Documente Academic
Documente Profesional
Documente Cultură
( Reaffirmed 1998 )
Indian Standard
SPECIFICATIONFOR
FABRICATED PVC FITTINGS FOR
POTABLE WATER SUPPLIES
PART 2
SPECIFIC
f
REQUIREMENTS
FOR SOCKETS
First Revision )
621.643.413
UDC
[678.743.22]:696.117
@ Copyright 1989
-BUREAU
MANAK
Gr 1
OF
BHAVAN,
INDIAN
STANDARDS
9 BAHADUR
SHAH
NEW DELHI 110002
ZAIAR
MARG
Apt-ii 1989
Indian Standard
SPECIFICATIONFOR
FABRICATED PVC FITTINGS FOR
POTAB~LEWATER SUPPLIES
PART 2
SPECIFIC
REQUIREMENTS
FOR SOCKETS
First Revision )
0. FOREWORD
0.1 This Indian
Standard
( Part 2 ) ( First
Revision ) was adopted by the Bureau of Indian
Standards on 20 June 1988, after the draft finalized by the Sanitary Appliances and Water Fittings
Sectional Committee had been approved by the
Civil Engineering Division Council.
0.2 The fabricated PVC fittings are to be used
for jointing to the PVC pipes covered by IS :
4985-1988*.
0.3 The requirements of fabricated PVC fittings
are covered in thirteen parts. This part ( Part 2 )
deals with specific requirements for sockets.
Other parts are as follows:
Part 1 General requirements
for
straight
Part 3 Specific requirements
reducers
Part 4 Specific requirements
Part 5 Specific
Part 6 Specific
requirements
for caps
for
equal
Part 7 Specific
requirements
for
tail
threaded
adaptors
Part 8 Specific
requirements
for 45 bends
for 30 bends
for lip
bends
0.3.1 Part 1 of this series deals with the general .requirements applicable to all fabricated PVC
fittings, and specific requirements
of different
types of fittings ari: covered in separate parts of
This part ( Part 2 ) deals with the
the standatd.
specific requirements for sockets.
This part was
first published in 1982. The present revision has
been taken up to extend the size of fittingsto
630 mm in line with the sizes of pipes specified
in IS : 49851988.
0.4 For the purpose of deciding whether a particular requirement
of this standard is complied
with, the final value, observed or calculated,
expressing the result of a test or analysis, shall
be rounded off in accordance with IS : 2-196Ot.
The number of significant places retained in the
tees
requirements
for fianged
pieces with metallic flanges
for 90 bends
of
for 60 bends
1. SCOPE
( Part
1.1 This
standard
( Part 2 ) lays down the
requirements for manufacture, dimensions and
marking for fabricated PVC sockets for potable
water supplies.
1 )-1988*.
2.2 Manufacture
2.2.1 A typical
in Fig. 1.
illustration
of-socket is given
2. REQUIREMENTS
2.1 General - The general requirements
for
materials, sizes, methods of test, sampling and
1
*Specification
fabricated PVC fittings for potable
water
supplies.. for
Part 1 General requirements (firsr
revision ).
DIMENSIONS
OF SOCKET
2.2.2
D=
L=
t?
500
560
630
or
(3)
1.2
;:;
1.8
::
(4)
(5 )
(6)
1.9
2.7
2.3
2.8
;:;
4.5
6.3
55
2.9
4.4
70_
33:; 54;
l.0
z:
65
7.3
;:;
9.7
10.8
13.7
12.2
100
112
125
13.9
15.6
17.7
22.4
19.8
2:
75
75
103
116
130
15.3
172
192
248
27.8
31.3
tz
55
55
Class of Fitting
3. MARKING
3.1 Each socket fitting shall be marked with the,
following information:
::
45
2:;
2.9
$3
;:6
COlOU?-
Red
Blue
Green
Yellow
identification
mark,
b)
(2)
20
20
35
:!:
name
(1)
63
75
90
110
125
140
*,,-.
IO
200
225
250
280
315
355
a) Manufacturers
B
Min
180
Dimensions
shall
comply
with Fig,
1.
1 SOCKCT
SIZE
dimensions in millimetres.
Amend No.
Text Affected
b\
BUREAU
OF INDIAN
STANDARDS
Headquarters:
Manak Bhavan, 9 Bahadur Shah Zafar Marg, New Delhi 110002
Telephones : 331 01 31, 331 13 75
Telegrams
( Common
: Manaksanstha
to all Offices )
Regional Offices :
Central
: Manak Bhavan,
NEW DELHI
Eastern
Telephone
9 Bahadur
110002
CALCUTTA
700054
Northern
Southern
: C. I. T. Campus, IVCross
Western
: Manakalaya,
Branches
I 331 01 31
331 13 75
35-C, CHANDIGARH
Road, MADRAS
160036
600113
I 37 84 99,
37 86 26,
37 85 61,
37 85 62
53 38 43,
53 23 84
53 16 40,
I 41 23
24 42,
15,
19,
41 29
25 16