Documente Academic
Documente Profesional
Documente Cultură
www.cytec.com
REPRESENTATIVE APPLICATIONS SURFACE ACTIVE PROPERTIES
Low particle size at low usage levels
Critical Micelle Concentration
Can produce high solids latex at manageable (CMC), % by weight 29
viscosity
Gives latexes with good mechanical and electrolyte Surface tension, dynes/cm,
25C, Solutions with different
stability and low coagulum levels
concentration, A 102 % by
Latexes form clear films with good resistance to weight
moisture and yellowing 0.005 49.9
0.010 45.2
In combination with AEROSOL MA-80 I or AEROSOL 0.110 33.4
LF4 surfactants, gives excellent adhesion
Allows for incorporation of higher levels of water Interfacial tension, dynes/cm,
25C, 0.1% solution against
soluble specialty monomers, such as CYLINK NH8
mineral oil, after 5 minutes 7.2
wet adhesion monomer
Ross Miles Foam Test,
STORAGE AND HANDLING ASTM D-1173,
0.5% solution, 25C
It is recommended to store this material at ambient
Initial foam volume, ml 300
temperature. Foam volume after 15
minutes, mL 75
The efficacy of AEROSOL A-102 surfactant is not
impaired by freezing or thawing. However, if a Rewetting sulfur Excellent rewetting of
freezethaw cycle occurs, it is recommended to dry powder containing
0.1% surfactant
agitate the entire contents of the container prior to
use.
ELECTROLYTE TOLERANCE1
Handling and storage information on this product
can be found in the corresponding Cytec Industries Ca(NO3)2 4H2O Excellent2
Inc. Material Safety Data Sheet
MgSO4 (anhydrous) Excellent2
HEALTH AND SAFETY INFORMATION Ba(OH)2 8H2O Good3
Before handling this material, read the
corresponding Cytec Industries Inc. Material Safety FeCI3 6H2O Good3
Data Sheet for safety, health and environmental
AICI3 6H2O Poor-Fair4
data.
1
The information outlined above was obtained by first preparing 5%
surfactants solutions (100% active basis) and by adding drop wise to these
salt solutions.
2
ExcellentAble to infinitely dilute surfactant solution with salt solution. No
turbidity observed when the volume of surfactant solution was doubled with
the salt.
3
GoodThe first few drops of salt solution yield a precipitate which dissolves
on shaking. At 1:1 salt to surfactant volume ratio, a turbidity develops which
can be clarified by additional shaking.
4
Poor-FairAs dropwise addition of salt proceeds, turbidity develops at 1:1
volume ratio.
Email: custinfo@cytec.com Worldwide Contact Info: www.cytec.com US Toll Free: 800-652-6013 Tel: (+1) 973-357-3193
Disclaimer: Cytec Industries Inc. in its own name and on behalf of its affiliated companies (collectively, Cytec) decline any liability with respect to the use made by anyone of the information TRADEMARKNOTICE The indicatesaRegisteredTrademark in
contained herein. The information contained herein represents Cytecs best knowledge thereon without constituting any express or implied guarantee or warranty of any kind (including, but the United States and the or * indicates a Trademark in the
not limited to, regarding the accuracy, the completeness or relevance of the data set out herein). Nothing contained herein shall be construed as conferring any license or right under any patent United States. The mark may also be registered, the subject of an
or other intellectual property rights of Cytec or of any third party. The information relating to the products is given for information purposes only. No guarantee or warranty is provided that the application for registration or a trademark in other countries.
product and/or information is adapted for any specific use, performance or result and that product and/or information do not infringe any Cytec and/or third party intellectual property rights.
The user should perform its own tests to determine the suitability for a particular purpose. The final choice of use of a product and/or information as well as the investigation of any possible
violation of intellectual property rights of Cytec and/or third parties remains the sole responsibility of the user.