Documente Academic
Documente Profesional
Documente Cultură
ADJUSTMENT
1. VEHICLE PREPARATION FOR HEADLIGHT AIM
ADJUSTMENT
(a) Prepare the vehicle:
Ensure there is no damage or deformation to the
body around the headlights.
Fill the fuel tank.
Make sure that the oil is filled to the specified
level.
Make sure that the coolant is filled to the
specified level.
Inflate the tires to the appropriate pressure.
Place the spare tire, tools, and jack in their
LI original position.
Unload the trunk.
Seat a person of average weight (68 kg, 150 lb)
in the driver's seat.
2. PREPARATION FOR HEADLIGHT AIMING (Using a
tester)
(a) Prepare the vehicle for headlight aim check.
(b) Adjust in accordance with headlight tester
instructions.
3. PREPARATION FOR HEADLIGHT AIMING (Using a
screen)
(a) Prepare the vehicle according to the following
conditions:
Place the vehicle in a location that is dark
90 enough to clearly observe the cutoff line. The
cutoff line is a distinct line, below which light from
the headlights can be observed and above which
7.62 m (25 ft.) it cannot.
I043700E01 Place the vehicle at a 90 angle to the wall.
Create a 7.62 m (25 ft.) distance between the
vehicle (headlight bulb center) and the wall.
Place the vehicle on a level surface.
Bounce the vehicle up and down to settle the
suspension.
NOTICE:
A distance of 7.62 m (25 ft.) between the vehicle
and the wall is necessary for proper aim
adjustment. If unavailable, secure a distance of
exactly 3 m (9.84 ft.) for check and adjustment.
(The target zone will change with the distance so
follow the instructions in the illustration.)
(b) Prepare a piece of thick white paper (approximately
2 m (6.6 ft.) (height) x 4 m (13.1 ft.) (width)) to use
as a screen.
(c) Draw a vertical line down the center of screen (V
line).
(d) Set the screen as shown in the illustration.
HINT:
Stand the screen perpendicular to the ground.
LIGHTING HEADLIGHT ASSEMBLY LI13
V RH Line V RH Line
90 90
V Line V Line
7.62 m (25 ft.) 3 m (9.84 ft.)
V LH Line V LH Line
LI
H Line H Line
90 90
I042055E01
HINT:
Alignment distance is 7.62 m (25 ft.):
The cutoff line is 101 mm (3.97 in.) above and
below the H line as well as left and right of the V
line with low-beam (SAE J599).
Alignment distance is 3 m (9.84 ft.):
LIGHTING HEADLIGHT ASSEMBLY LI15
INSTALLATION INSTRUCTIONS
WARNING
There are several WARNING and CAUTION sections in this booklet concerning
safety when installing or removing the rear spoiler. Always read and follow them in
order to prevent injuries, accidents, and possible damage to the vehicle.
WARNING: Indicates a situation in which serious injury or death could result if
the warning is ignored.
CAUTION : Indicates a situation in which bodily injury or damage to the vehicle
could result if the caution is ignored.
Do not modify the fog light bezel.
Do not install the fog light bezel in any way other than described in the following
instructions.
If in any doubt, please ask your Mazda dealer to install the accessory in order to
prevent errors in installation.
If you have any questions about the use of the accessory, ask your Mazda dealer for
proper advice before using it.
Mazda and its suppliers are not responsible for injuries, accidents, and damage to
persons and property that arise from the failure of the dealer or installer to follow these
instructions.
To ensure safety and reliability of the work, installation, removal and disposal work
must carried out by an Authorized Mazda Dealership.
Be careful not to lose removed parts, and be sure that they are kept free from
scratches, grease or other dirt.
0000 00 000
PARTS
Parts list
NOTE
Before installation, verify that the kit includes all the following parts and that they are free of dirt, scratches,
or damage.
Installation instructions 1
Installation instructions 1
CAUTION
Fog lights are not included in this kit. For vehicles without fog lights, it is necessary to purchase them
separately.
Separate purchase
GENUINE FOG LIGHT N121 V7 220 N122 V7 220 N123 V7 220
Clear Blue Multi coating
Installation view
REQUIRED TOOLS
Screwdriver (Phillips) Torque wrench Fastener remover Round file
BEFORE INSTALLATION
WARNING
When the negative battery cable is Do not pull the harness When connecting/disconnecting
connected during operation, it may With excessive force. Doing so connectors, grasp the
cause electric shock or other can cause a breakage or a connectors, not the wires.
personal injuries. Disconnect the short-related accident, as well as Otherwise a short, an accident
negative battery cable before an electrical short or fire. from poor contact or fire may
removal/installation. occur.
CAUTION
Be sure to cover the vehicle body Use the most appropriate Place the removed parts and kit
With protectors or mats to prevent (size, use) tool for each task and accessories on a protective sheet
stains, scratches and damage when perform the may be damaged. to prevent scratches.
removing/installing the vehicle parts
WARNING
Park the vehicle on a flat, level surface, set the selector lever to P (AT vehicles) or the shift lever to 1st or R
(MT vehicles), apply the parking brake and block the wheels so that the vehicle does not move during
CAUTION
When the negative battery cable is removed, the clock, radio, trip, meters and other memories will be
erased. Before performing work, record the content of the memory.
Always tighten bolts, nuts and screws with a torque wrench, and tighten to the specified torque. If tightened
outside the specified torque, it could result in poor fit, damage to installed parts or other damage.
NOTE
Refer to the Workshop Manual for removal and installation of vehicle parts.
Not following the procedures for removal/installation in the Workshop Manual could result in an accident or
vehicle malfunction.
PART REMOVAL
Tab NOTE
The figure shows the right side, however, perform the
same procedure for the left side.
Hole cover
CAUTION
The removed fog light bezel are not used to install this
Screw accessory.
The removed fog light, bolt (1) and screws (2) are to
be reused. Be careful not to damage or lose them.
Fog light bezel
Adjusting
Tab bolt NOTE
Fog light bezel The figure shows the right side, however, perform the
same procedure for the left side.
Cross section
FOG LIGHT INSTALLATION
NOTE
The figure shows the right side, however, perform the same procedure for the left side.
CAUTION
Be careful not to scratch the surface of the fog light bezel.
Round file
CAUTION
Only partially tighten the fog light adjusting bolt at this point
in the procedure, as it will be completely tightened after
completing the aiming adjustment.
Screw
Adjusting bolt
Secure the fog light bezel to the front bumper using the
Front bumper
Screw screws (2) and the tabs (3 locations).
Tightening torque
Screw0.31.5 Nm {3.015.0 kgfcm2.6 13.2 inlbf }
CAUTION
Tighten the screw securely
Make sure to tighten to the specified torque. If tightened
Screw
outside the specified torque, the front fog light bezel or
front bumper could be damaged or fall off.
PART INSTALLATION
Front bumper installation
Peel off the tape wrapped around the vehicle wiring harness.
(When installing fog lights on a vehicle not equipped with fog lights)
Fog light equipped vehicles, Connect the fog light wiring harness connector to the fog light.
or separately purchased fog light
Front bumper CAUTION
Make sure that the fog light wiring harness connector is
securely inserted until it locks.
Bolt A2 Locations
Tightening torque7.811.8 Nm
{80.0120.0 kgfcm70.0 104.0 inlbf }
B
Bolt A A
CAUTION
Cover Front bumper After completing the aiming adjustment, install fastener A
and screw A.
Tighten the bolt and nut securely
Make sure to tighten to the specified torque. If tightened
outside the specified torque, the front bumper could be
damaged or fall off.
OPERATION CHECK
Disconnect the negative battery cable
WARNING
Before starting the engine, make sure nobody is in front or back of the vehicle, or in the engine compartment. If
the vehicle were to move suddenly it could cause a serious accident.
Do not start the engine in a place such as a garage or other location with poor air ventilation. Otherwise,
poisoning or asphyxiation could result from accumulation of exhaust gas.
CAUTION
Disconnecting the battery causes the DSC indicator light to become inoperable.
At this point, the DSC OFF indicator light flashes and the TCS/DSC indicator light is illuminated.
To restore the DSC to an operable condition, perform the following procedures:
Turn the ignition switch to the ON position.
Turn the steering wheel completely to the right and then completely to the left.
Verify that the DSC OFF indicator light goes out.
Turn the ignition switch off and then turn it to the ON position again.
Verify that the TCS/DSC indicator light goes out.
If the TCS/DSC or DSC OFF indicator lights do not go out after turning the ignition switch to the ON
position, consult your Mazda dealer.
When the battery is disconnected, the windows will not fully open and close automatically.
Perform the following procedure to resume operation:
Turn the ignition switch to the ON position.
Press the switch and fully open the window.
Pull up the switch and continue holding for about 2 seconds to fully close the window.
Tightening torque
Upward Adjusting bolt1.03.4 Nm
{10.034.0 kgfcm8.9 30.0 inlbf }
INSTALLATION
MX-5 FOG LIGHT BEZEL
INSPECTION
SHEET N121 V7 247FSILVER
N123 V7 247FBLACK
Checked
charge
ADJUSTMENT
1. VEHICLE PREPARATION FOR FOG LAMP AIM ADJUSTMENT
(a) Prepare the vehicle:
Ensure that there is no damage or deformation to the body around the fog lamps.
Fill the fuel tank.
Make sure that the oil is filled to the specified level.
Make sure that the coolant is filled to the specified level.
Inflate the tires to the appropriate pressure.
Place the spare tire, tools, and jack in their original positions.
Unload the trunk.
Sit a person of average weight (68 kg, 150 lb) in the driver seat.
V RH Line V RH Line
90 90
V Line V Line
7.62 m (25 ft) 3 m (9.84 ft)
V LH Line V LH Line
H Line H Line
90 90
E76103
H Line H Line
I41221