Documente Academic
Documente Profesional
Documente Cultură
2/18/08
p. 25 -
p. 31 -
p. 40 -
p. 42 -
p. 50 -
p. 77 -
5 lines from bottom (not counting footnote): Eqn. 3.32 should be Eqn.
2.32
p. 127 -
p. 132 -
p. 138 -
p. 148 -
p. 152 -
p. 153 -
p. 164 -
p. 164 -
p. 169 -
p. 176 -
p. 191 -
p. 232 -
p. 273 -
p. 275 -
Self Test 4.6: Insert period after last sentence of answer: energy.)
Rev. 2/18/08
p. 278 -
p. 280 -
p. 287 -
3rd line from bottom: Insert left parenthesis before [=], i.e. ([=].
p. 362 -
p. 364 p. 366 -
p. 367 -
p. 399 -
p. 415 -
p. 420 -
p. 422 -
p. 455 -
p. 475 -
V g( P g DV / Dt )ds.
Location 1
p. 480 -
p. 490 -
Prob. 6.20: 2nd & 3rd sentence combined should read: The right and left
legs of the manometer have diameters d1 and d2, respectively, with z0 the
elevation at which the levels in the two legs become equal.
Note also that the interface between Fluid A & Fluid B on the sketch
should be moved down an arbitrary a distance below z0.
Rev. 2/18/08
p. 495 -
Problem 6.51: The dimension L should include only the cork and not
the nickel.
p. 505 -
p. 506 -
Problem 6.120: Delete (P1 = 150 kPa). Insert the following before
Find the suction: The pressure in the large-diameter main water line,
which supplies water to the primary tube of the device, is P0 = 150 kPa.
The velocity in the water main is negligible.
p. 509 -
p. 517 -
In 2nd equation & within Self Test 7.1, lower case m should be capital
M
p. 517 -
p. 532
p. 538 -
Sentence above Eqn. 7.22a should begin For Case II (not Case I),
whereas sentence below Eqn. 7.22a should begin For Case I (not Case
II).
p. 545 -
Self Test 7.6: Add masses to parenthetical material: (2 kg copper and 2.5
kg iron)
p. 553 -
p. 560 -
Answer to Self Test 7.9: Insert solidus before (1/P), i.e., /(1/P)
p. 568 -
p. 580 -
p. 590 -
p. 612 -
Add to Problem 8.4: What happens if you force Red to appear within
your result?
p. 613 -
p. 642 -
Fig. 9.13: Remove small rectangles in vertical axis legend and legend on
figure.
p. 643 -
Rev. 2/18/08
p. 649 -
p. 656 -
p. 657 -
p. 664 -
p. 668 -
3rd line below Cylinders & Other 2-D Shapes: Replace 5x105 with
> 104
p. 677 -
p. 670 -
p. 747 -
7th line following list of assumptions: vx(x only) should be vx(r only)
p. 789 -
p. 807 -
Prob. 10.25: Parts (a) & (b) should read: 0.253 cm3/s and 0.15 cm3/s,
respectively. Correct answers: (a) 1.38x10-6 m2/s (b) 2.38x10-6 m2/s (c)
9.02x10-6 m2/s.
p. 844 -
p. 851 -
p. 869 -
p. 888 -
p. 896 -
p. 896 -
p. 897 -
p. 931 -
p. 933 -
p. 935 -
Rev. 2/18/08
p. 940 -
p. 974 -
p. 1020 -
p. 1027 -
p. 1042 -
2nd column, 2nd line from bottom: Add hyphen at end of line.
p. 1047 -
p. 1049 -
p. 1050 -
Problem 12.59: Add per unit mass to the end of the last sentence.
p. 1050 -
Problem 12.60: Add per unit mass to the end of the last sentence.
p. 1051 -
p. 1054 -
Problem 12.91: Add Hint: Use saturation temperature for R-22 inlet and
outlet to evaluate Tlm.
p. 1058 -
Prob. 12.126: Reword: 0.15 MPa. Does any moisture condense? If so,
determine the moisture condensation rate (kg/min). If not, determine the
relative humidity.
p. 1059 -
Problem 12.135: Insert (dry basis) after 4-lbm mass of air and after 1lbm mass of air
p. 1059 -
p. 1059 -
Problem 12.143: Add word flow after word mass in Parts B & C.
p. 1062 -
p. 1063 -
p. 1107 -
Rev. 2/18/08
p. 1149 -
p. 1150 -
p. 1150 -
p. 1150 -
p. 1151 -
p. 1152 -