Documente Academic
Documente Profesional
Documente Cultură
Figure is hypnosis, electrotherapy circuit diagram of dual-use device, the main part of the blocking oscillator is
a feedback inductor, L3 by the step-up transformer T secondary double peak pulse output of 60V, for
radiotherapy of human acupuncture points used. At the same time issued a similar piezoelectric ceramics
driven sound of rain for the use of hypnosis. Adjustment potentiometer RP1, you can change the oscillation
frequency of oscillator circuit. General electrical stimulation, the frequency per minute, preferably between 120
to 200; hypnosis frequency of about 50 per minute is better. Adjustment potentiometer RP1, you can change
the output pulse amplitude and volume of the piezoelectric film made.
Pulse transformer selected cross-section 6 8mm the E type ferrite core transformer is also available in the Etype silicon transistor radio cores substitution, but the effect is less. L1 0.25mm in diameter around the 80
turns of enameled wire, L2 around 280 turns, diameter 0.09mm, 0.07mm diameter and the output coil wound
with 2200 L3 turn, each of the winding insulation, and indicate the end of the same name
Figure 1 shows the circuit, when the OP amplifier A as the current is inputed
into amplifier and visible load resistance R of CT is 0. This circuit can
significantly improve the low frequency characteristics. When the gain of lowfrequency domain needs to be compensated, the feedback capacitor CF can be
inserted into . In this circuit, to prevent the OP amplifier A becoming into openloop in the DC area and composing of the DC open-loop (fc 1.6Hz) in the noninverting integrator A2 (commonly known as the DC servo circuit), this circuit's
output voltage v is: If RF = 50k, then i = 10mA, which can be transformed as
1V. The value of this capacitor CF is decided by the CF characteristics of shortcircuit, so it can be obtained by the experiment. The 47pF capacitor parallelling
with FR is to suppress high-frequency characteristics, no special basis.
The home electrotherapy has the the output frequency function of more than
ten-speed automatic loop ransformation .The pulse intensity and the speed of
the frequency conversion can be adjusted freely.It outputs a broad
spectrum.The broad spectrum is very suitable to be as the massor .And it can
dissipate fatigue and to be as an adjuvant treatment of some common
diseases. The circuit consists of the variable frequency pulse oscillator, the
oscillation frequency conversion controller and the pulse output circuit.
The picture shows sine wave oscillating circuit which is composed of MJM5534.
This a kind of wien bridge sine wave oscillating circuit. If R1=R2=R,C1=C2=C,
then oscillating frequency is 1/(2RC). Wien bridge will make amplitude stay
stable, so there is great distortion. But when it is converted to low frequency
which is below 10HZ, the amplitude will be stable in short time. According to
the component parameter in the picture, by adjusting RP1's resistance value,
output voltage's effective value is 5V. By changing C1's value, its distortion rate
will be 0.7%-0.9% in the frequency range of 10HZ-100KHZ. If output voltage's
effective value is adjusted to 3V, then the distortion rate can be reduced to
0.1%.
There are many different types of electronic treatment in the medical device
market.They are said that they have a special effect to certain diseases.The
price is also not cheap. In fact, most of them are nothing more than some
electronic treatment devices which can output some pulses .They may have
the effect to some diseases in accordance with different frequencies of the
output pulse waveform.It is the home points electrotherapy shown as the chart.
The whole circuit is mainly composed of a Schmitt trigger CD40106 six.The
ultra-low-frequency multivibrator oscillation consists of the Dl, Rl, VDl and C1.
The oscillation frequency is 0.5 ~ 5Hz. It is regulated by RPl.
The electric biological wave physiotherapy circuit is shown as the chart.It can
generate the electric signals of various composite frequency.It is good for the
drugs absorption for the patients.It can also act on the human acupoint to do
the treatment
As the figure 16-20 shows, this multifunction electronic acupoint detection and
therapeutic equipment circuit is composed of the acupoint detection circuit, the
timer, the pulse generator and the amplifier output stage, it can be used in the
acupoint detection and the no needle electrotherapy applications. The acupoint
detector is composed of the VT1VT2R1R4RP1C1VT3 and T1.etc,
actually it is a audio oscillator. The timing circuit is composed of the IC1(555),
R4RP2 and C3. The astable multivibrator is composed of the IC2 and
RP4R8D3D4RP3, C4, the oscillation frequency f=1.44/
(RP4+RP3+R8)C4, the oscillation frequency and the duty ratio are adjustable.
The machine is a physical therapy apparatus in treatment for low frequency modulation type DC, circuit shown
in Figure. DL1 rectified by the bridge by the filter output of about 156V DC high voltage, the load (output
adjustment potentiometer RP) termination under low frequency modulation control VT6. VT1, VT2
composition of low-frequency multivibrator, the VT3, VT4, VT5 amplified drive VT6 (DD01B) modulation of
the output DC current. (VT1, VT3 are with the 9013 tube, VT2, VT4 are with the 9012 tube, VT5 to 3DK9Ctube) output, - were then treated with electrodes to be placed in the patient treatment site. According to the
degree required for treatment and patients with RP select the appropriate tolerate current, current intensity
range from the current meter with two PA table instructions. Use, should be adjusted so that the current RP
gradually increased from zero; the end of the current transfer will be zero and then remove the electrode. If the
electronic enthusiasts interested in super stimulation current therapy, can be made according to the circuit
using a single instrument.