Documente Academic
Documente Profesional
Documente Cultură
126
INA
INA
126
INA
212
212
INA126
INA2126
6
INA
212
6
MicroPOWER
INSTRUMENTATION AMPLIFIER
Single and Dual Versions
FEATURES
DESCRIPTION
APPLICATIONS
INDUSTRIAL SENSOR AMPLIFIER:
Bridge, RTD, Thermocouple
PHYSIOLOGICAL AMPLIFIER:
ECG, EEG, EMG
MULTI-CHANNEL DATA ACQUISITION
PORTABLE, BATTERY OPERATED SYSTEMS
The INA126 and INA2126 are precision instrumentation amplifiers for accurate, low noise differential signal acquisition. Their
two-op-amp design provides excellent performance with very
low quiescent current (175A/channel). This, combined with a
wide operating voltage range of 1.35V to 18V, makes them
ideal for portable instrumentation and data acquisition systems.
Gain can be set from 5V/V to 10000V/V with a single
external resistor. Laser trimmed input circuitry provides low
offset voltage (250V max), low offset voltage drift (3V/C
max) and excellent common-mode rejection.
Single version package options include 8-pin plastic DIP,
SO-8 surface mount, and fine-pitch MSOP-8 surface-mount.
Dual version is available in the space-saving SSOP-16 finepitch surface mount, SO-16, and 16-pin DIP. All are specified
for the 40C to +85C industrial temperature range.
V+
INA2126
2
+
VIN
9
6
+
) G
VO = (VIN VIN
G=5+
3
40k
V+
80k
RG
10k
RG
INA126
+
VIN
3
6
8
10k
+ V) G
VO = (VIN
IN
40k
G=5+
80k
RG
10k
+
VIN
RG
VIN
10k
40k
15
11
14
40k
G=5+
10k
VIN
+ V ) G
VO = (VIN
IN
10
80k
RG
RG
2
40k
13
VIN
16
8
10k
40k
12
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
All trademarks are the property of their respective owners.
Copyright 1996-2005, Texas Instruments Incorporated
www.ti.com
ELECTROSTATIC
DISCHARGE SENSITIVITY
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling
and installation procedures can cause damage.
ESD damage can range from subtle performance degradation
to complete device failure. Precision integrated circuits may be
more susceptible to damage because very small parametric
changes could cause the device not to meet its published
specifications.
PACKAGE/ORDERING INFORMATION
RG
RG
VIN
V+
+
IN
VO
Ref
PACKAGE-LEAD
PACKAGE
MARKING
INA126PA
INA126P
DIP-8
DIP-8
INA126PA
INA126P
INA126UA
INA126U
SO-8
SO-8
INA126UA
INA126U
MSOP-8
A26(3)
PRODUCT
Single
INA126EA(2)
"
"
"
MSOP-8
A26(3)
"
"
INA2126PA
INA2126P
DIP-16
DIP-16
INA2126PA
INA2126P
SO-16
SO-16
INA2126UA
INA2126U
SSOP-16
INA2126EA
INA126E(2)
"
Top View
Dual
VINA
16 VINB
+
VINA
+
15 VINB
INA2126UA
INA2126U
RGA
14 RGB
INA2126EA(2)
RGA
13 RGB
RefA
12 RefB
VOA
11 VOB
SenseA
10 SenseB
"
INA2126E(2)
"
"
"
SSOP-16
INA2126E
"
"
NOTES: (1) For the most current package and ordering information, see the
Package Option Addendum at the end of this document, or see the TI website
at www.ti.com. (2) MSOP-8 and SSOP-16 packages are available only on 250
or 2500 piece reels. (3) Grade designation is marked on reel.
V+
INA126, INA2126
www.ti.com
SBOS062A
ELECTRICAL CHARACTERISTICS
At TA = +25C, VS = 15V, RL = 25k, unless otherwise noted.
INA126P, U, E
INA2126P, U, E
PARAMETER
INPUT
Offset Voltage, RTI
vs Temperature
vs Power Supply (PSRR)
Input Impedance
Safe Input Voltage
Common-Mode Voltage Range
Channel Separation (dual)
Common-Mode Rejection
INA2126U (dual SO-16)
CONDITIONS
MIN
VS = 1.35V to 18V
RS = 0
RS = 1k
VO = 0V
G = 5, dc
RS = 0, VCM = 11.25V
(V)0.5
(V)10
11.25
83
80
FREQUENCY RESPONSE
Bandwidth, 3dB
Slew Rate
Settling Time, 0.01%
Overload Recovery
POWER SUPPLY
Voltage Range
Current (per channel)
TEMPERATURE RANGE
Specification Range
Operation Range
Storage Range
Thermal Resistance, JA
8-Pin DIP
SO-8 Surface-Mount
MSOP-8 Surface-Mount
16-Pin DIP (dual)
SO-16 (dual)
SSOP-16 (dual)
TYP
MAX
100
0.5
5
109 || 4
250
3
15
(V+)+0.5
(V+)+10
11.5
130
94
94
10
30
0.5
10
MIN
VO = 14V, G = 5
G=5
VO = 12V, G = 100
G = 100
G = 100, VO = 14V
G=5
G = 100
G = 500
VO = 10V, G = 5
10V Step, G = 5
10V Step, G = 100
10V Step, G = 500
50% Input Overload
1.35
15
175
40
55
55
100
150
200
80
100
100
150
500
5
50
V
V/C
V/V
|| pF
V
V
V
dB
dB
dB
90
200
9
1.8
0.4
30
160
1500
4
IO = 0
UNITS
74
25
(V+)0.9 (V+)0.75
(V)+0.95 (V)+0.8
+10/5
1000
MAX
35
35
45
0.7
60
2
RL = 25k
RL = 25k
Short-Circuit to Ground
TYP
G = 5 to 10k
G = 5 + 80k/RG
0.02
0.1
2
10
0.2
0.5
25
100
0.002
0.012
NOISE
Voltage Noise, f = 1kHz
f = 100Hz
f = 10Hz
fB = 0.1Hz to 10Hz
Current Noise, f = 1kHz
fB = 0.1Hz to 10Hz
OUTPUT
Voltage, Positive
Negative
Short-Circuit Current
Capacitive Load Drive
INA126PA, UA, EA
INA2126PA, UA, EA
18
200
+85
+125
+125
50
5
0.18
nA
pA/C
nA
pA/C
V/V
V/V
%
ppm/C
%
ppm/C
%
nV/Hz
nV/Hz
nV/Hz
VPP
fA/Hz
pAPP
V
V
mA
pF
kHz
kHz
kHz
V/s
s
s
s
s
V
A
C
C
C
C/W
C/W
C/W
C/W
C/W
C/W
INA126, INA2126
SBOS062A
www.ti.com
TYPICAL CHARACTERISTICS
At TA = +25C and VS = 15V, unless otherwise noted.
GAIN vs FREQUENCY
70
110
G = 1000
100
60
Gain (dB)
50
G = 100
40
30
G = 20
20
G=5
10
0
90
80
70
G = 1000
60
50
G = 100
40
30
G=5
20
10
10
0
100
1k
10k
100k
1M
10
100
1k
10k
100k
Frequency (Hz)
Frequency (Hz)
120
1M
120
100
G = 1000
G = 100
80
60
40
G=5
20
100
0
100
1k
10k
G = 100
40
G=5
20
100k
1M
10
100k
VD/2
0
+15V
VD/2
VO
Ref
VCM
15V
10
Limited by A2
5
1M
text
tput swingsee
10
10k
10
15
15
1k
Frequency (Hz)
Limited by A2 ou
100
Frequency (Hz)
15
60
10
text
output swingsee
text
tput swingsee
Limited by A2 ou
4
3
VS = 5V
VS = +5V/0V
VREF = 2.5V
0
1
2
3
text
tput swingsee
Limited by A2 ou
4
5
10
15
G = 1000
80
INA126, INA2126
www.ti.com
SBOS062A
TYPICAL CHARACTERISTICS
(Cont.)
1000
1k
10
100
Current Noise
0.01%
Voltage Noise
100
10
10
1
10
100
1k
0.1%
100
10k
10
100
1k
Frequency (Hz)
Gain (V/V)
10
300
0.6
SR
4
2
(Noise)
0
2
4
6
0.5
+SR
200
0.4
150
VS = 1.35V
VS = 5V
IQ
100
50
0.3
0.2
0.1
8
10
10
75
50
25
25
50
75
Temperature (C)
100
0
125
V+
(V+)1
THD+N (%)
0.1
RL = 10k
0.01
Sourcing Current
(V+)2
(V)+2
(V)+1
RL = 100k
Sinking Current
G=5
0.001
V
10
100
1k
10k
INA126, INA2126
SBOS062A
Frequency (Hz)
www.ti.com
250
TYPICAL CHARACTERISTICS
(Cont.)
20mV/div
20mV/div
SMALL-SIGNAL RESPONSE, G = 5
50s/div
LARGE-SIGNAL RESPONSE, G = 5
5V/div
0.2V/div
50s/div
50s/div
500ms/div
G = 1000
Separation (dB)
140
130
G = 100
120
110
G=5
100
RL = 25k
90
Measurement limited
by amplifier or
measurement noise.
80
70
60
100
1k
10k
100k
1M
Frequency (Hz)
INA126, INA2126
www.ti.com
SBOS062A
APPLICATION INFORMATION
equation (1). Low resistor values required for high gain can
make wiring resistance important. Sockets add to the wiring
resistance, which will contribute additional gain error in
gains of approximately 100 or greater.
OFFSET TRIMMING
The INA126 and INA2126 are laser trimmed for low offset
voltage and offset voltage drift. Most applications require no
external offset adjustment. Figure 2 shows an optional circuit for trimming the output offset voltage. The voltage
applied to the Ref terminal is added to the output signal. An
op amp buffer is used to provide low impedance at the Ref
terminal to preserve good common-mode rejection.
VIN
80k
RG
RG
INA126
+
VIN
VO
V+
Ref
100A
1/2 REF200
(1)
OPA237
10mV
Adjustment Range
100
10k
100
100A
1/2 REF200
DESIRED GAIN
(V/V)
RG
()
NEAREST 1%
RG VALUE
5
10
20
50
100
200
500
1000
2000
5000
10000
NC
16k
5333
1779
842
410
162
80.4
40.1
16.0
8.0
NC
15.8k
5360
1780
845
412
162
80.6
40.2
15.8
7.87
7
INA126
3
+
VIN
A1
G = 5 + 80k
RG
40k
+ V) G
VO = (VIN
IN
10k
RG
10k
Load
VO
NC: No Connection.
VIN
A2
40k
5
Ref
+
VIN
4
0.1F
RG
VIN
INA126
VO
V
Ref
Dual version has
external sense connection.
INA126, INA2126
SBOS062A
www.ti.com
Microphone,
Hydrophone
etc.
INA126
47k
47k
Thermocouple
INA126
10k
INA126
Center-tap provides
bias current return.
(2)
INA126, INA2126
www.ti.com
SBOS062A
+5V
INA126
2.5V + V
A1
40k
R1
1k
2
10k
Bridge
Sensor
RG
C1
0.47F
10k
IN
R2
1k
A2
2.5V V
+IN
40k
1.2V
ADS7817
12-Bit
A/D
VREF
CS
Ck
Serial
Data
Chip
Select
Clock
33A
4
6 8
REF1004C-1.2
4
VIN
R1
RG
INA126
Ref
IB
IO =
A1
A1
IB Error
OPA177
OPA130
OPA602
OPA129
1.5nA
20pA
1pA
100fA
VIN
G
R1
IO
Load
INA126, INA2126
SBOS062A
www.ti.com
12-Jan-2007
PACKAGING INFORMATION
Orderable Device
Status (1)
Package
Type
Package
Drawing
INA126E/250
ACTIVE
MSOP
DGK
250
CU NIPDAU
Level-2-260C-1 YEAR
INA126E/250G4
ACTIVE
MSOP
DGK
250
CU NIPDAU
Level-2-260C-1 YEAR
INA126E/2K5
ACTIVE
MSOP
DGK
CU NIPDAU
Level-2-260C-1 YEAR
INA126E/2K5G4
ACTIVE
MSOP
DGK
CU NIPDAU
Level-2-260C-1 YEAR
INA126EA/250
ACTIVE
MSOP
DGK
250
CU NIPDAU
Level-2-260C-1 YEAR
INA126EA/250G4
ACTIVE
MSOP
DGK
250
CU NIPDAU
Level-2-260C-1 YEAR
INA126EA/2K5
ACTIVE
MSOP
DGK
CU NIPDAU
Level-2-260C-1 YEAR
INA126EA/2K5G4
ACTIVE
MSOP
DGK
CU NIPDAU
Level-2-260C-1 YEAR
INA126P
ACTIVE
PDIP
50
CU NIPDAU
INA126PA
ACTIVE
PDIP
50
CU NIPDAU
INA126PAG4
ACTIVE
PDIP
50
CU NIPDAU
INA126PG4
ACTIVE
PDIP
50
CU NIPDAU
INA126U
ACTIVE
SOIC
100
CU NIPDAU
Level-3-260C-168 HR
INA126U/2K5
ACTIVE
SOIC
CU NIPDAU
Level-3-260C-168 HR
INA126U/2K5G4
ACTIVE
SOIC
CU NIPDAU
Level-3-260C-168 HR
INA126UA
ACTIVE
SOIC
100
CU NIPDAU
Level-3-260C-168 HR
INA126UA/2K5
ACTIVE
SOIC
2500
Pb-Free
(RoHS)
CU NIPDAU
Level-3-260C-168 HR
INA126UA/2K5E4
ACTIVE
SOIC
2500
Pb-Free
(RoHS)
CU NIPDAU
Level-3-260C-168 HR
INA126UAG4
ACTIVE
SOIC
100
CU NIPDAU
Level-3-260C-168 HR
INA126UG4
ACTIVE
SOIC
100
CU NIPDAU
Level-3-260C-168 HR
INA2126E/250
ACTIVE
SSOP/
QSOP
DBQ
16
250
CU NIPDAU
Level-3-260C-168 HR
INA2126E/250G4
ACTIVE
SSOP/
QSOP
DBQ
16
250
CU NIPDAU
Level-3-260C-168 HR
INA2126E/2K5
ACTIVE
SSOP/
QSOP
DBQ
16
CU NIPDAU
Level-3-260C-168 HR
INA2126E/2K5G4
ACTIVE
SSOP/
QSOP
DBQ
16
CU NIPDAU
Level-3-260C-168 HR
INA2126EA/250
ACTIVE
SSOP/
QSOP
DBQ
16
250
CU NIPDAU
Level-3-260C-168 HR
Addendum-Page 1
Lead/Ball Finish
12-Jan-2007
Orderable Device
Status (1)
Package
Type
Package
Drawing
INA2126EA/250G4
ACTIVE
SSOP/
QSOP
DBQ
16
250
CU NIPDAU
Level-3-260C-168 HR
INA2126EA/2K5
ACTIVE
SSOP/
QSOP
DBQ
16
CU NIPDAU
Level-3-260C-168 HR
INA2126EA/2K5G4
ACTIVE
SSOP/
QSOP
DBQ
16
CU NIPDAU
Level-3-260C-168 HR
INA2126P
ACTIVE
PDIP
16
25
Call TI
INA2126PA
ACTIVE
PDIP
16
25
Call TI
INA2126PAG4
ACTIVE
PDIP
16
25
Call TI
INA2126PG4
ACTIVE
PDIP
16
25
Call TI
INA2126U
ACTIVE
SOIC
16
48
Pb-Free
(RoHS)
CU NIPDAU
Level-3-260C-168 HR
INA2126UA
ACTIVE
SOIC
16
48
CU NIPDAU
Level-3-260C-168 HR
INA2126UA/2K5
ACTIVE
SOIC
16
2500
Pb-Free
(RoHS)
CU NIPDAU
Level-3-260C-168 HR
INA2126UA/2K5E4
ACTIVE
SOIC
16
2500
Pb-Free
(RoHS)
CU NIPDAU
Level-3-260C-168 HR
INA2126UAE4
ACTIVE
SOIC
16
48
Pb-Free
(RoHS)
CU NIPDAU
Level-3-260C-168 HR
INA2126UAG4
ACTIVE
SOIC
16
48
CU NIPDAU
Level-3-260C-168 HR
INA2126UE4
ACTIVE
SOIC
16
48
Pb-Free
(RoHS)
CU NIPDAU
Level-3-260C-168 HR
SN200501036DRE4
ACTIVE
SOIC
16
2500
Pb-Free
(RoHS)
CU NIPDAU
Level-3-260C-168 HR
Lead/Ball Finish
(1)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
Addendum-Page 2
12-Jan-2007
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 3
MECHANICAL DATA
MPDI001A JANUARY 1995 REVISED JUNE 1999
P (R-PDIP-T8)
PLASTIC DUAL-IN-LINE
0.400 (10,60)
0.355 (9,02)
8
0.260 (6,60)
0.240 (6,10)
4
0.070 (1,78) MAX
0.325 (8,26)
0.300 (7,62)
0.015 (0,38)
Gage Plane
0.100 (2,54)
0.021 (0,53)
0.015 (0,38)
0.430 (10,92)
MAX
0.010 (0,25) M
4040082/D 05/98
NOTES: A. All linear dimensions are in inches (millimeters).
B. This drawing is subject to change without notice.
C. Falls within JEDEC MS-001
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications,
enhancements, improvements, and other changes to its products and services at any time and to
discontinue any product or service without notice. Customers should obtain the latest relevant information
before placing orders and should verify that such information is current and complete. All products are sold
subject to TIs terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in
accordance with TIs standard warranty. Testing and other quality control techniques are used to the extent
TI deems necessary to support this warranty. Except where mandated by government requirements, testing
of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible
for their products and applications using TI components. To minimize the risks associated with customer
products and applications, customers should provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent
right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine,
or process in which TI products or services are used. Information published by TI regarding third-party
products or services does not constitute a license from TI to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or
other intellectual property of the third party, or a license from TI under the patents or other intellectual
property of TI.
Reproduction of information in TI data books or data sheets is permissible only if reproduction is without
alteration and is accompanied by all associated warranties, conditions, limitations, and notices.
Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not
responsible or liable for such altered documentation.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for
that product or service voids all express and any implied warranties for the associated TI product or service
and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Following are URLs where you can obtain information on other Texas Instruments products and application
solutions:
Products
Applications
Amplifiers
amplifier.ti.com
Audio
www.ti.com/audio
Data Converters
dataconverter.ti.com
Automotive
www.ti.com/automotive
DSP
dsp.ti.com
Broadband
www.ti.com/broadband
Interface
interface.ti.com
Digital Control
www.ti.com/digitalcontrol
Logic
logic.ti.com
Military
www.ti.com/military
Power Mgmt
power.ti.com
Optical Networking
www.ti.com/opticalnetwork
Microcontrollers
microcontroller.ti.com
Security
www.ti.com/security
www.ti.com/lpw
Telephony
www.ti.com/telephony
Mailing Address:
www.ti.com/video
Wireless
www.ti.com/wireless
Texas Instruments
Post Office Box 655303 Dallas, Texas 75265
Copyright 2007, Texas Instruments Incorporated