Documente Academic
Documente Profesional
Documente Cultură
Sanitary Valves
steam systems. The sanitary design follows ASME BPE
guidelines including a 20Ra in internal finish, self-
draining design, and all relevant materials, marking
and documentation guidelines.
The MK93 has been specifically designed to provide
higher flow rates at low pressures and low subcooling
levels. In lab testing, the MK93 consistently exhib-
ited excellent flow rates at subcooling levels of less
than 3F or less (<1,7C). Note: Low subcooling op-
eration insures that condensate wont back up and wet
(cool) the upstream validated temperature sensor.
There are two base designs within the MK93 product
range: the standard MK93 good for differential pres-
sures up to 50 psi (3,4 bar), and the MK93 Option P
for DPs ranging from 45 90 psi (3,1 6,2 bar). Both
designs are rated to 90 psi (6,2 bar) operating pres-
sure but are recommended for use within the specified
differential pressure ratings.
During start-up, the bellows element is contracted and
fully open to discharge all non-condensable gas and New design provides excellent flow rates
condensate. The heat of entering steam causes the with low subcooling
element to expand, closing the valve. As condensate FDA and USP Class VI TFE-VIT gasket stan-
accumulates in the body, the element cools, causing dard on clamped body, or FDA and USP
the bellows/stem tip to retract allowing condensate to Class o-ring on bolted option
drain. Option for electropolished body
Body Inlet/Outlet: 316L Stainless Steel 10F 490 813 1142 1715 2207 2437
lbs/hr (1080) (1792) (2518) (3781) (4866) (5373)
Thermal Element: 316L Stainless Steel
20F 1127 1697 2202 3074 3932 4139
O-Ring-Gasket: Standard: Viton, Teflon Encapsulated lbs/hr (2485) (3741) (4855) (6777) (8669) (9125)
(FDA, USP Class VI approved); Optional: Tuff Steel or
Cold Water 2580 3648 4468 5768 6944 7504
SilverBack (others upon request) lbs/hr (5688) (8042) (9837) (12716) (15309) (16543)
Clamp: 304 SST (kgs/lbs)
Maximum Operating Conditions
Maximum Operating Pressure (PMO): 90 psig (6,2 bar) Dimensions
Maximum Allowable Temperature (TMA): 350F (177C)
Design Pressure/Temperature Rating Tri-Clamp Ends (1/2, 3/4
Maximum Allowable Pressure (PMA): 145 psig (10,0 bar)
Maximum Allowable Temperature (TMA): 350F (177C) Body
Inlet
Maximum Recommended Differential Pressure
MK93: 10 50 psi (0,7 3,4 bar) Clamp Gasket
MK93 Option P: 45 90 psi (3,1 6,2 bar)
CRN Registration Number: OC12623.5
2.6 (66,0)
Dimensions
Gasket
Clamp
4.03
(102,4) 4.2
(106,7)
Body
Outlet 1.65
2.02 (41,9)
(51,3)
Weight: 1.4 lbs (0,64 kgs) Weight: 1.5 lbs (0,68 kgs)
M K 9 3 Sanitary Steam Traps
Dimensions
A A
1.65
(41,9)
TYP
Horizontal Inlet/Vertical Outlet (CHCV) (1/2, 3/4)
A A
Section A-A
2.66 (67,6)
1.65
(41,9)
M K 9 3 Sanitary Steam Traps
Dimensions
A A
Section A-A
2.76 (70,1)
1.65
(41,9)
Bolted Body (93B) (1/2, 3/4) Welded Joint (93W) (1/2, 3/4)
2.50
(63,5)
1.71 (43,4)
2.61
(66,3)
2.59 (65,8)
Weight: 1.2 lbs (0,55 kgs) Weight: 1.0 lbs (0,45 kgs)
M K 9 3 Sanitary Steam Traps
Dimensions
2.6
(66,0)
2.6 (66,0)
1.6 2.1
(44,6) (53,3) 4.2(107)
Tri-Clamp
Tube Weld
4.2(107)
Threaded Ends
M K 9 3 Sanitary Steam Traps
316L material
suitable for clean
steam applications
Features & Benefits MK93 with Bolted Body with Tri-Clamp Ends
Standardized bellows
316L material suitable capsule assembly cannot
for clean steam applications be installed in the reverse
direction
Ordering Schematic
Steriflow Valve reserves the right to make revisions to its products, specifications, literature, and related information without notice.
Please visit our website at www.steriflowvalve.com for the latest information on our products.