Sunteți pe pagina 1din 1

RETAINABILITY-L14B

maximumTransmissionPower
Indoor coverage issue (Small cell , PICO , DOT , Hetnet)
pmBadCovEvalReport partOfSectorPower
Physical changes (Tilt , Azimuth , height of antenna)
Coverage issues pmRadioTbsPwrRestricted confOutputPower
Audit cell reselection parameters , Tune DL power related parameters (as mentioned beside)
pmBadCovSearchEvalReport crsGain
Check if there is scope of new site
pdschTypeBGain
maximumTransmissionPower
partOfSectorPower
pmErabRelAbnormalEnbActUeLos Radio Cause Tune related parameters (as mentioned beside) , Audit cell reselection parameters
UE Lost (UE unreachable)
Poor DL SINR (CQI) pmRadioUeRepCqiDistr , pmRadioUeRepCqiDistr2 confOutputPower
Physical optimization (Tilt , Azimuth , height of antenna) , also Identify overshooting cells causing interference in DL
crsGain
pdschTypeBGain
pmRadioRecInterferencePwr
Check Power control parameters , Features like IRC & UL FSS can help to reduce UL interference.
pmRadioRecInterferencePwrPucch pZeroNominalPucch
UL RSSI Check for Loose Connectors,Faulty Antenna(Tx & Rx antenna ports),VSWR alarms,Faulty TMA Connections/settings.
pmRadioRecInterferencePwrPrb1~100 pZeroNominalPusch
External interference (cable tv , repeaters (due to power leak issues) , airport , police communication system etc..)
pmSinrPucchDistr , pmSinrPuschDistr
HW and other causes Check HW issues , alarms , improper cabling , connector issues , DUS Board error
PCI confliction or confusion Audit PCI of near by sites , also check if there is overshooting cell creating conflict
maximumTransmissionPower
Indoor coverage issue (Small cell , PICO , DOT , Hetnet)
pmBadCovEvalReport partOfSectorPower
Physical changes (Tilt , Azimuth , height of antenna)
Coverage issues pmRadioTbsPwrRestricted confOutputPower
Audit cell reselection parameters , Tune DL power related parameters (as mentioned beside)
pmBadCovSearchEvalReport crsGain
Check if there is scope of new site
pdschTypeBGain
maximumTransmissionPower
partOfSectorPower
Tune related parameters (as mentioned beside) , Audit cell reselection parameters
Poor DL SINR (CQI) pmRadioUeRepCqiDistr , pmRadioUeRepCqiDistr2 confOutputPower
Physical optimization (Tilt , Azimuth , height of antenna) also Identify overshooting cells causing interference in DL
crsGain
pdschTypeBGain
pmRadioRecInterferencePwr
Check Power control parameters , Features like IRC & UL FSS can help to reduce UL interference.
pmRadioRecInterferencePwrPucch pZeroNominalPucch
UL RSSI Check for Loose Connectors,Faulty Antenna(Tx & Rx antenna ports),VSWR alarms,Faulty TMA Connections/settings.
pmRadioRecInterferencePwrPrb1~100 pZeroNominalPusch
External interference (cable tv , repeaters (due to power leak issues) , airport , police communication system etc..)
pmSinrPucchDistr , pmSinrPuschDistr
Alarms Alarm need to monitor , some alarms need to monitor are VswrOverThreshold , Serviceunavailable (S1 connection failure) , Gigabit Ethernet Link Faul
Configuration issues ensure proper configuration , especially for all new site which are integrated recently
Ensure the eNodeB structure of the restart, MPBaseband or RRU
eNodeB Cause Auto Restart
pmCellDowntimeAuto lh all llog -l (do complete eNB health checkup)
pmErabRelAbnormalEnbActHo Cell Down Auto
(handover execution failure) pmCellDownLockAuto Baseband Startup issue Baseband Trace can be used , te enable all bbmcBbOmMeSwU
Cell down
Transport Cause S1 issues pmErabRelAbnormalEnbActTnFail check for alarms like Service Unavailable(S1 connection failure)
EPC Cause check for alarms like Service Unavailable(S1 connection failure) , Ip packet loss "above" SGW
pmCellDowntimeMan manually locked during network configuration issues ((eg. adding/changing/removing hardware)
Cell Down Manually Operation Cause
pmCellDownLockMan manually locked during parameter change (eg. activate feature)
pmRaAttCbra
pmRaSuccCbra
HW issues & Alarms Availability pmRaFailCbraMsg2Disc
pmRaAttCfra
pmRaSuccCfra Verify symtoms for sleeping cell
Sleeping Cell pmRaFailCfraMsg2Disc
pmRaAllocCfra
pmRrcConnEstabAtt
pmRrcConnSucc
Catch Trace(Baseband) trace from MSG1 to MSG5 , verify symtoms for sleeping cells
Power setting issue Check SectorEquipmentFunction:ConfiguredOutputPower & Eutrancelltdd:partOfSectorPower
Configuration issue
pmErabRelAbnormalEnb , pmErabRelAbnormalEnbQci Non-access issue Idle mode parameter issue Check Eutrancelltdd MO cell selection and reselection parameters & 3G&2G cell reselection parameter/feature
pmErabRelAbnormalEnbArp , pmErabRelNormalEnb Operation issues Cell Barred Check Cell Barred , acBarring for different scenarios
pmErabRelNormalEnbQci ,pmErabRelNormalEnbArp
eNodeB Initiated mErabRelNormalEnbUserInactivity , pmErabRelNormalEnbAct
HW issues Check HW issues , alarms , improper cabling , connector issues , DUS Board error
pmErabRelNormalEnbActArp , pmErabRelNormalEnbActQci capacityUnitConnectedUsers Check "licenseCapacityConnectedUsers" of Target cell
pmHoPrepRejInLicConnUsers
pmErabRelAbnormalEnbAct , pmErabRelNormalEnbUserInactivityQci gracePeriodTimeLeft Also Graceperiod should be noticed to exceed the licensed capacity limits for a limited periodof timeOffload traffic from target cel
Handover Failure License issue: pmHoPrepRejInLicMob Audit licenseState,featurestate,servicestate & other paramter related to Intra freq & Inter freq HO feature

Retainability
pmHoPrepRejInLicMultiErab Audit licenseState,featurestate,servicestate & other paramter related to MultiErabsPerUser feature
SARR(Session Abnormal Release Rate)
pmHoPrepRejInLicRlcUm Audit licenseState,featurestate,servicestate & other paramter related to RlcUm feature
LTE KPI Check these counters on target cell , Reduce no. of HO by physical opti or features (UE Level Oscillating Handover Minimization & Automated Mobility Optimization)
pmHoPrepRejInHighLoad (MP load control) MP capacity of DUS is higher than DUL , to increase MP capacity DUL can be replaced by DUS
Load:
pmHoPrepRejInOverload (procedure latency supervision) Physical changes (Tilt , Azimuth , height of antenna) to offload traffic from target cell
Offload Target cell Load by changing Layering strategy, Idle mode cellreselection, connected mode mobility & Load balancing parameters
Legend: Admission reject pmHoPrepRejInBearerAdmissionRej
dlTransNwBandwidth , ulTransNwBandwidth Audit UE Admission Control,Bearers (SRB & DRB) Admission Control,Transport Network Admission Control & Emergency call prioritization
zzzTemp20 , zzzTemp21 , pmRrcConnMax , pmRrcConnLevSum Physical changes (Tilt , Azimuth , height of antenna) to offload traffic from target cell
Check configuration issues (especially after new site is integrated)
Counters Configuration issue (check MO ExternalEUtranCellTDD,EUtranCellRelation,TermPointToENB,TermPointToMme)
(also check config para ex. Activeplmnlist,PCI , TAC , EutranFrequencyRef , IP address of TermPointToENB & MME)
Parameter Configuration issues ensure proper configuration , especially for all new site which are integrated recently
Ensure the eNodeB structure of the restart, MPBaseband or RRU
Action plan pmCellDowntimeAuto
eNodeB Cause Auto Restart
lh all llog -l (do complete eNB health checkup)
Cell Down Auto
pmCellDownLockAuto Baseband Startup issue Baseband Trace can be used , te enable all bbmcBbOmMeSwU
Cell down
pmErabRelAbnormalEnbActHpr Transport Cause S1 issues pmErabRelAbnormalEnbActTnFail check for alarms like Service Unavailable(S1 connection failure)
(handover preparation failure) EPC Cause check for alarms like Service Unavailable(S1 connection failure) , Ip packet loss "above" SGW
pmCellDowntimeMan manually locked during network configuration issues ((eg. adding/changing/removing hardware)
Cell Down Manually Operation Cause
pmCellDownLockMan manually locked during parameter change (eg. activate feature)
pmRaAttCbra
pmRaSuccCbra
Availability pmRaFailCbraMsg2Disc
pmRaAttCfra
Other checks pmRaSuccCfra Verify symtoms for sleeping cell
Sleeping Cell pmRaFailCfraMsg2Disc
pmRaAllocCfra
pmRrcConnEstabAtt
pmRrcConnSucc
Catch Trace(Baseband) trace from MSG1 to MSG5 , verify symtoms for sleeping cells
Power setting issue Check SectorEquipmentFunction:ConfiguredOutputPower & Eutrancelltdd:partOfSectorPower
Configuration issue
Non-access issue Idle mode parameter issue Check Eutrancelltdd MO cell selection and reselection parameters & 3G&2G cell reselection parameter/feature
Operation issues Cell Barred Check Cell Barred , acBarring for different scenarios
Alarms Check related alarms like Serviceunavailable (S1 connection failure,Hardware failure,GeneralHwError,GeneralSwError,Gigabit Ethernet Link Fault
MME pool If MME pool is different at source and target then HO-Preparation fail will be 100%, command "get . termpointmme" can be used to find out the MME pool IP
Target cell Target cell is prelaunch cell.(Primaryplmnreserved)
Intra LTE cellIndividualOffsetEUtran ; a3offset ; hysteresisA3 ; timeToTriggerA3
Inter freq LTE a5Threshold1RSRP ; a5Threshold2RSRP ; hysteresisA5 ; timeToTriggerA5 , a2TresholdRsrpPrim , ANR parameters
Tune HO related parameters
IRAT a2TresholdRsrpPrim ; hysteresisA2Prim ; timeToTriggerA2Prim ; b2Threshold1Rsrp ; b2Threshold2RscpUtra ; hysteresisB2 ; timeToTriggerB2
MCPC feature para a1a2SearchThresholdRsrp ; hysteresisA1A2SearchRsrp ; timeToTriggerA2Search ; a2CriticalThresholdRsrp ; hysteresisA2CriticalRsrp ; timeToTriggerA2Critical
Transport nw Issue pmErabRelAbnormalEnbActTnFail S1 or X2 interfaces DOWN (Transport Resource Unavailable) , Also check 3G collocated nodeb in term of SCTP LOSS
pmErabRelAbnormalEnbActCd Check any planned activities , Check high temperature on DU,RU bord also Check eNodeb alarm logs , also it may be do to common transport network
eNodeB Issue
HW and other causes Check HW issues , alarms , improper cabling , connector issues , DUS Board error
dlMaxRetxThreshold
Parameters RLC layer retransmissions
ulMaxRetxThreshold
Other important parameters/features
Multi-Target RRC Connection Re-Establishment
Features
Mobility Control at Poor Coverage
If MME related issue is their many sites in the NW will be impacted & if Core related issues is there all sectors of site will be impacted.
pmErabRelMmeActEutra If issue is in single sector then mostly it will be case of HW or radio related issues, Check HW issues , alarms , improper cabling , connector issues
(Release due to Eutran generated reason) Check Radio Condition (low coverage , UL_Pathloss, NOISE_PUSCH/PUCCH) (refer radio cases above) also Check Traffic Volume , also check if there is sudden spike in traffic)
pmErabRelMme , pmErabRelMmeArp Check if multi target RRC connection reestablishment feature is functioning properly.
pmErabRelMmeAct , pmErabRelMmeHo
Check is required on both Radio & core side
MME Initiated pmErabRelMmeActHo , pmErabRelAbnormalMmeAct
If MME related issue is their many sites in the NW will be impacted & if Core related issues is there all sectors of site will be impacted.
pmErabRelAbnormalMMeActQci , pmErabRelAbnormalMMeActArp
pmErabRelMmeActUnspecified If issue is in single sector then mostly it will be case of HW or radio related issues (check following) , Check HW issues , alarms , improper cabling , connector issues
pmErabRelMmeQci
Check Radio Condition (low coverage , UL_Pathloss, NOISE_PUSCH/PUCCH) (refer radio cases above) also Check Traffic Volume , also check if there is sudden spike in traffic)
If there is no issue on eNB side , core team should troubleshoot the issue , Traces at core side can help to do RCA
pmErabRelMmeActUserInactivity Release due to long UE inactivity

EGI-Network Engineering- LRAN

S-ar putea să vă placă și