Documente Academic
Documente Profesional
Documente Cultură
MGS3600-24F_V1.00(AACA.0)C0
Release Note/Manual Supplement
Date:
This document describes the features in the MGS3600-24F product for its
MGS3600-24F_V1.00(AACA.0)C0 release.
Support Platforms:
ZyXEL MGS3600-24F_V1.00(AACA.0)C0 supports models: ZyXEL MGS3600-24F
Version:
OS Version: MGS3600-24F_V1.00(AACA.0)C0 | 11/02/2012
BootBase Version: V1.00 | 11/02/2011
Main Features:
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
25.
IPv6 Management/host
IEEE 802.3 10Base-T Ethernet
IEEE 802.3u 100Base-Tx Ethernet
IEEE 802.ab 1000Base-T Ethernet
IEEE 802.3z 1000Base-SX/LX Ethernet
IEEE 802.3x flow control
IEEE 802.1d spanning tree protocol
IEEE 802.1w rapid spanning tree protocol
IEEE 802.1s multiple spanning tree protocol
IEEE 802.1p class of service, priority protocols
IEEE 802.1Q VLAN tagging
IEEE 802.1x port authentication
IEEE 802.3ad LACP aggregation
IEEE 802.3ah Ethernet OAM
IEEE 802.1ag Ethernet CFM
ITU-T Y.1731 Performance Monitoring
ITU-T G.8031 Ethernet Linear Protection
ITU-T G.8032 Ethernet Ring Protection
Flow Control
SFP Read Information
Cable Diagnostic
MAC entry search
Trunking Failover
Support ACL and QCL for traffic filtering
IEEE 802.1p with 8 hardware priority queues per port for different types of
traffic
26.
27.
28.
29.
30.
31.
32.
33.
34.
35.
36.
37.
38.
39.
40.
41.
42.
43.
44.
45.
46.
47.
48.
49.
50.
51.
52.
53.
54.
55.
56.
57.
58.
59.
60.
61.
62.
63.
64.
65.
66.
67.
68.
69.
Bug Fix:
1. Bug 13433 V1.22 SNMPc:get mib file will stop on atIfindex OID
2. Bug 13210 fix LACP WEB information incorrect problem
Known Issue:
1.
No
Limitation of Settings:
Firmware Upgrade:
The MGS3600-24F uses HTTP to upgrade firmware in run-time through its built-in HTTP
server. You can use any Browser (for example IE Windows) to upgrade MGS3600-24F. The
upgrade procedure is as follows:
Firmware Upgrade
This page facilitates an update of the firmware controlling the
Switch.
Web Interface
To configure a Firmware Upgrade Configuration in the web interface:
1. Chick Browser to select firmware in you device.
2. Click Upload.
Figure 5-2.1:
Parameter description:
Browse :
Click the Browse... button to search the Firmware URL and filename.
Upload:
Click the Upload button then the switch will start to upload the firmware from
firmware stored location PC or Server.
Web Interface
To configure a Firmware Selection in the web interface:
1. Chick Activate Alternate Image.
2. Click yes to complete firmware selection.
Figure 5-2.2:
Parameter description:
Cancel:
Cancel activating the backup image. Navigates away from this page.
Image :
The flash index name of the firmware image. The name of primary (preferred)
image is image, the alternate image is named image.bk.
Version :
The version of the firmware image.
Date :
The date where the firmware was produced.
NOTE:
1. In case the active firmware image is the alternate
image, only the "Active Image" table is shown. In this
case, the Activate Alternate Image button is also
disabled.
2. If the alternate image is active (due to a corruption of the
primary image or by manual intervention), uploading a new
firmware image to the device will automatically use the
primary image slot and activate this.
3. The firmware version and date information may be empty for
older firmware releases. This does not constitute an error.