Documente Academic
Documente Profesional
Documente Cultură
A
1070 (42 1/ 8)
1170 (46 1/16)
1140 (44 57/64)
1329 (52 21/64)
B
596 (23 15/32)
656 (25 53/64)
757 (29 51/64)
870 (34 1/ 4)
C
120 (4 47/64)
150 (5 29/32)
237 (9 21/64)
294 (11 37/64)
Fit so that the arrow marks on the wall hanging bracket point upward.
If the wall consists of a material such as concrete and bolts or nuts must be
embedded beforehand, determine the hole positions by aligning using the actual
wall hanging bracket, or calculate hole positions based on the dimension drawing,
and then embed "M6" bolts or nuts. When embedding bolts, locate so that the bolts
protrude from the wall by 10 to 15 mm (25/64 to 19/32 inches).
(1) Fasten the screw at the top center hole first.
(2) Using a level, correct any bracket inclination, and then fasten screws at the
remaining 5 locations.
Note Use commercially available M6 screws suited to the wall surface material
(wood, steel frame, concrete etc.) for fitting the bracket to the wall.
2003
(1)
Lock bracket
fastening hole
Wall hanging
bracket
Lock
bracket
Red screw for
open/close
fastening
Lock bracket
(3)
(2)
(2)
Lower
insulation
spacer
Lower hole
TQZH498
Insulation spacer
(2)
Fitting hole
for red screw
for open/close
fastening
Red screw
for open/close
fastening
(3)
Lock bracket
fastening hole
Wall hanging
bracket
Wall
Terminal
cover
Flathead screwdriver
(1) Remove the screws for unit fastening (1 each on the left
and right) that are fitted to the wall hanging bracket sides.
(2) While lifting the bottom of the plasma TV unit, pull it
towards yourself.
(3) When the lower insulation spacers are freed, keep lifting
upward.
Note
Wall hanging
bracket
Plasma TV
Plasma TV
fastening screw
Fitting hole
for plasma
TV fastening
screw
Upper notch
Plasma TV
Wall
(1) Remove the terminal cover on the plasma TV (PX20 series only).
(2) Using a flathead screwdriver, remove the four caps
from the plasma TV.
* Carefully retain the removed terminal cover and
caps in a safe place. (They will be needed again
later should it be required to use the specialpurpose stand or standalone stand.)
(3) Using the included Allen wrench, fit the included
Allen head countersunk screws, dished tooth
Caps
washers and insulation spacers (4 sets) into the
holes from where the caps were removed. (See
the diagram at right.)
Place the plasma TV unit face down on a blanket or other soft cloth that is clean and free of debris, and follow the procedure below.
(1)
Wall hanging
bracket
Wall
(1) Remove the red screws for open/close fastening (one each
on the left and right) .
(2) Raise the plasma TV towards yourself, as shown in the
diagram at right, push up the lock bracket in the arrow
direction (upward), check that the bracket has locked, and
tentatively fasten. Securely fasten the red screw for
open/close fastening (one screw on left side)
to the lock
bracket fastening hole .
(3) After the above preparation, wire to equipment.
Wall
Wall attachment
holes (at 6 points)
A
775 (30 33/64)
735 (28 15/16)
660 (25 63/64)
* Provide spacing for the plasma TV of at least 100 mm (3 15/16 inches) to the top
and right side, at least 300 mm (11 13/16 inches) to the left side, at least 60 mm
(2 23/64 inches) to the bottom and at least 20 mm (25/32 inches) to the rear.
23 (29/32)
Before commencing work, carefully read these Instructions and the Manual for the wide plasma display to ensure
that fitting is performed correctly.
(Please save these instructions. You may need them when maintaining or moving the bracket.)
Wall
Model name
TH-37PA20
TH-42PA20
TH-42PX20
TH-50PX20
Note
The weight of the wall hanging bracket is approximately 7 kg (15 lb.). The plasma TV unit attached to the wall hanging
bracket weighs approximately 30 to 56 kg (66 to 123 lb.).
Check the wall strength at the 6 attachment locations by referring to the dimension drawing of the wall hanging bracket
(given at right), and provide adequate reinforcement if strength is not sufficient.
Fitting procedure
Fitting Instructions
Wall
11
(7/16)
Wall
Wall
Forbidden
The picture shown is for illustrative purposely only and may differ slightly from the actual product.
Forbidden
Forbidden
Caution
Forbidden
Warning
The type of action associated with each precaution is indicated using the pictographs shown below
(example pictographs).
Warning
Caution
The labels shown below indicate the severity of the danger or equipment damage that may occur if a
precaution or warning is ignored and the product is used incorrectly.
The following precautions must be followed in order to prevent danger to the user or other people, as well as
equipment damage.
Safety precautions
may cause heat to build up inside the plasma TV, resulting in malfunction.
TQZH498
Ensure good air flow so that the equipment ambient temperature does not exceed 40C. Failure to do this
For the TV power supply plug, use a power supply outlet that can be reached easily.
Use commercially available M6 screws suited to the wall surface material (wood, steel frame, concrete etc.)
The equipment has a lock mechanism on the left side, so provide at least 300 mm (11 13/16 inches) of
The wall hanging bracket is for use in attaching a plasma TV unit to a vertical wall for viewing. Do not fit to
1) Exercise care when selecting the location for the TV because it may discolor or deform due to light or heat if it is
placed where it is exposed to direct sunlight, or near a heater.
2) Upkeep
Wipe with a dry cloth. If the unit is extremely soiled, first wipe off soiling with a neutral detergent diluted in water, and
then wipe with a dry cloth. Do not use cleaners such as benzene, thinner or furniture wax because they may cause
paint peeling. (If using a chemical wiping cloth, follow any precautions included.)
3) Do not affix adhesive tape or stickers. Doing so may dirty the surface of the wall mounting bracket.
Insulation spacers
. . . x4
Allen wrench
( included tool ) . . . x1
TY-WK42PV3U
Components