Documente Academic
Documente Profesional
Documente Cultură
LIST OF EXPERIMENTS
1. Characteristics of Semiconductor diodes and zener diode
2. Characteristics of NPN Transistor under CE &CB configuration
3. Characteristics of JFET
4. Characteristics of UJT
5. Design and frequency response characteristics of a CE Amplifier
6. Design and Testing of Rc Phase shift
7. Single Phase Half wave and full wave Rectifier with and without filter
8. Charecteristics of Photo diode
9. Differential Amplifier using Fet
10. Study of CRO for Frequency and Phase shift
TOTAL: 45 PERIODS
2. Construct a circuit to determine the VI characteristics of Zener diode. Plot the graph and
determine the Breakdown voltage and the dynamic resistance of the diode
5. Constuct a circuit to determine the input and output characteristics of BJT common emitter
configuration
6. Construct a circuit to determine the input and output characteristics of BJT common base
Configuration
7. Construct a differential amplifier using FET determine the Common mode gain anddifferential
mode gain and hence CMRR
8. Construct a circuit to determine the VI characteristics of UJT. Plot the graph and determine the
intrinsic standoff ratio
10. Construct a circuit to determine the frequency response of a common emitter amplifier
11. Construct a circuit to determine the VI characteristics of Photodiode. Plot the graph
12.Construct a Half wave Rectifier with capacitor filter observe the waveform and calculate the
ripple factor
13. Construct a full wave Rectifier with capacitor filter observe the waveform and calculate the
ripple factor.
14. Conduct a suitable experiment to obtain the dc output using half wave rectifier without filter.
15.conduct a suitable experiment to obtain ripple free dc output for one half of ac input.
17. Illustrate how CRO can be use to determine the frequency and phase angle of an input signal.
1. Construct a circuit to determine the VI characteristics of PN junction diode. Plot the graph and
determine the Knee voltage and the dynamic resistance of the diode
AIM(5 CIRCUIT PROCEDURE(10 OBSERVATION & GRAPH & VIVA
) DIAGRAM(25 ) TABULATION(40) RESULT(10) VOCE(10)
)
2. Construct a circuit to determine the VI characteristics of Zener diode. Plot the graph and
determine the Breakdown voltage and the dynamic resistance of the diode
AIM(5 CIRCUIT PROCEDURE(10 OBSERVATION & GRAPH & VIVA
) DIAGRAM(25 ) TABULATION(40) RESULT(10) VOCE(10)
)
6. Construct a circuit to determine the input and output characteristics of BJT common base
Configuration
AIM(5 CIRCUIT PROCEDURE(10 OBSERVATION & GRAPH & VIVA
) DIAGRAM(25 ) TABULATION(40) RESULT(10) VOCE(10)
)
7. Construct a differential amplifier using FET determine the Common mode gain and differential
mode gain and hence CMRR
AIM(5 CIRCUIT PROCEDURE(10 OBSERVATION & GRAPH & VIVA
) DIAGRAM(25 ) TABULATION(40) RESULT(10) VOCE(10)
)
8. Construct a circuit to determine the VI characteristics of UJT. Plot the graph and determine the
intrinsic standoff ratio
AIM(5 CIRCUIT PROCEDURE(10 OBSERVATION & GRAPH & VIVA
) DIAGRAM(25 ) TABULATION(40) RESULT(10) VOCE(10)
)
10. Construct a circuit to determine the frequency response of a common emitter amplifier
AIM(5 CIRCUIT PROCEDURE(10 OBSERVATION & GRAPH & VIVA
) DIAGRAM(25 ) TABULATION(40) RESULT(10) VOCE(10)
)
11. Construct a circuit to determine the VI characteristics of Photodiode. Plot the graph
AIM(5 CIRCUIT PROCEDURE(10 OBSERVATION & GRAPH & VIVA
) DIAGRAM(25 ) TABULATION(40) RESULT(10) VOCE(10)
)
12. Construct a Half wave Rectifier with capacitor filter observe the waveform and calculate the
ripple factor
13. Construct a full wave Rectifier with capacitor filter observe the waveform and calculate the
ripple factor.
AIM(5 CIRCUIT PROCEDURE(10 OBSERVATION & GRAPH & VIVA
) DIAGRAM(25 ) TABULATION(40) RESULT(10) VOCE(10)
)
14. Conduct a suitable experiment to obtain the dc output using half wave rectifier without filter.
15. Conduct a suitable experiment to obtain ripple free dc output for one half of ac input.