Documente Academic
Documente Profesional
Documente Cultură
Shell ID 635
Shell THK 20 No. 24
BOLT M 24 No. 41.0814 Max.
B 58.74
Rh 36.51
E 28.58
Root Area 312.748
Gasket Moc HE-CGI, HE-CG, Spiral Wound gaskets for heat exchangers
m 3
y 703
BODY FLANGE
DESIGN DATA
Outside diameter of flange A 825 mm
Inside diameter of flange(corroded) B 635 mm
Bolt-circle diamter C 768 mm
Number of bolt n 24 set
Size of bolt Db 24 mm
Cross section area per a bolt Ar 312.75 mm2
Outside diameter of gasket do 732 mm
Width of gasket used to determine the basic gasket seating
N 20 mm
Thickness of gasket Tg 4.5 mm
Thickness of hub at small end go 20 mm
Thickness of hub at back of flange g1 30.0 mm
Tub length h 40.0 mm
Corrosion allowance CA 0 mm
Intermal design pressure P 55 Kg/cm2G
Flange thickness t 120 mm
MATERIAL SPECIFICATION
FLANGE: SA182 F316L
Max. allowable stress at design temprtature Sfb 1111 Kg/cm2
Max. allowable stress at atm temprtature Sfa 1173 Kg/cm2
Gasket : HE-CGI, HE-CG, Spiral Wound gaskets for heat exch
Gasket or joint contact-surface unit seating load y 7.03 Kg/cm2
Gasket factor m 3
BOLT: SA193 Gr.B8 M20 to M24
Allowable bolt stress at design temperature Sb 1406.1 Kg/cm2
Allowable bolt stress at atm temperature Sa 1406.1 Kg/cm2
CALCULATION
1.FACTOR
Ratio of outside diameter of alange to inside diamet K 1.299
Factor involvig K T 1.798
U 8.305
Y 7.557
Z 3.904
Factor ho=(Bgo) 0.5
ho 112.694 mm
g1 /go= 0.000
h / ho= 0.000
Factor for intergraltype flages ,V V 0.350
Factor for intergraltype flages ,F F 0.865
Hub stress corrosion factor integral type flanges , f f 1.000
Factor d,d=(u/v)hogo2 d ### mm3
Factor e,e=F/ho e 0.008 1/mm
Factor L,L=(te+1)/T+t /d 3
L 2.684
2.BOLT LOADS(CNS9791-3.3)-
Basic gasket seating width , bo=N/2 bo 10.00 mm
Effective gasket or joint conta b 7.97 mm
b=0.5(bo) for bo>6.35mm(0.25in) or b=bo
0.5
? for bo<=6.35mm7.97
Diameter at location of gasket load reaction G 716.08 mm
Min required bolt load for the operating conditions Wm1 ### Kg
Wm1=0.785G P+2b3.14159mP
2
HT=H- HT 47211.12 Kg
Gasket load HG= HG 59159.82 Kg
3.1For intergral flange
Radial distance from BCD to point of intersection of
R=(C-B)/2-g1 R 36.510 mm
Radial distance from the bolt circle t Hd 51.510 mm
Radial distance from the bolt circle Ht 46.239 mm
Radial distance from gasket load reaction to the bolt Hg 25.969 mm
Component of moment due to MD ### kg-mm
Component of moment due to MG ### kg-mm
Component of moment due to MT ### kg-mm
Total flange moment for the operating conditions Mo=MD+MG+MT Mo ### kg-mm
3.2For gasket seating
Total cross-sectional area of bolts at root of thread required for the operting conditions Am1 19952.3 mm2
Total cross-sectional area of bolts at root of thread required for gaster seating Am2 8963.0 mm2
Total required cross-sectional area Am 19952.3 mm2
Cross-section area of the bolts using the root diametAb 7506.0 mm2
Flang design bolt load , Wg=(Am+Ab)Sa/2 W g 193045.5 kg
Total flange moment for gasket seating , Mg=Wg(C-G)/2 Mg ### kg-mm
4.CALCULATION OF FLAGE STRESSES(CNS9791-3.5)
Longitudinal hub stress ,SH=fMo/(Lg12B) SH1 827.295 Kg/cm2
Longitudinal hub stress ,SH=fMg/(Lg1 B)
2
SH2 326.790 Kg/cm2
Radial flange stress ,SR=(1.33te+1)Mo/(Lt2SR1
B) 115.047 Kg/cm2
Radial flange stress ,SR=(1.33te+1)Mg/(Lt SR2
2
B) 45.445 Kg/cm2
Tangential flange stress ,ST=YMo/(t2B)-ZSR1 ST1 (449.047) Kg/cm2
Tangential flange stress ,ST=YMg/(t2B)-ZSR2 ST2 (34.830) Kg/cm2
5.CHECKED CODITIONS(CNS9791-3.6)
SH is mot gre SH= ### < *Sf= 2109.15 Kg/cm2
SR is not grea SR= ### < Sf= 1406.1 Kg/cm2
ST is not grea ST= ### < Sf= 1406.1 Kg/cm2
(SH+SR)/2 is = ### < Sf= 1406.1 Kg/cm2
(SH+ST)/2 is = ### < Sf= 1406.1 Kg/cm2
#ALL CONDITIONS ARE SATISFACTORY#
6.MIX. USED THICKNEES OF FLANGE
The required for the not operting conditions t1 t1 71.32 mm
The required for the operting conditions t2 t2 116.60 mm
Design thickness of flange ,Tm=Mix.{t1,t2}+CA Tm 116.60 mm
ickness of flange is 117 mm.
l thickness used of 120 mm. #SUFFICIENT#
NOTE
BY : PRADEEP NAYAK FROM DOMBIVLI, INDIA VISIT http://www.pvtools.weebly.com/
t= 120 h= 40.0
B Rh
E= 28.6 12 31.8 21
16 44.5 29
20 52.4 32
R = 36.5 22 54 33
24 58.7 37
27 63.5 38.1
20
g1= 30.0 30 73 46
36 84.1 54
825
768
732
42 100 62
g0= 20.0 48 113 68
ID = 635
RF =
C=
A=
mm
mm
mm Maximum Allowable Stress, Kg/cm for Metal Temperature, C
set -30 to 4065 ###### 150 ### 250 300 325 350 375 400 425 450
mm SA3 ### ######### 1407 ### 1407 1407 1407 ### ### ### 1397 ###
mm 2
SA3######
###
############ ### 1061 ###### 909 769 638
mm SA1 ### ######### 1173 ### 1050 999 976 960 946 927 908 895
mm SA1 ### ######### 1366 ### 1285 1213 1183 ### ### ### 1122 1101
mm SA1 ### ######### 1173 ### 1050 996 977 960 947 934 915 901
mm SA1 ### ######### 1050 ### 917 876 858 838 821 808 788 775
mm SA2######
###
############ ### 1061 ###### 909 769 638
mm SA2 ### ######### 1407 ### 1387 1315 1275 ### ### ### 856 683
mm SA ### ######### 1407 ### 1387 1315 1275 ### ### ### 856 683
Kg/cm2G
mm
Kg/cm2
Kg/cm2
Kg/cm2
Kg/cm2
Kg/cm2
mm
mm3
1/mm
mm
mm
mm
Kg
Kg
Kg
Kg
Kg
Kg
mm
mm
mm
mm
kg-mm
kg-mm
kg-mm
kg-mm
mm2
mm2
mm2
mm2
kg-mm
Kg/cm2
Kg/cm2
Kg/cm2
Kg/cm2
Kg/cm2
Kg/cm2
Kg/cm2
Kg/cm2
Kg/cm2
Kg/cm2
Kg/cm2
mm
mm
mm
Self energ 0 0
Elastomer 0.5 0
Elastomer 1 14.06139
Mineral f 2 112.4911
Mineral f 2.75 260.1358
Mineral f 3.75 456.9952
Elastomer 1.25 28.12278
Elastomer 2.25 154.6753
Elastomer 2.5 203.8902
Elastomer 2.75 260.1358
Vegetable 1.75 77.33766
Spiral wo 2.5 703.0696
Spiral wo 3 703.0696
Corrugate 2.5 203.8902
Corrugate 2.75 260.1358
Corrugate 3 316.3813
Corrugate 3.25 386.6883
Corrugate 3.5 456.9952
Corrugat 2.75 260.1358
Corrugate 3 316.3813
Corrugate 3.25 386.6883
Corrugat 3.5 456.9952
Corrugate 3.75 534.3329
Flat meta 3.25 386.6883
Flat meta 3.5 456.9952
Flat metal 3.75 534.3329
Flat meta 3.5 562.4557
Flat meta 3.75 632.7626
Flat meta 3.75 632.7626
Grooved 3.25 386.6883
Grooved m 3.5 456.9952
Grooved m 3.75 534.3329
Grooved 3.75 632.7626
Grooved m 4.25 710.1003
Solid fla 4 618.7012
Solid fla 4.75 913.9905
Solid flat 5.5 1265.525
Solid fla 6 1532.692
Solid fla 6.5 1827.981
Ring Joint 5.5 1265.525
Ring Joi 6 1532.692
Ring Join 6.5 1827.981
PTFE 2 201
HE-CGI, HE 3 703
E Root Area
15.88 72.398
20.64 138.324
23.81 217.051 SA193 Gr.7 Upto M65
25.4 272.419 SA193 Gr.B8 Upto M20
28.58 312.748 SA193 Gr.B8 M20 to M24
29 413.852 SA193 Gr.B8M Upto M20
33.34 502.965 SA193 Gr.B8M M20 to M24
39.69 738.015
49.21 1018.218
55.56 1342.959
mperature, C
475 500
1091 694
464 322
883 -
1101 1091
- -
763 751
464 322
521 343
521 343
m
1757.7
1757.7
1406.1
1546.8
1406.1
10000 3
10000 3
10000 3
10000 3
10000 3
10000 3
5000 3
4200 3
10000 3
2500 2
10000 3
2500 2
1885 1.4
2320 1.4
1885 1.4
2320 1.4
1595 1.4
1885 1.4
1595 1.4
2900 3.2
2900 3.2
3335 3.7
3335 3.7
3335 3.7
900 2
900 2
2500 2
2500 2
2500 2
2500 2
2500 2
18000 5.5
21800 6
26000 6.5
10000 3
5000 3
5000 3
3700 2.75
3700 2.75
3700 2.75
3700 2.75
3700 2.75
2500 2.75
900 2
2500 2
2500 4
1800 4
3500 7
5000 10
7000 24
4500 6
3000 4.5
4000 7
3050 4.2
4400 5.2
2100 3.5
3000 6.6
3050 2.1
3500 4
2800 3.5
4200 6.7
2500 8.1
2300 7.4
2000 2
1800 1.5
3600 1.5
2600 6.6
3300 6.6
2400 3.5
3900 5.5
2350 3.5
3200 8
2550 6.5
2800 8
4100 4.5
4100 6
4800 11.4
6500 22
2750 5
3500 5
1650 3
3000 2.5
2350 2
2500 2
1650 2.8
1600 2
1700 3
2200 3
2200 2
2500 2
1500 2.6
2200 2
2200 2
3700 7
800 2
1400 2.8
2300 3.7
2800 5.5
2800 6
3500 5
4000 5
3500 5
4000 5
1650 3
2500 3
1500 3
1700 3
y --- ASME ----
Self energizing type (O rings, elastomers etc.)
Elastomer without fabric or high % of mineral fiber < 75A Shore Durometer
Elastomer without fabric or high % of mineral fiber > 75A Shore Durometer
Mineral fiber with suitable binder (CAF) 1/8 inch
Mineral fiber with suitable binder (CAF) 1/16 inch
Mineral fiber with suitable binder (CAF) 1/32 inch
Elastomers with cotton fabric insertion
Elastomers with fiber fabric insertion 3-ply
Elastomers with fiber fabric insertion 2-ply
Elastomers with fiber fabric insertion 1-ply
Vegetable fiber
Spiral wound metal, fiber filled: Carbon
Spiral wound metal, Monel and Nickel-base alloys
Corrugated metal, fiber inserted, or corr. (MJAF) Soft Aluminum
Corrugated metal, fiber inserted, or corr. (MJAF) Soft Copper or Brass
Corrugated metal, fiber inserted, or corr. (MJAF) Iron of Soft Steel
Corrugated metal, fiber inserted, or corr. (MJAF) Monel of 4%-6% chrome
Corrugated metal, fiber inserted, or corr. (MJAF) S/S and Nickel-base
Corrugated metal: Soft Aluminum
Corrugated metal: Soft copper or brass
Corrugated metal: Iron or soft steel
Corrugated metal: Monel or 4%-6% chrome
Corrugated metal: S/S and nickel-base
Flat metal, jacketed mineral fiber filled: Soft Aluminum
Flat metal, jacketed mineral fiber filled: Soft copper or brass
Flat metal, jacketed mineral fiber filled: Iron or soft steel
Flat metal, jacketed mineral fiber filled: Monel
Flat metal, jacketed mineral fiber filled: 4%-6% chrome
Flat metal, jacketed mineral fiber filled: S/S and nickel-base
Grooved metal: Soft Aluminum
Grooved metal: Soft copper or brass
Grooved metal: Iron or soft steel
Grooved metal: Monel or 4%-6% chrome
Grooved metal: S/S and nickel-base
Solid flat metal: Soft Aluminum
Solid flat metal: Soft copper or brass
Solid flat metal: Iron or soft steel
Solid flat metal: Monel or 4%-6% chrome
Solid flat metal: S/S and nickel-base
Ring Joint: Iron or soft steel
Ring Joint: Monel or 4%-6% chrome
Ring Joint: S/S and nickel-base
PTFE
HE-CGI, HE-CG, Spiral Wound gaskets for heat exchangers
---- Flexitallic Gasket Factors -----
703.0696 CG, CGI, R, RIR, Spiral Wound gaskets
703.0696 CG-RJ, CGI-RJ, Spiral Wound Ring gaskets
703.0696 HE-CGI, HE-CG, Spiral Wound gaskets for heat exchangers
703.0696 Spiral Wound Styles M, MC and MCS for Boiler Manhole Assemblies
703.0696 Spiral Wound Style T for Boiler handhole and Tubecap Assemblies
703.0696 Baker gasket for HF Acid & Hazardous Chemical applications
351.5348 LS, LSI, Spiral Wound Low Stress gaskets
295.289232 Thermiculite 715: Coreless sheet, 1/16in thick (high temperature applications
703.0696 Thermiculite 735: Spiral Wound filler (high temperature)
175.7674 Thermiculite 815: Tanged sheet, 1/16in thick (high temperature applications)
703.0696 Thermiculite 835: Spiral Wound filler (high temperature)
175.7674 Thermiculite 845: Flexpro (Kammprofile) facing (high temperature)
132.5286196 Sigma 500, PTFE gasket: PTFE, Glass Microspheres 1/32in thick
163.1121472 Sigma 511, PTFE gasket: PTFE, Silica 1/32in thick
132.5286196 Sigma 522, PTFE gasket: PTFE, Barium Sulfate 1/16in thick
163.1121472 Sigma 533, PTFE gasket: PTFE, Barium Sulfate 1/32in thick.
112.1396012 Sigma 588, PTFE gasket: PTFE 1/16in thick.
132.5286196 Sigma 599, PTFE gasket: PTFE, Glass Microspheres 1/16in thick
112.1396012 Sigma 600, PTFE gasket: PTFE 1/32 - 1/4in thick
203.890184 SF 2401, Compressed Fiber Sheet gaskets: Synthetic, NBR
203.890184 SF 2420, Compressed Fiber Sheet gaskets: Synthetic, SBR
234.4737116 SF 3300, Compressed Fiber Sheet gaskets: Aramid, Glass, NBR
234.4737116 SF 3500, Compressed Fiber Sheet gaskets: Aramid, Glass, NBR
234.4737116 SF 5000, Compressed Fiber Sheet gaskets: Carbon, Aramid, NBR
63.276264 Flexicarb NR, Compressed Fiber Sheet gaskets
63.276264 Flexicarb SR, Compressed Fiber Sheet gaskets: Graphite, Flat 316SS Core
175.7674 Flexicarb ST, Compressed Fiber Sheet gaskets: Graphite, Tanged 316SS Core
175.7674 Flexpro (Kammprofile), facing material : Flexicarb Flexible Graphite
175.7674 Flexpro (Kammprofile), facing material : PTFE
175.7674 2500.0 Flexpro (Kammprofile), facing material : Soft Materials
175.7674 MRG (Metal Reinforced Gasket) gasket
1265.52528 RTJ (Ring type Joints), Iron or soft steel
1532.691728 RTJ (Ring type Joints), Monel or 4%-6% chrome
1827.98096 RTJ (Ring type Joints), Stainless steel or Nickel based alloys
3.5 456.9952
3.75 534.3329
3.5 562.4557
3.75 632.7626
3.75 632.7626
3.25 386.6883
3.5 456.9952
3.75 534.3329
3.75 632.7626
4.25 710.1003
4 618.7012
4.75 913.9905
5.5 1265.525
6 1532.692
6.5 1827.981
5.5 1265.525
6 1532.692
6.5 1827.981
2 201
3 703
16SS Core
d 316SS Core
on protection)