Documente Academic
Documente Profesional
Documente Cultură
RF and Microwave
Signal Generator
Specifications
SMB100A_dat-sw_en_5213-8396-22_v0900_cover.indd 1
year
14.07.2016 19:10:02
CONTENTS
Definitions ....................................................................................................................................................................... 3
Specifications .................................................................................................................................................................. 4
Hardware and software option concept .............................................................................................................................................. 4
RF performance................................................................................................................................................................................. 4
Frequency ...................................................................................................................................................................................... 4
Frequency sweep ........................................................................................................................................................................... 5
Reference frequency ...................................................................................................................................................................... 5
Level.................................................................................................................................................................................................. 6
Level settings ................................................................................................................................................................................. 6
Level performance ......................................................................................................................................................................... 7
Level setting times ......................................................................................................................................................................... 8
Reverse power ............................................................................................................................................................................... 8
VSWR ............................................................................................................................................................................................ 8
Level sweep ................................................................................................................................................................................. 12
Spectral purity ................................................................................................................................................................................. 13
List mode settings............................................................................................................................................................................ 18
Analog modulation ........................................................................................................................................................................... 19
Simultaneous modulation ............................................................................................................................................................. 19
Amplitude modulation................................................................................................................................................................... 19
Frequency bands for frequency and phase modulation ................................................................................................................ 19
Frequency modulation .................................................................................................................................................................. 20
Phase modulation ........................................................................................................................................................................ 21
Pulse modulation (R&SSMB-K21 or R&SSMB-K22 option) ....................................................................................................... 22
Input for external modulation signals ............................................................................................................................................ 23
Modulation sources ......................................................................................................................................................................... 24
Internal modulation generator (LF) ............................................................................................................................................... 24
LF frequency sweep ..................................................................................................................................................................... 24
Pulse generator (R&SSMB-K23 option) ...................................................................................................................................... 25
Pulse train (R&SSMB-K27 option) .............................................................................................................................................. 25
Stereo/RDS coder (R&SSMB-B5 option) .................................................................................................................................... 26
Remote control ................................................................................................................................................................................ 27
Connectors ...................................................................................................................................................................................... 28
Front panel connectors................................................................................................................................................................. 28
Rear panel connectors ................................................................................................................................................................. 28
General data.................................................................................................................................................................................... 29
Definitions
General
Product data applies under the following conditions:
Device settings and GUI parameters are designated with the format parameter: value.
Typical data as well as nominal and measured values are not warranted by Rohde & Schwarz.
Specifications
Hardware and software option concept
The available frequency ranges and the corresponding hardware and software options are shown in the tables.
standard
R&SSMB-B1
R&SSMB-B1H
9 kHz to 6 GHz
R&SSMB-B106
R&SSMB-B120
R&SSMB-B131
R&SSMB-B112L
standard
R&SSMB-B1
R&SSMB-B1H
R&SSMB-B120L
R&SSMB-B31
R&SSMB-B25
R&SSMB-B32
R&SSMB-B26
R&SSMB-B140,
R&SSMB-B140N
R&SSMB-B140L
R&SSMB-B32
R&SSMB-B26
R&SSMB-B30
R&SSMB-K21
R&SSMB-K23
R&SSMB-K27
standard
R&SSMB-B5
R&SSMB-K22
R&SSMB-K23
R&SSMB-K27
RF performance
Frequency
Range
R&SSMB-B101
R&SSMB-B102
R&SSMB-B103
R&SSMB-B106
R&SSMB-B112, R&SSMB-B112L
R&SSMB-B120, R&SSMB-B120L
R&SSMB-B131
R&SSMB-B140, R&SSMB-B140L,
R&SSMB-B140N
Resolution of setting
Resolution of synthesis
Setting time
0.001 Hz
f = 1 GHz
0.44 Hz (nom.)
to within < 1 107 for f > 200 MHz or < 20 Hz for f 200 MHz
Specification does not apply when frequency crosses 20 GHz.
Specification does not apply to instruments equipped with R&SSMB-B120/-B131/-B140 when
frequency crosses 200 kHz.
after IEC/IEEE bus delimiter
ALC state on
< 3 ms
ALC state sample&hold, f 20 GHz
< 7 ms
ALC state sample&hold, f > 20 GHz
< 10 ms
after trigger pulse in list mode
< 1 ms
0.1
1
2
Frequency sweep
Operating mode
Trigger mode
Trigger source
Trigger slope
Sweep range
Sweep shape
Step spacing
Step size
free run
full sweep
execute one step
external trigger only
linear
logarithmic
Reference frequency
Frequency error
Aging
(after 10 days of uninterrupted operation)
Temperature effect (0 C to +50 C)
Warm-up time
Reference frequency output
Connector type
Output frequency
Output level
Source impedance
Reference frequency input
Connector type
Input frequency
Frequency locking range
Input level range
Input impedance
< 1 107
< 1 108
< 1 106/year
< 1 109/day, < 1 107/year
< 5 1010/day, < 3 108/year
< 2 106
< 1 107
< 1 108
10 min
BNC female
BNC female
5 MHz, 10 MHz
3 106
0 dBm to +16 dBm
50 (nom.)
10 MHz
applied external reference frequency
+7 dBm to +13 dBm, +10 dBm (typ.)
50 (nom.)
Level
General explanations
Instruments equipped with R&SSMB-B101/-B102/-B103/-B106/-B112 frequency options include an electronic step attenuator with
step ranges of 5 dB (6 dB with R&SSMB-B112). Instruments equipped with R&SSMB-B120/-B131/-B140 frequency options include
a mechanical step attenuator. Instruments equipped with R&S SMB-B112L/-B120L/-B140L frequency options do not include a step
attenuator. These instruments have a limited level setting range and a limited specified level range.
Level setting modes
The R&SSMB100A offers two different operating modes for level setting:
AUTO MODE: The step attenuator is switched automatically
FIXED MODE: The level is set without switching the step attenuator. The step attenuator is fixed to the current setting. If ALC is on,
level changes are performed without interruption. The maximum interruption-free setting range is limited
ALC modes
The R&SSMB100A offers different ALC modes:
ALC STATE AUTO: The best suited ALC mode is set automatically
ALC STATE on: The level control loop is closed. This mode is suitable for CW, AM, FM and M
ALC STATE SAMPLE&HOLD (S&H): At every frequency and level change, the level control loop is closed for about 1 ms and the
level control voltage is sampled. The level control voltage is then clamped. This mode is used internally while in ALC state AUTO
for pulse modulation
During a S&H measurement the level is decreased by 30 dB for instruments with electronic step attenuator. For instruments with
mechanical attenuator or without step attenuator, the set on level is present for approximately 2 ms during a S&H procedure after level
or frequency setting or after switching RF on.
Level settings
Setting range
R&SSMB-B101/-B102/-B103/-B106
R&SSMB-B112
R&SSMB-B112L
R&SSMB-B120/R&SSMB-B131,
R&SSMB-B140/R&SSMB-B140N
R&SSMB-B120L/R&SSMB-B140L
Resolution of setting
Interruption-free level setting range
6
Level performance
Specified level range, peak envelope power (PEP)
R&SSMB-B101/-B102/-B103/-B106
9 kHz f 200 kHz
200 kHz < f 1 MHz
1 MHz < f 6 GHz
R&SSMB-B112
standard
200 kHz < f 1 MHz
1 MHz < f 12.75 GHz
with R&SSMB-B30 option
200 kHz < f 1 MHz
1 MHz < f 12.75 GHz
R&SSMB-B112L
standard
200 kHz < f 1 MHz
1 MHz < f 12.75 GHz
with R&SSMB-B30 option
200 kHz < f 1 MHz
1 MHz < f 12.75 GHz
R&SSMB-B120
standard
200 kHz < f 10 MHz
10 MHz < f 50 MHz
50 MHz < f 20 GHz
with R&SSMB-B31 option 3
200 kHz < f 10 MHz
10 MHz < f 50 MHz
50 MHz < f 20 GHz
R&SSMB-B120L
standard
200 kHz < f 10 MHz
10 MHz < f 50 MHz
50 MHz < f 20 GHz
with R&SSMB-B31 option 3
200 kHz < f 10 MHz
10 MHz < f 50 MHz
50 MHz < f 100 MHz
100 MHz < f 20 GHz
R&SSMB-B131
standard
200 kHz < f 10 MHz
10 MHz < f 31.8 GHz
with R&SSMB-B32 option 3
200 kHz < f 10 MHz
10 MHz < f 50 MHz
50 MHz < f 31.8 GHz
R&SSMB-B140,
standard
R&SSMB-B140N
200 kHz < f 10 MHz
10 MHz < f 40 GHz
with R&SSMB-B32 option 3
200 kHz < f 10 MHz
10 MHz < f 50 MHz
50 MHz < f 40 GHz
R&SSMB-B140L
standard
200 kHz < f 10 MHz
10 MHz < f 50 MHz
50 MHz < f 40 GHz
with R&SSMB-B32 option 3
200 kHz < f 10 MHz
10 MHz < f 50 MHz
50 MHz < f 40 GHz
For instruments equipped with R&SSMB-B25 or R&SSMB-B26 option, the specification is valid with low harmonic filter off.
With low harmonic filter on, the standard level range is valid.
Level error
R&SSMB-B101/-B102/-B103/
-B106/-B112
R&SSMB-B112L
R&SSMB-B120L/-B140L
R&SSMB-B120/-B131,
R&SSMB-B140/-B140N
level 90 dBm
< 0.5 dB
< 1.2 dB
< 1.5 dB
level deviation < 0.1 dB 5 from final value, with GUI update stopped, temperature range
+18 C to +33 C, without switching of the mechanical step attenuator
after IEC/IEEE bus delimiter
ALC state on
< 2.5 ms
ALC state S&H, f 20 GHz
< 7 ms
ALC state S&H, f > 20 GHz
< 10 ms
in list mode after trigger pulse
< 1 ms
with switching of the mechanical step attenuator
ALC state on
< 25 ms
ALC state S&H
< 30 ms
Reverse power
The R&SSMB100A equipped with R&SSMB-B101/-B102/-B103/-B106 frequency options includes a reverse power protection as
standard. For instruments equipped with the R&SSMB-B112 or R&SSMB-B112L frequency option, a reverse power protection
option (R&SSMB-B30) is available.
Maximum permissible RF power in output frequency range of RF path for f > 1 MHz, from source 50
Instruments with reverse power protection
Reverse power
1 MHz < f 1 GHz
50 W
1 GHz < f 2 GHz
25 W
2 GHz < f 12.75 GHz
10 W
Maximum permissible DC voltage
35 V
Instruments without reverse power protection
Reverse power
0.5 W
Maximum permissible DC voltage
R&SSMB-B112/-B112L
35 V
R&SSMB-B120/-B120L,
0V
R&SSMB-B131,
R&SSMB-B140/-B140L/-B140N
VSWR
Output impedance VSWR in 50 system, ALC state on
R&SSMB-B101/-B102/-B103/-B106/
f > 200 kHz
-B112
R&SSMB-B112L/-B30
f > 200 kHz
R&SSMB-B120/-B131,
1 MHz < f 20 GHz
R&SSMB -B140/-B140N
20 GHz < f 40 GHz
4
5
< 1.8
< 2.0
< 1.6 (meas.)
< 1.8 (meas.)
Only for instruments equipped with an R&SSMB-B101, R&SSMB-B102, R&SSMB-B103 or R&SSMB-B106 option.
Level deviation < 0.25 dB for f 23.4375 MHz for instruments equipped with an R&SSMB-B112/-B112L/-B120/-B120L/-B131/-B140/-B140L/-B140N
option
Maximum available output level versus frequency, Low Harmonic Filter off and on (meas.).
10
11
Level sweep
Operating mode
Trigger mode
free run
full sweep
execute one step
external trigger only
Trigger source
Trigger slope
Sweep range
Sweep shape
Step spacing
Step size setting resolution
Dwell time setting range
Dwell time setting resolution
12
Spectral purity
Harmonics
R&SSMB-B101/-B102/-B103/-B106/
-B112/-B112L
R&SSMB-B120/-B120L/-B131,
R&SSMB-B140/-B140L/-B140N
Nonharmonics
Subharmonics
Wideband noise
RMS jitter
Residual FM
Residual AM
13
0
Harmonic 2f
Harmonic 3f
-10
-20
Harmonics / dBc
-30
-40
-50
-60
-70
-80
0,00
1,00
2,00
3,00
4,00
5,00
6,00
Harmonics versus carrier frequency at +15 dBm output level with R&SSMB-B106 option (meas.).
0
Harmonic 2f
Harmonic 3f
-10
-20
Harmonics / dBc
-30
-40
-50
-60
-70
-80
0,00
2,00
4,00
6,00
8,00
10,00
12,00
Harmonics versus carrier frequency at +15 dBm output level with R&SSMB-B112 option (meas.).
14
0
Harmonic 2f
Harmonic 3f
-10
-20
Harmonics / dBc
-30
-40
-50
-60
-70
-80
0,00
2,00
4,00
6,00
8,00
10,00
12,00
14,00
16,00
18,00
20,00
Harmonics versus carrier frequency at +8 dBm output level with R&SSMB-B140 option (meas.).
0
Harmonic 2f
Harmonic 3f
-10
-20
Harmonics / dBc
-30
-40
-50
-60
-70
-80
0,00
2,00
4,00
6,00
8,00
10,00
12,00
14,00
16,00
18,00
20,00
Harmonics versus carrier frequency at +13 dBm output level with R&SSMB-B140 option and R&SSMB-B32 (meas.).
15
0
Harmonic 2f
Harmonic 3f
-10
-20
Harmonics / dBc
-30
-40
-50
-60
-70
-80
0,00
5,00
10,00
15,00
20,00
25,00
30,00
Harmonics versus carrier frequency at +10 dBm output level with R&SSMB-B140 option,
R&SSMB-B32 and R&SSMB-B26, low harmonic filter on (meas.).
16
35,00
Measured SSB phase noise with R&SSMB-B1H OCXO option for the 1/2/3/6 GHz model.
Measured SSB phase noise with R&SSMB-B1H OCXO option for the 12.75/20/40 GHz model.
Measured SSB phase noise, f = 1 GHz, comparison with standard internal reference,
R&SSMB-B1 OCXO option, R&SSMB-B1H OCXO option and residual phase noise.
17
Trigger source
Max. number of stored settings
Dwell time setting range
Dwell time setting resolution
Setting time
18
free run
full sweep
execute one step
automatic
single
step
keyboard, external trigger, remote control
2000
1 ms to 1 s
0.1 ms
see frequency and level data
Analog modulation
Simultaneous modulation
Amplitude modulation
Amplitude modulation
Frequency modulation
Phase modulation
Pulse modulation
()
Frequency modulation
Phase modulation
Pulse modulation
()
= compatible
= incompatible
() = compatible with limitations: No specification applies to AM distortion, AM depth error and on/off ratio with pulse modulation.
Amplitude modulation
For f 200 kHz, level setting mode auto, AM envelope within specified level range.
Modulation source
External coupling
AM depth setting range
Resolution of setting
AM depth (m) error
AM distortion
Synchronous M at AM
0.1 %
fmod = 1 kHz and m < 80 %
R&SSMB-B101/-B102/-B103/-B106
f 23.4375 MHz
< (1 % of setting + 1 %)
f > 23.4375 MHz
< (4 % of setting + 1 %)
R&SSMB-B112/-B112L/-B120/-B120L/-B131/-B140/-B140L/-B140N
f > 1 MHz, PEP 15 dBm 7, 8
< (4 % of setting + 1 %)
fmod = 1 kHz
m = 30 %
m = 80 %
R&SSMB-B101/-B102/-B103/-B106
f 23.4375 MHz
< 0.25 %
< 0.5 %
f > 23.4375 MHz
< 1.5 %
<3%
R&SSMB-B112/-B112L/-B120/-B120L
f > 5 MHz, PEP 15 dBm 7
< 1.5 %
<3%
R&SSMB-B131/-B140/-B140L/-B140N
5 MHz < f 20 GHz,
< 1.5 %
<3%
PEP 13 dBm 7
20 GHz < f 40 GHz,
<2%
<4%
PEP 10 dBm 7, 8
m = 60 %,
< 3 dB
DC coupling: 0 Hz to 50 kHz,
AC coupling: 10 Hz to 50 kHz
m = 30 %, fmod = 1 kHz, peak/2
f 20 GHz
< 0.2 rad
20 GHz < f 40 GHz
< 0.4 rad
7
8
f 23.4375 MHz
23.4375 MHz < f 46.875 MHz
46.875 MHz < f 93.75 MHz
93.75 MHz < f 187.5 MHz
187.5 MHz < f 375 MHz
375 MHz < f 750 MHz
750 MHz < f 1500 MHz
1500 MHz < f 3 GHz
3 GHz < f 6.375 GHz
6.375 GHz < f 12.75 GHz
12.75 GHz < f 25.5 GHz
25.5 GHz < f 40 GHz
1/4
1/32
1/16
1/8
1/4
1/2
1
2
4
8
16
32
19
Frequency modulation
Modulation source
External coupling
Operating modes
f 23.4375 MHz
f > 23.4375 MHz
FM mode normal
FM mode low noise
FM mode high deviation
Maximum deviation
Resolution
FM deviation error
FM distortion
Modulation frequency response
Synchronous AM with FM
Carrier frequency offset with FM DC
128 MHz
64 MHz
< 3 dB
< 0.2 %
< 0.2 % of set deviation
High Deviation
Normal
Low Noise
32 MHz
Maximum FM deviation
16 MHz
8 MHz
4 MHz
2 MHz
1 MHz
500 kHz
250 kHz
125 kHz
62.5 kHz
31.25 kHz
0.1
23.4375
46.875
93.75
187.5
375
750
1500
3000
Frequency / MHz
20
6375
12750
25500 40000
Phase modulation
Modulation source
External coupling
Operating modes
Maximum deviation
N 4 rad
N 10 rad
N 40 rad
< 0.02 % of set deviation,
min. N 20 rad
fmod = 1 kHz, deviation half of max. deviation
internal
< (2 % of setting + 0.003 rad)
external
< (3 % of setting + 0.003 rad)
fmod = 10 kHz, half of max. deviation
< 0.2 %
M modes low noise and high deviation
DC coupling: 0 Hz to 100 kHz,
< 3 dB
AC coupling: 10 Hz to 100 kHz
M mode normal
DC coupling: 0 Hz to 500 kHz,
< 3 dB
AC coupling: 10 Hz to 500 kHz
Resolution
M deviation error
M distortion
Modulation frequency response
1280 rad
640 rad
2 rad
High Deviation
Low Noise
Normal
320 rad
Maximum PM deviation
160 rad
128 rad
80 rad
64 rad
40 rad
32 rad
20 rad
16 rad
10 rad
8 rad
5 rad
4 rad
2.5 rad
2 rad
1.25 rad
1 rad
0.625 rad
0.5 rad
0.3125 rad
0.25 rad
0.125 rad
0.1
23.4375
46.875
93.75
187.5
375
750
1500
3000
6375
12750
25500 40000
Frequency / MHz
M deviation versus frequency and operating mode.
21
For instruments with electronic step attenuator (R&SSMB-B101/-B102/-B103/-B106 or R&SSMB-B112 frequency option), the level
during a sample and hold measurement is decreased by 30 dB:
The R&SSMB-K21 option is available for R&SSMB-B112/-B112L/-B120/-B120L/-B131/-B140/-B140L/-B140N
The R&SSMB-K22 option is available for R&SSMB-B101/-B102/-B103/-B106
Modulation source
On/off ratio
Rise/fall time
22
external, internal
> 80 dB
20 ns
30 ns
0 Hz to 25 MHz
< 25 dBc
< 30 dBc
BNC female
220 k or 600 (nom.)
1 V (nom.)
1 V (nom.)
10 V
BNC female
10 k or 50 (nom.)
0.5 V (nom.)
1.5 V (nom.)
5V
normal, inverse
23
Modulation sources
Internal modulation generator (LF)
Waveforms
Frequency range
Resolution of frequency setting
Frequency error
Frequency response
Frequency setting time
Distortion
Output voltage range
Resolution of output voltage setting
Output voltage setting error
Output impedance
LF frequency sweep
Operating mode
Trigger mode
Trigger source
Trigger slope
Sweep range
Sweep shape
Step spacing
Step size setting resolution
free run
full sweep
execute one step
external trigger only
linear
logarithmic
24
without load
user-programmable
automatic (free run)
externally triggered
positive or negative
1 to 2047
1 to 65535
10 ns to 5 ms
10 ns
25
L, R, R = L, R = L
L, R, R = L, R = L, R L
26
Remote control
Interfaces
Command set
Compatible command sets
remote control
Ethernet/LAN
USB
serial
These command sets can be selected in
order to emulate another instrument.
Ethernet/LAN addressing
USB protocol
27
Connectors
Front panel connectors
RF 50
RF output
R&SSMB-B101/-B102/-B103/B-B106
R&SSMB-B112/-B112L/-B120/-B120L
R&SSMB-B131/-B140/-B140L/-B140N
LF
MOD EXT
N female
test port adapter, PC 3.5 mm female
(interchangeable port connector system)
test port adapter, PC 2.92 mm female
(interchangeable port connector system)
BNC female
BNC female
L
R
S/P DIF
USB IN
USB
LAN
IEEE 488
10
Requires the R&SSMB-K23 option; only available for instruments with serial number > 102400.
28
BNC female
BNC female
BNC female
BNC female
BNC female
BNC female
BNC female
BNC female
BNC female
USB type B
USB type A
RJ-45
General data
Power supply
AC input voltage range
AC supply frequency
100 V to 240 V
100 V to 120 V
Test mark
EMC
Electromagnetic compatibility
Mechanical resistance
Vibration
Weight
Calibration interval
Recommended calibration interval
125 W (meas.)
140 W (meas.)
sinusoidal
Shock
Climatic resistance
Altitude
60 W (meas.)
80 W (meas.)
90 W (meas.)
105 W (meas.)
random
Environmental conditions
Temperature range
90 V to 264 V
45 Hz to 66 Hz
380 Hz to 440 Hz
1.4 A (100 V) to 0.6 A (240 V)
operating
storage
+40 C, 95 % relative humidity
operating,
max. ambient temperature = +45 C
storage
0 C to +55 C
in line with DIN EN 60068-2-1,
DIN EN 60068-2-2
40 C to +71 C
in line with DIN EN 60068-2-78
up to 4600 m (15000 ft)
up to 4600 m (15000 ft)
instruments with
R&SSMB-B101/-B102/-B103/-B106
option
instruments with
R&SSMB-B112/-B112L/-B120/-B120L/
-B131/-B140/-B140L/-B140N option
when fully equipped
instruments with
R&SSMB-B101/-B102/-B103/-B106
option
instruments with R&SSMB-B112 option
instruments with R&SSMB-B120/-B120L/
-B131/-B140/-B140/-B140N option
3 years
29
Ordering information
Designation
Type
Base unit
RF and Microwave Signal Generator 11
R&SSMB100A
Including power cable, quick start guide and CD-ROM (with operating and service manual)
Options
RF path/frequency option
9 kHz to 1.1 GHz
R&SSMB-B101
9 kHz to 2.2 GHz
R&SSMB-B102
9 kHz to 3.2 GHz
R&SSMB-B103
9 kHz to 6 GHz
R&SSMB-B106
100 kHz to 12.75 GHz, with electronic step attenuator
R&SSMB-B112
100 kHz to 12.75 GHz, without step attenuator
R&SSMB-B112L
100 kHz to 20 GHz, with mechanical step attenuator
R&SSMB-B120
100 kHz to 20 GHz, without step attenuator
R&SSMB-B120L
100 kHz to 31.8 GHz, with mechanical step attenuator
R&SSMB-B131
100 kHz to 40 GHz, with mechanical step attenuator
R&SSMB-B140
100 kHz to 40 GHz, without step attenuator
R&SSMB-B140L
100 kHz to 40 GHz, with mechanical step attenuator,
R&SSMB-B140N
minimum pulse width limited
OCXO Reference Oscillator 12
R&SSMB-B1
OCXO Reference Oscillator, High Performance 12
R&SSMB-B1H
Stereo/RDS Coder 13
R&SSMB-B5
Harmonic filter option
150 MHz to 20 GHz
R&SSMB-B25
11
12
13
14
Order No.
1406.6000.02
1407.2509.02
1407.2609.02
1407.2709.02
1407.2909.02
1407.2109.02
1407.2150.02
1407.2209.02
1407.2250.02
1407.2280.02
1407.2309.02
1407.2350.02
1407.2380.02
1407.3005.02
1407.3070.02
1407.3205.02
1407.1660.02
1407.1760.02
1407.1160.02
1407.1260.02
1407.1360.02
1407.3811.02
1407.3770.02
1407.3786.02
1407.3828.02
1109.4493.00
1171.7005.42
1138.2008.03
1137.7506.02
1146.8001.02
6124.2531.00
1021.0512.00
1021.0529.00
1021.0535.00
1021.0541.00
1088.1627.02
1036.4790.00
1036.4802.00
1036.4777.00
1036.4783.00
30
Designation
Documentation
Documentation of Calibration Values
DKD (ISO 17025) Calibration including ISO 9000 calibration
Warranty
Base unit
All other items
Options
Extended Warranty, one year
Extended Warranty, two years
Extended Warranty with Calibration Coverage, one year
Extended Warranty with Calibration Coverage, two years
Type
Order No.
R&SDCV-2
R&SSMB-DKD
0240.2193.18
1161.3607.02
3 years
1 year
R&SWE1
R&SWE2
R&SCW1
R&SCW2
Extended warranty with a term of one and two years (WE1 and WE2)
Repairs carried out during the contract term are free of charge 15. Necessary calibration and adjustments carried out during repairs are
also covered.
Extended warranty with calibration coverage (CW1 and CW2)
Enhance your extended warranty by adding calibration coverage at a package price. This package ensures that your
Rohde & Schwarz product is regularly calibrated, inspected and maintained during the term of the contract. It includes all repairs
calibration at the recommended intervals as well as any calibration carried out during repairs or option upgrades.
15
and
15
Excluding defects caused by incorrect operation or handling and force majeure. Wear-and-tear parts are not included.
31
About Rohde&Schwarz
The Rohde&Schwarz electronics group offers innovative
solutions in the following business fields: test and measurement, broadcast and media, secure communications,
cybersecurity, radiomonitoring and radiolocation. Founded
more than 80 years ago, the independent company which
is headquartered in Munich, Germany, has an extensive
sales and service network with locations in more than
70countries.
Sustainable product design
Environmental compatibility and eco-footprint
Energy efficiency and low emissions
Longevity and optimized total cost of ownership
Certified Quality Management
ISO9001
ISO14001
Rohde&Schwarz GmbH&Co. KG
www.rohde-schwarz.com
Rohde&Schwarz training
www.training.rohde-schwarz.com
Regional contact
Europe, Africa, Middle East | +4989412912345
customersupport@rohde-schwarz.com
North America | 1888TESTRSA (18888378772)
customer.support@rsa.rohde-schwarz.com
Latin America | +14109107988
customersupport.la@rohde-schwarz.com
Asia Pacific | +6565130488
customersupport.asia@rohde-schwarz.com
China | +868008108228 | +864006505896
customersupport.china@rohde-schwarz.com
5213839622
SMB100A_dat-sw_en_5213-8396-22_v0900_cover.indd 2
14.07.2016 19:10:02