Documente Academic
Documente Profesional
Documente Cultură
Worldwide
Home : shortcuts : Revit Sites G
Keyboard Shortcuts
You have been detected as bein
from India. Where applicable, y
Jump to a section
Annotate | Analyze | Architecture | Collaborate | Context Menu | Contextual Tabs | Create | Manage | Modify |
Navigation Bar | Snaps | Structure | System | View | View Control Bar
Annotate
Analyze
ADJUST ANALYTICAL MODEL / Adjusts the analytical model of the structural member in
AA
relation to those of the elements to which it joins.
CHECK DUCT SYSTEMS / Examines the mechanical systems in a project to verify that each
DC
system is assigned to a userdefined system, and properly connected.
CHECK CIRCUITS / Verifies all circuits for proper connections to panels and valid system
EC
assignments.
HEATING AND COOLING LOADS / Prepares a heating and cooling load analysis report based on
LO
an existing building model.
About Cookies on this site:
PC Our site uses cookies and similar technologies. Manage your cookie preferences here. Further use of this site will be considered consent.
CHECK PIPE SYSTEMS / Examines the piping systems in a project to verify that each system is
assigned to a user-defined system, and properly connected.
RA RESET ANALYTICAL MODEL / Restores the analytical model alignment methods to auto-detect.
Architecture
Collaborate
EDITING REQUESTS / Displays a list of users requests to borrow elements in worksets, as well
ER
as pending requests.
Context Menu
R3 DEFINE A NEW CENTER OF ROTATION / Relocates center of rotation when rotating elements.
SELECT ALL INSTANCES: IN ENTIRE PROJECT / Selects all of the elements that are similar to the
SA
selected element in the current view, or throughout the project.
Contextual Tabs
ADJUST ANALYTICAL MODEL / Adjusts the analytical model of the structural member in
AA
relation to those of the elements to which it joins.
RH TOGGLE REVEAL HIDDEN ELEMENTS MODE / Toggles the Reveal Hidden Elements Mode.
Create
Our site uses cookies and similar technologies. Manage your cookie preferences here. Further use of this site will be considered consent.
MEP SETTINGS:ELECTRICAL SETTINGS / Accesses dialog box to specify wiring parameters,
ES voltages definitions, distribution systems, cable tray and conduit settings, and load calculation
and circuit numbering settings.
Modify
CS CREATE SIMILAR / Creates an element of the same type as the selected element.
MIRROR - DRAW AXIS / Reverses the position of a selected model element, using a user-
DM
generated line as the mirror axis.
LW LINEWORK / Overrides the line style of selected line in the active view only.
MATCH TYPE PROPERTIES / Opens the Match Type tool to convert one or more elements to
MA
match the type assigned to another element.
MIRROR - PICK AXIS / Reverses the position of a selected model element, using a selected line
MM
as the mirror axis.
OFFSET / Moves a selected model line, detail line, wall, or beam a specified distance
OF
perpendicular to its length.
SF SPLIT FACE / Divides the face of an element into regions for application of different materials.
About Cookies on this site:
SL SPLITtechnologies.
Our site uses cookies and similar ELEMENT / Manage
Cuts an your
element (such
cookie as a wallhere.
preferences or line) at a selected
Further use of thispoint.
site will be considered consent.
TR TRIM/EXTEND TO CORNER / Trims or extend one or more elements to form a corner.
UNPIN / Unpins an element that is locked in position or an element that is driven by its host
UP
system.
Navigation Bar
3O OBJECT MODE / Navigates and reorients the view in the direction of the controller cap.
Snaps
SR SNAP TO REMOTE OBJECTS / Snaps to objects that are not near the element.
Structure
STRUCTURAL FRAMING: BEAM / Adds a load-bearing structural beam element to the building
BM
model.
About Cookies on this site:
BR
Our site uses cookies and similar technologies. Manage your cookie preferences here. Further use of this site will be considered consent.
STRUCTURAL FRAMING: BRACE / Adds diagonal members that are connected to beams and
columns.
STRUCTURAL BEAM SYSTEM; AUTOMATIC BEAM SYSTEM / Creates a layout that is used to
BS
control the number and spacing of a series of parallel beams.
FT STRUCTURAL FOUNDATION: WALL / Creates a wall foundation for the building model.
REINFORCEMENT NUMBERS / Defines or edits numbering sequences by partition for rebar and
RN
fabric sheets.
System
DF DUCT FITTING / Places duct fittings (elbows, tees, end caps, and so on) in duct systems.
EE ELECTRICAL EQUIPMENT / Places electrical equipment, such as panels and switch gear.
RP About Cookies on this site:REFERENCE PLANE / Creates a reference plane using drawing tools.
Our site uses cookies and similar technologies. Manage your cookie preferences here. Further use of this site will be considered consent.
SK SPRINKLER / Places a sprinkler
View
FN9 SYSTEM BROWSER / Finds components that are not assigned to a system.
TL THIN LINES / Displays all lines on the screen as a single width, regardless of zoom level.
VISIBILITY/GRAPHICS / Controls the visibility and graphic display of model elements, datum
VG or VV
elements, and viewspecific elements for each view in a project.
WC CASCADE WINDOWS / Arranges all open windows in a series in the drawing area.
HIDDEN LINE / Displays the image with all edges and lines drawn except those obstructed by
HL
surfaces.
RH TOGGLE REVEAL HIDDEN ELEMENTS MODE / Toggles the Reveal Hidden Elements Mode.
RAY TRACE / Opens Ray Trace visual style, enabling a photorealistic rendering mode that
RY
allows panning and zooming around the model.
WIREFRAME / Displays the image of the model with all edges and lines drawn, but with no
WF
surfaces drawn.
Our site uses cookies and similar technologies. Manage your cookie preferences here. Further use of this site will be considered consent.
FOLLOW AUTODESK PRODUCTS SUPPORT & LEARNING BUY ABOUT AUTODESK
Facebook Free product trials Product support Online store Careers
Twitter 3D CAD software Learning & productivity Find a reseller Contact us
Character animation
Movie editing
Visual effects
Privacy/Cookies | About our Ads | Legal Notices & Trademarks | Report Noncompliance | Site map | 2017 Autodesk Inc. All rights reserved
Our site uses cookies and similar technologies. Manage your cookie preferences here. Further use of this site will be considered consent.