Sunteți pe pagina 1din 7

3.

5 LUBRICATION

Apply the specified lubricants to the lubrication points as shown below.

Lubricant type Lubricant amount


Lubrication points
(Manufacturer) per point

Permalub BAN-5 Head/carriage unit 1 1.5 mm diameter ball


(Nippon Koyu)
Switching lever guide 1 3 mm diameter ball

FLOIL BG1319 Leveller roller (LR) ASSY 2 1 mm diameter ball


(Kanto Kasei)
CR guide rail (top face) 24 2 mm diameter ball
(Total of 9831 mg)
CR support chassis (top face) 24 2 mm diameter ball
(Total of 9831 mg)
CR support chassis 30 2 mm diameter ball
(inner side of rear upright edge) (Total of 12338 mg)
(inner side of front upright edge) 30 2 mm diameter ball
(Total of 12338 mg)
CR guide rail (bottom face) 6 1 mm diameter ball

Molykote EM-30LP Platen 3 1 mm diameter ball


(Dow Corning)
T1 paper pull-in roller L 2 1 mm diameter ball

T2 paper pull-in roller L 2 1 mm diameter ball

Head/carriage unit
Apply a 1.5 mm diameter ball of grease (Permalub BAN-5) to the lubrication point below.

CR guide rail

Apply grease here.

Switching lever

(3_115)
Head/carriage unit

3-5 Confidential
Switching lever guide
Apply a 3 mm diameter ball of grease (Permalub BAN-5) to the lubrication point below.

Switching lever guide

(3_117)

Apply grease here.

Leveller roller (LR) ASSY


Apply a 1 mm diameter ball of grease (FLOIL BG1319) to each of the lubrication points below.

Leveler roller (LR) ASSY

Apply grease to
these 2 points.

(3_120)

3-6 Confidential
CR guide rail and CR support chassis (top face)
Apply a 2 mm diameter ball of grease (FLOIL BG1319) to each of the 48 lubrication points
below.
Lubrication procedure
(1) Move the head/carriage unit to the left end of its travel.
(2) Before applying grease, wipe dust or dirt off the lubrication area with an alcohol soaked
cloth.
(3) Move the head/carriage unit from the left to the right ends of its travel to spread the applied
grease on the CR guide rail and chassis.

Home position of
Apply grease to CR guide rail head/carriage unit
these 24 points.
12.7

57.1

57.25 0.5
41.05 0.5
(3_118)
Apply grease to CR support chassis
these 24 points. (mm)

3-7 Confidential
CR support chassis (inner sides of the front and rear upright edges)
Apply a 2 mm diameter ball of grease (FLOIL BG1319) to each of the 60 lubrication points
below.
Lubrication procedure
(1) Move the head/carriage unit to the left end of its travel.
(2) Before applying grease, wipe dust or dirt off the lubrication area with an alcohol soaked
cloth.
(3) Move the head/carriage unit from the left to the right ends of its travel to spread the applied
grease on the CR support chassis.

Apply grease to
these 30 points

34.8 4.1

10.8 13.15

Apply grease to
these 30 points CR support
chassis

5.65 0.5

5.625 0.5 (mm)

(3_119)

3-8 Confidential
CR guide rail (bottom face)
Apply a 1 mm diameter ball of grease (FLOIL BG1319) to each of the lubrication points below.

Viewed from the bottom


CR support chassis

Apply
grease
to these
3 points. (Right)

3.0-4.0
0.5-1.0
35 1
22 1
3.0-4.0

20 1
30 1 40 1
50 1

Apply grease to CR guide rail


these 3 points.
(mm)

(3_116)

Platen
Apply a 1 mm diameter ball of grease (Molykote EM-30LP) to each of the lubrication points
below.

1.0-1.5

1.0-1.5
Apply grease to
these 3 points.

(mm)
Platen (Front)
(3_121)

3-9 Confidential
T1 paper pull-in roller L
Apply a 1 mm diameter ball of grease (Molykote EM-30LP) to each of the lubrication points
below.

(Rear)

T1 paper pull-in
gear
T1 paper pull-in
roller R

Rib
Lower cover

T1 paper
pull-in
Apply grease to roller L
these 2 points.

(3_122)

3-10 Confidential
T2 paper pull-in roller L
Apply a 1 mm diameter ball of grease (Molykote EM-30LP) to each of the lubrication points
below.

Viewed from the rear

LT cover

T2 paper pull-in
gear
T2 paper pull-in
roller R

Rib

T2 paper
Apply grease to pull-in
these 2 points. roller L

(3_064a)

3-11 Confidential

S-ar putea să vă placă și