Documente Academic
Documente Profesional
Documente Cultură
This lead-free and RoHS-compliant multi-rate Small Form Factor Pluggable (SFP)
transceiver provides superior performance for Fibre Channel applications, and
is another in Picolights family of Accelar products customized for high speed,
PLRXPL-Vx-SGx-xx
short reach SAN,and intra-POP applications. The multi-rate feature enables its
use in a wider range of system applications. It is fully compliant with FC-PI
100-M5/M6-SN-I, 200-M5/M6-SN-I, and 400-M5/M6-SN-I specifications. The
rate select pin (pin 7) provides receiver bandwidth switching between 4.25G
/2.125G and 2.125/1.0625G line rates for optmized link performance enabling
hardware or software based rate-negotiation system architectures. Picolights
improved housing provides improved EMI performance for demanding 4GFC
applications. This transceiver features a highly reliable 850 nm oxide verticalcavity surface-emitting laser (VCSEL) coupled to a LC optical connector. Its
small size allows for high-density board designs that, in turn, enable greater
total aggregate bandwidth.
Key Benefits
HIGHLIGHTS
4GFC, 2GFC, and 1GFC triple rate performance enables flexible system
design, and configuration, while maximizing bandwidth
Triple-rate FC performance
March 2006
05001530 R3
Picolight, Inc.
PLRXPL-VE-SG4-62-x | p. of 22
850nm
PLRXPL-VE-SG4-62-x Features
Utilizes a highly reliable, high-speed, 850nm, oxide VCSEL
Lead-free and RoHS-compliant
Hot Pluggable
Digital Diagnostics, SFF-8472 rev 9.5 compliant
Compliant with Fibre Channel 400-M5/M6-SN-I, 200-M5/M6-SN-I,
and 100-M5/M6-SN-I
Selectable 4G/2G/1G receiver bandwidth with rate select pin 7 or
through digital diagnostics interface
Low nominal power consumption (400 mW)
-20C to 85C operating temperature range
Single +3.3 V power supply
10% extended operating voltage range
Bit error rate < 1 x 10-12
OC Transmit disable, loss of signal and transmitter
fault functions
CDRH and IEC 60825-1 Class 1 laser eye safe
FCC Class B compliant
ESD Class 2 per MIL-STD 883 Method 3015
UL-94 V-0 certified
Internal AC coupling on both transmit and receive data signals
ORDERING INFORMATION
Temp. Range:
Power Supply
Tolerance:
Rate
Select
Digital
Diagnostics
PLRXPL-VE-SG4-62
-20 to 85C
10%
PLRXPL-VE-SG4-62-N
-20 to 85C
10%
Part Number
Contact Information:
March 2006
05001530 R3
Picolight Incorporated
1480 Arthur Avenue
Louisville, CO 80027 USA
Picolight, Inc.
PLRXPL-VE-SG4-62-x | p. of 22
850nm
Transmitter
The transmitter converts 8B/10B encoded serial PECL or CML electrical data into serial optical data meeting the
requirements of 100-M5/M6-SN-I, 200-M5/M6-SN-I, and 400-M5/M6-SN-I Fibre Channel specifications. Transmit data
lines (TD+ & TD-) are internally AC coupled with 100 differential termination.
An open collector compatible Transmit Disable (Tx_Dis) is provided. This pin is internally terminated with a 10 k
resistor to VccT. A logic 1, or no connection on this pin will disable the laser from transmitting. A logic 0 on this pin
provides normal operation.
The transmitter has an internal PIN monitor diode that is used to ensure constant optical power output across supply
voltage and temperature variations.
An open collector compatible Transmit Fault (TFault) is provided. The Transmit Fault signal must be pulled high on the
host board for proper operation. A logic 1 output from this pin indicates that a transmitter fault has occurred, or the
part is not fully seated and the transmitter is disabled. A logic 0 on this pin indicates normal operation.
Receiver
The receiver converts 8B/10B encoded serial optical data into serial PECL/CML electrical data. Receive data lines (RD+
& RD-) are internally AC coupled with 100 differential source impedance, and must be terminated with a 100
differential load.
Rate select, pin 7, switches the receiver bandwith enabling superior performance at 4.25 Gbps, 2.125 Gbps, and 1.0625
Gbps line rates. With non rate-select part numbers or when rate-select is set high (4.25/2.125 Gbps mode) on rateselect part numbers, the receiver bandwidth is not compliant to the maximum receiver bandwidth specified under
100-M5/M6-SN-I.
200-M5/M6-SN-I
400-M5/M6-SN-I
No *
Yes
Yes
Low
Yes
Yes
No
March 2006
05001530 R3
Picolight, Inc.
PLRXPL-VE-SG4-62-x | p. of 22
850nm
An open collector compatible Loss of Signal is provided. The LOS must be pulled high on the host board for proper
operation. A logic 0 indicates that light has been detected at the input to the receiver (see Section 2.5 Optical
characteristics, Loss of Signal Assert/Deassert Time on page10). A logic 1 output indicates that insufficient light has
been detected for proper operation.
Power supply filtering is recommended for both the transmitter and receiver. Filtering should be placed on the host
assembly as close to the Vcc pins as possible for optimal performance.
Recommended Application Schematics are shown in Figure2 on page5.
Figure 1
Block diagram
10 k
16 Transmitter
Power Supply
3 Transmitter
Disable In
VCC_TX TX_DIS
TOSA
18 Transmitter
Positive Data
TD+
Laser Driver
TX_GND
TX_FAULT
100
19 Transmitter
Negative Data
TD -
2 Transmitter
Fault Out
1, 17, 20 Transmitter
Signal Ground
5 MOD_DEF(1)
Serial ID Clock
4 MOD_DEF(2)
Serial ID Data
SCL
Management Processor
EEPROM
SDA
6 MOD_DEF(0)
15 Receiver
Power Supply
VCC_RX
ROSA
RX_GND
VCC_RX
Receiver
RD -
50
RD +
RX_GND Rate_Select
LOS
50
12 Receiver
Negative Data Out
13 Receiver
Positive Data Out
7 Rate Select
30 k
9, 10, 11, 14 Receiver
Signal Ground
March 2006
05001530 R3
Picolight, Inc.
PLRXPL-VE-SG4-62-x | p. of 22
850nm
Figure 2
Z* = 100
10 k
1 VeeT
VeeT 20
R2* 50
Open Collector Driver
(Tx Disable)
10 k
TD+ 18
4 MOD_DEF(2)
L1
1 H
C1
10F
VccR 15
C5
10 F
7 Rate Select
Receiver
(Mod_Def(0))
C2
0.1F
L2
1 H
C4
0.1 F
10 k
6 MOD_DEF(0)
VccT 16
Vcc
VeeT 17
C3
0.1F
5 MOD_DEF(1)
10 k
Open Collector
Bidirectional
(Mod_Def(1))
3 Tx Disable
Vcc
TD- 19
Open Collector
Bidirectional
(Mod_Def(2))
Vcc
2 Tx Fault
VccR 14
R3*
50
8 LOS
RD+ 13
Z* = 100
Rate Select
9 VeeR
RD- 12
10 VeeR
VeeR 11
Vcc
10 k
R4*
50
Receiver (LOS)
Notes
Power supply filtering components should be placed as close to the Vcc pins of the host connector as
possible for optimal performance.
PECL driver and receiver will require biasing networks. Please consult application notes from suppliers of
these components. CML I/O on the PHY are supported.
MOD_DEF(2) and MOD_DEF(1) should be bi-directional open collector connections in order to implement
serial ID (MOD_DEF[0,1,1]) PLRXPL-VE-S64-62-x transceiver.
March 2006
05001530 R3
R1 and R2 may be included in the output of the PHY. Check application notes of the IC in use.
Transmission lines should be 100 differential traces. It is recommended that the termination resistor for the
PECL Receiver (R3 + R4) be placed beyond the input pins of the PECL Receiver. Series Source Termination
Resistors on the PECL Driver (R1+R2) should be placed as close to the driver output pins as possible
Picolight, Inc.
PLRXPL-VE-SG4-62-x | p. of 22
850nm
March 2006
05001530 R3
Picolight, Inc.
PLRXPL-VE-SG4-62-x | p. of 22
850nm
Symbol
Name
Description
Receiver
LOS
9, 10, 11,
14
VeeR
12
RD-
13
RD+
15
VccR
This pin should be connected to a filtered +3.3V power supply on the host board. See
Application schematics on page5 for filtering suggestions.
Rate
Transmitter
3
TX Disable
Transmitter Disable In
(LVTTL)
1, 17, 20
VeeT
TX Fault
16
VccT
This pin should be connected to a filtered +3.3V power supply on the host board. See
Application schematics on page5 for filtering suggestions.
18
TD+
19
TD-
Transmitter DATA inputs are internally AC coupled and terminated with a differential
100 resistor.
Transmitter DATA inputs are internally AC coupled and terminated with a differential
100 resistor.
Module Definition
6, 5, 4
March 2006
05001530 R3
MOD_DEF
(0:2)
Module Definition
Identifiers
Picolight, Inc.
PLRXPL-VE-SG4-62-x | p. of 22
850nm
Symbol
Ratings
Unit
Storage Temperature
Tst
-40 to +95
Tc
-20 to +85
Vcc
0 to +4.0
VP-P
VD
2.5
Relative Humidity
RH
5 to 95
Symbol
Min
Typical
Max
Unit
Vcc
2.97
3.3
3.63
1.0
2.125
4.25
Gbps
40
70
mA
800
2200
mVp-p
80
ps
Data Rate
Notes
Transmitter
Supply Current
Data Input Voltage Swing
ICCT
VTDp-p
250
40
40
175
ps
40
350
ps
20
ps
DJ
0.12
UI
DJ
0.14
UI
DJ
0.14
UI
TJ
0.25
UI
TJ
0.26
UI
27-1 pattern, T ,
BER < 1x10-15, @ 2.125Gbps 1, 5
TJ
0.26
UI
27-1 pattern, T ,
BER < 1x10-15, @ 4.25 Gbps 1, 5
March 2006
05001530 R3
Picolight, Inc.
PLRXPL-VE-SG4-62-x | p. of 22
850nm
Symbol
Min
VIH
VIL
Typical
Max
Unit
Vcc -1.0
Vcc
0.8
10
TTD
ms
VOH
Vcc -0.5
Vcc
VOL
0.5
TFault
100
Initialization Time
TTEN
TReset
10
TINI
Notes
Laser output disabled after TTD if input level
is VIH; Laser output enabled after TTEN if
input level is VIL
300
ms
85
120
mA
720
1300
mVp-p
80
120
ps
Receiver
Supply Current
ICCR
600
40
ps
DJ
0.36
UI
DJ
0.39
UI
DJ
0.39
UI
Total Jitter
TJ
0.61
UI
27-1 pattern, R ,
Total Jitter
TJ
0.64
UI
Total Jitter
TJ
0.64
UI
VOH
Vcc -0.5
Vcc
VOL
March 2006
05001530 R3
0.5
TLOSA
100
TLOSD
100
Picolight, Inc.
PLRXPL-VE-SG4-62-x | p. of 22
850nm
Symbol
Min.
Typical
Max
Unit
850
860
nm
0.5
0.85
nm
-2.5
dBm
90
ps
1125
Notes
Transmitter
Wavelength
Pm
PAVG
trise/fall
OMA
840
-9
250
20% - 80%
Deterministic Jitter
DJ
0.21
UI
Deterministic Jitter
DJ
0.26
UI
Deterministic Jitter
DJ
0.26
UI
Total Jitter
TJ
0.43
UI
Total Jitter
TJ
0.44
UI
Total Jitter
TJ
0.44
UI
-118
dB/Hz
12 dB reflection
850
860
nm
RIN
-125
1, 5
Receiver
770
Pm
Sensitivity (OMA)
S1
18
31
Wp-p
S2
25
49
Wp-p
2 Gbps operation
61
Wp-p
4 Gbps operation
WP-P
1G operation
WP-P
2G operation
WP-P
4G operation
dBm
Wavelength
dBm
S4
SS2
Ss4
Loss of Signal Assert/Deassert
Level
Low Frequency Cutoff
March 2006
05001530 R3
ISI = 0.96
55
dB
ISI = 2.18
dB
67
ISI = 1.26
dB
96
ISI = 2.03
dB
109
ISI = 1.67
dB
138
ISI =
2.14dB
148
LOSD
LOSA
FC
-17
-30
dBm
0.2
0.3
MHz
Picolight, Inc.
PLRXPL-VE-SG4-62-x | p. 10 of 22
850nm
Fiber Type
Distance Range
(m)
Notes
1.0625 GBd
Fibre Channel
100-M5-SN-I
100-M6-SN-I
62.5/125 m MMF
200
2 to 300
50/125 m MMF
500
2 to 500
50/125 m MMF
900
2 to 630
50/125 m MMF
1500
2 to 755
50/125 m MMF
2000
2 to 860
62.5/125 m MMF
200
2 to 150
50/125 m MMF
500
2 to 300
50/125 m MMF
900
2 to 350
50/125 m MMF
1500
2 to 430
50/125 m MMF
2000
2 to 500
62.5/125 m MMF
200
2 to 70
50/125 m MMF
500
2 to 150
50/125 m MMF
900
2 to 175
50/125 m MMF
1500
2 to 215
50/125 m MMF
2000
2 to 270
2.125 GBd
Fibre Channel 200-M5-SN-I, 200M6-SN-I
4.25 GBd
Fibre Channel 200-M5-SN-I, 200M6-SN-I
Specification notes
1. UI (Unit Interval): one UI is equal to one bit time. For example, 2.125 Gbits/s corresponds to a UI of
470.588ps.
2. For LOSA and LOSD definitions see Loss of Signal Assert/Deassert Level in Section 2.5 Optical characteristic
s on page10.
3. When operating the transceiver at 1.0 - 1.3 Gbaud only, a slower input rise and fall time is acceptable. If it is
planned to operate the module in the 1.0 - 4.25 Gbaud range, faster input rise and fall times are required.
4. Measured with stressed eye pattern as per FC-PI (Fibre Channel) using the worst case specifications.
5. All jitter measurements performed with worst case input jitter according to FC-PI.
6. Distances, shown in the Link Length table, are the distances specified in the Fibre Channel standards. Link
Length distances are calculated for worst case fiber and transceiver characteristics based on the optical and
electrical specifications shown in this document using techniques utilized in IEEE 802.3 (Gigabit Ethernet). In
the nominal case, longer distances are achievable.
March 2006
05001530 R3
Picolight, Inc.
PLRXPL-VE-SG4-62-x | p. 11 of 22
850nm
Feature
Test Method
Performance
IEC 60825
Accession # 9922782
Electromagnetic Interference
(EMI)
Immunity
March 2006
05001530 R3
Lead-free and
RoHS-Compliant
Directive 2002/95/EC
Component
UL 1950
UL File #E209897
Picolight, Inc.
PLRXPL-VE-SG4-62-x | p. 12 of 22
850nm
NOTES:
34.50
2X 30
A
20
3X 10
CROSS-HATCHED AREA
DENOTES COMPONENT
AND TRACE KEEPOUT
(EXCEPT CHASSIS GROUND)
2X 7.20
0.850.05 2
(MARKED "S")
0.1 A B
2X 2.50
2X 2.50
11.9 1
14.25
TYP
C
D
3.68
A
16.25
3X 7.10
11.08
1.70
8.48
5.68
8.58
11.93
9.60
4.80
A
A
1.70
2 TYP
2 10X
0.1
1.050.05
L
A C
9X 0.950.05 3
(MARKED "G")
0.1 L A C
26.80
10
3 PLACES
41.30
42.30
2X 0.90
G
10.93
10.53
9.60
9X 0.8
11.93
9X 0.8
2X 1.550.05
0.1 L C D
20X 0.500.03
0.06 C D
20.05 TYP
0.06 L C D
March 2006
05001530 R3
Picolight, Inc.
PLRXPL-VE-SG4-62-x | p. 13 of 22
850nm
Picolight, Inc.
PLRXPL-VE-SG4-62-x | p. 14 of 22
850nm
6X .600.004
4X .640.004
.135
6X .41.00
.074
.042
.138
March 2006
05001530 R3
Picolight, Inc.
PLRXPL-VE-SG4-62-x | p. 15 of 22
850nm
The enhanced digital diagnostics feature monitors five key transceiver parameters which are Internally Calibrated and
should be read as absolute values and interpreted as follows;
Transceiver Temperature in degrees Celsius: Internally measured. Represented as a 16 bit signed twos complement
value in increments of 1/256 degrees Celsius from -40 to +125C with LSB equal to 1/256 degrees C. Accuracy is 3
degrees Celsius over the specified operating temperature and voltage range.
Vcc/Supply Voltage in Volts: Internally measured. Represented as a 16 bit unsigned integer with the voltage defined
as the full 16 bit value(0-65535) with LSB equal to 100mV with a measurement range of 0 to +6.55V. Accuracy is 3%
of nominal value over the specified operating temperature and voltage ranges.
TX Bias Current in mA: Represented as a 16 bit unsigned integer with current defined as the full 16 bit value(0-65535)
with LSB equal to 2mA with a measurement range of 0 - 131mA. Accuracy is 10% of nominal value over the specified
operating temperature and voltage ranges.
TX Output Power in mW: Represented as a 16 bit unsigned integer with the power defined as the full 16 bit value (065535) with LSB equal to 0.1mW. Accuracy is 2dB over the specified temperature and voltage ranges over the range
of 100mW to 800mW( -10dBm to -1dBm). Data is not valid when transmitter is disabled.
RX Received Optical Power in mW: Represented as average power as a 16 bit unsigned integer with the power defined
as the full 16 bit value(0-65535) with LSB equal to 0.1mW. Accuracy is 3dB over the specified temperature and voltage
ranges over the power range of 30mW to 1000mW (-15dBm to 0dBm).
Picolight, Inc.
PLRXPL-VE-SG4-62-x | p. 16 of 22
850nm
The information stored in the EEPROM including organization is defined in the Small Form-Factor document SFF-8472
draft rev 9.5, dated June 1, 2004.
Address( 1010000X)(A0h)
Serial ID Information;
Defined by SFP MSA
95
Picolight Specific
Information
127
127
247
March 2006
05001530 R3
55
255
Address( 1010001X)(A2h)
255
Picolight, Inc.
PLRXPL-VE-SG4-62-x | p. 17 of 22
850nm
Value
Comments
03
SFF Transceiver
04
07
LC Connector
3-10
0000000020400C15
11
01
12
2A
13
00
Reserved
14
00
15
00
16
0F
17
07
18
00
19
00
Reserved
20-35
PICOLIGHT
36
00
Reserved
37-39
000485
40-55
56-59
60-61
62
Reserved
63
64
00
Reserved
65
3A
Rate Select, Tx_Disable, Tx Fault, Loss of Signal implemented; -62 part numbers
65
1A
66
00
67
00
68-83
84-91
FO
Alarms & Warnings, TX_Fault and Rx_LOS monitoring implemented, TX_Disable Control &
Monitoring. -62-N part number
F8
Alarms & Warnings, TX_Fault and Rx_LOS monitoring implemented, TX_Disable Control &
Monitoring, Rate Select. -62 part number
94
01
95
64_94
92
93
March 2006
05001530 R3
96-127
128-255
Reserved
Picolight, Inc.
PLRXPL-VE-SG4-62-x | p. 18 of 22
850nm
Value
Comments
00-01
02-03
04-05
06-07
08-09
10-11
12-13
14-15
16-17
18-19
20-21
22-23
24-25
26-27
28-29
30-31
32-33
34-35
36-37
38-39
40-55
Reserved
56-59
RP4
60-63
RP3
64-67
RP2
68-71
RP1
72-75
RP0
76-77
Islope
78-79
Ioffset
80-81
TPslope
82-83
TPoffset
84-85
Tslope
86-87
Toffset
88-89
Vslope
90-91
Voffset
92-94
Reserved
Reserved
95
Checksum
96
Temperature MSB
97
Temperature LSB
98
March 2006
05001530 R3
Vcc MSB
99
Vcc LSB
100
TX Bias MSB
850nm
Value
101
TX Bias LSB
102
TX Power MSB
103
TX Power LSB
104
RX Power MSB
105
RX Power LSB
106
107
108
Reserved MSB
Comments
Measured TX output power AD values
Reserved LSB
Reserved MSB
109
Reserved LSB
110-7
Tx Disable State
110-6
110-5
Reserved
110-4
110-2
Tx Fault State
Digital State
110-1
LOS State
Digital State
110-0
111
Reserved
Reserved
112-119
120-127
Vendor specific
Vendor specific
128-247
User/Customer EEPROM
248-255
Vendor specific
Vendor specific
110-3
March 2006
05001530 R3
Picolight, Inc.
PLRXPL-VE-SG4-62-x | p. 20 of 22
850nm
Do not use halogenated hydrocarbons (e.g. trichloroethane, ketones such as acetone, chloroform, ethyl acetate, MEK,
methylene chloride, methylene dichloride, phenol, N-methylpyrolldone).
Flammability
The PLRXPL-VE-SG4-62-x housing is made of cast zinc and sheet metal.
March 2006
05001530 R3
Picolight, Inc.
PLRXPL-VE-SG4-62-x | p. 21 of 22
850nm
Caution!
Tampering with this laser based product or operating this product outside the limits of this specification may be
considered an act of manufacturing, and will require, under law, recertification of the modified product with the U.S.
Food and Drug Administration (21 CFR 1040).
Caution!
The use of optical instruments with this product will increase eye hazard. At the normal operating current, optical output
power with an unaided eye can be as much as 30 uW at a wavelength of 850 nm. Approximately ten times this power
level could be collected with an eye loupe.
Information in this document is provided in connection with Picolight Incorporated (Picolight) products.These materials are provided by Picolight as a service to its customers and
may be used for informational purposes only. Picolight assumes no responsibility for errors or omissions in these materials. Picolight may make changes to pricing, specifications,
and product descriptions at any time, without notice. Picolight makes no commitment to update this information and shall have no responsibility whatsoever for conflicts or
incompatibilities arising from future changes to its specification and product descriptions. No license, expressed or implied, to any intellectual property rights is granted by this
document. Except as provided in Picolights Terms and Conditions of Sale for such products, Picolight assumes no liability whatsoever.
THESE MATERIALS ARE PROVIDED AS IS WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, RELATING TO SALE AND/OR USE OF PICOLIGHT PRODUCTS
INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, CONSEQUENTIAL OR INCIDENTAL DAMAGES, MERCHANTABILITY, OR
INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. PICOLIGHT FURTHER DOES NOT WARRANT THE ACCURACY OR COMPLETENESS OF
THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN THESE MATERIALS. PICOLIGHT SHALL NOT BE LIABLE FOR ANY SPECIAL, INDIRECT INCIDENTAL,
OR CONSEQUENTAL DAMAGES, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR LOST PROFITS, WHICH MAY RESULT FROM THE USE OF THESE MATERIALS.
Picolight Incorporated
1480 Arthur Avenue
Louisville, CO 80027 USA
2005 Picolight, Inc. All rights reserved. Picolight Incorporated and the Picolight logo are trademarks or registered trademarks of Picolight Incorporated in the United
States and/or select foreign countries. All other company, brand, and product names are marks of their respective holders.
March 2006
05001530 R3
Picolight, Inc.
PLRXPL-VE-SG4-62-x | p. 22 of 22