Sunteți pe pagina 1din 4

Taylormade

Training
Consultants OTIS TYPE QUICK UNIONS

Thread Bore Seal Dia O-ring # Working Service


(B) ACME (A") (C") Press (psi)

5.00-4 2.50/2.92 3.500 338 10,000 Std


5.00-4 2.50/2.92 3.500 338 5,000 H2S
5.00-4 2.50/3.00 3.500 236 10,000 Std
5.00-4 2.50/3.00 3.500 236 5,000 H2S
5.00-4 2.50 3.500 338 15,000 H2S
5.75-4 3.00 4.000 342 10,000 H2S
6.00-4 4.00 4.875 349 5,000 Std
6.25-4 2.50 4.000 342 15,000 H2S
6.50-4 3.00 4.750 348 10,000 H2S
6.50-4 4.00 4.750 348 5,000 H2S
6.50-4 4.00 5.188 249 5,000 H2S
6.50-4 4.00 5.250 352 5,000 H2S
7.50-4 3.00 5.500 354 15,000 H2S
8.25-4 5.00 6.188 434 10,000 Std
8.25-4 5.00 6.188 434 5,000 H2S
8.375-4 4.00 5.250 427 10,000 H2S
8.75-4 6.38 7.500 441 5,000 H2S
9.00-4 5.00 6.750 438 10,000 H2S
9.50-4 6.38 8.000 443 5,000 H2S
9.50-4 4.00 6.250 435 15,000 H2S
11.50 6.38 8.25 444 10,000 H2S
12.00-4 7.38 10.313 448 5,000 H2S
12.25-4 5.12 7.00 439 15,000 H2S

C C
A A
Pin Box

Note : When selecting O-rings - ensure elastomer material is correct for well conditions

For full training manual and training : www.taylormadetc.com


TTC 1994. Subject to the Copyright Act 1968.
Taylormade
Training
Consultants BOWEN TYPE QUICK UNIONS

Thread Bore Seal Dia O-ring # Working Service


(B) ACME (A") (C") Press (psi)

4.75-4 2.50 3.750 340 10,000 Std


4.75-4 2.50 3.750 340 5,000 H2S
4.75-4 3.00 3.750 340 5,000 Std
5.50-4 x 2 3.00 4.375 345 5,000 H2S
5.50-4 x 2 3.00 4.375 345 10,000 Std
6.00-4 x 2 3.00 4.875 349 5,000 H2S
6.312-4 2.50/3.00 4.375 345 10,000 H2S
6.312-4 2.50 3.750 340 15,000 H2S
6.312-4 3.00 4.375 242 10,000 H2S
7.00-5SA 4.00 5.250 427 5,000 H2S
7.00-5SA 3.00 4.375 345 15,000 H2S
8.25-4 x 2 4.00 6.000 433 10,000 H2S
8.25-4 x 2 4.00 6.000 256 10,000 H2S
8.25-4 x 2 5.00 6.750 438 5,000 H2S
8.875-4 x 2 5.00 6.500 437 10,000 H2S
9.875-4 x 2 6.38 8.000 443 5,000 H2S
13.00-4 7.38 9.500 447 5,000 H2S
13.00-4 7.38 9.500 447 10,000 H2S
13.50-4 7.38 10.000 448 10,000 H2S

C
A C A
Pin Box

Lightweight and Hunting Unions

Thread Bore Seal Dia O-ring # Working Service


(B) ACME (A") (C") Press (psi)

4.75-4 x 2 3.00 3.750 340 10,000 H2S


6.125-4 x 2 4.12 4.750 348 10,000 H2S
11.50-4 7.38 8.625 445 5,000 H2S
12.00-4 x 2 9.00 10.313 376 5,000 H2S
14.125-4 x 2 6.38 9.000 1412 15,000 H2S
* Bowen threads designated "x 2" = double start threads

For full training manual and training : www.taylormadetc.com


TTC 1994. Subject to the Copyright Act 1968.
Taylormade
Training
Consultants PRESSURE FITTINGS

One of the common pressure fitting threads in the industry is NPT (National Pipe Thread), with 1/2"
NPT being a very common size.

NPT threads are slightly tapered by 1/16" over their length ( 3/4" taper per foot)and are usually used with
PTFE thread sealing tape.

Common size range : 1/8", 1/4" 3/8", 1/2", 3/4", 1", 1 1/4", and 1 1/2"

For full training manual and training : www.taylormadetc.com


TTC 1994. Subject to the Copyright Act 1968.
Taylormade
Training
Consultants PRESSURE FITTINGS

Hydraulic connections.

Snaptite Connections are used on all


hydraulic oil connections, such as the
hydraulic BOP's and the power pack
to reel pack connections.

Care should be taken to bleed off


trapped pressure before releasing
or connecting these fittings.

Huber Connections

These are used on high pressure

grease connections such as on the

supply and return drain hoses on the

Grease Injection Head (GIH) and

Grease Injection Unit (GIU).

Pneumatic (Air) Connections

The most common is the "Chicago"


type, which has a bayonet type twist
connection.

For safety a locking pin is inserted to


prevent the connection twisting open.

A safety cable connects the two


hoses to constrain their movement
in the event that they separate under
pressure.

For full training manual and training : www.taylormadetc.com


TTC 1994. Subject to the Copyright Act 1968.

S-ar putea să vă placă și