Documente Academic
Documente Profesional
Documente Cultură
P/N 109422
Motorola AP-5131 Access Point Quick Setup Guide
GettingStarted
1. These instructions were written for the AP-5131 using firmware version 1.1.0.0-045R.
The configuration steps and screens may vary with different firmware.
2. Confirm the following programs are available on the computer used to configure the
AP-5131.
Internet Explorer 6.0, or higher, set as the computers default browser.
Sun Microsystems Java 2 (JRE) version 1.5 or higher (available from Suns
Website).
o Disable Microsofts Java Virtual Machine if installed.
o To test the computers Java 2 environment, visit
http://www.java.com/en/download/help/testvm.jsp
BasicAP5131Configuration
1. Change the computers IP Address to 10.1.1.2.
Windows XP Windows Vista
a. Click on Start a. Click on Windows Start icon
b. Select Control Panel b. Select Control Panel.
c. Select Network Connections. c. Select Network and Internet.
d. Right Click Local Area Connections d. Select Network and Sharing Center.
e. Select Properties. e. Select Manage network connections
f. Select Internet Protocol, (TCP/IP) (left column).
g. Select Properties f. Right click on Local Area Connection
h. Select Use the following IP g. Select Properties.
address. h. Select Internet Protocol Version 4
i. IP Address = 10.1.1.2 (TCP/IPv4)
j. Subnet mask = 255.0.0.0. i. Select Properties.
k. Click Ok and Ok. j. Select Use the following IP
l. Close the Local Area Connection address.
Status. k. IP Address = 10.1.1.2
l. Subnet mask = 255.0.0.0.
m. Click Ok and Ok.
n. Close Network connections.
o. Close Network and Sharing Center.
If the Help Viewing Java message is the only information displayed it indicates
the Java software required by the Motorola AP-5131 configuration software is
not installed on the computer.
Click the link and follow the instructions to download Sun Java 1.5.0 or
greater.
11. If disconnect occurs, at the AP login screen enter the user name and password.
See figure1.
Username: admin
Password: ishida (Note: if not ishida, enter the appropriate password)
12. Click Login.
13. Configuration cannot proceed until a country has been selected. At the warning
message, click OK. See figure 5.
14. Select United States using drop down menu. See figure 6.
15. Under WLAN#1 settings, enter the ESSID name (Wireless Network Name). The
stores name is normally used entered in lower case with no spaces.
Example: foodstore
16. Enter the Name. Normally, this indicates the Access Points location in the store.
Example: Deli Dept
20. Enter the Default Gateway address. This is the IP Address of the stores router. It
must be in the same range as the Access Point and scales.
Example: 192.168.10.1
21. Set the Primary DNS Server as zeros.
24. Internet Explorer has logged out of the AP-5131 configuration application.
25. Close Internet Explorer.
26. Move the Ethernet cable from the WAN port on the AP-5131 to Data In on the
Power Injector. The Ethernet cables should be connected as listed below.
Power Injector Data In to the computer.
Power Injector Data and Power Out to the AP-5131 LAN port.
27. Change the computers IP address and subnet to the range of the Access Point.
Example: IP Address: 192.168.10.2
Subnet Mask: 255.255.255.0.
28. Basic setup is complete.
29. The scale(s) may now be configured to communicate on the wireless network.
The IP addresses of the scale(s) and the computer must be in the same range
as the access point.
ConfiguringEncryptionontheAP5131
Add encryption to all scales prior to encrypting the Access Point.
Once the AP is encrypted it cannot connect to any unencrypted scale(s).
1. Open Internet Explorer and enter the IP Address that was assigned to the Access
Point during basic configuration: http://xxx.xxx.xxx.xxx
Example: http://192.168.10.10
2. Press Enter.
3. At the AP log in screen enter the user name and password. See figure 1.
Username: admin
Password: ishida (Note: if not ishida, enter the appropriate password)
4. Click Login.
5. Select Quick Setup from the left side menu bar. See figure 9.
6. Locate Security Policy on the bottom right of the screen, select Create.
7. On the New Security Policy screen enter the new Name. For the new name use
scales. (lower case).
8. On the left side of the screen choose the encryption method to be used.
The AC-4000, BC4000, and OMNi-4000 support both WEP and WPA.
The SR-2000a, IL-2000sa, and IL-EMZ support only WEP.
Use extreme care when entering the encryption key. An incorrect key will
prevent communication with the wireless scale(s) in the network.
9. Choose the encryption type and enter the key as designated by the encryption
selection. (See Appendix 1 for information on WPA encryption).
10. Leave Pass Key blank
WEP 64 (40 bit key) See figure 10.
For Key #1 enter 10 hexadecimal characters
Example: 12345abcde
11. Click on Apply after selecting the encryption type and entering the key.
12. When the WEB UI Disconnection Warning appears, select OK. See figure 8.
13. Set the Security Policy to scales using the drop down menu on the Quick Setup
window. See figure 12.
NOTES
Power Injector
o The power injector can cabled be up to 300 ft from the AP device for final
installation.
o Do Not block or cover airflow to the Power Injector
o Keep the Power Injector away from excessive heat, humidity, vibration and
dust.
o The power injector is not a repeater, and does not amplify the Ethernet
signal. Ensure the Power Injector is placed as close as possible to the
network data port.
Scale Configuration
o Refer to the following documents for wireless configuration information.
These items can be found on the Rice Lake Weighing Systems Retail
Solutions distributor site at www.ricelake.com/retail or the Rice Lake Retail
System Support Tool CD (p/n 77369).
o AC-4000: Symbol CB3000 Client Bridge Quick Setup (p/n 93207)
o BC-4000: BC-4000 CB3000 Quick Setup (p/n 101875)
o SR-2000a: SR-2000a Quick Setup Instructions
Channel Selection
o The AP-5131 default setting is Automatic Selection. This enables the AP-
5131 to auto-select the channel of operation. For example, if three AP-5131
Access Points are operating, each AP-5131 would be set to a non-
overlapping channel (1, 6 and 11).
o If non-Motorola (Symbol) Access Points are also in use the channel can be
manually set to avoid interference. Channel selection is made under Network
Configuration, Radio Configuration, Radio 1. See figure 13.
Appendix1,WPAEncryption
The following screens show the settings and encryption key requirements for WPA.