Documente Academic
Documente Profesional
Documente Cultură
TH61MU3/H61M U3/H61MH/H61ML
UEFI BIOS M anual
UEFI BIOS Setup
Introduction
T he purpose of this manual is to describe the s ettings in the AMI UEFI BIOS Setup
program on this motherboard. The Setup program allows users to modify the basic
system configuration and save these settings to NVRAM.
UEFI BIOS determines what a computer can do without accessing programs from a
disk. T his system controls most of the input and output devices such as keyboard,
mouse, serial ports and disk drives. BIOS activates at the first stage of the booting
process, loading and executing the operating system. Some additional features, such
as virus and password protection or chipset fine-tuning options are also included in
UEFI BIOS.
T he rest of this manual will to guide you through the options and settings in UEFI
BIOS Setup.
ACPI Support
AMI ACPI UEFI BIOS support Version 1.0/2.0 of Advanced Con figuration and
Power interface speci fication (ACPI).
It provides ASL code for power
management and devi ce configu ration cap abilities as defined in the ACPI
specification, developed by Microsoft, Intel and Toshiba.
DRAM S upport
DDR3 SDRAM (Double Data Rate III Synchronous DRAM) is supported.
TH61MU3/H61M U3/H61MH/H61ML
UEFI BIOS M anual
Supported CP Us
T his AMI UEFI BIOS supports the Intel CPU.
Using Setup
When starting up the computer, press
<Del> during the Power-On Self-Test
(POST) to enter the UEFI BIOS setup
utility.
In the UEFI BIOS setup utility, you will
see General Help description at the top
right corner, and this is providing a brief
description of the selected item.
Navigation Keys for that particular menu
are at the bottom right corner, and you can
use these keys to select item and ch ange
the settings.
Notice
z
T he default UEFI BIOS settings apply for most conditions to ensure optimum
perform ance of the motherboard. If the system becomes unstable after changing
any settings, please load the default settings to ensure systems compatibility and
stability. Use Load Setup Default under the Exit Menu.
For better system performan ce, the UEFI BIOS firmware is being continuously
updated. T he UEFI BIOS information described in this manual is for your referen ce
only. T he actual UEFI BIOS information and settings on board may be slightly
different from this manual.
T he content of this manual is subject to be chang ed without notice. We will not be
responsible for any mistakes found in this users manual and any system damage that
may be caused by wrong-settings.
TH61MU3/H61M U3/H61MH/H61ML
UEFI BIOS M anual
1 Main Menu
Once you enter AMI UEFI BIOS Setup Utility, the Main Menu will appear on the
screen providing an overview of the basic system inform ation.
Main
Advanced
Chipset
Boot
BIOS Information
Compliency
Model Name
Marketing Name
Build Date
Total Memory
System Language
[English]
System Date
System Time
[Sat 01/01/2011]
[00:00:00]
Access Level
Administrator
Enter
+/F1
F3
F4
ESC
Select Screen
Select Item
Select
Change Opt.
General Help
Optimized Defaults
Save & Reset
Exit
BIOS Information
Shows system information including UEFI BIOS version, model name, marketing
name, built date, etc.
Total Memory
Shows system memory size, VGA shard memory will be excluded.
System Date
Set the system date. Note that the Day automatically changes when you set the
date.
System Time
Set the system internal clock.
Access Level
Shows the access level of current user.
TH61MU3/H61M U3/H61MH/H61ML
UEFI BIOS M anual
2 Advanced Menu
T he Advanced Menu allows you to configu re the settings of CPU, Super I/O, Power
Management, and other system devices.
Notice
z
Beware of that setting inappropriate values in items of this menu may cause
system to malfunction.
Main
>
>
>
>
>
>
>
>
Advanced
Chipset
Boot
Enter
+/F1
F3
F4
ESC
Select Screen
Select Item
Select
Change Opt.
General Help
Optimized Defaults
Save & Reset
Exit
V x.xx.xx
[Legacy ROM]
[Disabled]
[Disabled]
[Enabled]
[Auto]
[Auto]
Enter
+/F1
F3
F4
ESC
Select Screen
Select Item
Select
Change Opt.
General Help
Optimized Defaults
Save & Reset
Exit
TH61MU3/H61M U3/H61MH/H61ML
UEFI BIOS M anual
PCI ROM Priority
In case o f multiple option ROMs (Legacy and EFI Compatible), this item specifies
what PCI Option ROM to launch
Options: Legacy ROM (Default) / EFI Compatible ROM
PCI Latency Timer
T his item sets the value to be programmed into PCI Latency Timer Register.
Options: 32 PCI Bus Clocks (Default) / 64 PCI Bus Clocks / 96 PCI Bus Clocks /
128 PCI Bus Clocks / 160 PCI Bus Clocks / 192 PCI Bus Clocks / 224
PCI Bus Clocks / 248 PCI Bus Clocks
VGA Palette Snoop
T his item enables or disables VGA Palette Registers Snooping.
Options: Disabled (Default) / Enabled
PERR# Generation
T his item enables or disables PCI Device to generate PERR#.
Options: Disabled (Default) / Enabled
SERR# Generation
T his item enables or disables PCI Device to generate SERR#.
Options: Disabled (Default) / Enabled
Relaxed Ordering
T his item enables or disables PCI Express Device Relaxed Ordering.
Options: Disabled (Default) / Enabled
Extended Tag
If this item is enabled, the system allows Device to use 8-bit T ag field as a requester.
Options: Disabled (Default) / Enabled
TH61MU3/H61M U3/H61MH/H61ML
UEFI BIOS M anual
No Snoop
T his item enables or disables PCI Express Device No Snoop option.
Options: Enabled (Default) / Disabled
Maximum Payload
T his item sets Maximum Payload of PCI Express Device or allows System BIOS to
select the value.
Options: Auto (Default) / 128 Bytes / 256 Bytes / 512 Bytes / 1024 Bytes / 2048
Bytes / 4096 Bytes
Maximum Read Request
T his item sets Maximum Read Request Size of PCI Express Device or allows
System BIOS to select the value.
Options: Auto (Default) / 128 Bytes / 256 Bytes / 512 Bytes / 1024 Bytes / 2048
Bytes / 4096 Bytes
ASPM Support
T his item sets the ASPM Level: Force LO Force all links to LO State; Auto
BIOS auto configures; Disabled Disables ASPM.
Options: Disabled (Default) / Auto / Force LO
Extended Synch
If this item is enabled, the system allows generation o f Extend ed Synchronization
patterns.
Options: Disabled (Default) / Enabled
TH61MU3/H61M U3/H61MH/H61ML
UEFI BIOS M anual
ACPI Settings/WakeUp Event control
BIOS SETUP UTILITY
Advanced
ACPI Settings/Wakeup Event Control
ACPI Sleep State
EuP Control
PME Wake up from S5
Wake system with Fixed Time
Wake up date
Wake up hour
Wake up minute
Wake up second
[Disabled]
[Disabled]
[Wake Key]
[Disabled]
[Disabled]
Enter
+/F1
F3
F4
ESC
Select Screen
Select Item
Select
Change Opt.
General Help
Optimized Defaults
Save & Reset
Exit
TH61MU3/H61M U3/H61MH/H61ML
UEFI BIOS M anual
Wake up date
You can choose which date the system will boot up.
Wake up hour / Wake up minute / Wake up second
You can choose the system boot up time, input hour, minute and second to specify.
Ring-In Wake up from S5
T his item enables the system to wake from S5 using Ring-In event.
Options: Disabled (Default) / Enabled
PS2 Keyboard PowerOn
T his item allows you to control the keyboard power on function.
Options: Disabled (Default) / Any Key / Stroke Key / Specific K ey
Stroke Keys Selected
T his item will show only when Keyboard PowerOn is set Stroke Key.
Options: Wake Key (Default) / Power Key / Ctrl+F1 / Ctrl+F2 / Ctrl+F3 /
Ctrl +F4 / Ctrl+F5 / Ctrl+F6
Specific Key Enter
T his item will show only when Keyboard PowerOn is set Specific Key. Press
Enter to set Specific key.
PS2 Mouse PowerOn
T his item allows you to control the mouse power on function.
Options: Disabled (Default) / Enabled
USB Dev ice Wakeup from S3/S4
T his item allows you to enable or disabled the USB resume from S3/S4 function.
Options: Disabled (Default) / Enabled
TH61MU3/H61M U3/H61MH/H61ML
UEFI BIOS M anual
CPU Configuration
BIOS SETUP UTILITY
Advanced
CPU Configuration
EMT64
Processor Speed
Processor Stepping
Microcode Revision
Processor Cores
Intel HT Technology
Hyper-threading
[Enabled]
Active Processor Cores
[All]
Limit CPUID Maximum
[Disabled]
Execute-Disable Bit
[Enabled]
Hardware Prefetcher
[Enabled]
Adjacent Cache Line Prefetch
[Enabled]
Intel Virtualization Technology[Disabled]
Power Technology
[Energy Efficient]
Local x2APIC
[Disabled]
Enter
+/F1
F3
F4
ESC
Select Screen
Select Item
Select
Change Opt.
General Help
Optimized Defaults
Save & Reset
Exit
Hyper-threading
Hyper T hreading T echnology can improve p erfo rmance by splitting instructions into
multiple streams. T his item is enabled fo r Windows XP and Linux (OS optimized for
Hyper-T hreading T echnology) and disabled for other OS (OS not optimized for
T hreading T echnology). When this item is disabled, only one thread per enabled co re
is enabled.
Options: Enabled (Default) / Disabled
Active Processor Cores
T his item sets number of cores to enable in each processor pack age.
Options: All (Default) / 1 / 2 / 3
Limit CPUID Maximum
When the computer is booted up, the operating system executes the CPUID
instruction to identify the processor and its capabilities. Befo re it can do so, it must
first query the processor to find out the highest input value CPUID recognizes. T his
determines the kind of basic information CPUID can provide the operating system.
Options: Disabled (Default) / Enabled
TH61MU3/H61M U3/H61MH/H61ML
UEFI BIOS M anual
Execute-Disable Bit
XD can prevent certain classes of malicious bu ffer ov erflow attacks wh en combined
with a supporting OS (Windows Server 2003 SP1, Windows XP SP2, SuSE Linux
9.2, RedHat Enterprise 3 Update 3.).
Options: Enabled (Default) / Disabled
Hardware Prefetcher
T he processor has a hardw are prefetch er that automatically analy zes its requirements
and prefetches dat a and instructions from the memory into the Level 2 cache that are
likely to be required in the near future. T his reduces the latency associated with
memory reads.
Options: Enabled (Default) / Disabled
Adj acent Cache Line Prefetch
T he processor has a h ardw are adjacent cache line prefet ch mech anism that
automatically fetches an extra 64-byte cache line whenev er the processo r requests for
a 64-byte cach e line. T his reduces cach e latency by making the next cache line
immediately available if the processor requires it as well.
Options: Enabled (Default) / Disabled
Intel Virtualization Tech
Virtualization T echnology can virtually separate your system resou rce into several
parts, thus enhance the performance when running virtual machines or multi
interface systems.
Options: Disabled (Default) / Enabled
Power Technology
T his item enables the power management features.
Options: Energy E ffici ent (Default) / Disabled / Custom
CPU C3 Report
T his item enables/disables CPU C3 (ACPI C2) report to OS.
Options: Disabled (Default) / ACPI C-2 / ACPI C-3
10
TH61MU3/H61M U3/H61MH/H61ML
UEFI BIOS M anual
CPU C6 Report
T his item enables/disables CPU C6 (ACPI C3) report to OS.
Options: Enabled (Default) / Disabled
Package C State Limit
T his item sets Package C State Limit.
Options: No Limit (Default) / C0 / C1 / C6 / C7
Local x2APIC
T his item enables Local x2APIC. Some OSes do not support this featu re.
Options: Disabled (Default) / Enabled
SATA Configuration
BIOS SETUP UTILITY
Advanced
(1) IDE Mode
SATA Configuration
SATA Mode
Serial-ATA Controller 0
Serial-ATA Controller 1
[IDE Mode]
[Compatible]
[Enhanced]
SATA Port1:
SATA Port2:
SATA Port5:
SATA Port6:
Enter
+/F1
F3
F4
ESC
Select Screen
Select Item
Select
Change Opt.
General Help
Optimized Defaults
Save & Reset
Exit
SATA Mode
T his item sets SAT A Mode.
Options: IDE Mode (Default) / Disabled
Serial-ATA Con troller 0
T his item enables/disables Serial AT A Controller 0.
Options: Compatible (Default) / Disabled / Enhanced
11
TH61MU3/H61M U3/H61MH/H61ML
UEFI BIOS M anual
Serial-ATA Con troller 1
T his item enables/disables Serial AT A Controller 1.
Options: Enhanced (Default) / Disabled
USB Configuration
BIOS SETUP UTILITY
Advanced
USB Configuration
USB Devices:
Legacy USB Support
EHCI Hand-off
Port 60/64 Emulation
[Enabled]
[Disabled]
[Enabled]
Enter
+/F1
F3
F4
ESC
Select Screen
Select Item
Select
Change Opt.
General Help
Optimized Defaults
Save & Reset
Exit
12
TH61MU3/H61M U3/H61MH/H61ML
UEFI BIOS M anual
SMART FAN Control
BIOS SETUP UTILITY
Advanced
SMART FAN Control
CPU Smart FAN
> CPU FAN Calibrate
Control Mode
FAN Ctrl OFF(oC)
FAN Ctrl ON( oC)
FAN Ctrl Start value
FAN Ctrl Sensitive
[Disabled]
[Manual]
Enter
+/F1
F3
F4
ESC
Select Screen
Select Item
Select
Change Opt.
General Help
Optimized Defaults
Save & Reset
Exit
13
TH61MU3/H61M U3/H61MH/H61ML
UEFI BIOS M anual
Fan Ctrl Start Value
T his item sets CPU FAN Start Speed Value.
Options: 50 (Default)
Fan Ctrl Sensitive
T he bigger the numeral is, the higher the FAN speed is.
Options: 30 (Default)
Super IO Configuration
BIOS SETUP UTILITY
Advanced
Specify what state to go to
when power is re-applied
after a power failure.
Super IO Configuration
Super IO Chip
Restore AC Power Loss
[Power Off]
Enter
+/F1
F3
F4
ESC
Select Screen
Select Item
Select
Change Opt.
General Help
Optimized Defaults
Save & Reset
Exit
14
TH61MU3/H61M U3/H61MH/H61ML
UEFI BIOS M anual
Serial Port 1 Configuration
BIOS SETUP UTILITY
Advanced
Enable or Disable Serial Port
(COM)
[Enabled]
Change Settings
[Auto]
Enter
+/F1
F3
F4
ESC
Select Screen
Select Item
Select
Change Opt.
General Help
Optimized Defaults
Save & Reset
Exit
Serial Port
T his item enables or disables Serial Port (COM).
Options: Enabled (Default) / Disabled
Change Settings
T his item allows you to select an optimal setting for Super IO device.
Options: Auto (Default) / IO=3F8h; IRQ=4 / IO=3F8h; IRQ=3, 4, 5, 6, 7, 9, 10, 11,
12 / IO=2F8h; IRQ=3, 4, 5, 6, 7, 9, 10, 11, 12 / IO=3E8h; IRQ=3, 4, 5, 6,
7, 9, 10, 11, 12 / IO=2E8h; IRQ=3, 4, 5, 6, 7, 9, 10, 11, 12
Parallel Port Configuration
BIOS SETUP UTILITY
Advanced
Enable or Disable Parallel
Port (LPT/LPTE)
[Enabled]
Change Settings
Device Mode
[Auto]
[Standard Parall...]
Enter
+/F1
F3
F4
ESC
Select Screen
Select Item
Select
Change Opt.
General Help
Optimized Defaults
Save & Reset
Exit
15
TH61MU3/H61M U3/H61MH/H61ML
UEFI BIOS M anual
Parallel Port
T his item enables or disables Parallel Port (LPT /LPT E).
Options: Enabled (Default) / Disabled
Change Settings
T his item allows you to select an optimal setting for Super IO device.
Options: Auto (Default) / IO=378h; IRQ=5 / IO=378h; IRQ=5, 6, 7, 9, 10, 11, 12 /
IO=278h; IRQ=5, 6, 7, 9, 10, 11, 12 / IO=3BCh; IRQ=5, 6, 7, 9, 10, 11,
12
Device Mode
T his item allows you to determine how the parallel port should function.
Options: Standard Parallel Port Mode (Default) (Using Parallel port as Standard
Printer Port) /
EPP Mode (Using Parallel Port as Enhanced Parallel Port) /
ECP Mode (Using Parallel port as Extended Capabilities Port) /
ECP Mode & EPP Mode (Using Parallel port as ECP & EPP mode)
CIR Controller Configuration
BIOS SETUP UTILITY
Advanced
Enable or Disable CIR
Controller
[Disabled]
Enter
+/F1
F3
F4
ESC
Select Screen
Select Item
Select
Change Opt.
General Help
Optimized Defaults
Save & Reset
Exit
CIR Controller
T his item enables or disables CIR Controller.
Options: Disabled (Default) / Enabled
16
TH61MU3/H61M U3/H61MH/H61ML
UEFI BIOS M anual
Change Settings
T his item selects an optimal setting for Super IO device.
Options: Auto (Default) / IO=3E0h; IRQ=10 / IO=3E0h; IRQ=3, 4, 5, 6, 7, 9, 10,
11, 12 / IO=2E0h; IRQ=3, 4, 5, 6, 7, 9, 10, 11, 12 / IO=298h; IRQ=3, 4, 5,
6, 7, 9, 10, 11, 12
H/W Monitor
BIOS SETUP UTILITY
Advanced
ShutDown Temperature
PC Health Status
ShutDown Temperature
CPU temperature
System temperature
CPU Fan Speed
System Fan1 Speed
CPU Vcore
DRAM Voltage
+12V
+ 5V
Vcc SA
IGD Voltage
Vcc IO
[Disabled]
:
:
:
:
:
:
:
:
:
:
:
Enter
+/F1
F3
F4
ESC
Select Screen
Select Item
Select
Change Opt.
General Help
Optimized Defaults
Save & Reset
Exit
Shutdow n Temperature
T his item allows you to set up the CPU shutdown T emperature.
Options: Disabled (Default) / 70 /158 / 75/167 / 80/176 / 85/185
/ 90/194
17
TH61MU3/H61M U3/H61MH/H61ML
UEFI BIOS M anual
3 Chipset Menu
T his section describes con figuring the PCI bus system. PCI, or Personal Computer
Interconn ect, is a system which allows I/O devices to operate at speeds nearing the
speed o f the CPU itself uses when communicating with its own special components.
Notice
z
Beware o f that setting inappropriate values in items of this menu may cause
system to malfunction.
Main
Advanced
Chipset
Boot
Enter
+/F1
F3
F4
ESC
Select Screen
Select Item
Select
Change Opt.
General Help
Optimized Defaults
Save & Reset
Exit
North Bridge
BIOS SETUP UTILITY
Chipset
VT-d Enable/Disable
Memory Information
Total Memory
DDR3_A1
DDR3_B1
VT-d
[Disabled]
[PEG/IGD]
[64M]
[Enabled]
[DVMT Mode]
[256MB]
[Disabled]
[Auto]
[Disabled]
[Enabled]
Enter
+/F1
F3
F4
ESC
Select Screen
Select Item
Select
Change Opt.
General Help
Optimized Defaults
Save & Reset
Exit
18
TH61MU3/H61M U3/H61MH/H61ML
UEFI BIOS M anual
VT-d
T his item enables/disables VT -d function.
Options: Disabled (Default) / Enabled
Initiate Graphic Adapter
T his item allows you to select which graphics controller to use as the primary boot
device.
Options: PEG/PCI (Default) / IGD / PCI/IGD / PCI/PEG / PEG/IGD
IGD Memory
T his item sets IGD Share Memory Size.
Options: 64M (Default) / Disabled / 32M / 128M / 160M / 192M / 224M / 256M /
288M / 320M / 352M / 384M / 416M / 448M / 480M / 512M
Render Standby
T his item enables/disables Render Standby by Internal Graphics Device.
Options: Enabled (Default) / Disabled
DVMT Mode Select
T his item selects DVMT Mode used by Internal Graphics Device.
Options: DVMT Mode (Default) / Fixed Mode
DVMT/FIXED Memory Size
DVMT stands for Dynamic Video Memory T echnology. T his is an enhancement
of the unified memory architecture (UMA) concept. DVMT will set the optimum
amount of memory to be allocated for a balance between graphics and system
perform ance. DVMT dynamically respond to system requirements and applications
demands, by allocating the proper amount of display, texturing and buffer memory
after the operating system has booted.
Options: 256MB (Default) / 128MB / Maximum
19
TH61MU3/H61M U3/H61MH/H61ML
UEFI BIOS M anual
IGD Multi-Monitor
T his item enables/disables IGD Multi-Monitor by Internal Graphics Device.
Options: Disabled (Default) / Enabled
PCI Express Port
T his item allows user to control PCI Express x16 Port.
Options: Auto (Default) / Disabled / Enabled
PEG Force Gen1
Some non-graphics PCI-E devices may not follow PCI-E Speci fication and may
incorrectly report their Gen cap ability or link width.
Options: Disabled (Default) / Enabled
Detect Non-Compliance Dev ice
Detect Non-Compliance PCI Express Device in PEG.
Options: Enabled (Default) / Disabled
ME Version
Audio Configuration
Azalia HD Audio
Azalia internal HDMI codec
[Enabled]
[Enabled]
Enter
+/F1
F3
F4
ESC
Select Screen
Select Item
Select
Change Opt.
General Help
Optimized Defaults
Save & Reset
Exit
Azalia HD Audio
T his item enables/disables Azalia HD Audio.
Options: Enabled (Default) / Disabled
20
TH61MU3/H61M U3/H61MH/H61ML
UEFI BIOS M anual
Azalia internal HDMI codec
T his item enables/disables internal HDMI codec for Azalia.
Options: Enabled (Default) / Disabled
High Precision Timer
T his item enables/disables the High Precision Event T imer.
Options: Enabled (Default) / Disabled
PCI Express Ports Configuration
BIOS SETUP UTILITY
Chipset
Enable or Disable Boot Option
for Legacy Network Devices.
[Disabled]
[Enabled]
[Auto]
[Auto]
[Auto]
[Auto]
[Enabled]
Enter
+/F1
F3
F4
ESC
Select Screen
Select Item
Select
Change Opt.
General Help
Optimized Defaults
Save & Reset
Exit
21
TH61MU3/H61M U3/H61MH/H61ML
UEFI BIOS M anual
Onboard USB3.0 (Only for TH61MU3/H61MU3)
T his item enables/disables Onboard USB3.0.
Options: Auto (Default) / Disabled / Enabled
Onboard PCI Bridge
T his item enables/disables Onboard PCI Bridge.
Options: Auto (Default) / Disabled / Enabled
PCI Express Port x1
T his item enables/disables PCI Express Port x1.
Options: Auto (Default) / Disabled / Enabled
PCIe Sub Decode
T his item enables/disables PCIe Sub Decode Port. (T his option is available when
Subtractive Decod e Agent is enabled (PCHT rap9[14]) = 1b)
Options: Enabled (Default) / Disabled
USB Configuration
BIOS SETUP UTILITY
Chipset
Enabled/Disabled All USB
Devices
USB Configuration
All USB Devices
[Enabled]
EHCI Controller 1
EHCI Controller 2
[Enabled]
[Enabled]
Enter
+/F1
F3
F4
ESC
Select Screen
Select Item
Select
Change Opt.
General Help
Optimized Defaults
Save & Reset
Exit
22
TH61MU3/H61M U3/H61MH/H61ML
UEFI BIOS M anual
All USB Devices
T his item enables/disables All USB Devices.
Options: Enabled (Default) / Disabled
EHCI Controller 1
T his item enables/disables USB 2.0 (EHCI) Support.
Options: Enabled (Default) / Disabled
EHCI Controller 2
T his item enables/disables USB 2.0 (EHCI) Support.
Options: Enabled (Default) / Disabled
23
TH61MU3/H61M U3/H61MH/H61ML
UEFI BIOS M anual
4 Boot Menu
T his menu allows you to setup the system boot options.
Main
Advanced
Chipset
Boot
Boot Configuration
Setup Prompt Timeout
Bootup NumLock State
1
[On]
[Enabled]
[Upon Request]
[Force BIOS]
[Disabled]
[Enabled]
[Disabled]
Enter
+/F1
F3
F4
ESC
Select Screen
Select Item
Select
Change Opt.
General Help
Optimized Defaults
Save & Reset
Exit
GateA20 Active
Upon Request FA20 can be disabled using BIOS services. Always do not allow
disabling GA20; this option is useful when any RT code is executed above 1MB
Options: Upon Request (Default) / Always
24
TH61MU3/H61M U3/H61MH/H61ML
UEFI BIOS M anual
Option ROM Messages
T his item sets the display mode for Option ROM.
Options: Force BIOS (Default) / Keep Current
Interrupt 19 Capture
Interrupt 19 is the software interrupt that handles the boot disk function.
to Enabled, this item allows the option ROMs to trap interrupt 19.
Options: Disabled (Default) / Enabled
When set
UEFI Boot
T his option enables/disables boot from the UEFI Devices.
Options: Disabled (Default) / Enabled
25
TH61MU3/H61M U3/H61MH/H61ML
UEFI BIOS M anual
5 Security Menu
Main
Advanced
Chipset
Boot
Password Description
If ONLY the Administrators password is set,
then this only limits access to Setup and is
only asked for when entering Setup.
If ONLY the Users password is set, then this
is a power on password and must be entered to
boot or enter Setup. In Setup the User will
have Administrator rights.
The password must be 3 to 20 characters long.
Administrator Password
User Password
Enter
+/F1
F3
F4
ESC
Select Screen
Select Item
Select
Change Opt.
General Help
Optimized Defaults
Save & Reset
Exit
Administrator Password
T his item sets Administrator Password.
User Password
T his item sets User Password.
26
TH61MU3/H61M U3/H61MH/H61ML
UEFI BIOS M anual
6 Performance Menu
T his submenu allows you to change voltage and clock of various devices.
(Howev er, we suggest you use the default setting. Changing the voltage and clock
improperly may damage the device.)
Notice
z
Beware of that setting inappropriate values in items of this menu may cause
system to malfunction.
Main
Advanced
Chipset
Boot
[Disabled]
34
10000
105
95
[Enabled]
118
[Enabled]
[Enabled]
[Enabled]
30
Enter
+/F1
F3
F4
ESC
Select Screen
Select Item
Select
Change Opt.
General Help
Optimized Defaults
Save & Reset
Exit
Start Page
You can set the entrance pag e when you enter UEFI BIOS Setup.
Options: Page Main (Default) / Page Advanced / Page Chipset / Page Boot
/ Page Security / Page O.N.E / Page Save & Exit
Fixed CP U Ratio
T his item enables/disables Fixed CPU Ratio all the time.
Options: Disabled (Default) / Enabled
27
TH61MU3/H61M U3/H61MH/H61ML
UEFI BIOS M anual
CPU Ratio
T his item allows you to set the CPU ratio. T his item is adjustable only when Fixed
CPU Ratio is set to Enabled.
Options: 34 (Default) / 10 ~ 50
Turbo M ode
T his item enables/disables T urbo Mode.
Options: Enabled (Default) / Disabled
28
TH61MU3/H61M U3/H61MH/H61ML
UEFI BIOS M anual
CPU C1 E
C1E is Enhanced Halt State function, this function helps to save power and
decrease heat by lowering CPU frequen cy while the processor is not working.
Options: Enabled (Default) / Disabled
29
TH61MU3/H61M U3/H61MH/H61ML
UEFI BIOS M anual
RAS# Active Time (tRAS)
T his item allows you to select Row Active T ime of DDR3.
Options: 24 (Default) / 9 ~ 63
30
TH61MU3/H61M U3/H61MH/H61ML
UEFI BIOS M anual
CPU VCore Mode
T his item sets the mode of CPU over voltage.
Options: SPEC Voltage (Default) / Auto / Offset Mode / Fixed Mode
31
TH61MU3/H61M U3/H61MH/H61ML
UEFI BIOS M anual
CPU VCore LoadLine
T his item sets VCore LoadLine.
Options: Enabled (Default) / Disabled
DRAM Voltage
T his item sets DRAM Voltage.
CPU PLL
T his item sets CPU PLL power supply.
PCH Voltage
T his item sets PCH Voltage.
Enter
+/F1
F3
F4
ESC
Select Screen
Select Item
Select
Change Opt.
General Help
Optimized Defaults
Save & Reset
Exit
32
TH61MU3/H61M U3/H61MH/H61ML
UEFI BIOS M anual
7 Exit Menu
T his menu allows you to load the optimal default settings, and save or discard the
changes to the BIOS items.
Main
Advanced
Chipset
Boot
Enter
+/F1
F3
F4
ESC
Select Screen
Select Item
Select
Change Opt.
General Help
Optimized Defaults
Save & Reset
Exit
Restore Defaults
T his selection allows you to reload the BIOS when problem occurs during system
booting sequence. T hese con figurations are facto ry settings optimized fo r this
system.
33