Documente Academic
Documente Profesional
Documente Cultură
TRADEMARK
WOODCO
USA
REG. U.S. PATENT OFFICE
WOODCO USA provides Web Site Tools for identification, estimating, and reference only. Do
not use this information for manufacturing or inspection. Users of these tools should not use
them as a substitute for professional engineering advice. Anyone making use of the information
presented does so at his own risk and assumes any and all liability resulting from such use.
WOODCO USA
P.O. Box 1261
Houston, Texas 77251-1261
Phone: 713-672-9491
U.S. and Canada: 1-800-496-6326
Fax: 713-672-8768
www.woodcousa.com
Email: sales@woodcousa.com
See page 9 and 10 of this document for Clamp installation, inspection and storage instructions.
Ring Clamp Torque
Hub Size Stud Bolt Wrench Size
Gasket Number Ft. Lbs.
See page 9 and 10 of this document for Clamp installation, inspection and storage instructions.
Ring Clamp Torque
Hub Size Stud Bolt Wrench Size
Gasket Number Ft. Lbs.
* Not API
See page 9 and 10 of this document for Clamp installation, inspection and storage instructions.
Ring Clamp Torque
Hub Size Stud Bolt Wrench Size
Gasket Number Ft. Lbs.
* Not API
See page 9 and 10 of this document for Clamp installation, inspection and storage instructions.
Ring Clamp Torque
Hub Size Stud Bolt Wrench Size
Gasket Number Ft. Lbs.
* Not API
See page 9 and 10 of this document for Clamp installation, inspection and storage instructions.
Ring Clamp Torque
Hub Size Stud Bolt Wrench Size
Gasket Number Ft. Lbs.
* Not API
See page 9 and 10 of this document for Clamp installation, inspection and storage instructions.
Ring Clamp Torque
Hub Size Stud Bolt Wrench Size
Gasket Number Ft. Lbs.
* Not API
See page 9 and 10 of this document for Clamp installation, inspection and storage instructions.
Ring Clamp Torque
Hub Size Stud Bolt Wrench Size
Gasket Number Ft. Lbs.
* Not API
WASHER DETAIL
NUT
XXXXXX
XXXXXX
WUSA
INNER WASHER (BEARING) BLUE
XXXXXX
XXXXXX KEEP WOODCO
Inspection requires a thorough cleaning, removing all API 16A Hubs have ring grooves similar to, or exactly the
dirt, paint, rust, etc. same as, those ring grooves in API 6A flanges. Evaluating
ring grooves in both Hubs and flanges involve the same
Inspection should include particular care to positively practices. For an online guide to Appraisal of Ring
identify clamp halves, matching them as to manufacturer Grooves, go to www.woodcousa.com/field_appr.htm.
and individual serial number (WOODCO USA uniquely
identifies each assembly with a manufacturing work order Caution: API 16A Hub connections differ from
number followed by the item manufacturing sequence flanges in that the ring groove, face, Hub O.D.,
number e.g. WO 12345-01 on each half). and Hub edge width, all must conform to the exact
Perform a visual inspection for obvious handling damage, API specified dimensions and tolerances in order
corrosion, cracks, and galls. The 25 ramp inside the clamp to seal and function reliably. Field measurements
should not have gouges, or deep pits. It should feel smooth on all of these dimensions require special tools
to the touch (after cleaning). Clamps that do not appear and skills, only knowledgeable persons qualified
damaged do not require dimensional inspection. to perform dimensional inspection on Hub
connections should do so.
Caution: If circumstances should require
dimensional inspection, keep in mind that API Hub ring grooves cannot have repair performed by skim
publishes no specific dimensions for clamps, cutting the Hub face and deepening the groove. Any groove
but supplies only design requirements with rework beyond polishing must include weld repair to the
allowable stress levels. Clamps made by different Hub to provide stock for repair machining. If operators
expect to connect and disconnect Hub connection
manufacturers will not likely have identical
equipment and store the equipment for any extended time,
critical dimensions. Measurement of these critical the operator would do well to specify corrosion resistant
dimensions requires special tools and skills and material inlay in the ring grooves at the time of original
only knowledgeable persons qualified to perform order.
dimensional inspections on clamps should do so.
Measuring clamp dimensions and comparing one If circumstances require weld repair to existing used Hub
manufacturers dimensions to those of another connected equipment, operators should consider adding
corrosion resistant material inlay to the existing Hubs at
manufacturer will lead to false reports of non-
the time of repair.
conformance.
Beyond the ring grooves, API 16A specified Hubs should
Evaluate bolts and nuts to the same criteria as used for
appear free of corrosion and pitting on the 25 backface
flange bolting, and replace these parts if questionable.
ramps where Clamps must contact and slide to pull the
Replace any missing or damaged spherical washers.
connections together. The backface ramp should feel
Operators should store assembled, matched, clamp sets smooth to the touch (after cleaning).
providing adequate protection from corrosion until next
Storage of Hub connected equipment should include
use.
protection of the entire Hub area from corrosion and
Persons making any assembly of pressure control handling damage.
equipment should conduct a Pressure Test of the assembly,
Persons making any assembly of pressure control
with a hold period before use.
equipment should conduct a Pressure Test of the assembly,
Persons wishing to test loose Clamps to qualify them for with a hold period before use.
later use on any Hub they will fit, should test them using
Persons wishing to test assembled equipment, with or
Hubs that apply the highest load at test pressure. For a
without internal closure mechanisms, should make their
table of Clamps with test pressures on-line, go to www.
test consistent with the normative practices as shown in
woodcousa.com/clamp_load_main.htm.
API Specs 6A and 16A.
1. WOODCO USA may change, add, or remove portions of its website at any time. WOODCO USA
also may impose limits on certain features and services or restrict access to all or any part of its
website without notice or liability.
2. WOODCO USA intends its website (the Content) for your personal use only.
3. All materials published on the WOODCO USA website have copyright protection pursuant to U.S.
and international copyright laws. You may not modify, publish, transmit, participate in the transfer
or sale of, reproduce (except as provided in Paragraph 4 below), create new works from, distribute,
perform, display, or in any way exploit any of the Content in whole or in part. You shall abide by all
additional copyright notices, information, and other restrictions associated with any of the Content.
4. You may download or copy the Content and other downloadable items forming parts of the Content
for personal use only, provided that you maintain all copyright and other notices contained therein.
You may not copy or store any Content for other than personal use without prior written permission
from an officer of WOODCO USA.
5. WOODCO USA does not assume liability for any errors or omissions in the Content, or in the
transmission or delivery of all or any part thereof, or for any damages arising there from. You
acknowledge sole responsibility (sole risk) for any reliance you may have in the Content or actions
you may take relying upon any of the Content. WOODCO USA makes every effort to assure the
accuracy of the Content, but, WOODCO USA MAKES THE CONTENT AVAILABLE TO YOU ON
AN AS IT APPEARS BASIS, WITHOUT WARRANTIES OF ANY KIND, EITHER EXPRESS OR
IMPLIED, INCLUDING, WITHOUT LIMITATION, ANY WARRANTIES OF TITLE OR IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. YOU
HEREBY ACKNOWLEDGE THAT YOU USE THE CONTENT AT YOUR SOLE RISK.
6. You shall have no rights to any of the proprietary rights associated with any of the Content.
7. WOODCO USA may, in its sole discretion, terminate or suspend access to all or part of the Content
for any reason, including without limitation, breach or assignment of this Agreement.
8. This Agreement originates in Houston, Texas and any interpretation and/or enforcement shall
comply with Texas law. Any action to enforce this agreement shall occur in, and only in, the federal
or state courts located in Harris County, Texas.
9. Privacy - Please review our Privacy Policy, which also governs your visit to woodcousa.com, to
understand our practices.
10. Please direct all questions to: sitemaster@woodcousa.com
WOODCO USA will enforce all rights under copyright law, regarding all photographs, graphics, written
materials or other content appearing on this website, the legally protected property of WOODCO
USA. WOODCO USA prohibits reproduction or re-use of any kind, other than that described in Terms
of Use above, without written permission from an officer of WOODCO USA.Submit all requests for
re-use of copyrighted materials in writing to: sitemaster@woodcousa.com