Documente Academic
Documente Profesional
Documente Cultură
Format description
Change according to the actual information,the font is
green. egnetmask=your_mask the subnet mask is
255.255.255.0then filled in as:
netmask=255.255.255.0
Division of labor
According to the document, IDC technicians install the
system,and configure network Extranet can access to
each server,port 22
When it is done ,transfer to Powerall for configuration
checking.
And then IDC technician will change the network topology
and checked by Powerall again.
1. Rack hardware
2. Establish network connection
3. Configuration switch
4. Installing preparation
5. Build a RAID Array, raid 5 or raid 6
6. Motherboard set VT Enable in BIOS
7. Configuration iDRAC6 (integrated Dell Remote Access Card)
8. System Integration testing
9. Install system(Firewall)
10. Install system(Cserver)
11. Configure servers (check configuration by Powerall)
12. Reconstruct network
Notice:
<h3c>system
*NOTEItalics is switch's command
[h3c]sysname sw1
*NOTECommands for sw2 is sysname sw2
[sw1] interface Vlan-interface1
[sw1-vlan-interface1] ip address your_ip your_mask *NOTE:configurate sw1 to
remote control ip address
[sw1-vlan-interface1] quit
[sw1] ip route-static 0.0.0.0 0.0.0.0 your_gateway
[sw1] user-interface aux 0
[sw1-ui-aux0] authentication-mode password
[sw1-ui-aux0] user privilege level 3
[sw1-ui-aux0] set authentication password cipher password
[sw1-ui-aux0] history-command max-size 20
[sw1-ui-aux0] idle-timeout 5 0
[sw1-ui-aux0] screen-length 30
[sw1-ui-aux0] quit
[sw1]local-user admin
[sw1-luser-admin] password cipher password
[sw1-luser-admin] service-type ssh level 3
[sw1-luser-admin] quit
[sw1] public-key local create rsa
[sw1] public-key local create dsa
[sw1] user-interface vty 0 4
[sw1-ui-vty0-4] authentication-mode scheme
[sw1-ui-vty0-4] protocol inbound ssh
[sw1-ui-vty0-4] quit
Download the 2 ISO images below, check their md5 to ensure them are
error-free, then burn them to blank DVD disks respectively. (Note: the 2 ISO,
one for cloud firewall, the other for cloud server.)
ftp://imgsetup:powerall@ftp.goodvm.com/cloudinstall/CentOS_5.4_cloud.iso
( Used for cloud Server, R710. )
md5sum: ffc97cf0e7ae7016e20f96bf497cb687 CentOS_5.4_cloud.iso
ftp://imgsetup:powerall@ftp.goodvm.com/cloudinstallcustom/CENTOS_5.4_
CLOUD_R210_2_500G_SD.iso
md5: ce7f093037e2a725a4f5fc0d4e0f698e
CENTOS_5.4_CLOUD_R210_2_500G_SD.iso
( Used for cloud firewall, R210 )
Reboot server
*NOTEBrand Model server settings in different ways on different servers see the
user manual
Start the server from the corresponding DVD, youll see the
installation menu if everything goes well.
If the system installation is smooth going with no error. Try to login the system with the account
below.
username : root
password : cloud2010IDC
Modify the file below, configure DNS. ( Please do not use your local DNS server. )
[root@xxx ~]# cat /etc/resolv.conf
nameserver 203.131.233.141
nameserver 203.131.233.151
Make sure the 2 R210 can be accessed from Internet via the new IP Addresses.
If the system installation is smooth going with no error. Try to login the system with the
account below:
username : root
password : cloud2010IDC
Modify the file below, configure DNS. ( Please do not your local DNS Server.)
[root@xxx ~]# cat /etc/resolv.conf
nameserver 203.131.233.141
nameserver 203.131.233.151
After finishing all the servers installation, please fill the <>sent the
configure info. such as IP, DNS and so on to
xinqiang@powerallnetworks.com .
Email : xinqiang@powerallnetworks.com
Phone 86-0755-86593733
Power-All Networks Ltd. Cloud Center Network Connection Topology with iDRAC6.