Documente Academic
Documente Profesional
Documente Cultură
If a network has converged, what is true about the link-state database held by
each router in the same OSPF area?
Each router has a link-state database containing the same status information.
Each router has a different link-state database depending on its position
within the network.
The link-state database is stored in a designated router and is accessed by
each router in the area as needed.
The link-state database in each router only contains information about
adjacent routers and the status of their links.
Refer to the exhibit. RTRC was recently configured and is not sending the
proper OSPF routes to RTRB, as shown in the RTRB routing table. Based on the
RTRC configuration, what is most likely the problem?
RTRC interfaces are administratively shut down.
The OSPF process ID for RTRC does not match the process ID used on
RTRB.
The interface addresses on RTRC overlap with other addresses in the
network.
The OSPF routing configuration on RTRC has a missing or incorrect
network statement.
What is the primary difference between link-state protocols and distance vector
protocols with regard to route calculation?
Distance vector protocols take existing routes from their neighbors and add
to them. Link-state protocols independently calculate full routes
Link-state protocols calculate and pass full routing tables to all routers in
their associated areas, and distance vector protocols do not.
When determining invalid routes, link-state protocols use split horizon for all
route computations. Distance vector protocols use reverse poisoning
Distance vector protocols require more CPU and RAM for route calculations
than link-state protocols require.
Refer to the exhibit. The network administrator would like only the 172.16.32.0
network advertised to Router1. Which OSPF network command accomplishes
this?
Router2(config-router)# network 172.16.0.0 0.0.0.15 area 0
Refer to the exhibit. Routers A, B, and C are part of the existing OSPF network.
Router D has been added to the network. All routers are running OSPF and have
the indicated priorities applied to the interface. What is the DR/BDR status
immediately after router D is added to the existing network?
An election is forced and router D wins the DR election.
The DR and BDR do not change until the next election.
The router with the highest router ID becomes the new BDR.
Refer to the exhibit. Which router will be elected the DR and which will become
the BDR?
R1 will be DR and R2 will be BDR.
R1 will be DR and R3 will be BDR.
The router with the highest OSPF priority setting wins the election for DR.
The default priority value for a router connected to a multi-access network is
0.
The router with the highest MAC address is elected as the DR when the
default priority values are used.
Refer to the exhibit. What is the purpose of the configuration commands added
on router B?
allows router A to form an adjacency with router B
10.11.0.2
10.11.0.255
224.0.0.5
255.255.255.255
Refer to the exhibit. What statement describes the DR/BDR relationship of the
HQ router?
HQ is the DR.
HQ is the BDR.
HQ is a DROTHER.
Refer to the exhibit. Which network statement configures the home router to
allow all the interfaces to participate in OSPF?
network 10.0.0.0 0.3.255.255 area 0
What range of networks are advertised in the OSPF updates by the command
Router1(config-router)# network 192.168.0.0 0.0.15.255 area 0?
192.168.0.0/24 through 192.168.0.15/24
Which two features are associated with Frame Relay OSPF point-to-multipoint
environments? (Choose two.)
A DR is not elected.
The OSPF priority value determines the active DR on the Frame Relay link.
The BDR will have a router ID whose value is greater than the DR router ID.
Refer to the exhibit. How was the OSPF default gateway entry for R2
determined?
Default routes are automatically injected by OSPF into all advertisements.
The value set for the Transmit Delay time on both routers is too low.
Refer to the exhibit. What is the purpose of the value 128 shown in bold?
It is the OSPF cost metric.
Refer to the exhibit. A network administrator has implemented OSPF and the
network has converged. If all router interfaces are enabled and functional, what
route will OSPF view as lowest cost when moving frames from Host3 to Host1?
R3 to R4 to R1
R3 to R1
R3 to R2 to R1
R3 to R5 to R2 to R1