Documente Academic
Documente Profesional
Documente Cultură
Title
Description
Determine the ultimate moment of resistance of the cross-section shown in figure given that
the characteristic strengths are f y =460 N/mm2 for the reinforcement and f cu = 30 N/mm2
for the concrete.
1
Verification Example
2
BS8110-97-1
-----------------------------------------------------------------
MIDAS/Gen - RC-Beam Checking [ BS8110-97 ]
=======================================
*.PROJECT :
*.DESIGN CODE : BS8110-97, *.UNIT SYSTEM : KN, mm
*.MEMBER : Member Type = BEAM, MEMB = 1
*.REINFORCEMENT PATTERN :
-----------------------------------------------------------------
Location i di( mm.) Rebar Asi( mm^2.)
-----------------------------------------------------------------
Top 1 50.000 2-P20 628.40000
Bottom 2 510.000 5-P25 2454.50000
-----------------------------------------------------------------
Stirrups : P10
======================================================
[[[*]]] ANALYZE POSITIVE BENDING MOMENT CAPACITY.
=======================================================
3
Verification Example
4
BS8110-97-1
5
Verification Example
----------------------------------------------
MIDAS/Gen - RC-Beam Checking
===========================
*.MIDAS/Gen - RC-BEAM Analysis/Design Program.
*.PROJECT :
*.DESIGN CODE : BS8110-97, *.UNIT SYSTEM : KN, mm
*.MEMBER : Member Type = BEAM, MEMB = 1
*.REINFORCEMENT PATTERN :
---------------------------------------------------------------
Location i di( mm.) Rebar Asi( mm^2.)
---------------------------------------------------------------
Top 1 50.000 2-P20 628.40000
Bottom 2 510.000 5-P25 2454.50000
---------------------------------------------------------------
Stirrups : P10
===================================================
[[[*]]] ANALYZE POSITIVE BENDING MOMENT CAPACITY.
===================================================
6
BS8110-97-1
7
Verification Example
8
BS8110-97-1
Comparison of Results
Reference
9
BS8110-97-2
Title
Description
Determine the ultimate moment of resistance of the T-section shown in figure. The
characteristic strenghth are f y =460 N/mm2 for the reinforcement and f cu = 30 N/mm2 for
the concrete.
1
Verification Example
Assume initially that the stress block depth lies within the flange and the reinforcement is
strained to the yield, so that f st = 0.87 f y
For no resultant axial force on the sections
Fst = Fcc
therefore
0.45 f cu b f s = 0.87 f y As
and solving for the depth of stress block
0.87 460 1472.7
s=
0.45 30 800
=54.57 mm
x = s / 0.9 = 60.64 mm
Hence the stress block does lie within the flange and with this depth of neutral axis the steel
will have yielded as assumed.
Lever arm:
z = d s/2
= 420 54.57 / 2 = 392.72 mm
Taking moments about the centroid of the reinforcement the moment of resistance is
M = Fcc z
= 0.45 f cu b f sz
= 0.45 30 800 54.57 392.72 10 6
= 231.46 kN m
2
BS8110-97-2
-----------------------------------------------------------------
MIDAS/Gen - RC-Beam Design < BS8110-97 >
=======================================
*.PROJECT :
*.DESIGN CODE : BS8110-97, *.UNIT SYSTEM : KN, mm
*.MEMBER : Member Type = BEAM, MEMB = 1
*.REINFORCEMENT PATTERN :
---------------------------------------------------------------
Location i di( mm.) Rebar Asi( mm^2.)
---------------------------------------------------------------
Top 1 50.000 2-P25 981.80000
Bottom 2 420.000 3-P25 1472.70000
---------------------------------------------------------------
Stirrups : P10
=======================================================
<<<*>>> ANALYZE POSITIVE BENDING MOMENT CAPACITY.
========================================================
3
Verification Example
4
BS8110-97-2
5
Verification Example
------------------------------------------
MIDAS/Gen - RC-Beam Design
========================
*.PROJECT :
*.DESIGN CODE : BS8110-97, *.UNIT SYSTEM : KN, mm
*.MEMBER : Member Type = BEAM, MEMB = 1
*.REINFORCEMENT PATTERN :
---------------------------------------------------------
Location i di( mm.) Rebar Asi( mm^2.)
---------------------------------------------------------
Top 1 50.000 2-P25 981.80000
Bottom 2 420.000 3-P25 1472.70000
---------------------------------------------------------
Stirrups : P10
===================================================
[[[*]]] ANALYZE POSITIVE BENDING MOMENT CAPACITY.
====================================================
( ). Compute design parameter (alpha1, beta1).
-. alpha1 = 0.6700
-. beta1 = 0.9000
( ). Check area of tensile reinforcement (Tee-beam).
6
BS8110-97-2
7
Verification Example
8
BS8110-97-2
Comparison of Results
Reference
9
BS8110-97-3
Title
Description
The T-section beam shown in figure is required to resist an ultimate design moment of 180
kN m. The characteristic material strengths are f y =460 N/mm2 and f cu =30 N/mm2.
Calculate the area of reinforcement required.
1
Verification Example
In the figure
Fcf is the force developed in the flange
Fcw is the force developed in the area of web in compression
Moment of resistance, M f , of the flange is
M f = Fcf + z1
or
M f = 0.45 f cu b f h f (d h f 2)
= 0.45 30 400 100(350 100 / 2) 106
= 162 kN m < 180 kN m, the design moment
Therefore, the stress block must extend below the flange.
It is now necessary to determine the depth, sw, of the web in compression,
where sw = s h f
For equilibrium:
Applied moment
184.22 = Fcf z1 + Fcw z2
= 162 + 0.45 f cu bw sw z2
This equation can be rearranged into
sw2 500sw + 13.33 103 = 0
Solving this quadratic equation
sw = 28
So that the depth of neutral axis
x = s / 0.9 = (100 + 28) / 0.9
= 142 mm
As x < d / 2 , compression reinforcement is not required.
For the equilibrium of the section
Fst = Fcf + Fcw
or
0.87 f y As = 0.45 f cu b f h f + 0.45 f cu bsw sw
0.87 460 As = 0.45 30(400 100 + 200 28)
2
BS8110-97-3
Therefore
636 103
As =
0.87 460
= 1540 mm2
3
Verification Example
----------------------------------------------------------------
MIDAS/Gen - RC-Beam Design [ BS8110-97 ]
======================================
*.PROJECT :
*.DESIGN CODE : BS8110-97, *.UNIT SYSTEM : KN, mm
*.MEMBER : Member Type = BEAM, MEMB = 1
*.REINFORCEMENT PATTERN :
--------------------------------------------------------------
Location i di( mm.) Rebar Asi( mm^2.)
--------------------------------------------------------------
Top 1 50.000 2-P32 1608.40000
Bottom 2 350.000 2-P32 1608.40000
--------------------------------------------------------------
Stirrups : P10
=====================================================
[[[*]]] ANALYZE POSITIVE BENDING MOMENT CAPACITY.
======================================================
4
BS8110-97-3
5
Verification Example
6
BS8110-97-3
7
Verification Example
------------------------------------------
MIDAS/Gen - RC-Beam Design
=========================
*.PROJECT :
*.DESIGN CODE : BS8110-97, *.UNIT SYSTEM : KN, mm
*.MEMBER : Member Type = BEAM, MEMB = 1
*.REINFORCEMENT PATTERN :
---------------------------------------------------------
Location i di( mm.) Rebar Asi( mm^2.)
---------------------------------------------------------
Top 1 50.000 2-P32 1608.40000
Bottom 2 350.000 2-P32 1608.40000
---------------------------------------------------------
Stirrups : P10
=====================================================
[[[*]]] ANALYZE POSITIVE BENDING MOMENT CAPACITY.
======================================================
8
BS8110-97-3
9
Verification Example
10
BS8110-97-3
11
Verification Example
Comparison of Results
Reference
12
BS8110-97-4
Title
Description
Determine the ultimate moment of resistance of the T-beam section shown in figure, given
f y =460 N/mm2 and f cu =30 N/mm2.
1
Verification Example
2
BS8110-97-4
----------------------------------------------------------------
MIDAS/Gen - RC-Beam Design [ BS8110-97 ]
======================================
*.PROJECT :
*.DESIGN CODE : BS8110-97, *.UNIT SYSTEM : KN, m
*.MEMBER : Member Type = BEAM, MEMB = 1
*.REINFORCEMENT PATTERN :
---------------------------------------------------------
Location i di( m.) Rebar Asi( m^2.)
---------------------------------------------------------
Top 1 0.050 2-P32 0.00161
Bottom 2 0.440 3-P32 0.00241
---------------------------------------------------------
Stirrups : P10
=====================================================
[[[*]]] ANALYZE POSITIVE BENDING MOMENT CAPACITY.
======================================================
3
Verification Example
4
BS8110-97-4
5
Verification Example
--------------------------------------------
MIDAS/Gen - RC-Beam Design
==========================
*.PROJECT :
*.DESIGN CODE : BS8110-97, *.UNIT SYSTEM : KN, mm
*.MEMBER : Member Type = BEAM, MEMB = 1
*.REINFORCEMENT PATTERN :
---------------------------------------------------------
Location i di( mm.) Rebar Asi( mm^2.)
--------------------------------------------------------------
Top 1 50.000 2-P32 1608.40000
Bottom 2 440.000 3-P32 2412.60000
--------------------------------------------------------------
Stirrups : P10
===================================================
[[[*]]] ANALYZE POSITIVE BENDING MOMENT CAPACITY.
===================================================
6
BS8110-97-4
-. beta1 = 0.9000
----------------------------------------------------------------
MIDAS/Gen - RC-Beam Design [ BS8110-97 ]
======================================
7
Verification Example
8
BS8110-97-4
Comparison of Results
Reference
9
BS8110-97-5
Title
Description
Shear reinforcement is to be designed for the one-span beam. The characteristic strength of
the mild steel links is f yv =250 N/mm2 .
1
Verification Example
Theoretical Results(BS8110-97)
2
BS8110-5
Results by MIDAS/Gen
-----------------------------------------------------------------
MIDAS/Gen - RC-Beam Checking [ BS8110-97 ]
=====================================
*.MIDAS/Gen - RC-BEAM Analysis/Design Program.
*.REINFORCEMENT PATTERN :
---------------------------------------------------------
Location i di( mm.) Rebar Asi( mm^2.)
---------------------------------------------------------
Top 1 50.000 2-P20 628.40000
Bottom 2 550.000 2-P25 981.80000
---------------------------------------------------------
Stirrups : P10
================================
[[[*]]] ANALYZE SHEAR CAPACITY.
================================
3
Verification Example
Comparison of Results
Reference
4
BS8110-97-6
Title
Description
A braced column of 300x450 cross-section resists at the ultimate limits state an axial load
of 1700kN and end moments of 70 kN m and 10kN m causing double curvature about the
minor axis XX as shown in figure. The columns effective heights are lex =6.75 m and ley =
8.0 m and the characteristic material strengths f cu = 30 N/mm2 and f y = 460 N/mm2.
1
Verification Example
Theoretical Results
Slenderness ratios are
lex h = 6.75 0.3 = 22.5 > 15
ley b = 8.0 0.45 = 17.8 > 15
2
BS8110-97-6
Results by MIDAS/Gen
----------------------------------------------------------------
MIDAS/Gen - RC-Column Design [ BS8110-97 ]
======================================
*.PROJECT :
*.DESIGN CODE : BS8110-97, *.UNIT SYSTEM : KN, m
*.MEMBER : Member Type = COLUMN, MEMB =1, LCB = 1, POS = 1/2
=================================================================
[[[*]]] CACULATE SLENDERNESS RATIOS, MAGNIFIED FORCES/MOMENTS.
=================================================================
3
Verification Example
4
BS8110-97-6
5
Verification Example
6
BS8110-97-6
Comparison of Results
Result Reference MIDAS/Gen
Reference