Documente Academic
Documente Profesional
Documente Cultură
Copyright protection claimed includes all forms and matters of copyrightable material and information now
allowed by statutory judicial law or hereinafter granted, including without limitation, material generated from
the software programs displayed on the screen such as icons, screen displays, or looks.
Changes are periodically made to this document. Changes, technical inaccuracies, and typographic errors will be
corrected in subsequent editions.
3
The 700 Digital Color Press
Centerline Paper
All references to media capacity and performance in this document are based on centerline paper. You will see
the term Centerline paper several times in this document.
Customers may obtain a copy of the Xerox Recommended Materials List for the Xerox 700 Digital Color Press by
going to <http://www.xerox.com/downloads/usa/en/r/RML_700_DCP.pdf>
The Xerox 700 Digital Color Press is designed for an average monthly print volume range (AMPV Range):
The Xerox 700 Digital Color Press is designed to produce a consistent uniform-looking color image. The Xerox
700 Digital Color Press is designed to operate in the range of 20,000 75,000 copies or prints per month. The
number of copies or prints between service calls on a digital color copier / printer is highly dependent on
customer expectations of quality and the use of applications and throughput materials. At an average usage of
35,000 copies or prints per month using centerline paper, it is expected that service will be required about once
every 5 weeks.
4
Product Specifications
The following table contains the specifications for the performance of the Xerox 700 Digital Color Press.
5
Item Xerox 700 Digital Color Press Comments
* Status where paper feed can be started immediately when Start button is pressed.
** When M/C exits from Low Power mode after 1 hour from change to Low Power Mode.
6
Item Xerox 700 Digital Color Press Comments
Front to back registration on the Xerox 700 Digital Color Press is 1mm.
The following table contains more technical registration information regarding image registration,
magnification, and skew specifications for the Xerox 700 Digital Color Press.
Note: These specifications only apply to Xerox 700 Digital Color Press centerline paper measured on an 11 x 17
sheet.
Note: Environment (temperature, humidity), Type of Media, Media Cut, and part replacement may effect
alignment adjustments.
Note: The custom paper profiles tool (available through the UI) can be used to modify registration and skew settings for
specific papers; please refer to the User Guide for specific directions.
7
Product Caveats/Limitations
The maximum print/copy speed for the system is determined by the process speed of the Xerox 700 Digital
Color Press engine; image quality adjustments are done frequently to maintain consistent IQ.
As a printer / copier, the Xerox 700 Digital Color Press is a document printer; therefore, in reverse order
(face-up) printing the print engine will not cycle up until the entire job is ready. This will impact First Print
Out Time (FPOT). The printer may cycle down between each job depending on job complexity.
When printing, overall system performance (Click to Clunk time) is primarily dependent upon the software
applications and network environment being used. Rasterizing (RIP-ing) is only a small fraction of Click to
Clunk time.
Attempts to feed heavier than recommended paper stocks, and/or misuse of the media settings, may cause
machine damage or poor image quality. Using media at run modes other than that recommended for the
grade may cause poor image quality and serious machine damage.
If the requested finishing setting is outside machine capabilities:
Copy jobs will be sent through unfinished
Print jobs from the Creo and EFI color servers will be sent through unfinished
Print jobs from the FreeFlow color server will be held
45-36x faults may occur intermittently. The expected frequency is approximately once every 20,000 prints
or once a week, depending on print volume. To recover, power off and power on the printer.
127-211 / 311 faults may occur after jam clearance. To recover, Power Off/ Power On the printer.
System requirements messages (e.g., Order Waste Toner Container, Hole Punch Waste Container Full)
may occasionally be blocked by the current UI screen. Close the Job Status screen and open the Machine
Status/Supplies screen to check consumable status.
If the machine stops running mid-job, or does not begin printing after a job is submitted, check the
Machine Status/Supplies screen to determine if supplies need to be replaced. The system will stop if
sufficient supplies are not available for a submitted job. If the problem persists, check the Machine
Status/Fault screen, select the fault, and click on the Instructions button.
If the machine stops running mid-job, or does not begin printing after a job is submitted, verify that the
applicable paper tray is not empty. The system will stop if sufficient media is not available for a submitted
job. If the problem persists, check the Machine Status/Fault screen, select the fault, and click on the
Instructions button.
The system does not prohibit duplexing coated substrates from the internal trays (Trays 1-3); however,
there can be a significant increase in jams or multi-feeds. If large quantities of coated paper are to be run,
the OHCF is recommended for paper feeding.
When using heavy coated 11 x 17 stock, closing Trays 1-3 with too much force will result in a paper size
misread. Open and close the tray gently to allow the paper sensors to correctly identify paper size.
If the adjustment arms are disturbed while re-loading paper in Tray 5, the paper size setting will return to
default and cause job to stop until the paper size setting is corrected by the user.
8
Media Selection Guidelines
The following paper types are recommended to ensure you receive the best image quality from your Xerox 700
Digital Color Press:
Media Type Xerox Equivalent
Uncoated North America - Xerox Color Xpressions Plus Xerox 700 Digital
paper (90 g/m2/24 lbs) Color Press centerline
Europe Colotech+ (90 g/m2/24 lbs) paper
Coated paper North America Xerox Digital Color Elite Gloss 80# Text Xerox 700 Digital
(120 g/m2) Color Press centerline
Europe Xerox Digital Color Elite Gloss 80# Text (120 paper
g/m2)
Every effort has been made to ensure that the Xerox 700 Digital Color Press supports a broad range of
media. Keep in mind, however, that using only Xerox-recommended media maximizes reliability and paper-
handling performance.
For further information and recommendations regarding media selection and handling, refer to the
Material Usage Guide provided with your system and the Recommended Materials List (RML) available
from your Xerox representative or at <http://www.xerox.com/downloads/usa/en/r/RML_700_DCP.pdf>.
Typically, heavy weight papers exhibit increased variability of formation and surface smoothness, which
may result in degraded image quality.
Paper from all trays is printed topside first. It is recommended that Xerox branded paper be loaded with
ream wrapper seam-side up.
Manufacturers of coated stock do not recommend use of their media when the ambient relative humidity
exceeds 60%. Relative humidity greater than 40% may increase multi-feeds from Trays 1, 2, 3 and 5.
All paper stretches to a certain extent during printing. The amount of stretch is dependent on paper type
and environmental conditions. Stretch is most noticeable on coated stocks. This stretch can affect front-to-
back image registration. Use the Alignment Profiles feature described in the System Administration Guide
for instructions on how to minimize this effect.
Image registration, image quality (i.e. white spots), and machine reliability can be adversely affected when
custom-cut paper is inaccurately cut, is of poor quality, or loose paper fibers are present on the cut edges.
Image registration, image quality (i.e. white spots), jam frequency and machine reliability can be adversely
affected when punched or drilled paper is of poor quality and/or loose hole plugs are present in the ream.
9
Print Engine Productivity Speeds- IPM (Impressions per Minute)
Note: Productivity in these charts is based on images per minute (ipm), not prints per minute (ppm)
Note: Productivity in these charts applies to jobs run on a single media; switching trays within a job will
impact job productivity.
Unless otherwise specified, IPM numbers refer to simplex, duplex, color and BW prints or copies.
Paper Size
Internal Paper
A4 SEF, B4 SEF, A3 SEF
Trays (Trays 1-
A4 LEF, 8.5 x 11 8.5 x 11 8.5 x 14 11 x 17 13 x
3) and all
HCFs B5 LEF LEF SEF SEF SEF 19.2
210 mm 216 mm 298 mm 365 mm 432 mm 488 mm
Uncoated
64-176 g/m2 51
Simplex
71 70 39 35 31
46
Duplex
177-220 g/m2 51 51
Simplex Simplex
35 30 25 22
46 46
Duplex Duplex
221-256 g/m2 51 51 35 30 25 22
2
257-300 g/m 35 35 25 21 17 15
Coated
106-176 g/m2 51 51 22
Simplex Simplex Simplex
35 30 25
46 46 10.5
Duplex Duplex Duplex
177-220 g/m2 35 35
Simplex Simplex
25 21 17 15
31 31
Duplex Duplex
221-300 g/m2 35 35 25 21 17 15
10
Paper Size
Internal Paper A4 SEF, B4 SEF, A3 SEF
Trays (Trays 1- A4 LEF, 8.5 x 11 8.5 x 11 8.5 x 14 11 x 17
3) and all
HCFs B5 LEF LEF SEF SEF SEF 13 x 19.2
210 mm 216 mm 298 mm 365 mm 432 mm 488 mm
Transparency
B/W
40* 40 29 NA NA NA
w/ Finisher
B/W
w/o Finisher 40* 40 29 NA NA NA
Full Color
18* 18 13 NA NA NA
w/Finisher
Full Color
9* 9 8 NA NA NA
w/o Finisher
Tab paper
106-176 g/m2
32 32 NA NA NA NA
177-256 g/m2
23 23 NA NA NA NA
257-300 g/m2
16 16 NA NA NA NA
11
Note: Productivity in these charts is based on images per minute (ipm), not prints per minute (ppm)
Note: Productivity in these charts applies to jobs run on a single media; switching trays within a job will impact job
productivity.
Unless otherwise specified, IPM numbers refer to simplex, duplex, color and BW prints or copies.
Paper Size
Coated**
106-176 g/m2 * 40 40
Simplex Simplex
32 27 24 22
36 36
Duplex Duplex
177-220 g/m2 25 25 19 17 15 14
2
221-300 g/m 25 25 19 17 15 14
Transparency
B/W
40 40 29 NA NA NA
w/ Finisher
B/W
40 40 29 NA NA NA
w/o Finisher
Full Color
23 23 15 NA NA NA
w/Finisher
Full Color
9 9 8 NA NA NA
w/o Finisher
Tab paper
106-176 g/m2
32 32 NA NA NA NA
177-256 g/m2
23 23 NA NA NA NA
257-300 g/m2
16 16 NA NA NA NA
*running lightweight (less than 140 g/m2) coated stock through Tray 5 is not recommended
*environmental conditions may require that coated paper be fed one sheet at a time through Tray 5
12
Image Quality
With its low melt EA toner properties and higher print speed, the Xerox 700 Digital Color Press will produce
output with a lower gloss level that is consistent with offset.
As with any printing process, artifacts will occur. These include streaks, mottle, banding, spots, etc. For
most jobs and clients, the expected level of artifacts is within the normal operational and component
quality ranges of the system and will not affect the acceptability of the job. Maintenance procedures are
available to mitigate these artifacts.
Artifacts may occur with more frequency when running heavyweight coated media.
Artifact-sensitive jobs should be monitored.
Using products on the Recommended Materials List (RML) and maintaining your environment will also help
to minimize the occurrence of these artifacts.
Color quality perception is subjective and will be affected by ambient lighting conditions.
The appearance of the document displayed on the monitor screen may not match the output print because
the monitor uses RGB color space parameters.
The customer is responsible for calibrating the Xerox 700 Digital Color Press.
Image quality is strongly influenced by paper surface structure, texture, and color. To ensure that your
customers are optimally satisfied, key applications should be printed on the Xerox 700 Digital Color Press
using representative paper and reviewed by the customer.
The surface texture of some uncoated papers may cause increased graininess in halftone areas printed with
only black toner. This effect may be minimized by adding process black and/or using smooth or coated
papers (refer to the Recommended Materials List).
Sheets of a job may exhibit slight gloss differential from page to page. Operational mode will have an
impact on the level of gloss differential.
Prints may exhibit random white spots caused by paper dust, stray developer beads, or other miscellaneous
particles. You can reduce the occurrence of white spots by using Xerox approved paper. If you are cutting
your own paper, ensure that cut edges are dust free, and keep the machine in a clean and dust/dirt reduced
environment. Failure to do this will result in increased frequency of white spots.
To extend the life of your fuser, Xerox recommends the usage of multiple fusers. Multiple fusers provide
maximum copy/print output for longer periods of time and ensure image defects and wear lines on output
are avoided. Depending on the types of jobs run and their frequency, you may want more than one fuser
available:
one fuser roll for smaller paper
one fuser for larger paper
Always refer to your User Guide for information and hints and tips on using your fuser to its maximum life
capacity.
The Xerox 700 Digital Color Press is optimized for most media; specific media may result in curl which can be
corrected using the internal de-curlers on the print engine and the optional Interface Module (IFM) and
optional Light Production C Finisher.
13
Non-Standard paper sizes
The Xerox 700 Digital Color Press supports non-standard paper sizes. However, due to rounding and unit-
conversions that occur in the client applications, print server, and printer, some mismatch may occur between
the paper size entered at the application, and the paper size that must be entered at the printer. The operator
may need to adjust the entered paper dimensions by up to 0.1 in (2.5 mm) in order for the printer to detect that
the requested paper size has been loaded. In addition, the printer interprets some paper sizes included in the
PPD as non-standard sizes.
Duplex Prints
The Duplexing Automatic Document Feeder (DADF) for hardcopy scanning will handle originals from 5.5 x
8.5 to 11 x 17 (or A3) in size, and from 16 to 28lb Bond in weight. The DADF has a maximum capacity of
250 sheets (based on 24lb Paper).
Automatic duplexing can be done on all sizes of media, up to 80# Cover (220 g/m2).
Manual duplexing can be performed on media up to 110lb Cover (300 g/m2) or coated 100lb Cover (280
g/m2) from Tray 5 (Bypass).
Manual duplex can be performed on media up to 13x19" (SRA3 320mm x 450mm / Maximum 320mm x
482mm) from Tray 5 (Bypass). (Note: Image quality degradation is possible above 220 g/m2.)
As with any printer or copier, duplex performance is not expected to match the performance for single-
sided copying. Paper jam rates may be higher than the rate you will experience for the same throughput
material in single sided mode.
Integrated Scanner
250 sheet capacity (90 g/m2)
Originals up to 11 x 17 (A3) in weights from 38 gsm (16 lb bond) to 200 gsm (53 lb bond)
Duplex Automatic Document Feeder (DADF)
Scan resolution: 200 x 200, 300 x 300, 400 x 400, 600 x 600 dpi
Scan to FTP
14
Paper/Throughput
For more detailed information on throughput materials, please refer to the Xerox Materials Usage Guide and
the Recommended Materials List.
Recommended paper to maximize image quality and product reliability is Xerox Color Xpressions Plus (90
g/m2/24 lbs) or Colotech+ (90 g/m2/24 lbs) (smooth bright white paper). This paper is specifically designed
to maximize image quality and machine performance over a wide range of environmental conditions.
Attempts to feed heavier than recommended paper stocks, and/or misuse of the media settings, may cause
machine damage or poor image quality. Using media at run modes other than that recommended for the
grade may cause poor image quality and serious machine damage.
Note: There is no Tray # 4 on the Xerox 700 Digital Color Press.
All paper trays can be reloaded while jobs are running from any other tray. It is not possible to change
paper settings while jobs are running.
15
Transparencies
The Xerox 700 Digital Color Press will feed 8.5 in x 11 in/A4 transparencies at a speed of 23 ppm color. Use
Xerox removable stripe transparency material (USA and Canada: 3R3028, 3R3108; Xerox Europe: 3R98199,
3R3108 ) for optimum system performance and image projection. These premium transparencies are
specifically designed to provide optimum copy quality. Use of other transparencies may cause machine damage
and result in excessive service calls.
Due to the increased thickness of the removable stripe, no more than (100) 3R3108 transparencies should be
loaded in a paper tray at one time. The maximum output stack height should not exceed 100 transparencies.
Envelopes
The Xerox 700 Digital Color currently supports running the following European and Asian envelopes through
Tray 5:
Envelopes must be placed with the opened flap set as trail edge.
16
Recommended Supplies
Yield Projection
at representative
total area
coverage
Supply Cartridges (using centerline
Description Reorder Number per Carton paper)
WW WH/ XE DMO 30%
Metered Sold Toner Sold Toner (7.5%
Dry Ink: * Toner Reorder Reorder per color)
Reorder Number Number
Number
Black 6R1375 6R1383 6R1379 1 20k per
cartridge***
Cyan 6R1376 6R1384 6R1380 1 22k
Yellow 6R1378 6R1386 6R1382 1 22k
Magenta 6R1377 6R1385 6R1381 1 21k
Drum
Cartridge**:
Black 13R642 1 373k at
100%Black/White
354k at 100%
Color
Cyan 13R643 1 156k
Yellow 13R643 1 156k
Magenta 13R643 1 156k
Toner Waste 8R12990 33k
Bottle* 1
Contact the Welcome Center for replacement
Charge 13R637 175k
1
Corotron
Fuser Module 8R13065 1 200k
Convenience 8R12964
and Advance 5,000 staples
1
Staple
Cartridge
Convenience 3 staple refills
and Advance 8R12941 8R12941 8R12941 (5,000
Staple Refills staples each)
Light
4 staple refills
Production C
8R13041 8R13041 8R13041 (5,000
Finisher
staples each)
Staples
All Booklet makers
Booklet 4 staple refills (Professional and
Maker Staple 8R12925 8R12925 8R12925 (5,000 Light Production
Refill staples each) C) use this Staple
Refill
* The dry ink yield projections are based on the indicated area coverage at standardized conditions on 8.5 in x 11 in/A4
Xerox 700 Digital Color Press centerline paper. Please note that actual yields vary greatly depending on color intensity, area
coverage, paper stock, and mode selected.
17
** Drum Cartridge replacement frequency noted above for 8.5 in x 11 in/A4 images when using Xerox 700 Digital Color Press
centerline paper and other stocks with equivalent smoothness, cut quality and structure. Replacement rates may be more
frequent for operations which use high percentages of coated stocks, have area coverage greater than 70% of each color,
and/or larger than 8.5 in x 11 in/A4 size throughputs, e.g., 11 in x 17 in/A3.
*** One black cartridge per carton; two black cartridges are used in tandem, with a resulting yield of 40k.
Initial Supplies
Each Xerox 700 Digital Color Press is delivered with an initial supply of Toner as well as the CRUs (Drum
Cartridges, Charge Corotron, Fuser, and Waste Toner Container as well as Staples included for finishing
options with stapling).
To order additional Supply (toner / staples) or Throughput materials, contact the Xerox Supplies Marketing
Center :
1-800-822-2200 US, 1-800-668-0199 CAN (English), 1-800-668-0133 CAN (French.)
US Customers on Metered Price Plans should call the Metered Hotline, U.S. 1800599-2198 to acquire
additional toner.
Electrical Requirements:
Area Power Voltage (V) Frequency (Hz)
XC 208-240V-10%/+6% 50/60+/-3%
XE 220-240V+/-10% 50/60+/-3%
A single power cord (US receptacle diagram shown at left) is required for the Xerox
700 Digital Color Press.
NEMA 6-15R
18
Optional Feeders and Finishers:
With the exception of the HCF, Advanced Finisher and Professional Finisher, each optional feeding and finishing
device requires an additional 100-240VAC country-specific power receptacle.
15A-125V 20A-125V
NEMA 5-15R NEMA 5-20R
19
To determine Amp circuit requirements for accessories, add Amps from Current / Run Power column above:
1. Add Amps of each device.
2. If total amps are 12 or below, a 15 amp circuit may be used with NEMA 5-15R; however, a 20 amp circuit is
recommended using NEMA 5-20R receptacles.
3. If total amps are 12.1 through 16, a 20 amp circuit is required.
4. Total number of receptacles required is determined by total number of accessories.
Example 1:
2-tray OHCF (5 amps) + Light Production C Finisher (2 amps) + Interface Module (2.5 amps) = 9.5 amps.
A 15 amp circuit may be use with 3 receptacles (NEMA 5-15R) for each device.
Example 2:
2-tray OHCF (5 amps) + Light Production C Finisher (2 amps) + Interface Module (2.5 amps) + FreeFlow Server
(6.9 amps) + Monitor (1.2 amps) + FreeFlow Professional Package (.3 amps) = 17.9 amps.
Recommended Wall Receptacle Placement for Xerox 700 Digital Color Press and accessories (US
receptacles shown):
It is recommended that receptacles be grouped as shown in relation to the Xerox 700 Digital Color Press.
20
Installation Considerations
Ground Fault Protection is provided which meets Xerox internal safety requirements and exceeds the
Industry Standards for Information Technology Equipment.
Physical delivery of Xerox 700 Digital Color Press will be by a Xerox authorized D/R carrier. The carrier will
install and perform a functional check of the printer/copier unit. The carrier will review the
software/documentation with the customer. For the printer / copier the customer is responsible for
connecting and configuring the equipment on their network.
With the exception of the HCF, Advanced Finisher and Professional Finisher, each optional feeding and
finishing device requires an additional 100-240VAC country-specific power receptacle.
The unit weighs 583 lbs. (265 kg) - Printer, Scanner, and DADF. The Light Production Finisher with booklet
maker, interposer and folder is 392 lbs. (178 kg).
Power cords for the feeders, finishers and print engine are 8 2 (2490mm) long.
Power cords for the Print Servers are approximately 7.5 feet (2.3 meters).
The outbound Print Server video cables measure approximately 16.4 feet (5 meters).
One network drop is required for installation as a printer / copier.
There should be a minimum of 78 inches (1,981 mm) clearance from the floor to the nearest overhead
obstruction.
The service area (including device dimensions) from front to back is always 102 (2591 mm).
Electrical requirements and space requirements must be satisfied before the equipment is delivered.
Environmental Requirements
*Manufacturers of coated stock do not recommend use of their media when the ambient relative
humidity exceeds 60%
**Stated as an average. Warm up power consumption is 1,600 VA
21
Moveable and Stationary Installations
The following configurations can be moved by one person, and can therefore be considered moveable:
o A Xerox 700 Digital Color Press system consisting of the print engine and the offset catch tray
o A Xerox 700 Digital Color Press system consisting of the print engine and the Advanced
Finisher
o A Xerox 700 Digital Color Press system consisting of the print engine and the Professional
Finisher
o A Xerox 700 Digital Color Press system consisting of the print engine, Interface Module and
Light Production C Finisher
o A Xerox 700 Digital Color Press system consisting of the print engine, Interface Module and
High Capacity Stacker
Larger systems must be considered stationary due to the amount of force required to move the
system.
Carpeted flooring surfaces require the installation of a mobility plate.
Mobility plates are available from your Sales Representative.
22
Space Requirements
All standard Xerox space requirements apply to this installation including overhead, shared, aisle or hallway,
and operator space.
There should be a minimum of 78 inches (1,981 mm) clearance from the floor to the nearest overhead
obstruction.
To enable a Xerox Service Representative to safely repair the system, the work area must measure at least
36 (91.44 cm) square around the print server.
The service area (including device dimensions) from front to back is always 102 (2591 mm).
The dimensions listed below provide the overall service space required, including the space to the nearest
obstruction. The dimensions reflect both typical and hallway installations and are absolute minimums.
Please note: These dimensions do not include space required for the Print Server. Refer to the print server CED
for space requirements.
D1 D2
FEEDER IOT FINISHER
C
B
23
Physical Dimensions
The following table shows the overall physical dimensions of each module of the Xerox 700 Digital Color Press,
including space between the modules when connected into a system.
24
Dimensions for Several Configurations of the Xerox 700 Digital Color Press:
25
Configuration Width* Depth Height Weight
Optional Accessories
Accessory Description
High Capacity 2,000 sheet capacity ( based on 80 g/m2centerline paper)
Feeder
1 Tray
2,000 Sheet* (up to 13x19.2/SRA3) capacity from 64-300 g/m2 (uncoated) and
Oversize High 106-300 g/m2 (coated).
Capacity Feeder
2 Tray
4,000 Sheet* (up to 13x19.2/SRA3) capacity from 64-300 g/m2 (uncoated) and
Oversize High 106-300 g/m2 (coated).
Capacity Feeder
The Interface Module aligns the paper paths of the engine and finisher, cools
Interface and decurls paper exiting the printer, and allows communication between the
Module engine and finisher. One Interface Module is required on systems with
optional Light Production C Finisher and/or High Capacity Stacker.
Advanced
500 sheet top tray, 3,000 sheet stacker tray
Finisher
Professional
500 sheet top tray, 1,500 sheet stacker tray, Up to 20 set booklet tray
Finisher
26
The GBC AdvancedPunch is an inline die punch that utilizes modular die sets to
enable a variety of hole-punch patterns in A4/8 x 11 in (LTR) long-edge-fed
GBC media.
AdvancedPunch
LTR die punch ships with 19-hole die set
A4 die punch ships with 21-hole die set
The Light Production C Finisher includes a basic in-line punch, stapler, the stacker
tray and top exit tray.
Light Production
C Finisher It also includes a built-in decurler unit that corrects the curl on paper output from
the print engine, and a built-in interposer that feeds cover paper to finisher for
saddle-staple operation.
The Light Production C Finisher with booklet unit includes a basic in-line punch,
stapler, the stacker tray and top exit tray, and a booklet unit capable of saddle
Light Production stapling and bi fold.
C Finisher with
Booklet maker It also includes a built-in decurler unit that corrects the curl on paper output from
the print engine, and a built-in interposer that feeds cover paper to finisher for
saddle-staple operation.
An optional Folder unit that can handle Z-fold, Tri-C, and Tri-Z, it can be added to
the Light Production C Finisher or the Light Production C Finisher with Booklet
maker
C/Z Folder The C/Z folding tray can accommodate up to 40 sheets of 24 lb (90 g/m2)
media).
Supported Paper sizes are 8.5x11 (A4)
Allows C/Z folding of media up to 24 lb (90 g/m2) uncoated.
Stack up to 5,000 sheets* offsetting output stack tray with movable cart to move
to off line finishing. Additional cart is available for customer to order.
High Capacity
500 sheet* top tray, 64 g/m2- 300 g/m2, up to 13 x 19.2 in (330x488mm)
Stacker
Sample Set 1.) Programmable at Color Server or 2.) On-Demand at HCS User
Interface
Foreign Enables the connection of external devices such as auditrons or coin-op devices.
Interface Kit This will perform in copy and print modes.
Convenience
Staple up to 50 sheets of 90 g/m2 / 24 lb. media.
Stapler
2
*based on 80 g/m centerline paper
at launch this feature is available only with the FreeFlow server. Creo and EFI servers will offer this capability post-launch.
27
Combination of Output Functions and Destinations
Bi-fold
Top Stack Hole C-Z
Finisher Staple Booklet (Single Interposer
Tray Tray Punch Fold
Fold)
Advanced
o o o o
Finisher
Professional
o o o o o o
Finisher
Light
Production C
o o o o o
Finisher (LPC
Finisher)
LPC Finisher
o o o o o o
w/C-Z fold
LPC Finisher w/
o o o o o o o
Booklet Maker
LPC Finisher w/
Booklet Maker o o o o o o o o
and C-Z fold
High Capacity
o o
Stacker
28
Optional Oversized High Capacity Feeder (OHCF)
1 or 2 tray OHCF (each tray requires a fan kit)
Handles coated substrates up to 220 g/m2 for auto duplex
Air-assisted, robust feeder design for oversized and heavyweight
2,000 sheet capacity (80 g/m2 centerline paper)
Maximum paper size 13 x 19.2 in./SRA3
Weight range: from 64-300 g/m2 (uncoated) and 106-300 g/m2 (coated)
Maximum auto duplex up to 220 g/m2 /80 lb. cover, coated and uncoated
Requires an additional electrical receptacle (see Electrical Requirements section).
29
Advanced Finisher
500 sheet top tray, 3,000 sheet stacker tray
paper side registration 6mm
staple paper stack height 5.7 mm (0.22 in)
50-sheet, multi-position stapling
The Advanced Finisher offers Hole Punch as a standard feature.
Hole punch capacity is equal to the regular capacity of the chosen output tray. For the
US, 2- and 3-hole punching is available; for Europe, 2- and 4- hole punch is available.
Stacks can be punched on the left or right side, or on the top edge. If hole punching
fails, check to make sure that the punch waste container is empty before calling for
service.
Powered by print engine no external power source required
52-216 g/m2 uncoated stock to all trays
217-280 g/m2 uncoated stock to top tray only
Professional Finisher
500 sheet top tray, 1,500 sheet stacker tray
paper side registration 6mm
staple paper stack height 5.7 mm (0.22 in)
50-sheet, multi-position stapling
The Professional Finisher offers Hole Punch as a standard feature.
Hole punch capacity is equal to the regular capacity of the chosen output tray. For the
US, 2- and 3-hole punching is available; for Europe, 2- and 4-hole punch is available.
Stacks can be punched on the left or right side, or on the top edge.If hole punching
fails, check to make sure that the punch waste container is empty before calling for
service.
Powered by print engine no external power source required
52-216 g/m2 uncoated stock to all trays
217-280 g/m2 uncoated stock to top tray only
Up to 20 set booklet tray:
Stapled: 15 sheets/set (up to 90 g/m2 uncoated stock)
Non-stapled: 5 sheets/set
Bi-Fold (Single Fold): 1 sheet/set, up to 169 g/m2 uncoated stock
Stackable number of sets depends on paper size
30
Optional High Capacity Stacker (HCS)
The HCS is designed for long production runs.
Up to 5,000 sheets offsetting output stack tray with movable cart to move to
off- line finishing. Additional cart is available for customer to order.
Sample Set 1.) Programmable at Color Server or 2.) On-Demand at HCS User
Interface.
Requires an additional electrical receptacle (see Electrical Requirements section).
Combined finishing (attaching a HCS and Light Production C Finisher together in
a system) is available with external Print Servers only.
Attaching a HCS and Light Production C Finisher together in a system with the
Integrated Print Server will result in all jobs being sent unfinished to the top tray
of the HCS until the second finisher is detached from the system, and the
system is rebooted.
Paper Size
203 x 330 x
182 488
(mm) A4 B4 A3 SRA3 (mm)
Paper weight 8 x 7.16 8.5 x 11 8.5 x 14 11 x 17 12 x 18 13 x
and finish (in) (in) (in) (in) (in) 19.2 (in)
Uncoated
52-80 Sheet
5,000 5,000 5,000 5,000 5,000 5,000 5,000
g/m2 Qty
81- 570mm 570mm 570mm 570mm 570mm 570mm
Stack 570mm
300
Height (22.44 ) (22.44 ) (22.44 ) (22.44 ) (22.44 ) (22.44 ) (22.44 )
g/m2
Coated
105- 570mm 570mm 570mm 570mm 570mm 570mm
Stack 570mm
300
Height (22.44 ) (22.44 ) (22.44 ) (22.44 ) (22.44 ) (22.44 ) (22.44 )
g/m2
31
Optional Interface Module (IFM)
The Interface Module aligns the paper paths of the engine and finisher, cools and
decurls paper exiting the printer, and allows communication between the engine and
finisher.
One Interface Module is required on systems with optional Light Production C Finisher
and/or High Capacity Stacker.
Requires an additional electrical receptacle (see Electrical Requirements section).
The Light Production C Finisher with optional booklet unit (shown in photo) includes the punch and stapler, the
stacker tray and top exit tray, and a booklet unit capable of saddle stapling and bi -fold.
The Light Production C Finisher requires an additional electrical receptacle (see Electrical Requirements section).
32
Light Production C Finisher Product Specifications
*Cannot be offset
33
Light Production C Finisher Bi-Fold (Single Fold) Capability (available on Optional
Booklet Maker)*
Bi-Fold (Single Fold) **Capability by weight, size and paper
finish
A4 B4 A3 SRA3
8.5 x 11 8.5 x 14 11 x 17 12 x 18 (in)
Paper weight and finish (in) (in) (in)
Uncoated 60-300 g/m2 1 1 1 1 1
2
Coated 105-300 g/m 1 1 1 1 1
*Copy mode: 300 gsm coated and uncoated, image must be outside fold.
Print mode: 300 gsm uncoated (face-up).
**Bi-Fold (Single Fold): 1 sheet/set, 60-300g/m2 uncoated stock, 105-300 g/m2 coated stock
An optional Folder unit that can handle Z-fold, Tri-C, and Tri-Z, it can be added to the Light Production C
Finisher.
The C/Z folding tray can accommodate 30 sheets of up to 24 lb (90 g/m2) uncoated media.
Supported Paper size is 8.5x11 (A4) to the bottom tray, 11 x 17 (A3) to the top tray
Fold accuracy as shown below:
Z-Fold
2 mm2mm
1.0mm
1.5 mm
1/2Paper
Envelope C-Fold
1.5 mm 1.5 mm 8 mm
2 mm
34
35
Interposer for the Light Production C Finisher
The Light Production C Finisher includes a standard Interposer, used to insert pre-printed stock into finished sets without
having to go through the engine. Labels, coated media & envelopes are not supported.
Paper Size
36
Staple Capabilities by weight and paper finish for the Light Production C Finisher
Paper Size
Smallest size A4 B4 A3
203.2x254 8.5 x 11 (in) 8.5 x 14 (in) 11 x 17 (in)
Paper weight and finish (mm)
Uncoated 52-80 g/m2 100 100 100 100
81-90 g/m2 up to 100 up to 100 up to 100 up to 100
91-105 g/m2 50 50 50 50
2
106-128 g/m 30 30 30 30
2
129-150 g/m 19 19 19 19
151-176 g/m2 12 12 12 12
2
177-220 g/m 5 5 5 5
2
221-256 g/m 4 4 4 4
2
256-300 g/m 3 3 3 3
Coated 106-128 g/m2 5 5 5 5
2
129-150 g/m 5 5 5 5
2
151-176 g/m 5 5 5 5
2
177-220 g/m 5 5 5 5
221-256 g/m2 4 4 4 4
2
256-300 g/m 3 3 3 3
37
Optional Booklet Maker for the Light Production C Finisher*
Sheets per Booklet by weight, size and paper finish
Paper Size
A4 B4 A3 SRA3
Paper weight and finish 8.5 x 11 8.5 x 14 11 x 17 12 x 18
(in) (in) (in) (in)
Uncoated 60-80 g/m2 25 25 25 25 25
2
81-90 g/m 20 20 20 20 20
2
91-105 g/m 10 10 10 10 10
2
106-128 g/m 10 10 10 10 10
129-150 g/m2 10 10 10 10 10
2
151-176 g/m 10 10 10 10 10
2
177-220 g/m 5 5 5 5 5
2
221-256 g/m 4 4 4 4 4
256-300 g/m2 3 3 3 3 3
2
Coated 106-128 g/m 10 10 10 10 10
2
129-150 g/m 10 10 10 10 10
2
151-176 g/m 10 10 10 10 10
177-220 g/m2 5 5 5 5 5
38
Light Production C Finisher Product Caveats/Limitations
If the compiler tamper arm resets itself during a job, the job will need to be re-submitted
If hole punching fails, check to make sure that the punch waste container is empty before calling service
After cancelling a job sent to the Booklet maker, empty the purge tray (located inside the Light Production
C Finisher) before submitting another print job. This will ensure that purged sheets are not inadvertently
inserted into the next booklet printed.
Combined finishing (attaching a HCS and Light Production C Finisher together in a system) is available with
external Print Servers only.
Attaching a HCS and Light Production C Finisher together in a system with the Integrated Print Server will
result in all jobs being sent unfinished to the top tray of the HCS until the second finisher is detached from
the system, and the system is rebooted. This will require a service call.
A reduction in productivity may be experienced when sending duplexed 11 x 17 stock to the stacker tray.
The machine will pause for xerographic adjustment when necessary. This will impact productivity.
Requires an additional electrical receptacle (see Electrical Requirements section).
39
GBC Advanced Punch
The GBC AdvancedPunch is an inline die punch that utilizes modular die sets to enable a variety of hole-punch
patterns in A4/8 x 11 in (LTR) long-edge-fed media.
For use with HCS or Light Production C Finisher not available for use on Advanced or Professional
Finishers, or with the Offset Catch Tray
The GBC Advanced Punch can be added to an existing Light Production C Finisher or HCS through an
available upgrade kit
The GBC Advanced Punch requires an Interface Module (IFM) with updated software and hardware
Supported by all color servers
Supports media from 80 to 216 gm2, coated and uncoated
ProClick die supports media from 80 to 203 gm2
Able to bypass all coated and uncoated media sizes printed on the Xerox 700 Digital Color Printer
A4 and LTR punch units are not the same; therefore, A4 and LTR die sets are not interchangeable.
The LTR punch unit will be shipped with the 19-hole punch die.
The A4 unit will ship with the 21-hole punch die.
Additional punch dies are available for order (see below)
Punch Dies
The GBC Advanced Punch is capable of punching a variety of hole-punch patterns by simply changing the
punch die. Punch dies can be changed in seconds without tools. The punch dies currently available are listed
below.
Please note: Punch die life will be increased if the wick material is lightly oiled every 50K punch cycles
(approximately every month) with quality machine oil such as 3-in-I Oil. Small deposits of oil will be observed
around the perimeter of the punched holes until the excess oil is absorbed (usually within 50 sheets).
40
41
SquareFold Trimmer Module
Overview
The SquareFold Trimmer Module is an optional piece of equipment that flattens the spine of the booklet to
make it lay flat and trims the face of the booklet. It requires the Light Production C Finisher with Booklet Maker
(with or without the C-Z Folder) that has upgraded software and hardware. The SquareFold Trimmer Module
is a fully-integrated device, controlled through the print engine UI.
The SquareFold Trimmer Module can be added to an existing Light Production C Finisher through an available
upgrade kit.
Configuration
The SquareFold Trimmer Module is located after the Light Production C Finisher and performs as follows:
receives the booklet from the booklet unit
transports the received booklet to the square fold unit to flatten the spine of the booklet and then to the
trimmer unit to trim the face of the booklet
deposits the finished booklet to the booklet tray.
The SquareFold Trimmer Module is also able to face-trim without square-folding
All output from the Light Production C Finisher can be passed through, square-folded, trimmed, or both
squared-folded and trimmed
When the SquareFold Trimmer Module is docked to the Light Production C Finisher via cable, the finisher
automatically recognizes that the SquareFold Trimmer Module is installed.
Square-folding feature: flattens the spine (stapled side) of the booklet.
Trimming feature: trims the face of the saddle-stapled or bi-folded (single-folded) sheets of paper.
42
Combination of Output Functions and Destinations
Trimmer Booklet
Booklet Tray
Square Fold
Trimmer
Booklet
Tray
Offset X X X X X
Staple X X X X X
Punch X X X X X
Interposer O O O O O
Booklet - O O* O O
Z-Fold X X X X X
Function
C- Fold X X X X X
Bi-Fold (Single Fold) - O O* O O
Staple + Punch X X X X X
Staple + Z-Fold X X X X X
Staple + Interposer X X X X X
Function + Function
Punch + Z-Fold X X X X X
Z-Fold + Interposer X X X X X
Staple + Punch + Z-Fold X X X X X
Staple + Punch + Z-Fold
X X X X X
+ Interposer
* Square-folding/trimming of non-stapled sets and square-folding of 4 or less sheets in a set are outside the specification
and are therefore not guaranteed (jams may occur frequently or wrinkles may occur on the square-folded side of paper).
43
Combining High Capacity Stacker and the Light Production C Finisher
The Xerox 700 Digital Color Press will allow installation of both a High Capacity Stacker and a Light Production
C Finisher in a single system. It will not be possible to install 2 High Capacity Stackers on the Xerox 700 Digital
Color Press.
An upgrade kit will be required to add the second finisher to existing installations.
The High Capacity Stacker and the Light Production C Finisher can be installed at the same time on any system
using any of the available external Print Servers:
Please note: The High Capacity Stacker and the Light Production C Finisher cannot be installed at the same time
on any system using the Integrated Fiery Color Server. If both finishers are detected, the following error
message will be printed to the top tray of the HCS:
The Xerox 700 Digital Color Press with Integrated Fiery Color Server does not
support the current configuration of installable options.
The High Capacity Stacker and the Light Production C Finisher cannot be
installed at the same time.
All jobs will be sent unfinished to the top tray of the HCS until the second finisher is detached from the system,
and the system is rebooted. This will require a service call.
44
Supported Configurations
The following sketches show the supported configurations for the Xerox 700 Digital Color Press:
Configuration 1
SquareFold
1- or 2- Tray OHCF Trimmer Module
IOT
Configuration 2 Not available with Integrated Fiery Color Server Light Production C Finisher with or
without Booklet Maker, with or
without C-Z Fold
1- or 2- Tray
OHCF IFM HCS
Configuration 3 Not available with Integrated Fiery Color Server Light Production C Finisher with Booklet Maker,
with or without C-Z Fold
IOT
1- or 2- Tray OHCF IFM HCS
SquareFold Trimmer
Module
45
Configuration 4
IOT GBC
1- or 2- Tray OHCF IFM Advanced HCS
Punch
Configuration 6
SquareFold
Trimmer Module
46
Configuration 7 Not available with Not available with Integrated Fiery Color Server
Light Production C Finisher
with or without Booklet Maker,
1- or 2 Tray IOT GBC with or without C-Z Fold
OHCF Advanced HCS
IFM
Punch
Configuration 8 Not available with Not available with Integrated Fiery Color Server
Light Production C Finisher with Booklet
GBC Maker, with or without C-Z Fold
1- or 2 Tray IOT Advanced
OHCF IFM Punch HCS
SquareFold
Trimmer
Module
47
Customer Agreement
Reference Material
Xerox 700 Digital Color Press is shipped with a complete set of user guides on a CD ROM.
Customer Support
The Xerox Customer Support Centers are available to provide general information, answer questions and take
service calls.
You can reach the Customer Support Center at the following phone numbers:
United States: 1-800-821-2797 (toll-free)
Canada :1-800-939-3769 (toll-free)
Xerox Europe (Local Numbers):
48
Customer Training
Customer training on machine features and functions is a purchasable service for the Xerox 700 Digital Color
Press.
Responsibility Matrix:
49
Customer Expectations Agreement
Check off the modules that will be part of this install and for which expectations have been set:
_____ Xerox 700 Digital Color Press _____ Optional High Capacity Feeder
_____ Optional Oversized High Capacity Feeder (1- _____ Optional Interface Module (IFM)
or 2- Tray)
_____ Optional Advanced Finisher _____ Optional Professional Finisher with Booklet
Maker
_____ Optional Light Production C Finisher (LPC _____ Optional Light Production C Finisher (LPC
Finisher) Finisher) with Booklet Make
_____ Optional CZ Folder (CZ Folder) _____ Optional High Capacity Stacker (HCS)
_____ Xerox FreeFlow Print Server for the Xerox _____ Xerox CX Print Server, Powered by Creo for
700 the Xerox 700
_____ Xerox EX Print Server, Powered by Fiery for _____ Integrated Fiery Color Server
the Xerox 700
_____ EFI Splash RPX-iii Color Workflow Software (Requires passing data through the Xerox EX Print Server or
Integrated Fiery Color Server
50
Please note: A separate CED must be filled out and signed for the print server.
I have reviewed and understand the product specifications for each of the modules
that will be installed: (signatures required)
Customer
I have viewed a representative output sample from the Xerox ____________ Press and the image quality is
acceptable for the needs of my organization:
(Signature required if Xerox Digital Press with order.)
Customer
This page intentionally left blank
52