Documente Academic
Documente Profesional
Documente Cultură
UPDATING
GUIDE
RADIO-INTERCOM
3 WIRE SYSTEMS
4 WIRE SYSTEMS
6/8 WIRE SYSTEMS
3-Wire
Radio-Intercom
Updating Guide
Older 3-wire systems may be converted to an IM-3303 Series Radio-Intercom System.
This booklet outlines the updating procedure; indicating the components that may be retained
from the existing system and the units that should be replaced.
NOTE: Due to component size differences, some wall patching may be required when
installing new systems.
IMPORTANT: The Radio-Intercom Systems are designed to be used only with NuTone specified wire.
No other wire should be used. The use of wire other than NuTone wire may result in faulty installation and
improper operation. Refer to the installation instructions packaged with each model for detailed installation
information.
SET
MASTER
VOLUME
AM
PM
RADIO
12: 0 0
ON OFF
TIME
SCAN
KHz
MHz
PROGRA
M OFF
AM
MEMORY
FM
MEMORY
MEMORY
AUX
MEMORY
TIMER
MEMORY
CD/TAP
INSIDE/PAT
IO
DOOR TAL
MEMORY
END CAL
IM-3303 Series
Master Station:
IM-3303WH Bright White Finish
IM-3303L Biscuit Finish
System may include a maximum of thirteen (13) remote
speakers and three (3) door speakers.
Wiring Requirements:
Three-wire system.
Maximum of 300 feet per remote station.
Maximum of 2000 feet total per system.
Rough-In Frame for Master Station:
Model IR-104 Rough-In Frame
(includes (2) Model 301T transformers and
omni-directional AM/FM antenna.)
Power Source:
(2) Model 301T transformers (16 volt, 30VA.)
Mounts in transformer boxes located in bottom of
rough-in frame.
OPTIONAL 3-WIRE
ACCESSORIES
UPDATING
RADIO-INTERCOM SYSTEMS (continued)
Master Station Model Number: IM-3003
Wiring Requirements:
Use existing 3-conductor wiring from the master station to remotes.
Use existing AM/FM antenna.
Rough-In Frame for Master Station:
For IM-3303, remove and replace with IR-104 or leave frame in place, but replace 105T transformer with
two (2) 301T transformers, remote mounted. Observe local electrical codes.
Power Source:
Install (2) 301T transformers (supplied with IR-104).
5" Speakers with Controls:
Use existing speakers.
8" Speakers with Controls:
Use existing speakers.
Remote Controls:
Use existing remote controls.
Speakers without Controls:
Use existing speakers, wiring and rough-in frames.
Door Speakers:
Use existing speakers, wiring and rough-in frames.
ROUGH-INS
IR-55
Housing for Recessed Patio
Speakers.
Cutout: 5 38" wide x 7 316"
high.
5"
IR-6
Housing for built-in Door
Speakers.
3 / "
Cutout: 31116" wide x 5" high.
7 3/16"
1 3/4 "
11 16
53/8"
2 3/4"
10 3/4"
111/16 "
14
12 / "
11 16
/ "
1 16
2 3/4"
5 /8"
IR-70
Housing
for IS-76
Round
Speaker.
11/2"
IR-90
Housing for CP-95
Cassette Deck.
Cutout: 1412" wide x 214" high.
14 1/2"
2 1/4"
IR-104
Housing for Master
Stations. includes
7"
transformer and omnidirectional FM/AM
14 / "
antenna.
Cutout: 1412" wide x 7" high.
33/8"
11/4"
IR-50
Housing for 5"
Inside Speakers.
3
Cutout: 5 8" wide x 7 316" high.
7 3/16"
6 1/8"
12 3/8"
2 5/8"
IR-9
Housing for IS-79 Wall
10 / "
Cutout.
1
Dimensions: 10 16" wide x 7316" high.
3 1/4" IR-91
101/4"
IR-80
Housing for 8"
Inside Speakers.
Cutout: 858" x 858" high.
12
UPDATE FRAMES
IA-119WH Bright White
For use with IM-3303WH.
IA-55WH/L
Bright White
To update 5"
horizontal
speakers from
older systems
to IS-335 Series.
IA-83WH/L
Primer White
To update larger speakers from
older systems to IS-338 Series.
OPTIONAL ACCESSORIES
Chime Modules
Cassette Deck
Model CP-95
Model IA-28: Plays eight (8) notes for front door, two (2) notes
for rear door and one (1) note for a third door.
Model IA-29: Deluxe Chime Module plays your choice of ten
(10) melodies for front door, plus two (2) notes for rear door,
one (1) note for a third door. Melodies include Westminster
Chimes (8 notes and 4 notes), Anniversary Waltz, Beethoven's
Fifth, Dixie, Greensleeves, Happy Birthday, Jingle Bells, Joy
To The World, Mazel Tov, Oh Tannenbaum, and Star Spangled
Banner.
A NuTone Electronic Chime may also be used with the RadioIntercom System.
6/8-Wire
Radio-Intercom
Updating Guide
Older 6/8-wire systems may be converted to an IM-4406 or IM-5000 Series RadioIntercom System.
This booklet outlines the updating procedure; indicating the components that may be
retained from the existing system and the units that should be replaced.
IMPORTANT: The Radio-Intercom Systems are designed to be used only with NuTone specified wire.
No other wire should be used. The use of wire other than NuTone wire may result in faulty installation
and improper operation. Refer to the installation instructions packaged with each model for detailed
installation information.
Master Station:
IM-4406L Biscuit Finish
IM-4406BL Black Finish
IM-4406WH Bright White Finish
System may include up to nine (9) remote stations and
three (3) door speakers.
NOTE: NuTone Model IA-440 Expansion Kit (sold
separately) will allow up to 15 remote stations and
three (3) door speakers to be used with the system.
Wiring Requirements:
An individual 6-wire cable (NuTone IW-6) must be
Home Run from each remote station to the master
station's terminal board.
Maximum speaker run: 750 feet.
Maximum total of IW-6 per system: 4000 feet.
Rough-In Frame for Master Station:
Model IR-105 Rough-In Frame
(includes (2) Model 801T transformers and
omni-directional AM/FM antenna.)
Power Source:
(2) Model 801T transformers (18 volts, 72VA.)
Mounts in transformer box located in bottom of
rough-in frame.
IM-5000 Series
IM-4406 Series
Master Station:
IM-5000 Bright White Finish
System will accommodate up to 20 remote stations
plus up to three (3) door speakers.
Wiring Requirements:
An individual 6-wire cable (NuTone IW-6) must be
connected to each remote station.
Maximum speaker run: 750 feet.
Maximum total of IW-6 per system: 4000 feet.
NOTE: For best results it is suggested that the IM-5000
Intercom System is installed in such a way that a
combination of Home Run wiring and Looped wiring
(zone wiring) are both used.
IM-5000 is surface mounted. No Rough-In Required.
Power Source: (Purchase Separately)
One (1) Model 401T transformer (24 volts, 40VA.)
Power Source:
IM-4406: Use (2) 801T transformer(s) included with
IR-105 Rough-In Frame. IM-5000: Use (1) 401T
transformer.
Speakers with Controls:
Remove and replace existing speakers and
rough-ins with IR-50 or IR-80 Rough-In Frames and
5" or 8" Speakers.
NOTE: Wall patching may be required..
Door Speakers:
Replace existing speakers. Use existing wiring
and rough-in frames.
*The IM-5000 can be mounted remotely (i.e., pantry, closet, etc.) and existing master replaced with 8" speaker with
controls (wall patching required). Wiring from existing master must be extended to IM-5000 location.
11
*The IM-5000 can be mounted remotely (i.e., pantry, closet, etc.) and existing master replaced with 8" speaker with
controls (wall patching required). Wiring from existing master must be extended to IM-5000 location.
12
PRIVATE
O FF
ON
NuTone
I N S I D E / PAT I O
TA L K
DOOR
TA L K
END
CALL
AM/FM/CD
CONTROL
VOLUME
NuTone
ISA-78L
(Adobe White)
ISA-78WH
(Bright White)
Use with Inside
Remote Control.
IS-445D
(Sable Brown)
IS-445L
(Biscuit)
IS-445WH
(Bright White)
IS-445BL
(Black)
P R I VAT E
OFF ON
I N S I D E / PAT I O
TA L K
DOOR
TA L K
END
CALL
AM/FM/CD
CONTROL
VOLUME
VOLUME
P R I VAT E
OFF
ON
I N S I D E / PAT I O
TA L K
DOOR
TA L K
END
CALL
AM/ F M / C D
CONTROL
NuTone
NuTone
IS-448D
(Sable Brown)
IS-448L
(Biscuit)
IS-448WH
(Bright White)
IS-448BL
(Black)
IC-441WHW
(Bright White)
Surface-mounted.
For use with
ISA-77, IS-79.
P R I VAT E
OFF ON
I N S I D E / PAT I O
TA L K
END
CALL
DOOR
TA L K
AM/FM/CD
CONTROL
VOLUME
IC-441WH
(Bright White)
For use with IS-76,
ISA-78L & WH, IS-82 8" Outdoor Speaker
IS-449WH
(Bright White)
Surface-mounted.
one
NuT
ISA-77
Surface-mounted.
Use with Outdoor
Remote Control.
IS-82
Use with Inside
Remote Control.
P R I VAT E
OFF
ON
I N S I D E / PAT I O
TA L K
DOOR
TA L K
END
CALL
AM / F M / C D
CONTROL
VOLUME
Table-top or Surface-mounting
Frame for 5" Inside Speaker
IA-6
Wall Receptacle for
IA-60 Series.
IA-6C
8' Cable for IA-6.
NuTone
IA-60D
(Walnut)
IA-60L
(Biscuit)
IA-60WH
(Bright White)
NuTone
IS-419WH
(Bright White)
IS-419AB
(Antique Brass)
IS-419PB
(Polished Brass)
Recessed.
ISA-63
Molded,
Surface-mounted.
NuTone
ISB-64
Molded,
surface-mounted.
NuTone
IS-67D
(Woodgrain/Brass)
IS-67WH
(White)
Molded, recessed.
IS-76 (White)
Use with Inside
Remote Control.
8" Inside Speaker - Round
NuTone
IS-69AB
(Antique Brass)
IS-69PB
(Polished Brass)
IS-69WH
(White)
Classic Cast Metal
Recessed.
IA-70
(Black)
For recessed door speakers.
NuTone
ISA-78L
(Adobe White)
ISA-78WH
(Bright White)
Use with Inside
Remote Control.
IS-515L
(Biscuit)
IS-515WH
(Bright White)
IS-79
Recessed.
Use with Outdoor
Remote Control.
8" Outdoor Speaker
IS-518WH
(Bright White)
NuTone
IC-502L
ISA-77
(Biscuit)
Surface-mounted.
IC-502WH
Use with Outdoor
(Bright White)
Remote Control.
For use with IS-76,
*
ISA-78L & WH,
NuTone
IS-82
8" Outdoor Speaker
Inside Remote Control
1
one
NuT
IA-60L
(Biscuit)
IA-60WH
(Bright White)
NuTone
IS-519
(Biscuit)
Recessed.
ISA-63
Molded,
surface-mounted.
NuTone
IA-6
Wall Receptacle for IA-60
Series.
IA-6C
8' Cable for IA-6.
IS-82
Use with Inside
Remote Control.
IS-67D
(Woodgrain/Brass)
IS-67WH
(White)
Molded, recessed
NuTone
ISB-64
Molded,
surface-mounted.
NuTone
Door
Speaker
IS-70AB
(Antique Brass)
IS-69AB
IS-70PB
(Antique Brass)
(Polished Brass)
IS-69PB
IS-70WH
(Polished Brass)
(Bright White)
IS-69WH
Classic Cast Metal
(White)
Recessed.
Classic Cast Metal
Door
Speaker
- no pushbutton
Recessed.
Door Speaker with Lighted Pushbutton
NuTone
NuTone
IS-76 (White)
Use with Inside
Remote Control.
8" Inside Speaker - Round
NuTone
IC-502LW
(Biscuit)
For use with
ISA-77, IS-79.
IA-70
(Black)
For recessed door speakers.
Surface-Mounting Frame
ROUGH-INS
5"
IR-6
Housing for built-in Door
3 / "
Speakers.
Cutout: 31116" wide x 5" high.
8 5/8"
11/2"
1 3/4 "
11 16
IR-91
Housing for IC-502, IC-441
6 1/8"
Remote Control.
Cutout: 6 18" wide x 3 14" high.
3 1/4"
IR-80
Housing for 8"
Inside Speakers.
Cutout: 858" wide x 1014" high.
101/4"
2 5/8"
IR-9
Housing for IS-79 Wall
10 / "
Cutout.
Cutout: 10116" wide x 11116" high.
111/16 "
IR-90
Housing for CP-95
Cassette Deck.
Cutout: 1412" wide x 214" high.
14 1/2"
53/8"
11/4"
16
IR-50
Housing for 5"
Inside Speakers.
Cutout: 538" wide x 7 316" high.
7 3/16"
2 1/4"
12 3/8"
3 3/8 "
IR-105
7 / "
Housing for Master
9" Stations. Includes (2)
IR-55
801T transformers and
5/"
14 / "
Housing for IS-419 & IS-519
omni-directional
Recessed Patio Speakers.
FM/AM antenna.
3
1
Cutout:
5
8
"
wide
x 7 316" high.
Cutout: 14 2" wide x 9" high.
2 3/4"
10 3/4"
3 16
3 8
12 1/4"
11 16
/ "
IR-70
Housing
for IS-76
Round
Speaker.
2 3/4"
OPTIONAL
OPTIONALACCESSORIES
ACCESSORIES
Intercom Accessories
Cassette Deck
Model CP-95
Model IA-28 Chime Module: Plays eight (8) notes for front door,
two (2) notes for rear door and one (1) note for a third door.
Model IA-29 Deluxe Chime Module: Plays your choice of ten
(10) melodies for front door, plus two (2) notes for rear door,
one (1) note for a third door. Melodies include Westminster
Chimes (8 notes and 4 notes), Anniversary Waltz, Beethoven's
Fifth, Dixie, Greensleeves, Happy Birthday, Jingle Bells, Joy To
The World, Mazel Tov, Oh Tannenbaum, and Star Spangled
Banner.
A NuTone Electronic Chime may also be used with the IM-4406
Radio-Intercom and IM-5000 Intercom.
15
4-Wire
Radio-Intercom
Updating Guide
NuTone model number IM-3204 may be used to update other 4-wire systems. Rough-in
frames for the speakers and master units may differ in size depending on the manufacturer.
Specific product information is available in NuTones full line catalog.
IM-3204 Series