Documente Academic
Documente Profesional
Documente Cultură
COMPLETION EQUIPMENTS
Time: 30 minutes
1. Given the drawing above, match the correct numbers to their descriptions.
LMV FWV
UMV KWV
SSV Cross
2. Which of the following statements about X-mas tree valves are true?(2 answers)
a. After closing, a manual valve should be backed out by part of a turn
b. The valve must be closed as tightly as possible
c. All valves take 30 turns to open or close
d. The indicator shows how many turns have been made
e. Counting the turns as the valve is opened or closed can show any obstructions in
front of the valve
4. Which of the following statements about tubing hangers are true?(3 answers)
a. A plug can usually be set inside the hanger body
b. It supports the weight of the production casing and completion
c. It supports the weight of the top of completion
d. It allows communication from inside the completion to the completion annulus
through the control line port(s)
e. It allows communication into the completion annulus through the control line
port(s)
f. It isolates the completion from the completion annulus
g. It can be closed by applying pressure to the control line
16. What stops wellbore fluids entering the annulus through a gas lift valve in an SPM?
a. Differential Pressure
b. A check valve in the gas lift valve
c. The venture effect across the port of the gas lift valve
17. If a SPM is not in use as a circulating device, what type of valve is installed in the
side pocket as a positive closure from either direction?
a. A gas lift valve
b. A gate valve
c. A dummy valve
d. A chemical injection valve
e. A circulating valve
20. What is the primary reason that determines the setting depth of the DHSV?
a. To prevent deliberate sabotage
b. Is set as high as possible to reduce the inventory of wellbore fluids that might
escape
c. Is set below the depth where it can be damaged by surface impact or explosion
d. Is set below the crater depth from a blow out around the casing
e. Is set as close to the packer as possible
f. To prevent penetration of drilling tools from an adjacent well
21. From which direction does a DHSV prevent flow?
a. Above
b. Below
c. Above and Below
24. How do flow control devices seal within the nipple bore?
a. With slips
b. On No-Go shoulders
c. With locking dogs in matching profiles
d. With expanding rubber elements in the bore
e. With elastomeric packings in the bore
f. By metal to metal seals
28. What type of closure mechanism is fitted to surface controlled wireline retrievable
DHSVs?(2 answers)
a. Poppet
b. Flapper
c. Plug
d. Ball
e. Sleeve
f. Gate
29. Which of the following DHSVs are surface controlled?(2 answers)
a. Differential pressure
b. Ambient pressure
c. Wireline retrievable
d. Tubing retrievable
e. Ball
f. Flapper
g. Automatic
30. What type of closure mechanism is fitted to tubing retreivalbe DHSVs? (2 answers)
a. Poppet
b. Flapper
c. Plug
d. Ball
e. Sleeve
f. Gate
32. Which DHSV has the largest ID for the same tubing size?
a. Wireline retrievable
b. Ambient pressure
c. Tubing retrievable
d. Differential pressure
33. What is the correct action to take to re-instate production in a well with a failed tubing
retrievable DHSV?
a. Workover the well
b. Lock open the DHSV
c. Lock open the DHSV and install an insert valve
34. How is a tubing retrievable DHSV run in the open position?(2 answers)
a. With pressure on the control line
b. By using the lock open mechanism
c. With a straddle set across the valve
d. By keeping the tubing pressurised
37. How is a surface controlled wireline retrievable DHSV run in the open position?
a. With locked in hydraulic pressure
b. With a lock open sleeve
c. With a prong on the wireline running tool
d. With an automatic J device
40. How is temporary communication normally made between the tubing and annulus?(2
answers)
a. Open the SSD
b. Punch a hole in the tubing
c. Connect the tubing and annulus in the surface
d. Install a circulating valve in the SPM
Question Question
Answer Answer
Number Number
1 9,5,8,4,6,3,1,2,10,7 22 A
2 A&E 23 C
3 B 24 E
4 A,C&F 25 A
5 C 26 B
6 B 27 B&C
7 B&D 28 B&D
8 C 29 C&D
9 B 30 B&D
10 A 31 A&B
11 C 32 C
12 A 33 C
13 B&D 34 A&C
14 C 35 D
15 C&E 36 B
16 B 37 C
17 C 38 C
18 E 39 D
19 B 40 A&D
20 C 41 A&B
21 B