Documente Academic
Documente Profesional
Documente Cultură
User Manual
Please read all information in this manual thoroughly. Familiarize yourself with the capabilities and the usage of your
appliance before attempting to operate or maintain this unit. Taking a minute to do this now will help to prevent any
damages or loss in the future.
Keep this manual handy as a reference for operating procedures and safety information.
Do not insert any kind of irrelevant objects into this device through the openings as they may touch dangerous
voltage points that could result in the fire or electric shock.
Avoid placing this unit near the liquids since it could result in the electric shock. Furthermore, the liquid
splashes could damages the device and might cause smoke and overheat.
Always submit yourself into the safe driving rules and follow all traffic regulation. If you experience any
difficulties while operating the system or reading the monitor display, please stop your car and make any
necessary adjustment.
The Safety
Do not attempt to install or service your device on your own. Installation or serving by the people without
proper training and experience in the electronic equipment and the automotive accessories may be
dangerous and could lead into the risk of the electric shock or the other hazards.
If the receiver does not work properly, please disconnect the power plug for your safety and contact your
local dealer immediately for further technical support.
If any solid objects or liquids fall into the cabinet, please disconnect the unit and make it checked by the
qualified person before operating it any further.
impair with the performance of any vehicles operating system or the head unit, and
Table of Contents
Product Introduction ........................................................................................................... 4
I.
II.
III.
IV.
TV Mode ........................................................................................30
IV.1 TV Menu ......................................................................................................................................... 30
IV.1.1 CH List (Channel List) ..................................................................................................30
IV.1.2 Audio ............................................................................................................................... 31
IV.1.3 CH Info.(Channel Information) ....................................................................................31
IV.1.4 Auto Search ...................................................................................................................32
IV.1.5 Channel Manager .........................................................................................................32
IV.1.6 Display ............................................................................................................................ 33
IV.1.7 TV Setting.......................................................................................................................33
V.
VI.
VII.
VIII.
IX.
X.
Product Introduction
ASUKA HR-630 is designed for users to access terrestrial DVB-T2 TV broadcasting services
recently emerging in many countries. With its state-of-the-art TV signal reception performance and
AV codec processing techniques, HR-630 promises to deliver users an easy access of local HD
DVB-T2 TV programs as well as enhanced HD media player functions over existing multimedia
features.
Besides, HR-630 provides unique features and capability to make it more fun and convenient for
in-car information & entertainment experience. They are:
1. Smart phone connectivity: Its an easy & convenient to feed the smart phone contents into
the head-unit. Either iOS or Android mobile devices are supported.
2. Steering wheel control: For cars equipped with steering wheel control features, after a very
simple learning procedure, one can designate any 5 keys to perform the function of CH+, CH1,
ENTER, EXIT, and TV LIST respectfully. The use of steering wheel control keys for HR-630
operation control can significantly ease the operation complexity and make HR-630 extremely
suitable for in-car applications.
3. Providing both CVBS and RGB TV output: In addition to CVBS output, HR-630 also
provides optional RGB (progressive) TV output that is the expected video format by several
well-known head unit with the RGB TV output, HR-630 is capable of inter working with an even
wider range of head units in the market..
I. Unit Overview
I.1 Front Side
(1)
AV in
(2)
(3)
CCD in
DVR in
(4)
(5)
(6)
HDMI in
: HDMI signal input port for mobile phone connection.
Charging USB port : with DC +5V output for battery charging of mobile devices.
USB port
: for USB stick or external hard disk connection to perform
multimedia playback, TV recording, or software upgrade.
(7)
(8)
Operating LED
Power LED
13
11
9
10
12
14
(9)
Antenna in
(10)
(11)
(12)
(13)
HDMI out
Video out
Audio out
Monitor Port*1
(14)
Power/SWC/IR Port*2 : with 12V/24V, ACC & GND car power inputs, steering wheel
button signal inputs and IR control interface
No
Button name
POWER
SRC
3
4
HOME
MENU
CH
VOL
CH
FF
Fast Forward
[13]
TV LIST
TV Program List
[14]
10
ENTER
11
EXIT
12
VOL
13
OK
14
FR
Fast Rewind
15
REC
Function
Select the power-on or stand-by
Select
a
video
source
DTV/AV1/CCD/DVR
Go to the home screen
Enter the setup menu
[1]
[3]
from
[11]
[4]
[5]
[12]
[6]
[7]
[8]
[9]
or select
[15]
[10]
TV Mode
To enter the DTV mode.
Smart phone Link Mode
To enter the link mode and operate the smartpone
connectivity.
Movie Playback Mode
To enter the playback mode and watch the movie files.
Music Playback Mode
To enter the audio playback mode and listen to the music.
Radio Playback Mode
To enter radio playback mode and listen to Radio
broadcasting.
DVR Mode
To enter the driving recorder mode and watch the real
time video.
AV Mode
To select the AV output sourcing.
System Settings
To configure the device settings.
Note: Press the [HOME] key to go back to the home screen anytime.
Press the [SOURCE] key to switch the AV source anytime.
Configuration overview
The HR-630 provides three different kinds of video output ports: AV OUT, HDMI, and Monitor Port
Input devices
Driving Recorder
AV 1/AV2
USB devices
HR-630
CONNECTED Car TV Diversity
Receiver
Contents Sources
available at each
HR-630 output port
AV OUT
(CVBS signal)
TV
USB
Smartphone
Monitor Port
(RGB signal)
TV
USB
HDMI Port:
TV
USB
Smartphone
DVR
AV1/AV2
Steering In 1
Steering In 2
Ground (black wire). Connect this cable to the vehicles chassis ground.
- Reverse status (orange wire). Connect this cable to the reverse gear to see the
image of the rear view camera image on the front monitor.
- Keep the cable grounded if the reverse mode is not enabled.
+12 ~ 24 V DC input (yellow wire). Connect this cable to (+) pole of the battery
Steering In 2 (green wire). Plug in the cable to the SWC output wire 2.
ACC (red wire). Connect this cable to the ACC ignition of your vehicle.
Steering In 1 (Blue wire). Plug in the cable to the SWC output wire 1.
10
10
Monitor Port
UART_T
RGB_B
CsyncX
RGB_R
Ground
RGB_G
UART_RX
Ground
UART TX output
UART RX input
Csync output
Ground
Ground
Ground
Reserved
Audio input
IR data output
UART RX input
UART TX output
DVR Port
Mini USB
10 Reserved
11
(1)
(2)
(3)
(4)
(5)
Behind the Front Bumper. Note: Please make sure the bumper is not made of metal
Top of the Front Windscreen, but at least 5cm away from the metal body of the car
Top of the Rear Windscreen, but at least 5cm away from the metal body of the car
Bottom of the Rear Windscreen, at least 5cm away from the metal body of the car
Behind the Rear Bumper (note: make sure rear bumper is not made of metal)
*Noted: For position (2) ~ (4), because the windshields of many cars are usually equipped with film coating
(that contains metal), the actual signal reception may be degraded, depending on the amount of the metal
embedded within the film.
12
13
If you are like most people these days, youve made your smartphone the source for Youtube,
Google Map, and any other Internet information surfing.
To answer the increasing demand of Internet access within a car via smartphone, HR-630 provides
an efficient way to connect your smartphone to the head unit display on car monitor.
Configuration:
Connect your smart phone to the HDMI input port of HR-630. Different interconnection cable should
be used for iOS and Android devices, respectifully, as illustrated below:
iOS device :
device.
Android device:
14
If the connection is successfully activated, the mirroring image of smart phone will become also
available on car monitor as shown in the below:
15
Operation Overview
Steering Wheel
2 ~ 3 wires,
15V max
(GND, output_1,
& output_2)
AV SIGNAL
16
The steering wheel control signals available from most car models are usually consisted of 2 or 3
wires. Generally speaking, when one press a particular SWC button, a specific voltage will be
presented at one and/or 2 wires to inform the peripheral devices (ex. TV receiver) that a SWC
button has been asserted. The TV receiver can therefore interpret the voltage and perform the
corresponding action (CH+, CH-, ENTER, EXIT, TV LIST or nothing) in accordance with function
asserted.
The above-mentioned theories of operation are conceptually illustrated in the above wiring diagram.
-
The designated inputs of Power/IR port for SWC signals are Power GND (Black wire), Steering
In 1 (Blue wire), and Steering In 2 (Green wire).
2.
17
Learning
3. Learning Success
18
19
To enable the function of touch control operation, a specific installation way for different headunit is
required. For instance, the different interconnection cable is requested for each specific headunit to
connect with HR-630. The installation guide for each supported head units is summarized as below
for reference.
-
Configuration :
Video connection : Plug the SONY interconnection cable to the Monitor port on HR-630, and
insert the other side to Navigation port on SONY head unit.
Audio Connection : Plug audio L/R RCA cable to AV L/R Out on HR-630 and insert the other side
to AUX IN on SONY head unit.
Monitor port
20
21
JVC 2-DIN
22
Connect rear CCD camera to the CCD IN, Driving recorder into DVR IN, and/or any additional
AV source to the stanadrd AV inputs as shown below:
2.
23
Operating LED
Power LED
Step 2: Highlight the TV option to enter the TV mode. After that, the screen of
Setup Wizard will show up.
24
Step 5: Good Job! You can now sit back and enjoy your mobile TV.
NOTE: Press the [OK] button to change the aspect ratio of the current TV program.
25
III.2 TV Recording
1. While watching TV, press [REC] to start recording
TV programs. The timer menu will appear on the
lower left screen. This timer menu will disappear
automatically when no operation is performed
within 10 seconds.
2. Select favorite recording time on timer menu and
press [OK] to start the recording.
icon will
appear on the left upper screen. The information
of current recording time will be shown beside the
icon.
NOTE:
a. Please ensure that a USB Storage device is
b.
3. You can simply call the timer menu out with press [REC] again.
4. To stop recording, please select the STOP option
on timer menu.
Important notes:
i.
A recorded program will be stored in a default folder named PVR. The file
name will have .TSV file extention for recorded TV program.
ii.
The file will be named as:
"Channel Name(RecordedDate_RecordedTime)
iii.
Maximum file size of FAT/FAT32 is 4 GB, if the file exceeds this size, the system
will creat a new file to continue the recording.
iv.
1 GB storage can be used to save recorded program for approximately 45
ASUKA HR-630 User Manual
26
v.
vi.
minutes.
Storage system can support FAT/FAT32/NTFS formats.
Generally all USB 2.0 flash drive can be used as storage devices. However,
there are cases happening that the USB flash drive cant succesffuly store
recorded programs. So, before recording, its strongly suggested to first format
the USB storage device by PC or laptop
WARNING! Please do not edit the *.PLT & RECORD.TMP files on your disk.
Modifying/deleting this file will cause error on recorded file.
27
NOTE:
1. Press the [FR]
/ [FF]
28
NOTE:
1. Press the [FR]
/ [FF]
2. Press the [PLAY/PAUSE]
29
IV. TV Mode
IV.1 TV Menu
Enter TV mode first, and then press the
[MENU] button to make TV menu appear. By
navigating the different options, you can have the
access to the channel list, audio settings,
channel info, auto search, channel management,
display setting and the subtitle through setting
menu.
date.
Press the [VOL] button to see the
program schedule.
Scroll up/down the program schedule
to see the previous/next program on the selected date.
Press the [VOL] button to return back to the date list.
While in program schedule list, press the [OK] button to see more information of
30
IV.1.2 Audio
To select either master or secondary language as well as the audio channel of
current service
1. Highlight the Audio option on TV menu
screen.
NOTE: you can also press the [AUDIO]
button to enter the Audio while enjoying
TV.
2. Select the stereo/left/right audio channel
and scroll the available language. Press
the [OK] button to select the language.
3. Press the [EXIT]/[MENU] key to exit.
31
Skip a Channel
1. After entering the channel editing menu, select the SKIP visual-button on
screen.
2. Press the [OK] button to activate or deactivate it.
NOTE: this function temporarily removes the channel from the program list. The users
can restore the channels by deactivating the function.
Channel Movement
1. After entering the channel editing menu, select the MOVE visual-button on
screen.
2. Move the channel up or down in the list.
3. Press the [OK] button to save the new listing.
Channel Delete
1. After entering the channel editing menu, select the DELETE visual-button on
ASUKA HR-630 User Manual
32
screen.
2. Press the [OK] button to delete the channel.
NOTE: this function will permanently delete the channel from the current program list.
Users will only restore the previous channels back by performing the auto search again.
IV.1.6 Display
To set up and adjust the image with
preference.
1. Highlight the item you want to adjust.
2. Press the [OK] button to activate it.
IV.1.7 TV Setting
To configure the subtitle, teletext, and antenna power setting
III.1.7.1 Subtitle : to active or deative the subtitle function
1. Select the Subtitle option on TV menu
screen.
NOTE: you can also press the [REC]
button to enter the Subtitle while
enjoying TV.
2. Scroll the available language to activate
the subtitle.
3. Press the [EXIT]/[MENU] key to exit
III. 1.7.2 Teletext : to enter the teletext menu
1. Select the Teletext option on TV menu.
NOTE: you can also press the [TTX] button to enter the Teletext menu while
enjoying TV.
2. Press the [CH] button to view the next page or the [CH] to view the
previous teletext page.
3. Press the numerical key button to jump to the specific teletext page.
4. Press the [MENU]/[EXIT] to leave.
33
34
V. MOVIE Mode
In the Movie Menu, the users can adjust the playing mode, repeat mode, aspect
ratio, audio, and the subtitle.
1. Press the [MENU] to enter Menu.
2. Highlight the item you want to adjust.
3. Select one by pressing the [OK] button or exit
the setting by pressing the [EXIT]/[MENU]
button.
4. Press the [EXIT]/[MENU] button to exit the
Movie Menu.
Movie Menu
Playing Mode
Repeat Mode
Aspect Ratio
Audio
Subtitle
Options
Result
Off
Shuffle
RepeatOFF
The device will stop, right after playing one video file
RepeatOne
RepeatDir
Full Screen
None
Stereo
Left
Right
Languages
35
Repeat Mode
Options
Result
Off
Shuffle
RepeatOFF
The device will stop, right after playing one music file
RepeatOne
RepeatDir
36
VII.
Radio Mode
37
VIII.1 Country/Language
To set up the OSD language and regional settings
1. Highlight the item you want to adjust.
2. Select one option by pressing the the
[OK] button or exit the setting by
pressing the [EXIT]/[MENU] button.
3. After adjusting, press the [EXIT]/[MENU]
button to exit the Country/Language
menu.
VIII.2 Display
To set up and adjust the image with preference.
1. Highlight the setting that you want to
adjust.
2. Select one by pressing the [OK] button
or exit the setting by pressing the
[EXIT]/[MENU] button.
3. After adjusting, press the [EXIT]/[MENU]
button to exit the Display menu.
set
up
the
monitor
types
for
integration.
1. Press [OK] button or exit the setting by
pressing the [EXIT]/[MENU] button.
2. After adjusting, press the [EXIT]/[MENU]
button to exit the Monitor Port Setting
menu.
38
2.
Learning
3. Learning Success
39
40
41
42
No line-of-sight between
unit and controller
43
X. Specification
RF Input
Antenna
Frequency range
RF input impedance
Channel bandwidth
TV System
Transmission
standard
Video/Audio decoder
S/W Feature
English, German, French, Portuguese, Spanish, Italian, Dutch,
Finnish, Traditional Chinese, Thai, Indonesia
DVB-T/T2 TV, Auto Channel Search, MultiLanguage EPG,
Features
Steering Wheel Control (SWC)
TV/Radio Recording
Record TV programs on the USB device
Media formats supported
Media port
USB
MP3, WAV,
ASF(option), AAC(option), WMA(option),
Audio format
RM(option)
MPEG-I/II/IV, VOB, AVI, DivX, Xvid, MKV, TS, MOV,
Video format
RMVB(option), FLV(option), WMV(option), ASF(option)
Subtitle format
SRT, SUB, SSA, ASS, SMI, PSB, TXT, IDX
Recorded file format
*.tsv (TV recording)
Interface
1 Support the USB 2.0 host (for playback and for TV recording)
USB port
1 for smart phone charging
AV input port
1 A/V Input with RCA connector
DVR input port
1 Mini-USB input
CCD input port
1 CVBS input with RCA connector
DC Voltage input (Support +12V ~ 24V DC)
IR Signal input
Power/IR/SWC port
Steering
Wheel
Control
Signal
input
(Support
voltage:0.2~15V)
AV Output
2 CVBS Video out, 1 Audio (L/R) out
HDMI Output
1 HDMI output (Type A)
UART/RGB output
1 UART, 1RGB output
Monitor port
Dedicated port for advanced intergration with 2-DIN monitor
TV out
2 CVBS video out, 1 Audio (L/R) out, 1 HDMI out
Power
Input voltage
12-24 V DC
Power consumption
6.5 Watt, max
Dimension and Weight
Dimension
185*130*30 mm
Weight
630 g
OSD Language
44