uservlan)
35
36
37
38
FE
35
36
37
38
(uservlan)
Traffic Table: 11
Range
Service-Slot1
Service-Slot2
Service-Slot3
Service-Slot4
PPPOE
0-255
0-63
64-127
128-171
172-255
IPTV
256-511
256-319
320-383
384-447
448-511
VOIP
512-767
512-577
578-639
640-703
704-767
IPOE
768~999
PPPOE
IPTV
VOIP
IPOE
ADSL (pvc)
8/35
8/36
8/37
8/38
VDSL (uservlan)
35
36
37
38
FE
35
36
37
38
(uservlan)
Range
Service-Slot1
Service-Slot2
Service-Slot3
Service-Slot4
PPPOE
0-255
0-63
64-127
128-171
172-255
IPTV
256-511
256-319
320-383
384-447
448-511
VOIP
512-767
512-577
578-639
640-703
704-767
IPOE
768~999
Service-Slot1
Service-Slot2
Service-Slot3
Service-Slot4
PPPOE
0-255
0-63
64-127
128-171
172-255
IPTV
256-511
256-319
320-383
384-447
448-511
VOIP
512-767
512-577
578-639
640-703
704-767
IPOE
768~999
PPPOE
IPTV
VOIP
IPOE
ADSL (pvc)
8/35
8/36
8/37
8/38
VDSL (uservlan)
35
36
37
38
FE
35
36
37
38
(uservlan)
Service-port ID as following:
Range
Service-Slot1
Service-Slot2
Service-Slot3
Service-Slot4
PPPOE
0-255
0-63
64-127
128-171
172-255
IPTV
256-511
256-319
320-383
384-447
448-511
VOIP
512-767
512-577
578-639
640-703
704-767
IPOE
768~999
IPTV
VOIP
IPOE
ADSL (pvc)
8/35
8/36
8/37
8/38
VDSL (uservlan)
35
36
37
38
FE
35
36
37
38
(uservlan)
Name: 17A_B8-11_(SNR6-slow-INP2)
: Enable
: Enable
: AdaptAtStartup
: AdaptAtStartup
: 60
: 0
: 300
: 60
: 0
: 300
: 1650,1020
: 1650,615
: 0,0
: 0,0
: Enable
: 0
: 0
: 0
: 0
: Auto
: not allowed
: not allowed
L0 time(second)
: 255
L2 time(second)
: 30
L3 time(second)
: 255
: 3
: 9
<defmode>
G.993.2 profile
: Profile17a
: AnnexB998ADE17-M2x-A(B8-11)
: Unused
: 145
: 145
: ADLU-32/EU-32
: Disable
: Disable
: FreeRun
: 0
: 0
: 0
: 3
: 0
: 0
: 0
: 65535
: 0
: 0
: 0
: 0
: 0
: 65535
: 0
: 0
: 0
------------------------------------------------------------------------------
Name: 33M/10M(Down/Up)
: Both
: TwoSymbols
: TwoSymbols
: 16
: 16
: 64
: 34837
: 64
: 64
: 10557
: 0
: 0
: 0
: 0
: Disable
: Disable
: Disable
: 8
: 8
------------------------------------------------------------------------------
VDSL (PTM)
Overhead = INT((L+4)/64)+4+MOD((L+4),64)/64
Packet size(L)
Overhead
total size
PTM efficiency
64
5.0625
69.0625
92.67%
128
6.0625
134.0625
95.48%
256
8.0625
264.0625
96.95%
512
12.0625
524.0625
97.70%
1024
20.0625
1044.0625
98.08%
1500
27.5
1527.5
98.20%
And if we need change the Line Speed, we can create the different Channel-Profile to define
the speed but can reuse the same line-profile(10), for example, now we need create the 40M
Down and 10M up, so we can define one more channel-profile who define the 40M/10M speed
and reuse the old Line-profile(ID:10).
MA5616(config)#display vdsl channel-profile 40
-----------------------------------------------------------------------------Profile index: 40
Name: 40M/10M(Down/Up)
: Both
: TwoSymbols
: TwoSymbols
: 16
: 16
: 64
: 40960
: 64
: 64
: 10240
: 0
: 0
: 0
: 0
: Disable
: Disable
: Disable
: 8
: 8
------------------------------------------------------------------------------
>
>
Transmission mode:
>
0: Custom
>
1: All (G.992.1~5,T1.413,G.993.2)
>
2: Full rate(G.992.1/3/5,T1.413,G.993.2)
>
3: G.DMT (G.992.1/3/5,G.993.2)
>
4: G.HS (G.992.1~5,G.993.2)
>
5: ADSL (G.992.1~5,T1.413)
>
6: VDSL (G.993.2)
>
>
>
>
>
>
>
>
>
>
>
>
>
Will you set ADSL tone blackout configuration parameter? (y/n) [n]:
>
Will you set VDSL tone blackout configuration parameter? (y/n) [n]:
>
>
>
1-defmode
>
>
1-defmode
>
Please select
>
G.993.2 profile:
>
1-Profile8a
2-Profile8b
3-Profile8c
4-Profile8d
>
5-Profile12a
6-Profile12b
7-Profile17a
8-Profile30a
>
>
>
1-AnnexA998-D-32
2-AnnexA998-D-64
>
3-AnnexBHPE17-M1(B7-7)
4-AnnexB997E17-M2x-A(B7-9)
>
5-AnnexB998E17-M2x-NUS0(B8-8)
6-AnnexB998E17-M2x-NUS0-M(B8-9)
>
7-AnnexB998ADE17-M2x-NUS0-M(B8-10)
8-AnnexB998ADE17-M2x-B(B8-12)
>
9-AnnexB998ADE17-M2x-A(B8-11)
10-AnnexA998-D-48
>
11-AnnexA998-D-128
>
>
>
>
>
2-Modify
[3]:2
[1]:
>
>
Will you set PSD mask value downstream parameter? (y/n) [n]:
>
Will you set PSD mask value upstream parameter? (y/n) [n]:
>
Will you set Upstream PSD mask selection parameter? (y/n) [n]:
>
>
>
1-defmode
>
2-Modify
>
>
>
>
[3]:
>
>
Will you set the minimum impulse noise protection? (y/n) [n]:y
>
>
1-noProtection
2-halfSymbol
3-singleSymbol
4-twoSymbols
>
5-threeSymbols
6-fourSymbols
7-fiveSymbols
8-sixSymbols
>
9-sevenSymbols
10-eightSymbols
11-nineSymbols
12-tenSymbols
>
13-elevenSymbols
14-twelveSymbols
15-thirteenSymbols 16-fourteenSymbols
>
17-fifteenSymbols 18-sixteenSymbols
>
>
>
1-noProtection
2-halfSymbol
3-singleSymbol
4-twoSymbols
>
5-threeSymbols
6-fourSymbols
7-fiveSymbols
8-sixSymbols
>
9-sevenSymbols
10-eightSymbols
11-nineSymbols
12-tenSymbols
>
13-elevenSymbols
14-twelveSymbols
15-thirteenSymbols 16-fourteenSymbols
>
17-fifteenSymbols 18-sixteenSymbols
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
Setp2 : Check the VDSL port active mode, ATM or PTM, if not PTM, please check the
Modem setting, it should be set to be PTM mode.
Service-Slot1
Service-Slot2
Service-Slot3
Service-Slot4
PPPOE
0-255
0-63
64-127
128-171
172-255
IPTV
256-511
256-319
320-383
384-447
448-511
VOIP
512-767
512-577
578-639
640-703
704-767
IPOE
768~999
PPPOE
IPTV
VOIP
IPOE
ADSL (pvc)
8/35
8/36
8/37
8/38
VDSL (uservlan)
35
36
37
38
FE
35
36
37
38
(uservlan)
Range
Service-Slot1
Service-Slot2
Service-Slot3
Service-Slot4
PPPOE
0-255
0-63
64-127
128-171
172-255
IPTV
256-511
256-319
320-383
384-447
448-511
VOIP
512-767
512-577
578-639
640-703
704-767
IPOE
768~999
User Vlan: 36 should be set at VDSL CPE, on the IPTV bridge channel, for all of the CPE can be set
to be the same mode, for example, every CPE set the IPTV Bridge channel to be uservlan 36.
PPPOE
IPTV
VOIP
IPOE
ADSL (pvc)
8/35
8/36
8/37
8/38
VDSL (uservlan)
35
36
37
38
FE
35
36
37
38
(uservlan)
Service-Slot1
Service-Slot2
Service-Slot3
Service-Slot4
PPPOE
0-255
0-63
64-127
128-171
172-255
IPTV
256-511
256-319
320-383
384-447
448-511
VOIP
512-767
IPOE
768~999
512-577
578-639
640-703
704-767
Service-Slot1
Service-Slot2
Service-Slot3
Service-Slot4
PPPOE
0-255
0-63
64-127
128-171
172-255
IPTV
256-511
256-319
320-383
384-447
448-511
VOIP
512-767
512-577
578-639
640-703
704-767
IPOE
768~999
User Vlan: 37 should be set at VDSL CPE, on the IPTV bridge channel, for all of the CPE can be set
to be the same mode, for example, every CPE set the IPTV Bridge channel to be uservlan 37.
PPPOE
IPTV
VOIP
IPOE
ADSL (pvc)
8/35
8/36
8/37
8/38
VDSL (uservlan)
35
36
37
38
FE
35
36
37
38
(uservlan)
Setp2 : Check the VDSL port active mode, ATM or PTM, if not PTM, please check the
Modem setting, it should be set to be PTM mode.
Range
Service-Slot1
Service-Slot2
Service-Slot3
Service-Slot4
PPPOE
0-255
0-63
64-127
128-171
172-255
IPTV
256-511
256-319
320-383
384-447
448-511
VOIP
512-767
IPOE
768~999
512-577
578-639
PPPOE
IPTV
VOIP
IPOE
ADSL (pvc)
8/35
8/36
8/37
8/38
VDSL (uservlan)
35
36
37
38
FE
35
36
37
38
(uservlan)
640-703
704-767
Note: Make sure that DSLAM can ping Gateway and IMS, otherwise please check the Routing
from DSLAM to Gateway and IMS.
MA5616(config)#voip
MA5616(config-voip)#ip address media 10.99.16.2 10.99.16.1
MA5616(config-voip)#ip address signaling 10.99.16.2
MA5616(config-voip)#quit
MA5616(config)#display protocol support
System support SIP protocol
Note: DSLAM support 2 mode, if the current mode is H248, we should use command protocol
support sip to set the DSLAM mode to be SIP and restart the DSLAM.
MA5616(config)#interface sip 0
MA5616(config-sip0)#if-sip attribute basic media-ip 10.99.16.2 signal-ip 10.99.16.2 signal-port
5060 home-domain ims.vnpt.vn
MA5616(config-sip0)#if-sip attribute basic primary-proxy-ip1 113.171.225.6 primary-proxy-port
5060
MA5616(config-sip0)#reset
//After a while, check the SIP interface status, if normal it should be Up, otherwise please help
contact VTN expert for support.
MA5616(config-sip0)#display if-sip attribute running 0
MA5616(config-sip0)#quit
MA5616(config)# esl user
MA5616(config-esl user)# sippstnuser add 0/4/1 0 telno +84432000201
MA5616(config-esl user)#sippstnuser auth set 0/4/1 telno +84432000201
84432000201 password-mode password 84432000201
MA5616(config-esl user)#quit
auth-username
//After a while, please check phone status, if can not be normal after 5 mins, please help capture
the SIP packets between DSLAM and IMS with wireshark or ethereal software and send to VTN
expert for trouble shooting.
Range
Service-Slot1
Service-Slot2
Service-Slot3
Service-Slot4
PPPOE
0-255
0-63
64-127
128-171
172-255
IPTV
256-511
256-319
320-383
384-447
448-511
VOIP
512-767
512-577
578-639
640-703
704-767
IPOE
768~999
PPPOE
IPTV
VOIP
IPOE
ADSL (pvc)
8/35
8/36
8/37
8/38
VDSL (uservlan)
35
36
37
38
FE
35
36
37
38
(uservlan)
Range
Service-Slot1
Service-Slot2
Service-Slot3
Service-Slot4
PPPOE
0-255
0-63
64-127
128-171
172-255
IPTV
256-511
256-319
320-383
384-447
448-511
VOIP
512-767
512-577
578-639
640-703
704-767
IPOE
768~999
User Vlan: 36 should be set at VDSL CPE, on the IPTV bridge channel, for all of the CPE can be set
to be the same mode, for example, every CPE set the IPTV Bridge channel to be uservlan 36.
PPPOE
IPTV
VOIP
IPOE
ADSL (pvc)
8/35
8/36
8/37
8/38
VDSL (uservlan)
35
36
37
38
FE
35
36
37
38
(uservlan)
Service-Slot1
Service-Slot2
Service-Slot3
Service-Slot4
PPPOE
0-255
0-63
64-127
128-171
172-255
IPTV
256-511
256-319
320-383
384-447
448-511
VOIP
512-767
512-577
578-639
640-703
704-767
IPOE
768~999
User Vlan: 37 should be set at FE CPE, on the IPTV bridge channel, for all of the CPE can be set to
be the same mode, for example, every CPE set the IPTV Bridge channel to be uservlan 37.
PPPOE
IPTV
VOIP
IPOE
ADSL (pvc)
8/35
8/36
8/37
8/38
VDSL (uservlan)
35
36
37
38
FE
35
36
37
38
(uservlan)
Traffic-Table: 120
Service-Slot1
Service-Slot2
Service-Slot3
Service-Slot4
PPPOE
0-255
0-63
64-127
128-171
172-255
IPTV
256-511
256-319
320-383
384-447
448-511
VOIP
512-767
512-577
578-639
640-703
704-767
IPOE
768~999
PPPOE
IPTV
VOIP
IPOE
ADSL (pvc)
8/35
8/36
8/37
8/38
VDSL (uservlan)
35
36
37
38
FE
35
36
37
38
(uservlan)
Traffic Table: 80
Note:
1. This feature is just for PPPOE and DHCP service, can not be used for IPOE service, otherwise
the IPOE service will be down.
2. After use the feature at PPPOE and DHCP vlan, please use another command to check the
MAC address for this 2 Vlan: display security bind mac
If there is one user port have too much protocol packet, system can detect and discard
all of the protocol packets of that port but the common data packet can be transfer
still.
And if this port recovers, system will release this port and begin to deal with the
protocol packet of that port again.
MA5616(config)#ring check { enable | disable }
By default, the ring check function is disabled.
When the Ring Check feature is enabled in the device, the device sends 16 Ring Check
packets (proprietary BPDU packets) to the subscriber port per second. The device sends
the Ring Check packets to only the traffic stream that is in the Up state.
Ring check mechanism:
If the MA5616 receives the private ring check packet from a user port, it blocks the user
port and sends the matched alarm.
If the device receives Ring Check packet from a user port, it determines whether the
root bridge in the packet is the same as that in the device. If they are the same, the
device blocks the user port and sends the matched alarm.
If the device received the private Ring Check packet from the upstream port, it
determines whether the packet is sent from the root bridge. If the packet is sent from
the root bridge, the device blocks the user port and sends the matched alarm.
huawei(config)#security mac-filter
{ mac_addr<P><XXXX-XXXX-XXXX> }:1010-1010-3020
Command:
security mac-filter 1010-1010-3020
Note: System can configure 4 different Security MAC-Filter in total.
Note: In this way, DSLAM can check the port status, it can work or not, before deploy the real
service.
The callee can hear the test tone from the phone, and can feedback the quality by
press button * to report to DSLAM good quality and other button not good.
Note: In this way, DSLAM can check the port status, it can work or not, before deploy the real
service.