Sunteți pe pagina 1din 17

Model 356A12

Triaxial ICP accelerometer, 100 mV/g, 50 g, 0.5 to 5k Hz, 5gm, 5 foot

Installation and Operating Manual

For assistance with the operation of this product,


contact PCB Piezotronics, Inc.

Toll-free: 800-828-8840
24-hour SensorLine: 716-684-0001
Fax: 716-684-0987
E-mail: info@pcb.com
Web: www.pcb.com
Warranty, Service, Repair, and
Return Policies and Instructions

The information contained in this document supersedes all similar information that
may be found elsewhere in this manual.

Total Customer Satisfaction PCB Calibration Routine calibration of


Piezotronics guarantees Total Customer sensors and associated instrumentation
Satisfaction. If, at any time, for any is recommended as this helps build
reason, you are not completely satisfied confidence in measurement accuracy
with any PCB product, PCB will repair, and acquired data. Equipment
replace, or exchange it at no charge. calibration cycles are typically
You may also choose to have your established by the users own quality
purchase price refunded in lieu of the regimen. When in doubt about a
repair, replacement, or exchange of the calibration cycle, a good rule of thumb
product. is to recalibrate on an annual basis. It is
also good practice to recalibrate after
Service Due to the sophisticated exposure to any severe temperature
nature of the sensors and associated extreme, shock, load, or other
instrumentation provided by PCB environmental influence, or prior to any
Piezotronics, user servicing or repair is critical test.
not recommended and, if attempted,
may void the factory warranty. Routine PCB Piezotronics maintains an ISO-
maintenance, such as the cleaning of 9001 certified metrology laboratory and
electrical connectors, housings, and offers calibration services, which are
mounting surfaces with solutions and accredited by A2LA to ISO/IEC 17025,
techniques that will not harm the with full traceability to SI through
physical material of construction, is N.I.S.T. In addition to the normally
acceptable. Caution should be observed supplied calibration, special testing is
to insure that liquids are not permitted to also available, such as: sensitivity at
migrate into devices that are not elevated or cryogenic temperatures,
hermetically sealed. Such devices phase response, extended high or low
should only be wiped with a dampened frequency response, extended range,
cloth and never submerged or have leak testing, hydrostatic pressure
liquids poured upon them. testing, and others. For information on
standard recalibration services or
Repair In the event that equipment special testing, contact your local PCB
becomes damaged or ceases to Piezotronics distributor, sales
operate, arrangements should be made representative, or factory customer
to return the equipment to PCB service representative.
Piezotronics for repair. User servicing or
repair is not recommended and, if Returning Equipment Following
attempted, may void the factory these procedures will insure that your
warranty. returned materials are handled in the
most expedient manner. Before
returning any equipment to PCB PCB for a complete statement of our
Piezotronics, contact your local warranty. Expendable items, such as
distributor, sales representative, or batteries and mounting hardware, are
factory customer service representative not covered by warranty. Mechanical
to obtain a Return Warranty, Service, damage to equipment due to improper
Repair, and Return Policies and use is not covered by warranty.
Instructions Materials Authorization Electronic circuitry failure caused by the
(RMA) Number. This RMA number introduction of unregulated or improper
should be clearly marked on the outside excitation power or electrostatic
of all package(s) and on the packing discharge is not covered by warranty.
list(s) accompanying the shipment. A
detailed account of the nature of the Contact Information International
problem(s) being experienced with the customers should direct all inquiries to
equipment should also be included their local distributor or sales office. A
inside the package(s) containing any complete list of distributors and offices
returned materials. can be found at www.pcb.com.
Customers within the United States may
A Purchase Order, included with the contact their local sales representative
returned materials, will expedite the or a factory customer service
turn-around of serviced equipment. It is representative. A complete list of sales
recommended to include authorization representatives can be found at
on the Purchase Order for PCB to www.pcb.com. Toll-free telephone
proceed with any repairs, as long as numbers for a factory customer service
they do not exceed 50% of the representative, in the division
replacement cost of the returned responsible for this product, can be
item(s). PCB will provide a price found on the title page at the front of this
quotation or replacement manual. Our ship to address and
recommendation for any item whose general contact numbers are:
repair costs would exceed 50% of
replacement cost, or any item that is not PCB Piezotronics, Inc.
economically feasible to repair. For 3425 Walden Ave.
routine calibration services, the Depew, NY14043 USA
Purchase Order should include Toll-free: (800) 828-8840
authorization to proceed and return at 24-hour SensorLineSM: (716) 684-0001
current pricing, which can be obtained Website: www.pcb.com
from a factory customer service E-mail: info@pcb.com
representative.

Warranty All equipment and repair


services provided by PCB Piezotronics,
Inc. are covered by a limited warranty
against defective material and
workmanship for a period of one year
from date of original purchase. Contact
PCB - RoHS2
PCB Industrial Monitoring and Measuring Equipment - China RoHS 2 Disclosure Table


(Pb) (Hg) (Cd) (Cr(VI)) (PBB) (PBDE)
O O O O O O
PCB X O O O O O
O O O O O O
X O O O O O
O O O O O O
O O O O O O
O O O O O O
O O X O O O
O O O O O O
X O O O O O
O O O O O O
X O O O O O
/ X O O O O O
SJ/T 11364
O GB/T 26572
X GB/T 26572
RoHS2011/65/ EU

CHINA RoHS COMPLIANCE


Component Name Hazardous Substances
Lead Mercury Cadmium Chromium VI Polybrominated Polybrominated
(Pb) (Hg) (Cd) Compounds Biphenyls Diphenyl
(Cr(VI)) (PBB) Ethers (PBDE)
Housing O O O O O O
PCB Board X O O O O O
Electrical O O O O O O
Connectors
Piezoelectric X O O O O O
Crystals
Epoxy O O O O O O
Teflon O O O O O O
Electronics O O O O O O
Thick Film O O X O O O
Substrate
Wires O O O O O O
Cables X O O O O O
Plastic O O O O O O
Solder X O O O O O
Copper Alloy/Brass X O O O O O
This table is prepared in accordance with the provisions of SJ/T 11364.
O: Indicates that said hazardous substance contained in all of the homogeneous materials for this part is below the limit
requirement of GB/T 26572.
X: Indicates that said hazardous substance contained in at least one of the homogeneous materials for this part is above
the limit requirement of GB/T 26572.
Lead is present due to allowed exemption in Annex III or Annex IV of the European RoHS Directive 2011/65/EU.

DOCUMENT NUMBER: 21354


DOCUMENT REVISION: C
ECN: 45605
4 3 2 1
PCB Piezotronics Inc. claims proprietary rights in
the information disclosed hereon. Neither it nor any REVISIONS
081-XXXX-90
reproduction thereof will be disclosed to others
without the written consent of PCB Piezotronics Inc.
REV DESCRIPTION DIN

STANDARD STUD MOUNT P UPDATE DRAWING 25686

"A" "B" "C" "D"


5-40 M3 X 0.50 10-32 M5 X 0.80
SENSOR MOUNTING INSTRUCTIONS MOUNTING INSTRUCTIONS MOUNTING INSTRUCTIONS MOUNTING INSTRUCTIONS
(METRIC DIMENSIONS IN BRACKETS) (ENGLISH DIMENSIONS IN BRACKETS) (METRIC DIMENSIONS IN BRACKETS) (ENGLISH DIMENSIONS IN BRACKETS)

2 2
2 2

B B

SENSOR THREAD
"A"
SENSOR
SENSOR THREAD
THREAD "X" MOUNTING HOLE PREPARATION: MOUNTING HOLE PREPARATION: MOUNTING HOLE PREPARATION: MOUNTING HOLE PREPARATION:
1 .101[2.57] 1 2.5[.099]
1 .159[4.04] 1 4.22[.166]
X .20[5.1] MIN. X 4.6 [1.8] MIN. X .23[5.8] MIN. X 7.62 [.300] MIN.
MOUNTING
"X" 5-40 UNC-2B M3 X 0.50-6H 10-32 UNF-2B M5 X 0.8-6H
THREAD MOUNTING
X .15[3.8] MIN. X 3.3[.13] MIN. X .15[3.8] MIN. X 5.08[.200] MIN.
THREAD
MOUNTING THREAD SEE DRAWING
5-40 A 4.) RECOMMENDED MOUNTING TORQUE,
4.) RECOMMENDED MOUNTING TORQUE, 4.) RECOMMENDED MOUNTING TORQUE,
4.) RECOMMENDED MOUNTING TORQUE, 113-225 NEWTON CENTIMETERS
M3 X 0.50 B 45-55 NEWTON CENTIMETERS 10-20 INCH POUNDS
10-32 C 4-5 INCH POUNDS [10-20 INCH POUNDS].
[4-5 INCH POUNDS]. [113-225 NEWTON CENTIMETERS].
M5 X 0.80 D [45-55 NEWTON CENTIMETERS].
1/4-28 E
M6 X 1.00 F

INTEGRAL STUD MOUNT "THRU-BOLT" STUD MOUNT "E" "F" "G"


1/4-28 M6 X 0.75, M6 X 1.00, M8 X 1.25 MOUNTING INSTRUCTIONS
MOUNTING INSTRUCTIONS MOUNTING INSTRUCTIONS 2
FOR SPECIAL THREAD LENGTHS
"THRU-BOLT" (METRIC DIMENSIONS IN BRACKETS) (ENGLISH DIMENSIONS IN BRACKETS) (METRIC DIMENSIONS IN BRACKETS)

SENSOR
M6 X 0.75
SENSOR 2
MOUNTING HOLE PREPARATION: "B"
2 "C"
1 5.31[.209]
X 7.62 [.300] MIN.
M6 X 0.75-6H
"X" X 5.08[.200] MIN. "P"
INTEGRAL "X"
MOUNTING HOLE PREPARATION: MOUNTING HOLE PREPARATION:
MOUNTING "A" M6 X 1.0 M8 X 1.25
1 .218[5.54]
1 DRILL DIA.
STUD "A" MOUNTING HOLE PREPARATION: MOUNTING HOLE PREPARATION:
X .300[7.62] MIN. X "C" MIN.
MOUNTNG THREAD SEE DRAWING 1 5.05[.199] 1 6.75[.266] 1 THREAD PITCH TAP
1/4-28 UNF-2B
5-40 A BOLT THREAD SEE DRAWING X 8.10 [.320] MIN. X 8.64 [.340] MIN. SHOWN
X "B" MIN.
10-32 C X .200[5.08] MIN.
A M3 X 0.50 B M6X 1.0-6H M8 X 1.25-6H A
10-32 C M5 X 0.80 D X 6.35[.250] MIN. X 5.00[.197] MIN.
THREAD DEPTH : B= X + 1 THREAD PITCH
1/4-28 E 4.) RECOMMENDED MOUNTING TORQUE, DRILL DEPTH : C= B + 3 THREAD PITCH
M5 X 0.80 D
M6 X 1.00 F 2-5 FOOT POUNDS 4.) RECOMMENDED MOUNTING TORQUE, SEE A-F FOR APPROPRIATE DRILL AND TAP
1/4-28 E
M6 X 1.00 F M8 X 1.25 F [3-7 NEWTON METERS]. 3-7 NEWTON METERS [2-5 FT POUNDS]. THREAD PITCH= 1/TPI [P]

UNLESS OTHERWISE SPECIFIED TOLERANCES ARE: DRAWN CHECKED ENGINEER


DIMENSIONS IN INCHES DIMENSIONS IN MILLIMETERS
[ IN BRACKETS ] JDM 3/9/07 ECB 3/9/07 JJD 3/9/07

3.) FOR BEST RESULTS, PLACE A THIN LAYER OF SILICONE GREASE (OR EQUIVALENT) ON INTERFACE PRIOR DECIMALS XX .01 DECIMALS X 0.3 TITLE
3425 WALDEN AVE. DEPEW, NY 14043
TO MOUNTING. XXX .005 XX 0.13 (716) 684-0001 E-MAIL: sales@pcb.com
63[1.61] INSTALLATION DRAWING
2 MOUNTING SURFACE SHOULD BE FLAT TO WITHIN .001(0.03) TIR OVER DIM 'A' WITH A OR BETTER FINISH FOR BEST RESULTS. ANGLES 2 DEGREES ANGLES 2 DEGREES CODE DWG. NO.
FOR STANDARD
081 SERIES MOUNTING
IDENT. NO.
52681 081-XXXX-90
1 DRILL PERPENDICULAR TO MOUNTING SURFACE TO WITHIN 1. FILLETS AND RADII FILLETS AND RADII
.003 - .005 0.07 - 0.13 SCALE: N.T.S. SHEET 1 OF 1
4 3 2 1

S-ar putea să vă placă și