Documente Academic
Documente Profesional
Documente Cultură
Therefore, a mobile communication channel is uplink limited. An effective solution to improve the uplink reception is
adding a low noise amplifier (LNA), generally called tower mounted amplifier (TMA), masthead amplifier (MHA) or tower
top amplifier (TTA) in the uplink channel. TMAs improve the BTS reception as:
TMA is the closest element to the antenna and before the long tower cable
The signal loss due to the cable is compensated by the TMA gain
The noise figure of the system is determined by very low noise figure of the TMA (less than 2 dB) compared to
the cable loss
The minimum signal level that can be detected by the BTS receiver is improved which provides better receiver
sensitivity
Provide additional RX filtering
Improved receiver sensitivity by the TMA offers several advantages such as:
SDPs TMAs are designed to improve the uplink performance of the BTS receiver with the lowest noise figure and
highest reliability. SDP design addresses all the TMA needs of current and future wireless communication generations,
offering flexible solutions for every application.
Features
Double units for easy use with XPol antennas
Designed to support CWA, AISG 1.1 and AISG 2.0
(default)
Built-in lightning protection on RF and AISG ports
Bypass mode supported
Low insertion loss
Low Noise figure and high Gain
Low forward and reverse IMD
Stable thermal performance
AISG and DC supply can be connected at Port1 or
Port2
High IP3
Features
Double units for easy use with XPol antennas
Designed to support CWA, AISG 1.1 and AISG 2.0
(default)
Built-in lightning protection on RF and AISG ports
Bypass mode supported
Low insertion loss
Low Noise figure and high Gain
Low forward and reverse IMD
Stable thermal performance
AISG and DC supply can be connected at Port1 or
Port2
High IP3
Features
Double units for easy use with XPol antennas
Designed to support CWA, AISG 1.1 and AISG 2.0
(default)
Built-in lightning protection on RF and AISG ports
Bypass mode supported
Low insertion loss
Low Noise figure and high Gain
Low forward and reverse IMD
Stable thermal performance
AISG and DC supply can be connected at Port1 or
Port2
High IP3
Features
Double units for easy use with XPol antennas
Designed to support CWA, AISG 1.1 and AISG 2.0
(default)
Built-in lightning protection on RF and AISG ports
Bypass mode supported
Low insertion loss
Low Noise figure and high Gain
Low forward and reverse IMD
Stable thermal performance
AISG and DC supply can be connected at Port1 or
Port2
High IP3
Features
Double units for easy use with XPol antennas
Designed to support CWA, AISG 1.1 and AISG 2.0
(default)
Built-in lightning protection on RF and AISG ports
Bypass mode supported
Low insertion loss
Low Noise figure and high Gain
Low forward and reverse IMD
Stable thermal performance
AISG and DC supply can be connected at Port1 or
Port2
High IP3
Features
Double units for easy use with XPol antennas
Designed to support CWA, AISG 1.1 and AISG 2.0
(default)
Built-in lightning protection on RF and AISG ports
Bypass mode supported
Low insertion loss
Low Noise figure and high Gain
Low forward and reverse IMD
Stable thermal performance
AISG and DC supply can be connected at Port1 or
Port2
High IP3
Features
Double units for easy use with XPol antennas
Designed to support CWA, AISG 1.1 and AISG 2.0
(default)
Built-in lightning protection on RF and AISG ports
Bypass mode supported
Low insertion loss
Low Noise figure and high Gain
Low forward and reverse IMD
Stable thermal performance
AISG and DC supply can be connected at Port1 or
Port2
High IP3
Features
Double units for easy use with XPol antennas
Designed to support CWA, AISG 1.1 and AISG 2.0
(default)
Built-in lightning protection on RF and AISG ports
Bypass mode supported
Low insertion loss
Low Noise figure and high Gain
Low forward and reverse IMD
Stable thermal performance
AISG and DC supply can be connected at Port1 or
Port2
High IP3
Features
Double units for easy use with XPol antennas
Designed to support CWA, AISG 1.1 and AISG 2.0
(default)
Built-in lightning protection on RF and AISG ports
Bypass mode supported
Low insertion loss
Low Noise figure and high Gain
Low forward and reverse IMD
Stable thermal performance
AISG and DC supply can be connected at Port1 or
Port2
High IP3
Features
Double units for easy use with XPol antennas
Designed to support CWA, AISG 1.1 and AISG 2.0
(default)
Built-in lightning protection on RF and AISG ports
Bypass mode supported
Low insertion loss
Low Noise figure and high Gain
Low forward and reverse IMD
Stable thermal performance
AISG and DC supply can be connected at Port1 or
Port2
High IP3
Features
Double units for easy use with XPol antennas
Designed to support CWA, AISG 1.1 and AISG 2.0
(default)
Built-in lightning protection on RF and AISG ports
Bypass mode supported
Low insertion loss
Low Noise figure and high Gain
Low forward and reverse IMD
Stable thermal performance
AISG and DC supply can be connected at Port1 or
Port2
High IP3
Features
Double units for easy use with XPol antennas
Designed to support CWA, AISG 1.1 and AISG 2.0
(default)
Built-in lightning protection on RF and AISG ports
Bypass mode supported
Low insertion loss
Low Noise figure and high Gain
Low forward and reverse IMD
Stable thermal performance
AISG and DC supply can be connected at Port1 or
Port2
High IP3
MTMA-GSM1800-UMTS2100-12-CWA-AISG
TX channel specification
Frequency Band 1805-1880 MHz 2110-2170 MHz
Insertion loss 0.5 dB typical 0.35 dB typical
Return loss 18 dB 18 dB
200W (+53 dBm) CW/ 1.6KW (+62 200W (+53 dBm) CW/
Input power
dBm) Peak 1.6KW (+62 dBm) Peak
Intermodulation in RX band -160 dBc -160 dBc
RX channel specification
Frequency band 1710-1785 MHz 1920-1980 MHz
Gain over temperature 12 1.0 dB 12 1.0 dB
Noise figure at ambient 1.5 dB typical 1.5 dB typical
Noise figure over temp. 2.0 dB max 2.0 dB max
Return loss, Gain mode over temp. 18 dB 18 dB
Return loss, Bypass mode over
14 dB 14 dB
temp.
Insertion loss, Bypass mode over
2.7 dB typical 2.2 dB typical
temp.
Input P1 dB 3.0 dBm typical 3.0 dBm typical
Input IP3 13.0 dBm typical 13.0 dBm typical
Power supplier and Alarm (CWA mode)
Operating voltage 9-15 VDC
Operating current range per port 160 mA - 260 mA
Alarm current per port 450 mA - 590 mA
Maximum power consumption 3.5 W
Power supply (AISG mode)
Operating voltage 9-30 VDC
Total (both TMAs) operating current
Norm 360 mA at 9 V / Norm 90 mA at 30 V
(without RET)
AISG version AISG 1.1, AISG 2.0(default)
Firmware upgradeable Via AISG
Pin NC; Pin2 NC; Pin3 RS485B; Pin4 RS485 GND; Pin5 RS485A; Pin6
AISG connections
9-30 V; Pin7 DC return; Pin8 NC
Environment specifications
Maximum operating temperature -40 to 65 C
IP rating IP68
EMC ETS 300-342-2
Lightning protection IEC 61000-4-5
Mechanical specifications
Dimensions (without connectors) 251 x 210 x 129 mm
Weight 10.0 Kg
Connectors DIN 7/16 (F)
Mounting Vertical, Pole / Wall
MTMA-GSM1800-LTES2600-12-CWA-AISG
TX channel specification
Frequency Band 1805-1880 MHz 2620-2690 MHz
Insertion loss 0.5 dB typical 0.4 dB typical
Return loss 18 dB 18 dB
200W (+53 dBm) CW/ 1.6KW (+62 200W (+53 dBm) CW/
Input power
dBm) Peak 1.6KW (+62 dBm) Peak
Intermodulation in RX band -160 dBc -160 dBc
RX channel specification
Frequency band 1710-1785 MHz 2500-2570 MHz
Gain over temperature 12 1.0 dB 12 1.0 dB
Noise figure at ambient 1.5 dB typical 1.5 dB typical
Noise figure over temp. 2.0 dB max 2.2 dB max
Return loss, Gain mode over temp. 18 dB 18 dB
Return loss, Bypass mode over
14 dB 14 dB
temp.
Insertion loss, Bypass mode over
2.7 dB typical / 3.0 dB max 2.7 dB typical
temp.
Input P1 dB 3.0 dBm typical 3.5 dBm typical
Input IP3 13.0 dBm typical 13.0 dBm typical
Power supplier and Alarm (CWA mode)
Operating voltage 9-15 VDC
Operating current range per port 160 mA - 260 mA
Alarm current per port 450 mA - 590 mA
Maximum power consumption 3.5 W
Power supply (AISG mode)
Operating voltage 9-30 VDC
Total (both TMAs) operating current
Norm 360 mA at 9 V / Norm 90 mA at 30 V
(without RET)
AISG version AISG 1.1, AISG 2.0(default)
Firmware upgradeable Via AISG
Pin NC; Pin2 NC; Pin3 RS485B; Pin4 RS485 GND; Pin5 RS485A; Pin6
AISG connections
9-30 V; Pin7 DC return; Pin8 NC
Environment specifications
Maximum operating temperature -40 to 65 C
IP rating IP68
EMC ETS 300-342-2
Lightning protection IEC 61000-4-5
Mechanical specifications
Dimensions (without connectors) 251 x 210 x 129 mm
Weight 10.0 Kg
Connectors DIN 7/16 (F)
Mounting Vertical, Pole / Wall
MTMA-UMTS2100-LTES2600-12-CWA-AISG
TX channel specification
Frequency Band 2110-2170 MHz 2620-2690 MHz
Insertion loss 0.5 dB typical 0.4 dB typical
Return loss 18 dB 18 dB
200W (+53 dBm) CW/ 200W (+53 dBm) CW/
Input power
1.6KW (+62 dBm) Peak 1.6KW (+62 dBm) Peak
Intermodulation in RX band -160 dBc -160 dBc
RX channel specification
Frequency band 1920-1980 MHz 2500-2570 MHz
Gain over temperature 12 1.0 dB 12 1.0 dB
Noise figure at ambient 1.5 dB typical 1.5 dB typical
Noise figure over temp. 2.0 dB max 2.2 dB max
Return loss, Gain mode over temp. 18 dB 18 dB
Return loss, Bypass mode over
14 dB 14 dB
temp.
Insertion loss, Bypass mode over
2.2 dB typical 2.7 dB typical
temp.
Input P1 dB 3.0 dBm typical 3.5 dBm typical
Input IP3 13.0 dBm typical 13.0 dBm typical
Power supplier and Alarm (CWA mode)
Operating voltage 9-15 VDC
Operating current range per port 160 mA - 260 mA
Alarm current per port 450 mA - 590 mA
Maximum power consumption 3.5 W
Power supply (AISG mode)
Operating voltage 9-30 VDC
Total (both TMAs) operating current
Norm 360 mA at 9 V / Norm 90 mA at 30 V
(without RET)
AISG version AISG 1.1, AISG 2.0(default)
Firmware upgradeable Via AISG
Pin NC; Pin2 NC; Pin3 RS485B; Pin4 RS485 GND; Pin5 RS485A; Pin6
AISG connections
9-30 V; Pin7 DC return; Pin8 NC
Environment specifications
Maximum operating temperature -40 to 65 C
IP rating IP68
EMC ETS 300-342-2
Lightning protection IEC 61000-4-5
Mechanical specifications
Dimensions (without connectors) 210 x 180 x 109 mm
Weight 6.0 Kg
Connectors DIN 7/16 (F)
Mounting Vertical, Pole / Wall
MTMA-EU800-EGSM900-12-CWA-AISG
TX channel specification
Frequency Band 791-821 MHz 925-960 MHz
Insertion loss 0.5 dB typical 0.5 dB typical
Return loss 18 dB 18 dB
160W (+52 dBm) CW/ 200W (+53 dBm) CW/
Input power
1.6KW (+62 dBm) Peak 1.6KW (+62 dBm) Peak
Intermodulation in RX band -160 dBc -160 dBc
RX channel specification
Frequency band 832-862 MHz 880-915 MHz
Gain over temperature 12 1.0 dB 12 1.0 dB
Noise figure at ambient 1.6 dB typical 1.6 dB typical
Noise figure over temp. 2.0 dB max 2.0 dB max
Return loss, Gain mode over temp. 18 dB 18 dB
Return loss, Bypass mode over
14 dB 14 dB
temp.
Insertion loss, Bypass mode over
2.3 dB typical 2.5 dB typical
temp.
Input P1 dB 3.0 dBm typical 3.0 dBm typical
Input IP3 13.0 dBm typical 13.0 dBm typical
Power supplier and Alarm (CWA mode)
Operating voltage 9-15 VDC
Operating current range per port 160 mA - 260 mA
Alarm current per port 450 mA - 590 mA
Maximum power consumption 3.5 W
Power supply (AISG mode)
Operating voltage 9-30 VDC
Total (both TMAs) operating current
Norm 360 mA at 9 V / Norm 90 mA at 30 V
(without RET)
AISG version AISG 1.1, AISG 2.0(default)
Firmware upgradeable Via AISG
Pin NC; Pin2 NC; Pin3 RS485B; Pin4 RS485 GND; Pin5 RS485A; Pin6
AISG connections
9-30 V; Pin7 DC return; Pin8 NC
Environment specifications
Maximum operating temperature -40 to 65 C
IP rating IP68
EMC ETS 300-342-2
Lightning protection IEC 61000-4-5
Mechanical specifications
Dimensions (without connectors) 345.6 x 266 x 153 mm
Weight 12.0 Kg
Connectors DIN 7/16 (F)
Mounting Vertical, Pole / Wall
Features
Double unit with 900 MHz bypass for easy use with
XPol antennas
Designed to support CWA, AISG 1.1 and AISG 2.0
(default)
Built-in lightning protection on RF and AISG ports
Bypass mode supported
Low insertion loss
Low Noise figure and high Gain
Low forward and reverse IMD
Stable thermal performance
AISG and DC supply can be connected at Port1 or
Port2
Features
Double units for easy use with XPol antennas
Designed to support AISG 2.0
Built-in lightning protection on RF and AISG ports
Bypass mode to ensure base station operation
without DC power
Internal synchronization and control of TX/RX
operation
High power handling offered by in-house designed
specialized circulators
TX Channel Specifications
Part number TMA-185203 TMA-230240 TMA-257262
Frequency band 1850-2030 MHz 2300-2400 MHz 2570 - 2620 MHz
Insertion loss 1.1 dB typical
Return loss 18 dB min (BTS and ANT ports, gain and bypass modes)
CW power handling 50 dBm
Spurious and IMD
9kHz-1GHz: -36dBm , 1GHz-12.7 GHz: -30dBm
emission*
Signal type OFDMA
RX Channel Specifications
Frequency band 1850-2030 MHz 2300-2400 MHz 2570 - 2620 MHz
Gain over frequency and
12 1 dB max
temperature
Noise figure 1.7 dB typical, 2.2 dB max
Return loss 16 dB min, all ports
Insertion loss, bypass mode 3.5 dB max
Input P1dB 3 dBm min
IIP3 13 dBm min
Signal type SC-FDMA
Operation voltage 10-30 VDC
AISG version AISG 2.0
Firmware upgrade Via AISG
Pin1 NC; Pin2 NC; Pin3 RS485B; Pin4 RS485 GND; Pin5 RS485A; Pin6 10-30 V; Pin7
AISG connections
DC Return; Pin8 NC.
Environmental Specifications
Maximum operating
-40 to +65 C
temperature range
Lightning protection RF and AISG ports
MTBF > 500,000 hours
Ingress protection IP68
Mechanical Specifications
Dimensions 214 x 235.2 x 44.6 mm
Weight < 2 Kg
RF connectors N Female
* SDP Telecom Inc. offers customized internal or external filter solutions to control spurious response of the unit
depending on the customer requirements.
Features
Adjustable output voltage and alarm currents
independently
Enable/disable TMA output control using front panel
dip switches
ESD, short circuit, and reverse voltage protection for
output ports
RS485 communication port
Base Station Accessories
Electrical Specifications
20 to 60V dc isolated, stan-
Input voltage dard telecom +24V or -48V
configurations
6 outputs, 9-16V, adjustable
Output voltage for TMAs
voltage via GUI
Maximum output current
500 mA
per port
Maximum input current 3A
Aram output Isolated 3-pin relay connection
Mechanical Specifications
Connectors
Outputs for TMAs 6 SMB male
Power 4-pin male
General alarm 3-pin male
General communications 3-pin male
Indicators
TMA status indicator 6 bi-color LED
Power supply indicator One bi-color LED
Dimensions (HxWxD) 40 x 200 x 100 mm
Weight 0.5 kg max
Environmental Specifications
Storage ETS3019-1-1
Transportation ETS3019-1-2
Operation ETS3019-1-3
Housing IP40
Temperature Range
-40C to +65C
(Indoor Use)
Lightning Protection IEC 1000-4-5
Asian
Operational
Excellence
Components
In-Building
TMA (14-07) Rev A