Documente Academic
Documente Profesional
Documente Cultură
General information
24 [0.945"]
Shank:
o 4.5
[0.177"]
M8
o 4.5
[0.177"]
Material specifications
o 12
[0.472"]
o 12
[0.472"]
M10/
W10
1.4401
21.3
[0.839"]
17-12-2, 1.4404)
4.5
12
20 [0.787"]
31.3 [1.232"]
Plastic
[0.472"]
M6/
W6
Available on request
N 08926 (1.4529) 1
14
4
[0.551"]
31.3 [1.232"]
S31803 (1.4462)
5
[0.197"]
5
DX 351-BT / BTG
[0.197"]
See X-BT fastener program in the next pages and
1.58
Tools and equipment chapter for more details.
[0.062"]
Approvals
Applications
Examples
07 / 2015
8 mm
4.7 - 5.5 mm
187
X-BT
Base plates
Installation rails
Load data
Recommended loads steel
Steel grade:
Europe, USA
S235,
A36
S355, Grade 50
and stronger steel
Tension,
Nrec [kN/lb]
1.8 / 405
2.3 / 517
Shear,
Vrec [kN/lb]
2.6 / 584
3.4 / 764
8.2 / 6
8.2 / 6
Trec [Nm/lbft]
8 / 5.9
8 / 5.9
Torque,
N
M
Example:
Nrec [kN/lb]
0.5 / 115
Shear,
Vrec [kN/lb]
0.75 / 170
Z2
Z1
FV
Z3
FN
8.2 / 6
Requirements
Cast iron
Strength class
Chemical analysis and
amount of carbon
Mictrostructure
Material thickness
188
07 / 2015
X-BT
S235
S355
Tension
NRd [kN]
2.9
3.7
Shear
VRd [kN]
4.2
5.4
Moment
MRd [Nm]
18.4
18.4
NRD [kN]
Shear
VRD [kN]
Moment
MRD [Nm]
0.8
1.2
13.1
Recommended interaction formula for combined loading - steel and cast iron base material
Combined loading situation
Interaction formula
V
N
V
N
+
1.2 with
1.0 and
1.0
Vrec Nrec
Vrec
Nrec
V
M
V
M
+
1.2 with
1.0 and
1.0
Vrec Mrec
Vrec
Mrec
N
M
+
1.0
Nrec Mrec
V
N
M
+
+
1.0
Vrec Nrec Mrec
F
Cyclic loading:
Anchorage of X-BT-R threaded stud in steel base material is not affected by cyclic loading.
Fatigue strength is governed by fracture of the shank. Inquire at Hilti for test data if high cycle loading has to
be considered in the design.
07 / 2015
189
X-BT
Application requirements
Thickness of base material
> 8mm [5/16"]
tI
tWASHER
Lg
tNUT
>6
> 15
[0.236"] [0.591"]
> 15
[0.591"]
Spacing: 15 mm
>6
> 15 > 6 > 15
[0.236"
]
[0.236"] [0.591"
]
[0.591"
]
>6
[0.236"]
Corrosion information
The corrosion resistance of Hilti CR500 and S31803 stainless steel material is equivalent to
AISI 316 (A4) steel grade.
Studs made of N 08926 (HCR) material with higher corrosion resistance, e.g. for use in road
tunnels or swimming pools, are available on special order.
190
07 / 2015
X-BT
Application limit
tII 8 mm [5/16] No through penetration
No limits with regards to steel strength
Designation
Item no.
Designation
377074
DX 351-BTG
377078
DX 351-BT
377076
DX 351-BT
377075
DX 351-BT
432266
DX 351-BT
432267
DX 351-BT
07 / 2015
191
X-BT
X-BT M8
hNVS = 15.716.8 mm
X-BT M10 / X-BT W10 and
X-BT M6 / X-BT W6
hNVS = 25.726.8 mm
Installation
X-BT with washer
Fastened material hole
13 mm
X-BT M6 / X-BT W6
Fastened material with
pre-drilled hole diameter
< 7 mm
192
07 / 2015
X-BT
Tightening torque:
Trec 8 Nm (5.9 ft-lb)!
Trec
Hilti
screwdriver:
SF 121-A
SF 150-A
SF 180-A
SF 144-A
SF 22A
Torque
setting:
11
9
8
9
9
193
194