Documente Academic
Documente Profesional
Documente Cultură
Solved by:
Abdullah Mahmoud
Sino & Tharwa Written Exam
1. Calculate the annular capacity between 12 hole and 8 D/Cs with 400 ft. length?
Capacity of tank bbl. /ft. = Volume in bbl. / height ft. = 53.5 bbl. /ft.
a Rig Tongs
b Chain Tong, pipe wrench
c Slips
d Safety Clamp
17. What are the two types of Rotating System? ()
A- Kelly System.
B-Top Drive System.
18. What are the two types of Valves that must be available on rig floor and what is the
position of each one?
() ()
a- IBOP: Initial Blowout PreventerPosition: Closed
b- FOSV: Full Opening Safety Valve. Position: Opened
19. If the no. of sheaves used in the crown block is 6, the no. of sheaves in the travelling
block is )(
a- 7 b- 6 c- 5
20. Torsion in the pin area of drill pipe tool joint is caused by the greatest wear in inner
diameter? ()
a. True b. False
21. From causes of drill collar failures, is to use improper amount of torque during trip
connection?()
a. True b. False
22. When considerable force is applied on the tongs floor man must not stand more
close to the breakout rotary tong line? )(
a. True b. False
23. The main functions of the drill pipe, is to put WOB?)(
a. True b. False
Sino & Tharwa Written Exam
24. Match the following? ()
a- Wash out () b- Slip cuts () c- Twist off ()
Slip cuts: Caused by a fatigue crack extended around the pipe
Wash out: Small opening caused by a fatigue crack penetrating the pipe wall
Twist off: Due to pipe turning in slips()
25. What are the drill collars types? ()
a-Slick b-Spiral
26. What are the drill collars functions?)(
a- Provide WOB which is necessary to drill.
b-Keep the drill string in tension to prevent the string buckling.
27. Mention three purposes of using dope when make-up drill pipes and collars?
()
a-To protect the thread during the connection.
b-To make lubricant between thread and box.
c-To prevent the Corrosion of threads.
28. When loading pipe on trucks or pipe racks, strips of wood should be placed between
each layer()
a. True b. False
If true, what is the minimum number of spacers should be use? No.=
29. Concerning the drill string care and handling practice, it a good practice to: (
)
I. Allow pipe to drop off truck onto the pipe rack. ()
a. True b. False
II. Avoid leaving a length of pipe unsupported, dont drag over the end of a pipe rack.
()
a. True b. False
Sino & Tharwa Written Exam
III. Clean pin and box threads before picking up Use Kerosene or other solvent.
()
a. True b. False
IV. Break out on trips with one set of tongs.)(
a. True b. False
V. Use threads protector ()
a. True b. False
VI. Drop the pipe on a hard surface such as edge of rotary or vee door ramp.
a. True b. False
30. Mention the steps for initial make up of new drill collars?
a-Make up with the proper torque.
b-Disconnect the new drill collar.
c-Make visual inspection on the thread.
31. Different types of drilling fluid and main function? ()
Types:-
A-Fresh water Muds B-Salt Water Muds c-Emulsion Muds
d-OBM e-Surfactant Muds
Functions:-
a-to exert the hydrostatic pressure which balanced with formation pressure.
b-to cool and lubricate the drill string.
c-to lift the cutting from the bottom of the well up to surface.
d-to suspend the cutting when circulation stopped.
e-to line up the wall of wellbore with thin permeable filter cake.
f-to support part of drill string and casing weight.
g-to provide energy require operating PDM.
h-to give good information about the penetrated formation.
Sino & Tharwa Written Exam
32. The Hydrogen Sulphide is lighter than air ()
a- False b- True
33. The flammable liquids fires can be extinguished by
()
a- CO2 b- Soda Ash c- Foam
34. CO2 is better than Halon in fire extinguishers: ( )
a. True b. False