Documente Academic
Documente Profesional
Documente Cultură
INSTALLATION MANUAL
Applied Machines: C754e/C654e/C754/C654/C554e/C554/754e/654e/754/654/554e
COLOR MFP: 75 ppm/65 ppm/55 ppm
MFP: 75 ppm/65 ppm/55 ppm
Product Code: A2X0/A2X1/A5AY/A2XK/A55V/A5YN/A61D
Caution:
No. Name Shape Qty
Lifting the machine in an awkward position or
transporting it in a poorly balanced position could 8. Mounting
result in personal injury. When transporting the bracket G
machine, assign an adequate number of persons 1
to the job and ensure that each person can take a
good position of not being excessively loaded. A2Y1IXC007DA
A2Y1IXC008DA
A2Y1IXC001DB
11. Exit tray
2. Mounting (upper)
bracket A *1 1
1
A11PIXC001DB
A2Y1IXC002DA
12. Exit tray
3. Mounting (lower)
bracket B *1
1 1
A2Y1IXC003DB A07UIXC065DA
5. Mounting A11PIXC035DA
A2Y1IXC005DB 1
6. Mounting
bracket E *1 A3EPIXC010DA
A11PIXC019DB 1
7. Mounting
bracket F *2 A3EPIXC011DA
A2Y1-9550-14C
E-1
Note:
No. Name Shape Qty
Before installing this finisher to C554e/C554/
17. Screw A *3 554e, the paper feed cabinet PC-110, PC-210,
(4 x 8 mm) 8 PC-410, or the desk DK-510 needs to be
4038IXC033DA installed in advance.
18. Screw B *4 This manual provides the illustrations of the
accessory parts and machine that may be
(4 x 16 mm) 4 slightly different in shape from yours. In that
case, instead of the illustrations, use the
A2Y1IXC043DA
appearance of your machine to follow the
19. Screw C *2 installation procedure. This does not cause any
(3 x 16 mm) 5 significant change or problem with the proce-
A2Y1IXC044DA dure.
20. Screw D If none of the later steps instruct you to use the
(3 x 6 mm) 5 parts including screw and cover that you
9735
removed following the instructions described in
this manual, discard them.
21. Screw E
(4 x 8 mm) 2
A092IXC012DA
4980IXC019DA
E-2
III. Installation procedures 5. Remove the protective sheet of the horizontal
transport unit.
Note:
The parts to be used and the procedure for install-
ing this option depend on the type of the main unit
to which this option is installed. Please go to one
of the following pages that correspond to the type
of your main unit.
When installing this option to C754e/C654e/
C754/C654/754e/654e/754/654: E-3
When installing this option to C554e/C554/
554e: E-6
A2Y1IXC046DB
A2Y1IXC010DA
Guide
A2Y1IXC012DA
A3EPIXC062DA
E-3
8. Remove the cover shown in the illustration. 11. Attach the guide plate B. (Two screws removed
(Three screws) in step 9)
A2Y1IXC013DA A2Y1IXC016DA
9. Remove the cover shown in the illustration from 12. Attach the supplied mounting bracket A (front) to
the front of the horizontal transport unit. (Two the left side of the main unit. (Two supplied
screws) screws A)
A2Y1IXC014DA A2Y1IXC017DA
10. Attach the guide plate A to the horizontal trans- 13. Attach the supplied mounting bracket B (rear) to
port unit by fitting the two tabs into the slots. the left side of the main unit. (Two supplied
screws A)
A2Y1IXC015DA
A2Y1IXC018DB
E-4
14. Mount the horizontal transport unit to the main 16. Attach the supplied mounting bracket G to the
unit. (Two supplied screws A) left side of the main unit. (Two supplied screws
B)
A2Y1IXC019DB
A2Y1IXC021DA
A2Y1IXC022DA
A2Y1IXC020DB
E-5
<When installing this option to C554e/C554/554e> 6. Remove protective tape of the horizontal trans-
1. Turn off the machine and unplug the power cord port unit.
from the power outlet.
2. Remove the users guide holder from the main
unit.
A2Y1IXC046DB
A2Y1IXC023DB
A2Y1IXC057DA
A2Y1IXC024DB
A2Y1IXC045DA
A2Y1IXC025DB
E-6
10. Attach the supplied mounting bracket F to the 18. Remove the protective tape and the protective
left side of the main unit. (Two supplied screws materials from the finisher.
B)
Note:
Temporarily fix the cable of the horizontal trans-
port unit onto the upper portion of the machine to
prevent it from being caught by the mounting
bracket F.
A2Y1IXC047DA
OK NG
A11PIXC007DD
A2Y1IXC028DB
A2Y1IXC029DB
Mounting bracket H
A2Y1IXC048DC
A3EPIXC017DA
E-7
19. Attach the supplied mounting bracket I to the 22. Install the finisher on the main unit.
right side of the finisher at the position shown in Note:
the illustration. (One supplied screw D) Align the hook portion of the mounting bracket E or
the mounting bracket F with the hole on the right
side of the finisher. Then, push the finisher toward
the rear.
A2Y1IXC042DB
A2Y1IXC031DA
A2Y1IXC035DB
A2Y1IXC033DA
E-8
24. Insert the supplied exit tray (upper) into the sub 26. Remove the cover shown in the illustration from
tray paper exit slot on the finisher. the back of the main unit. (One screw)
Note:
<When installing this option to C754e/C654e/C754/
When installing the exit tray (upper), insert the left
C654/754e/654e/754/654>
and right side projections on the finisher into the
holes located on both ends of the exit tray (upper),
respectively.
A2Y1IXC036DA
A11PIXC013DB
Note:
When installing the exit tray (lower), hook the
guide holes of the exit tray (lower) over the four
mounting clamps and then fix it.
A11PIXC014DA
E-9
27. Plug in the two connectors of the finisher. Fit the 29. Reinstall the users guide holder, which has
head of the cable tie into the mounting hole on been removed in step 2, to the upper or lower
the main unit. position shown.
<When installing this option to C754e/C654e/C754/ Mounting the holder to the upper position
C654/754e/654e/754/654>
Connector
Cable tie
A2Y1IXC039DA
A2Y1IXC037DB
Mounting the holder to the lower position
Connector
Cable tie
A2YUIXC022DA A2Y1IXC040DA
28. Reattach the cover removed in step 26. 30. Push the rear left part of the finisher toward the
(One screw) main unit to place the finisher parallel to the
Note: main unit. Bring the plate springs of the mount-
Be careful not to pinch the harness. ing bracket E or the mounting bracket F into con-
When installing this option to C554e/C554/ tact with the plate of the finisher.
554e, insert two tabs A into the holes on the Note:
main unit cover first. Ensure the above mentioned process to be done
Then fit two tabs B into the holes. appropriately in order to secure the finishers
grounding.
<OK>
Contacted
<NG>
Tab B
Tab A
E-10
IV. Installation check 2. Open the finishers front door.
3. Adjust the height of the casters at the paper exit
Make sure that the main unit contacts with the plate side of the finisher (front/rear) to place the plate
spring of the mounting bracket I attached in the step spring in contact with the main unit.
19 of III. Installation procedures.
<OK> <NG> 4. Attach the cover removed in step 1 and close the
Contacted Not contacted finishers front door.
A2Y1IXC049DA
A2Y2IXC022DC
A2Y1IXC050DA
E-11
3. Remove the driven part. (Three screws) 5. Remove the cover shown in the illustration from
the finisher. (Six screws)
A2Y2IXC021DB
A2Y1IXC054DA
A2Y2IXC020DB
A2Y1IXC056DA
E-12