snepor7 ‘Space frame Wikipedia
Space frame
From Wikipedia, the free encyclopedia
In architecture and structural engineering, a space frame or space
structure is a truss-like, lightweight rigid structure constructed from
interlocking struts in a geometric pattern. Space frames can be used to
span large areas with few interior supports. Like the truss, a space frame is
strong because of the inherent rigidity of the triangle; flexing loads
(bending moments) are transmitted as tension and compression loads along
the length of each strut.
Contents
1 History
2. Design methods
3 Overview
4 Types
5 Applications
= 5.1 Construction
= 5.2 Vehicles
= 5.2.1 Aircraft
= 5.2.2 Cars
+ 5.2.3 Motorcycles and Bicycles
#6 See also
« 7 References
« 8 External links
History
Alexander Graham Bell from 1898 to 1908 developed space frames based
on tetrahedral geometry.!!l7] Bell's interest was primarily in using them to
make rigid frames for nautical and aeronautical engineering, with the
tetrahedral truss being one of his inventions. Dr. Ing. Max
Mengeringhausen developed the space grid system called MERO.
(acronym of MEngeringhausen ROhrbauweise) in 1943 in Germany, thus
initiating the use of space trusses in architecture.'! The commonly used
method, still in use has individual tubular members connected at node
joints (ball shaped) and variations such as the space deck system, octet
supported by a space frame structure.
|
If a force is applied to the blue node,
and the red bar is not present, the
behaviour of the structure depends
completely on the bending rigidity of
the blue node, If the red bar is present,
and the bending rigidity of the blue
node is negligible compared to the
contributing rigidity of the red bar, the
system can be calculated using a
rigidity matrix, neglecting angular
factors,
truss system and cubic system, Stéphane de Chateau in France invented the Tridirectional SDC system (1957),
Unibat system (1959), Pyramitec (1960).{4II5] A method of tree supports was developed to replace the indi
lual
columns.{l Buckminster Fuller patented the octet truss in 1961!7I while focusing on architectural structures.
Design methods
hps.on wikipoia orgtwikitSpace frame
6atanow ‘Space frame Wikipedia
Space frames are typically designed using a rigidity matrix. The special characteristic of the stiffness matrix in an
architectural space frame is the independence of the angular factors. If the joints are sufficiently rigid, the angular
deflections can be neglected, simplifying the calculations.
Overview
The simplest form of space frame is a horizontal slab of interlocking
square pyramids and tetrahedra built from aluminium or tubular steel
struts, In many ways this looks like the horizontal jib of a tower crane
repeated many times to make it wider, A stronger form is composed of
interlocking tetrahedra in which all the struts have unit length. More
technically this is referred to as an isotropic vector matrix or in a single
unit width an octet truss. More complex variations change the lengths
of the struts to curve the overall structure or may incorporate other
geometrical shapes. Simplified space frame roof with the half
octahedron highlighted in blue
Types
Within the meaning of space frame, we can find three systems clearly different between them:(8)
Curvature classification
= Space plane covers. These spatial structures are composed of planar substructures. Their behavior is similar
to that of a plate in which the deflections in the plane are channeled through the horizontal bars and the shear
forces are supported by the diagonals.!°
= Barrel vaults. This type of vault has a cross section of a simple
arch, Usually this type of space frame does not need to use
tetrahedral modules or pyramids as a part of its backing,
= Spherical domes and other compound curves usually require the
use of tetrahedral modules or pyramids and additional support
from a skin.
Classification by the arrangement of its elements
= Single layer grid. All elements are located on the surface to be
approximated.
= Double layer grid. The elements are organized in two layers
parallel to each other at a certain distance apart. Each of the
layers form a lattice of triangles, squares or hexagons in which
the projection of the nodes in a layer may overlap or be
displaced relative (o each other. Diagonal bars connect the nodes of both layers in different directions in
space. In this type of meshes, the elements are associated into three groups: upper cordon, cordon and
cordon lower diagonal
= Triple layer grid, Elements are placed in three parallel layers, linked by the diagonals. They are almost
always flat.
This train station is supported by a barrel
vaults structure,
Other examples we could attach with the definition of space frame are these:
= Pleated metallic structures. Emerged to try to solve the problems that formwork and pouring concrete had
their counterparts. Typically run with welded joint, but may raise prefabricated joints, a fact which makes
them space meshes.
hps.on wikipoia orgtwikitSpace frame 28snepor7 ‘Space frame Wikipedia
= Hanging covers. Designs on the cable taut, spine, and the catenary arch antifunicular show their ability to
channel forces theoretically better than any other alternative, have an infinite range of possibilities for
composition and adaptability to any type of plant cover or ensure vain. However, imprecisions in shape
having the loaded strand (ideally adapts dynamically to the state of charge) and the risk of bending the arc to
unexpected stresses are problems that require pre-compression and prestressing elements. Although in most
cases tend to be the cheapest and the technical solution that best fits the acoustics and ventilation of the
covered enclosure, are vulnerable to vibration.
= Pneumatic structures. Wherein the closure membrane is
subjected to a pressurized state, may be considered within this
‘group.
Applications
Construction
Space frames are a common feature in modem building construction;
they are often found in large roof spans in modemist commercial and
industrial buildings.
Examples of buildings based on space frames include:
Stansted airport, by Foster and Partners
Bank of China Tower and the Louvre Pyramid, by I. M. Pei
Rogers Centre by Rod Robbie and Michael Allan
McCormick Place East in Chicago
Eden Project in Cornwall, England
Globen, Sweden - Dome with diameter of 110 m, (1989)
Biosphere 2 by John P. Allen, Phil Hawes, Peter Jon Pearce in Oracle,
= Jacob K. Javits Convention Center, New York City, New York
The dome is a ‘parashell” concrete structure
and is the only one in Scotland. It was
‘constructed using a pioneering technique in
‘hich concrete was poured onto a special
neoprene membrane and then
pneumatically inflated.
, Arizona
Large portable stages and lighting gantries are also frequently built from space frames and octet trusses.
Vehicles
raft
‘The CAC CA-6 Wackett and Yeoman YA-1 Cropmaster 250R aircraft were
built using roughly the same welded stcel tube fuselage frame,
Cars
Spaceframes are sometimes used in the chassis designs of automobiles and
motorcycles. In both a spaceframe and a tube-frame chassis, the
suspension, engine, and body panels are attached to a skeletal frame of
tubes, and the body panels have little or no structural function. By contrast,
in a unibody or monocoque design, the body serves as part of the structure.
Tube-frame chassis pre-date spaceframe chassis and are a development of tl
Yeoman YA-1 vs CA-6 Wackett
frames.
the earlier ladder chassis. The advantage
of using tubes rather than the previous open channel sections is that they resist torsional forces better. Some tube
chassis were little more than a ladder chassis made with two large diameter
tubes, or even a single tube as a
backbone chassis. Although many tubular chassis developed additional tubes and were even described as
psn wikiposia orgwikitSpace frameavao%7 Spoce rame- Wikipedia
"spaceframes'", their design was rarely correctly stressed as a spaceframe and they behaved mechanically as a tube
ladder chassis, with additional brackets to support the attached components, suspension, engine etc. The distinction
of the true spaceframe is that all the forces in each strut are either tensile or compression, never bending.!!°1
Although these additional tubes did carry some extra load, they were rarely diagonalised into a rigid
spaceframe.[!]
The first true spaceframe chassis were produced in the 1930s by designers such as Buckminster Fuller and William
Bushnell Stout (the Dymaxion and the Stout Scarab) who understood the theory of the true spaceframe from either
architecture or aircraft design.|"11
The first racing car to attempt a spaceframe was the Cisitalia D46 of 1946.!"" This used two small diameter tubes
along each side, but they were spaced apart by vertical smaller tubes, and so were not diagonalised in any plane. A
year later, Porsche designed their Type 360 for Cisitalia. As this included diagonal tubes, it can be considered the
first true spaceframe.!!!)
The Maserati Tipo 61 of 1959 (Birdcage) is often thought of as the first but
in 1949 Dr, Robert Eberan-Eberhorst designed the Jowett Jupiter exhibited
at the London Motor Show in 1949 and taking a class win at the 1950 Le
Mans 24hr. Later the small British car manufacturers developed the concept
TVR produced an alloy-bodied two seater on a multi tubular chassis, which
appeared in 1949,
Colin Chapman of Lotus introduced his first ‘production’ car, the Mark VI,
in 1952, This was influenced by the Jaguar C-Type chassis, another with
four tubes of two different diameters, separated by narrower tubes.
Chapman reduced the main tube diameter for the lighter Lotus, but did not
reduce the minor tubes any further, possibly because he considered that this
would appear flimsy to buyers.!!°! Although widely described as a spaceframe, Lotus did not build a true
spaceframe chassis until the Mark VIII, with the influence of other designers, with experience from the aircraft
industry. {101
Jaguar C-Type frame
Other notable examples of space frame cars include the, Audi R8, Ferrari 360, Lamborghini Gallardo, Mercedes-
Benz SLS AMG and Pontiac Fiero.
‘A large number of kit cars, possibly the majority made in the UK, use space
frame construction, because manufacture in small quantity requires only
simple and inexpensive jigs, and it is relatively easy for an amateur
designer to achieve good stiffness with a space frame. Generally the space
frames are MIG welded, although the more expensive kits often use TIG
welding, a slower and more highly skilled process. Many of these resemble
the Lotus Mark VII in general outline and mechanical layout, however
others are close replicas of the AC Cobra or Italian supercars, but some are
original designs resembling no other vehicle. Often, considerable effort has
been made by the designers to produce true space frames, with all points of
significant load braced in 3 dimensions, resulting in strength and stiffhess
comparable to, or better than, typical production cars. Others are tube
frames but not true space frames because they use relatively large diameter
tubes, often curved, which are carrying bending loads, but due to the large diameter remain adequately rigid.
However some inferior designs are not true space frames, because the tubes are carrying considerable bending
Chilean kitcar showing off its
spaceframe structure (2013),
hps.on wikipoia orgtwikitSpace frame 46svrao%7 Space tame- Wikipedia
loads. This will result in considerable flexing due to dynamic loads, and ultimately fatigue fracture, a failure
mechanism which is rare in a correctly designed true space frame. The reduced stiffness will also impair the
handling.
‘A drawback of the spaceframe chassis is that it encloses much of the working volume of the car and can make
access for both the driver and to the engine difficult, Some spaceframes have been designed with removable
sections, joined by bolted pin joints. Such a structure had already been used around the engine of the Lotus Mark
111.2 Although somewhat inconvenient, an advantage of the spaceframe is that the same lack of bending forces in
the tubes that allow it to be modelled as a pin-jointed structure also means that such a removable section need not
reduce the strength of the assembled frame.
Motorcycles and Bicycles
Italian motorbike manufacturer Ducati
extensively uses tube frame chassis on
its models.
Space frames have also been used in
bicycles, such as those designed by
Alex Moulton.
Moulton Bicycle at the Museum of 2006 Ducati Monster $2R 1000,
Modern Art,
See also
Backbone chassis
Body-on-frame
Framing (construction)
Monocoque
Platonic solids
Stressed skin construction
Superleggera
Tensegrity
Tessellated roof
‘Tetrahedral-octahedral honeycomb
References
. "Alexander Graham Bell"
. Alexander Graham Bell (Tune 1903
. "Modular space grids",
"Unibat system’,
Claudia Estrela Porto (2014). "Stéphane de Chateau’s work" (PDF). Architectus. 4 (40): 51-64.
Evolution of Space Frames (http:/citiesnow.in/blog/2015/07/09/evolution-of-space-frames/) Archived (https://web.archiv
e.org/web/20151119115630/http://citiesnow.in/blog/2015/07/09/evolution-of-space-frames/) November 19, 2015, at the
‘Wayback Machine. Cities Now
Dorothy Harley Eber, via telephone (June 29, 1978). "Fuller on Bell”
Otero C. (1990). "Diseiio geométrico de ciipulas no esféricas aproximadas por mallas triangulares, con un ndimero
minimo de longitudes de barra’ Tesis Doctoral. Universidad de Cantabria.
9. Cavia Sorret (1993)
10, Ludvigsen & Colin Chapman, p. 153-154
11. Ludvigsen, Kar! (2010). Colin Chapman: Inside the Innovator. Haynes Publishing. pp. 150-164. ISBN 1-84425-413-5,
12. Ludvigsen & Colin Chapman, p. 151
"Tetrahedral Principle In Kite Structure". National Geographic Magazine, XIV (6).
hps.on wikipoia orgtwikitSpace frame 56avao%7 Space rame= Wikipedia
External links
= Information about space structures from the University of Surrey(no “Wikimedia Commons has
longer active) (http://www.surrey.ac.uk/eng/research/ems/ssrevintro.ht ame Commons is
" media related to Space
= Space frame manufacturer Company in India ) (http://www.aleox.in) frames.
Retrieved from "https://en. wikipedia org/w/index. php title-Space_frame8coldid=75 1530457"
Categories: Structural system | Structural engineering
= This page was last modified on 26 November 2016, at 08:32.
= Text is available under the Creative Commons Attribution-ShareAlike License; additional terms may apply.
By using this site, you agree to the Terms of Use and Privacy Policy. Wikipedia® is a registered trademark
of the Wikimedia Foundation, Inc., a non-profit organization
hps.on wikipoia orgtwikitSpace frame