Documente Academic
Documente Profesional
Documente Cultură
3. A microcomputer has a 64 K memory. What is the hexadecimal notation for the first memory
location?
A. 0000
B. FFFF
C. 0FFF
D. 3FFF
Answer: Option A
Explanation:
No answer description available for this question. Let us discuss.
View Answer Discuss in Forum Workspace Report
D. 64
Answer: Option B
Explanation:
No answer description available for this question. Let us discuss.
View Answer Discuss in Forum Workspace Report
8. The multiplication time for 10-bit numbers with 1 MHz clock will be
A. 32 sec
B. 20 sec
C. 21 sec
D. 22 sec
Answer: Option D
Explanation:
No answer description available for this question. Let us discuss.
View Answer Discuss in Forum Workspace Report
9. The initial state of MOD-16 down counter is 011. After 37 clock pulses, the state of the counter
will be
A. 1011
B. 0110
C. 0101
D. 0001
Answer: Option C
Explanation:
No answer description available for this question. Let us discuss.
View Answer Discuss in Forum Workspace Report
10. In a 4 bit weighted resistor D/A converter, resistor value corresponding to LSB is 32 k ohm. The
resistor value corresponding to MSB is
A. 32 k ohm
B. 16 k ohm
C. 8 k ohm
D. 4 k ohm
Answer: Option D
Explanation:
No answer description available for this question. Let us discuss.
11. Full adder circuit can be implemented by
A. Multiplexers
B. Half adders
C. AND or OR gates
D. Decoders
Answer: Option A
Explanation:
No answer description available for this question. Let us discuss.
View Answer Discuss in Forum Workspace Report
15. The ALU carrier out arithmetic and logic operations (OR AND, NOT, etc.) it processes
A. decimal numbers
B. binary numbers
C. hexadecimal numbers
D. octal numbers
Answer: Option B
Explanation:
No answer description available for this question. Let us discuss.
16. The total number of fundamental products of three variables is
A. 3
B. 5
C. 8
D. 16
Answer: Option C
Explanation:
No answer description available for this question. Let us discuss.
View Answer Discuss in Forum Workspace Report
20. Four memory chips of 16 x 4 size have their address buses connected together. This system will
be of size
A. 64 x 4
B. 16 x 16
C. 32 x 8
D. 256 x 1
Answer: Option B
Explanation:
No answer description available for this question. Let us discuss.
21. A ripple counter has propagation delay.
A. True
B. False
Answer: Option A
Explanation:
No answer description available for this question. Let us discuss.
View Answer Discuss in Forum Workspace Report
24. In 8085 microprocessor, which of the following interrupts has the lowest priority?
A. RST 5.5
B. RST 7.5
C. TRAP
D. INTR
Answer: Option A
Explanation:
No answer description available for this question. Let us discuss.
View Answer Discuss in Forum Workspace Report
28. Vectored interrupt is an interrupt that takes the program to a vector location. TRAP vectors to
0024 FI, RST 7.5 to 003 CH, RST 6.5 to 0034 H and
A. RST 5.5
B. RST 6.5
C. 24 H to 48 H
D. RST 5.5 to 002 CH
Answer: Option D
Explanation:
No answer description available for this question. Let us discuss.
View Answer Discuss in Forum Workspace Report
B. LSB last
C. 1
D. none of these
Answer: Option A
Explanation:
No answer description available for this question. Let us discuss.
31. A 3 bit synchronous counter uses FF with propagation delay time of 20 ns each. The maximum
possible time required for change of state will be.
A. 60 ns
B. 40 ns
C. 20 ns
D. None
Answer: Option B
Explanation:
No answer description available for this question. Let us discuss.
View Answer Discuss in Forum Workspace Report
38. How many JK flip-flops are needed to make a 4-bit shift register?
A. 2
B. 4
C. 6
D. 8
Answer: Option B
Explanation:
No answer description available for this question. Let us discuss.
39. A 10 MHz square wave clocks 5 bit ripple counter. The frequency of the 3rd FF output is
A. 2 MHz
B. 1.25 MHz
C. 50 MHz
D. 615 kHz
Answer: Option B
Explanation:
No answer description available for this question. Let us discuss.
View Answer Discuss in Forum Workspace Report
D. NOR gates
Answer: Option C
Explanation:
No answer description available for this question. Let us discuss.
View Answer Discuss in Forum Workspace Report
B. 64 K
C. 256 K
D. 512 K
Answer: Option B
Explanation:
No answer description available for this question. Let us discuss.
View Answer Discuss in Forum Workspace Report
47. Gray code is used in devices which convert analog quantities to digital signal because it is
A. more error free
B. much simpler than binary code
C. superior to Excess-3 code
D. absolutely error free
Answer: Option A
Explanation:
No answer description available for this question. Let us discuss.
View Answer Discuss in Forum Workspace Report