Documente Academic
Documente Profesional
Documente Cultură
2012 ENGINE
Engine Assembly - TL
ENGINE REMOVAL
Special Tools Required
1. Disconnect the support struts from both sides of the pivot ball (bolted to the hood). Secure the hood in a
vertical position. Install the right side pivot ball into the lower threaded hole.
NOTE: Do not attempt to close the hood with the support strut in the vertical
position, as it will damage the support strut and hood.
Fig. 1: Installing Right Side Pivot Ball Into Lower Threaded Hole
Courtesy of AMERICAN HONDA MOTOR CO., INC.
manual
Tuesday, February 16, 2016 2:13:52
2:13:49 PM Page 1 2005 Mitchell Repair Information Company, LLC.
1
2012 Acura TL
2012 ENGINE Engine Assembly - TL
Fig. 2: Identifying Air Intake Duct Splash Separator And Related Components
Courtesy of AMERICAN HONDA MOTOR CO., INC.
manual
Tuesday, February 16, 2016 2:13:49 PM Page 2 2005 Mitchell Repair Information Company, LLC.
2
2012 Acura TL
2012 ENGINE Engine Assembly - TL
8. M/T model: Remove the harness clamps (C) from the battery base.
9. Remove the bolts (D), and loosen the bolt (E), then remove the battery base.
10. M/T model: Remove the harness clamp (A) and the ground cable (B), then disconnect the positive starter
cable (C).
manual
Tuesday, February 16, 2016 2:13:49 PM Page 3 2005 Mitchell Repair Information Company, LLC.
3
2012 Acura TL
2012 ENGINE Engine Assembly - TL
Fig. 4: Identifying Harness Clamp, Ground Cable And Positive Starter Cable
Courtesy of AMERICAN HONDA MOTOR CO., INC.
11. A/T model: Remove the harness clamps (A), then disconnect the positive starter cable (B).
manual
Tuesday, February 16, 2016 2:13:49 PM Page 4 2005 Mitchell Repair Information Company, LLC.
4
2012 Acura TL
2012 ENGINE Engine Assembly - TL
Fig. 6: Identifying Battery Cable From Under-Hood Fuse/Relay Box And Harness Clamp
Courtesy of AMERICAN HONDA MOTOR CO., INC.
16. Remove the harness clamp (A), then disconnect the ECM/PCM connectors (B).
manual
Tuesday, February 16, 2016 2:13:49 PM Page 5 2005 Mitchell Repair Information Company, LLC.
5
2012 Acura TL
2012 ENGINE Engine Assembly - TL
17. Remove the quick-connect fitting cover (A), then disconnect the fuel feed hose (B) (see FUEL
LINE/QUICK-CONNECT FITTING REMOVAL ).
18. Disconnect the brake booster vacuum hose (A) and the EVAP canister hose (B).
manual
Tuesday, February 16, 2016 2:13:49 PM Page 6 2005 Mitchell Repair Information Company, LLC.
6
2012 Acura TL
2012 ENGINE Engine Assembly - TL
19. M/T model: Remove the three bolts securing the shift cable holder, then remove the shift cable and the
select cable (see step 23 under TRANSMISSION REMOVAL ). Do not bend the cables excessively.
20. M/T model: Remove the clutch slave cylinder and the clutch line bracket mounting nut (see step 24 under
TRANSMISSION REMOVAL ). Do not operate the clutch pedal once the slave cylinder has been
removed.
21. A/T model: Remove the shift cable (see SHIFT CABLE REPLACEMENT ). Do not bend the shift
cable excessively.
22. Remove the drive belt (see DRIVE BELT REPLACEMENT ).
23. Disconnect the EPS connectors (A).
manual
Tuesday, February 16, 2016 2:13:50 PM Page 7 2005 Mitchell Repair Information Company, LLC.
7
2012 Acura TL
2012 ENGINE Engine Assembly - TL
25. Loosen the upper steering joint bolt (B) and the lower steering bolt (C).
26. Center the steering wheel spokes, and install a commercially available steering wheel holder tool (A).
27. Remove the lower steering joint bolt (A). Disconnect the steering joint (B) by sliding the steering joint
into the column shaft (C). Tighten the upper steering joint bolt (D) to hold the steering joint in place.
manual
Tuesday, February 16, 2016 2:13:50 PM Page 8 2005 Mitchell Repair Information Company, LLC.
8
2012 Acura TL
2012 ENGINE Engine Assembly - TL
NOTE: Do not disconnect the steering joint from the column shaft.
Fig. 14: Identifying Steering Joint, Column Shaft, Upper And Lower Steering Joint Bolt
Courtesy of AMERICAN HONDA MOTOR CO., INC.
28. Remove the center guide (A) (if equipped) from the top of the pinion shaft (B), and discard it.
29. Wrap vinyl tape over the splines on the pinion shaft.
30. Wait until the engine is cool, then carefully remove the radiator cap.
31. Raise the vehicle on the lift.
32. Remove the front wheels.
manual
Tuesday, February 16, 2016 2:13:50 PM Page 9 2005 Mitchell Repair Information Company, LLC.
9
2012 Acura TL
2012 ENGINE Engine Assembly - TL
33. Remove the front splash shield (see FRONT SPLASH SHIELD REPLACEMENT ).
34. Loosen the drain plug in the radiator, and drain the engine coolant (see COOLANT CHECK ).
35. Drain the transmission fluid:
Manual transmission (see TRANSMISSION FLUID INSPECTION AND REPLACEMENT )
Automatic transmission (see ATF REPLACEMENT )
36. Drain the engine oil (see ENGINE OIL LEVEL CHECK ).
37. Remove the damper fork (see step 4 under DAMPER/SPRING REMOVAL AND INSTALLATION ).
38. Separate the tie-rod end ball joints from the knuckles (see step 13 under RACK END REMOVAL AND
INSTALLATION ).
39. Separate the knuckles from the suspension lower arms (see step 7 under LOWER ARM
REMOVAL/INSTALLATION ).
40. Remove the driveshafts (see DRIVESHAFT INSPECTION ). Coat all precision-finished surfaces with
new engine oil. Tie plastic bags over the driveshaft ends.
41. Remove the front subframe stiffener.
manual
Tuesday, February 16, 2016 2:13:50 PM Page 10 2005 Mitchell Repair Information Company, LLC.
10
2012 Acura TL
2012 ENGINE Engine Assembly - TL
43. With SH-AWD: Remove the propeller shaft (see PROPELLER SHAFT REMOVAL ).
44. With SH-AWD: Remove the transfer assembly:
Manual transmission (see TRANSFER ASSEMBLY FLUID INSPECTION AND
REPLACEMENT )
Automatic transmission (see TRANSFER ASSEMBLY REMOVAL )
45. A/T model: Disconnect the ATF cooler hoses from the transmission, then plug the ATF cooler hoses and
the lines (see step 44 under TRANSMISSION REMOVAL ).
46. Lower the vehicle on the lift.
47. Disconnect the upper radiator hose (A) and the lower radiator hose (B).
manual
Tuesday, February 16, 2016 2:13:50 PM Page 11 2005 Mitchell Repair Information Company, LLC.
11
2012 Acura TL
2012 ENGINE Engine Assembly - TL
Fig. 20: Identifying A/C Compressor Clutch Connector And Harness Clamp With Mounting Bolts
Courtesy of AMERICAN HONDA MOTOR CO., INC.
51. Remove the A/C compressor without disconnecting the A/C hoses. Do not bend the A/C hoses
excessively.
manual
Tuesday, February 16, 2016 2:13:50 PM Page 12 2005 Mitchell Repair Information Company, LLC.
12
2012 Acura TL
2012 ENGINE Engine Assembly - TL
52. Remove the bolt (A) securing the connector bracket (B) from the front cylinder head; use the bracket bolt
hole (C) to attach the engine hanger balance bar front arm.
Fig. 21: Identifying Connector Bracket, Bracket Bolt Hole And Bolt
Courtesy of AMERICAN HONDA MOTOR CO., INC.
53. Remove the harness clamp (A), then remove the bolt (B) securing the engine mount control solenoid
valve bracket (C) from the rear cylinder head; use the bracket bolt hole (D) to attach the 2008 V6
attachment arm.
Fig. 22: Identifying Solenoid Valve Bracket, Harness Clamp, Bracket Bolt Hole, Vacuum Hose And
Bolt
Courtesy of AMERICAN HONDA MOTOR CO., INC.
manual
Tuesday, February 16, 2016 2:13:50 PM Page 13 2005 Mitchell Repair Information Company, LLC.
13
2012 Acura TL
2012 ENGINE Engine Assembly - TL
Fig. 23: Identifying Front Arm, Spacer, Bolts And Wing Nut
Courtesy of AMERICAN HONDA MOTOR CO., INC.
56. Install the engine support hanger (AAR-T1256) onto the vehicle as shown, and attach the hook to the
slotted hole in the engine hanger balance bar. Tighten the wing nut (F) by hand, and lift and support the
engine/transmission.
57. M/T model: Remove the front engine mount (see FRONT ENGINE MOUNT REMOVAL AND
INSTALLATION ).
58. A/T model: Disconnect the vacuum hose (A) and remove the front engine mount stop (B), then remove
the front engine mount bolt (C).
manual
Tuesday, February 16, 2016 2:13:50 PM Page 14 2005 Mitchell Repair Information Company, LLC.
14
2012 Acura TL
2012 ENGINE Engine Assembly - TL
Fig. 24: Identifying Vacuum Hose, Front Engine Mount Stop And Engine Mounting Bolt
Courtesy of AMERICAN HONDA MOTOR CO., INC.
59. M/T model: Remove the rear engine mount bolt (A).
60. A/T model: Remove the rear engine mount stop (A), then remove the rear engine mount bolt (B).
manual
Tuesday, February 16, 2016 2:13:50 PM Page 15 2005 Mitchell Repair Information Company, LLC.
15
2012 Acura TL
2012 ENGINE Engine Assembly - TL
Fig. 26: Identifying Rear Engine Mount Stop And Engine Mounting Bolts
Courtesy of AMERICAN HONDA MOTOR CO., INC.
manual
Tuesday, February 16, 2016 2:13:50 PM Page 16 2005 Mitchell Repair Information Company, LLC.
16
2012 Acura TL
2012 ENGINE Engine Assembly - TL
Fig. 28: Identifying Ground Cable And Lower Transmission Mount Nuts
Courtesy of AMERICAN HONDA MOTOR CO., INC.
Fig. 29: Identifying Subframe, Subframe Adapter, Belt And Belt Stop
Courtesy of AMERICAN HONDA MOTOR CO., INC.
66. Raise the transmission jack and line up the slots in the subframe adapter arms with the bolt holes on the
jack base, then securely attach them with four bolts.
67. Remove the four 12 x 1.25 mm bolts (A) securing the subframe stiffeners (B), the four subframe
mounting bolts (C), and the stiffeners, then lower the front subframe (D).
manual
Tuesday, February 16, 2016 2:13:50 PM Page 17 2005 Mitchell Repair Information Company, LLC.
17
2012 Acura TL
2012 ENGINE Engine Assembly - TL
Fig. 30: Identifying Front Subframe, Subframe Stiffeners, Subframe Mounting Bolts
Courtesy of AMERICAN HONDA MOTOR CO., INC.
Fig. 31: Identifying Chain Hoist, Engine Hanger And Transmission Hanger
Courtesy of AMERICAN HONDA MOTOR CO., INC.
manual
Tuesday, February 16, 2016 2:13:50 PM Page 18 2005 Mitchell Repair Information Company, LLC.
18
2012 Acura TL
2012 ENGINE Engine Assembly - TL
70. Remove the mounting bolts from the upper half of the side engine mount bracket.
NOTE: Do not remove the bolt (A) from the. upper transmission mount. If the bolt
is removed, the upper transmission mount must be replaced as an
assembly.
M/T model
A/T model
72. Check that the engine/transmission is completely free of the vacuum hoses, the fuel hoses, the coolant
hoses, and the electrical wiring.
73. Slowly lower the engine/transmission about 150 mm (6 in). Check once again that all the hoses and the
electrical wiring are disconnected and free from the engine/transmission, then lower it all the way and
support it.
74. Disconnect the chain hoist from the engine/transmission.
75. Raise the vehicle, and remove the engine/transmission from under the vehicle.
ENGINE INSTALLATION
Special Tools Required
1. Install the engine mount brackets and the accessory brackets and tighten their bolts to the specified
torque.
manual
Tuesday, February 16, 2016 2:13:50 PM Page 20 2005 Mitchell Repair Information Company, LLC.
20
2012 Acura TL
2012 ENGINE Engine Assembly - TL
Fig. 35: Identifying Engine Mount Brackets And Accessory Brackets With Torque Specifications
Courtesy of AMERICAN HONDA MOTOR CO., INC.
2. Position the engine/transmission under the vehicle. Be sure that they are properly aligned. Carefully
lower the vehicle until the engine/transmission are properly positioned in the engine compartment. Make
sure the vehicle is not resting on any part of the engine/transmission. Support the engine/transmission
with a chain hoist (A) and carefully raise the engine/transmission into place.
NOTE: Reinstall the mounting bolts/support nuts in the sequence given in the
following steps. Failure to follow this sequence may cause excessive
noise and vibration, and reduce engine mount life.
manual
Tuesday, February 16, 2016 2:13:50 PM Page 21 2005 Mitchell Repair Information Company, LLC.
21
2012 Acura TL
2012 ENGINE Engine Assembly - TL
3. Install the new mounting bolts into the upper half of the side engine mount bracket. Tighten the bolts to
the specified torque.
Fig. 37: Identifying Mounting Bolts Into Upper Half Of Side Engine Mount Bracket With Torque
Specifications
Courtesy of AMERICAN HONDA MOTOR CO., INC.
4. Tighten the new upper transmission mount bracket mounting bolts to the specified torque.
manual
Tuesday, February 16, 2016 2:13:50 PM Page 22 2005 Mitchell Repair Information Company, LLC.
22
2012 Acura TL
2012 ENGINE Engine Assembly - TL
NOTE: If bolt (A) was removed by mistake during removal, the upper transmission
mount bracket must be replaced as an assembly.
M/T model
Fig. 38: Identifying Bracket Mounting Bolts (M/T Model) With Torque Specifications
Courtesy of AMERICAN HONDA MOTOR CO., INC.
A/T model
Fig. 39: Identifying Bracket Mounting Bolts (A/T Model) With Torque Specifications
Courtesy of AMERICAN HONDA MOTOR CO., INC.
manual
Tuesday, February 16, 2016 2:13:50 PM Page 23 2005 Mitchell Repair Information Company, LLC.
23
2012 Acura TL
2012 ENGINE Engine Assembly - TL
5. Install the engine hanger balance bar (VSB02C000019). Attach the front arm (A) to the front cylinder
head with a 10 mm (0.39 in) spacer (B) and a 10 x 1.25 mm bolt (C). Remove the rear arm from the
engine hanger balance bar, then install the 2008 V6 attachment arm (SIL02C000033). Attach the 2008 V6
attachment arm to the rear cylinder head with a 10 mm (0.39 in) spacer (D) and an 8 x 1.25 mm bolt (E).
Fig. 40: Identifying Front Arm, Spacers And Bolts Of Engine Hanger Balance Bar
Courtesy of AMERICAN HONDA MOTOR CO., INC.
6. Install the engine support hanger (AAR-T1256) onto the vehicle as shown, and attach the hook to the
slotted hole in the engine hanger balance bar. Tighten the wing nut (F) by hand, and lift and support the
engine/transmission.
7. Remove the chain hoist, then raise the vehicle on the lift.
8. Attach the subframe adapter (VSB02C000016) to the subframe by looping the belt (A) over the front of
the front subframe (B), then secure the belt with its stop (C).
manual
Tuesday, February 16, 2016 2:13:50 PM Page 24 2005 Mitchell Repair Information Company, LLC.
24
2012 Acura TL
2012 ENGINE Engine Assembly - TL
9. Line up the slots in the subframe adapter arms with the bolt holes on the jack base, then securely attach
them with four bolts, then raise the front subframe up to the body.
10. Loosely install the new subframe mounting bolts (four) (A), the 12 x 1.25 mm bolts (two) (B), the new 12
x 1.25 mm (two) (C), and the stiffeners (D).
manual
Tuesday, February 16, 2016 2:13:50 PM Page 25 2005 Mitchell Repair Information Company, LLC.
25
2012 Acura TL
2012 ENGINE Engine Assembly - TL
11. Align the front subframe with the subframe alignment pin (see FRONT SUBFRAME ALIGNMENT ).
12. Remove the transmission jack and the front subframe adapter.
13. Tighten the bolts securing the subframe middle mount.
Fig. 43: Identifying Subframe Middle Mount & Bolts With Torque Specifications
Courtesy of AMERICAN HONDA MOTOR CO., INC.
Fig. 44: Identifying Lower Transmission Mount With Nuts And Ground Cable With Torque
Specifications
Courtesy of AMERICAN HONDA MOTOR CO., INC.
17. Remove the engine support hanger, the engine hanger balance bar, and the 2008 V6 attachment arm.
18. M/T model: Install the front engine mount (see FRONT ENGINE MOUNT REMOVAL AND
INSTALLATION ).
19. A/T model: Tighten the new front engine mount bolt (A), then install the front engine mount stop (B) and
connect the vacuum hose (C).
Fig. 45: Identifying Vacuum Hose, Front Engine Mounting Bolt And Engine Mount Stop (A/T
Model) With Torque Specifications
Courtesy of AMERICAN HONDA MOTOR CO., INC.
20. M/T model: Tighten the new rear engine mount bolt.
Fig. 46: Identifying Rear Engine Mount Bolt (M/T Model) With Torque Specifications
Courtesy of AMERICAN HONDA MOTOR CO., INC.
manual
Tuesday, February 16, 2016 2:13:50 PM Page 27 2005 Mitchell Repair Information Company, LLC.
27
2012 Acura TL
2012 ENGINE Engine Assembly - TL
21. A/T model: Tighten the new rear engine mount bolt (A), then install the rear engine mount stop (B) using
new nuts (C).
Fig. 47: Identifying Rear Engine Mount Bolt, Engine Mount Stop And Nuts (A/T Model) With
Torque Specifications
Courtesy of AMERICAN HONDA MOTOR CO., INC.
22. Loosen the mounting bolts for the upper half of the side engine mount bracket, then retighten them in the
numbered sequence shown.
manual
Tuesday, February 16, 2016 2:13:50 PM Page 28 2005 Mitchell Repair Information Company, LLC.
28
2012 Acura TL
2012 ENGINE Engine Assembly - TL
Fig. 48: Identifying Mounting Bolts Of Side Engine Mount Bracket With Torque Specifications
Courtesy of AMERICAN HONDA MOTOR CO., INC.
23. Loosen the mounting bolts for the upper transmission mount bracket, then retighten them to the specified
torque.
M/T model
Fig. 49: Identifying Mounting Bolts For Upper Transmission Mount Bracket (M/T Model) With
Torque Specifications
Courtesy of AMERICAN HONDA MOTOR CO., INC.
manual
Tuesday, February 16, 2016 2:13:50 PM Page 29 2005 Mitchell Repair Information Company, LLC.
29
2012 Acura TL
2012 ENGINE Engine Assembly - TL
A/T model
Fig. 50: Identifying Mounting Bolts For Upper Transmission Mount Bracket (A/T Model) With
Torque Specifications
Courtesy of AMERICAN HONDA MOTOR CO., INC.
Fig. 51: Identifying Connector Bracket To Front Cylinder Head With Torque Specifications
Courtesy of AMERICAN HONDA MOTOR CO., INC.
25. Install the engine mount control solenoid valve bracket to the rear cylinder head, then install the harness
clamp (A).
manual
Tuesday, February 16, 2016 2:13:50 PM Page 30 2005 Mitchell Repair Information Company, LLC.
30
2012 Acura TL
2012 ENGINE Engine Assembly - TL
Fig. 52: Identifying Harness Clamp And Vacuum Hose Of Engine Mount Control Solenoid Valve
Bracket With Torque Specifications
Courtesy of AMERICAN HONDA MOTOR CO., INC.
Fig. 53: Identifying Harness Clamp And Clutch Connector Of A/C Compressor With Torque
Specifications
manual
Tuesday, February 16, 2016 2:13:50 PM Page 31 2005 Mitchell Repair Information Company, LLC.
31
2012 Acura TL
2012 ENGINE Engine Assembly - TL
30. Connect the upper radiator hose (A) and the lower radiator hose (B).
34. With SH-AWD: Install the propeller shaft (see PROPELLER SHAFT INSTALLATION ).
35. Install exhaust pipe A using new gaskets (6) and new self-locking nuts (C).
Fig. 56: Identifying Exhaust Pipe, Gaskets And Self-Locking Nuts With Torque Specifications
Courtesy of AMERICAN HONDA MOTOR CO., INC.
36. Install the front subframe stiffener (A) using new bolts (B).
manual
Tuesday, February 16, 2016 2:13:50 PM Page 33 2005 Mitchell Repair Information Company, LLC.
33
2012 Acura TL
2012 ENGINE Engine Assembly - TL
Fig. 57: Identifying Front Subframe Stiffener And Bolts With Torque Specifications
Courtesy of AMERICAN HONDA MOTOR CO., INC.
37. Install a new set ring on the end of each driveshaft, then install the driveshafts (see FRONT
DRIVESHAFT INSTALLATION ). Make sure each ring "clicks" into place in the differential and the
intermediate shaft.
38. Connect the suspension lower arm to the knuckles (see step 7 under LOWER ARM
REMOVAL/INSTALLATION ).
39. Connect the tie-rod end ball joints to the knuckles (see step 42 under STEERING GEARBOX
REMOVAL AND INSTALLATION ).
40. Install the damper fork (see step 4 under DAMPER/SPRING REMOVAL AND INSTALLATION ).
41. Install the front splash shield (see FRONT SPLASH SHIELD REPLACEMENT ).
42. Install the front wheels.
43. Lower the vehicle on the lift.
44. Loosen the upper steering joint bolt (A), and slip the lower end of the steering joint (B) onto the pinion
shaft (C).
Fig. 58: Identifying Pinion Shaft, Steering Joint, Groove, Bolt Hole, Upper And Lower Steering
Joint Bolt
Courtesy of AMERICAN HONDA MOTOR CO., INC.
45. Align the bolt hole (D) on the steering joint with the groove (E) around the pinion shaft, then loosely
install the lower steering joint bolt (F). Be sure that the joint bolt is securely in the groove in the pinion
shaft.
46. Remove the steering wheel holder tool (A).
manual
Tuesday, February 16, 2016 2:13:50 PM Page 34 2005 Mitchell Repair Information Company, LLC.
34
2012 Acura TL
2012 ENGINE Engine Assembly - TL
47. Tighten the upper and lower steering joint bolts (A) to the specified torque.
Fig. 60: Identifying Steering Joint Cover, Upper And Lower Steering Joint Bolts With Torque
Specifications
Courtesy of AMERICAN HONDA MOTOR CO., INC.
manual
Tuesday, February 16, 2016 2:13:50 PM Page 35 2005 Mitchell Repair Information Company, LLC.
35
2012 Acura TL
2012 ENGINE Engine Assembly - TL
51. A/T model: Install the shift cable (see SHIFT CABLE REPLACEMENT ).
52. M/T model: Install the clutch slave cylinder and the clutch line bracket mounting bolt (see step 49 under
TRANSMISSION INSTALLATION ).
53. M/T model: Install the shift cable and the select cable, then tighten the three bolts securing the shift cable
holder (see step 50 under TRANSMISSION INSTALLATION ).
54. Connect the brake booster vacuum hose (A) and the EVAP canister hose (B).
Fig. 62: Identifying Brake Booster Vacuum Hose And EVAP Canister Hose
Courtesy of AMERICAN HONDA MOTOR CO., INC.
55. Connect the fuel feed hose (A), then install the quick-connect fitting cover (B) (see FUEL
LINE/QUICK-CONNECT FITTING INSTALLATION ).
manual
Tuesday, February 16, 2016 2:13:50 PM Page 36 2005 Mitchell Repair Information Company, LLC.
36
2012 Acura TL
2012 ENGINE Engine Assembly - TL
Fig. 63: Identifying Fuel Feed Hose And Quick-Connect Fitting Cover
Courtesy of AMERICAN HONDA MOTOR CO., INC.
56. Connect the ECM/PCM connectors (A), then install the harness clamp (B).
57. Connect the harness connectors (A), then install the harness clamp (B).
manual
Tuesday, February 16, 2016 2:13:50 PM Page 37 2005 Mitchell Repair Information Company, LLC.
37
2012 Acura TL
2012 ENGINE Engine Assembly - TL
59. Connect the battery cable (B) to the under-hood fuse/relay box.
60. Install the strut brace (see FRAME BRACE REPLACEMENT ).
61. M/T model: Connect the positive starter cable (A), then install the harness clamp (B). Make sure the
crimped side of the ring terminal face away from the starter when you connect it.
manual
Tuesday, February 16, 2016 2:13:50 PM Page 38 2005 Mitchell Repair Information Company, LLC.
38
2012 Acura TL
2012 ENGINE Engine Assembly - TL
Fig. 67: Identifying Positive Starter Cable, Harness Clamp And Ground Cable (M/T Model) With
Torque Specifications
Courtesy of AMERICAN HONDA MOTOR CO., INC.
Fig. 68: Identifying Positive Starter Cable, Harness Clamps (A/T Model) With Torque
Specifications
Courtesy of AMERICAN HONDA MOTOR CO., INC.
manual
Tuesday, February 16, 2016 2:13:50 PM Page 39 2005 Mitchell Repair Information Company, LLC.
39
2012 Acura TL
2012 ENGINE Engine Assembly - TL
64. Install the battery base (A), then install the harness clamp (B).
Fig. 69: Identifying Battery Base And Harness Clamps With Torque Specification (M/T Model)
With Torque Specifications
Courtesy of AMERICAN HONDA MOTOR CO., INC.
Fig. 70: Identifying Air Intake Duct Splash Separator With Mounting Bolts
Courtesy of AMERICAN HONDA MOTOR CO., INC.
manual
Tuesday, February 16, 2016 2:13:50 PM Page 40 2005 Mitchell Repair Information Company, LLC.
40
2012 Acura TL
2012 ENGINE Engine Assembly - TL
69. Inspect for fuel leaks. Turn the ignition switch to ON (II), or press the engine start/stop button to select
the ON mode (do not operate the starter) so the fuel pump runs for about 2 seconds and pressurizes the
fuel line. Repeat this operation three times, then check for fuel leaks at any point in the fuel line.
70. Refill the engine with engine oil (see ENGINE OIL LEVEL CHECK ).
71. Refill the transmission with fluid:
Manual transmission (see TRANSMISSION FLUID INSPECTION AND REPLACEMENT )
Automatic transmission (see ATF REPLACEMENT )
72. M/T model: Check that the transmission shifts into all gears smoothly.
73. A/T model: Move the shift lever to each gear, and verify that the A/T gear position indicator follows the
transmission range switch.
74. Refill the radiator with engine coolant, and bleed the air from the cooling system (see COOLANT
CHECK ).
75. Check for fluid leaks.
76. Do the ECM/PCM reset procedure (see HDS CLEAR COMMAND ).
77. Do the CKP pattern clear/CKP pattern learn procedure (see CKP PATTERN CLEAR/CKP PATTERN
LEARN ).
78. Inspect the idle speed (see IDLE SPEED INSPECTION ).
79. Inspect the ignition timing (see IGNITION TIMING INSPECTION ).
80. Install the engine compartment covers (see ENGINE COMPARTMENT COVER REPLACEMENT ).
81. Check the wheel alignment (see WHEEL ALIGNMENT ).
manual
Tuesday, February 16, 2016 2:13:50 PM Page 41 2005 Mitchell Repair Information Company, LLC.
41
2012 Acura TL
2012 ENGINE Engine Assembly - TL
Fig. 71: Identifying Ground Cable And Engine Mount Bracket With Mounting Bolts
Courtesy of AMERICAN HONDA MOTOR CO., INC.
INSTALLATION
manual
Tuesday, February 16, 2016 2:13:50 PM Page 42 2005 Mitchell Repair Information Company, LLC.
42
2012 Acura TL
2012 ENGINE Engine Assembly - TL
Fig. 73: Identifying Side Engine Mount & Bolts With Torque Specifications
Courtesy of AMERICAN HONDA MOTOR CO., INC.
2. Loosely install the upper half of the side engine mount bracket (A) using new bolts.
Fig. 74: Identifying Engine Mount Bracket, Ground Cable And Tightening Sequence Of Bolts With
Torque Specifications
Courtesy of AMERICAN HONDA MOTOR CO., INC.
manual
Tuesday, February 16, 2016 2:13:50 PM Page 43 2005 Mitchell Repair Information Company, LLC.
43
2012 Acura TL
2012 ENGINE Engine Assembly - TL
Fig. 75: Identifying Front Engine Mount Stop And Front Engine Mount Bolt
Courtesy of AMERICAN HONDA MOTOR CO., INC.
manual
Tuesday, February 16, 2016 2:13:50 PM Page 44 2005 Mitchell Repair Information Company, LLC.
44
2012 Acura TL
2012 ENGINE Engine Assembly - TL
Fig. 76: Identifying Front Engine Mount Mounting Bolts And Vacuum Hose
Courtesy of AMERICAN HONDA MOTOR CO., INC.
5. Lift and support the engine with a jack and a wood block under the engine/transmission.
6. Remove the front engine mount and disconnect the vacuum hose (B).
NOTE: A/T model: Do not bend the ATF cooler pipe when removing the front
engine mount.
INSTALLATION
1. Connect the vacuum hose (A), then align the front engine mount with its mounting holes and install the
new front engine mount mounting bolts (B).
NOTE: A/T model: Do not bend the ATF cooler pipe when installing the front
engine mount.
manual
Tuesday, February 16, 2016 2:13:50 PM Page 45 2005 Mitchell Repair Information Company, LLC.
45
2012 Acura TL
2012 ENGINE Engine Assembly - TL
Fig. 77: Identifying Vacuum Hose, Front Engine Mount Mounting Bolts With Torque
Specifications (A/T Model)
Courtesy of AMERICAN HONDA MOTOR CO., INC.
Fig. 78: Identifying Front Engine Mount Bolt And Front Engine Mount Stop With Torque
Specifications
Courtesy of AMERICAN HONDA MOTOR CO., INC.
manual
Tuesday, February 16, 2016 2:13:50 PM Page 46 2005 Mitchell Repair Information Company, LLC.
46
2012 Acura TL
2012 ENGINE Engine Assembly - TL
5. Install the engine compartment covers (see ENGINE COMPARTMENT COVER REPLACEMENT ).
Fig. 79: Identifying Harness Clamp, Harness Connectors On Left Strut Tower
Courtesy of AMERICAN HONDA MOTOR CO., INC.
7. Remove the two harness clamps (A) and the brake booster vacuum hose clamp (B) from the under-hood
fuse/relay box mounting bracket (C).
manual
Tuesday, February 16, 2016 2:13:50 PM Page 47 2005 Mitchell Repair Information Company, LLC.
47
2012 Acura TL
2012 ENGINE Engine Assembly - TL
Fig. 80: Identifying Harness Clamp, Brake Booster Vacuum Hose Clamp And Mounting Bracket
Courtesy of AMERICAN HONDA MOTOR CO., INC.
8. Remove the mounting bolt (A) and the two mounting nuts (B) from the under-hood fuse/relay box
mounting bracket, then tilt the under-hood fuse/relay box forward.
13. Remove the two rear engine mount bracket mounting bolts (A).
17. Remove the rear engine mount mounting bolt (B), then remove the two rear engine mount bracket
mounting bolts (C).
manual
Tuesday, February 16, 2016 2:13:50 PM Page 49 2005 Mitchell Repair Information Company, LLC.
49
2012 Acura TL
2012 ENGINE Engine Assembly - TL
18. Remove the rear engine mount bracket (A) from the top by sliding it out, and lifting it out from the
driver's side.
manual
Tuesday, February 16, 2016 2:13:50 PM Page 50 2005 Mitchell Repair Information Company, LLC.
50
2012 Acura TL
2012 ENGINE Engine Assembly - TL
INSTALLATION-M/T MODEL
2. Align the rear engine mount with its mounting holes and install the new rear engine mount mounting
bolts (A).
manual
Tuesday, February 16, 2016 2:13:50 PM Page 51 2005 Mitchell Repair Information Company, LLC.
51
2012 Acura TL
2012 ENGINE Engine Assembly - TL
Fig. 88: Identifying Rear Engine Mounting Bolts (M/T Model) With Torque Specifications
Courtesy of AMERICAN HONDA MOTOR CO., INC.
3. Install the rear engine mount bracket (A) from the top by sliding it into place from the driver's side.
4. Loosely install the new two rear engine mount bracket mounting bolts (A) and the new rear engine mount
mounting bolt (B).
manual
Tuesday, February 16, 2016 2:13:50 PM Page 52 2005 Mitchell Repair Information Company, LLC.
52
2012 Acura TL
2012 ENGINE Engine Assembly - TL
Fig. 90: Identifying Harness Bracket And Mounting Bolts (M/T Model) With Torque Specifications
Courtesy of AMERICAN HONDA MOTOR CO., INC.
Fig. 91: Identifying Rear Engine Mount Bracket Mounting Bolts (M/T Model) With Torque
Specifications
Courtesy of AMERICAN HONDA MOTOR CO., INC.
manual
Tuesday, February 16, 2016 2:13:50 PM Page 53 2005 Mitchell Repair Information Company, LLC.
53
2012 Acura TL
2012 ENGINE Engine Assembly - TL
Fig. 92: Identifying Rear Engine Mount Bracket Mounting Bolts And Mount Mounting Bolt (M/T
Model) With Torque Specifications
Courtesy of AMERICAN HONDA MOTOR CO., INC.
13. Install the under-hood fuse/relay box with the mounting bracket, and tighten the two mounting nuts (A)
and the mounting bolt (B).
manual
Tuesday, February 16, 2016 2:13:50 PM Page 54 2005 Mitchell Repair Information Company, LLC.
54
2012 Acura TL
2012 ENGINE Engine Assembly - TL
Fig. 93: Identifying Mounting Nuts And Mounting Bolt Of Mounting Bracket (M/T Model) With
Torque Specifications
Courtesy of AMERICAN HONDA MOTOR CO., INC.
14. Install the two harness clamps (A) and the brake booster vacuum hose clamp (B) to the under-hood
fuse/relay box mounting bracket (C).
Fig. 94: Identifying Harness Clamps, Hose Clamp And Mounting Bracket (M/T Model)
Courtesy of AMERICAN HONDA MOTOR CO., INC.
15. Connect the harness connectors (A), then install the harness clamp (B) on the left strut tower.
manual
Tuesday, February 16, 2016 2:13:50 PM Page 55 2005 Mitchell Repair Information Company, LLC.
55
2012 Acura TL
2012 ENGINE Engine Assembly - TL
Fig. 95: Identifying Harness Connectors And Harness Clamps On Left Strut Tower (M/T Model)
Courtesy of AMERICAN HONDA MOTOR CO., INC.
REMOVAL-A/T MODEL
manual
Tuesday, February 16, 2016 2:13:50 PM Page 56 2005 Mitchell Repair Information Company, LLC.
56
2012 Acura TL
2012 ENGINE Engine Assembly - TL
Fig. 96: Identifying Harness Connectors And Harness Clamps On Left Strut Tower (A/T Model)
Courtesy of AMERICAN HONDA MOTOR CO., INC.
7. Remove the two harness clamps (A) and the brake booster vacuum hose clamp (B) from the under-hood
fuse/relay box mounting bracket (C).
Fig. 97: Identifying Mounting Bracket, Harness Clamps And Hose Clamp (A/T Model)
Courtesy of AMERICAN HONDA MOTOR CO., INC.
8. Remove the mounting bolt (A) and the two mounting nuts (B) from the under-hood fuse/relay box
mounting bracket, then tilt the under-hood fuse/relay box forward.
manual
Tuesday, February 16, 2016 2:13:50 PM Page 57 2005 Mitchell Repair Information Company, LLC.
57
2012 Acura TL
2012 ENGINE Engine Assembly - TL
9. Remove the vacuum hose (A) from the clamp (B) and disconnect the vacuum hose from the three way
valve (C).
10. Remove the rear engine mount stop (A), then remove the rear engine mount bolt (B).
manual
Tuesday, February 16, 2016 2:13:50 PM Page 58 2005 Mitchell Repair Information Company, LLC.
58
2012 Acura TL
2012 ENGINE Engine Assembly - TL
Fig. 100: Identifying Rear Engine Mount Stop And Mount Bolt (A/T Model)
Courtesy of AMERICAN HONDA MOTOR CO., INC.
Fig. 101: Identifying Rear Engine Mount Mounting Bolts (A/T Model)
Courtesy of AMERICAN HONDA MOTOR CO., INC.
12. Lift and support the engine with a jack and a wood block under the engine/transmission.
13. Remove the rear engine mount (A) from the top by sliding it out, and lifting it out from the driver's side.
manual
Tuesday, February 16, 2016 2:13:50 PM Page 59 2005 Mitchell Repair Information Company, LLC.
59
2012 Acura TL
2012 ENGINE Engine Assembly - TL
INSTALLATION-A/T MODEL
1. Install the rear engine mount (A) from the top by sliding it into place from the driver's side and route the
vacuum hose (B) through the hole in the mount base bracket (C).
Fig. 103: Identifying Rear Engine Mount, Vacuum Hose And Base Bracket (A/T Model)
Courtesy of AMERICAN HONDA MOTOR CO., INC.
manual
Tuesday, February 16, 2016 2:13:50 PM Page 60 2005 Mitchell Repair Information Company, LLC.
60
2012 Acura TL
2012 ENGINE Engine Assembly - TL
2. Align the rear engine mount with its mounting holes and install the new rear engine mount mounting
bolts (A).
Fig. 104: Identifying Rear Engine Mount Mounting Bolts (A/T Model) With Torque Specifications
Courtesy of AMERICAN HONDA MOTOR CO., INC.
manual
Tuesday, February 16, 2016 2:13:50 PM Page 61 2005 Mitchell Repair Information Company, LLC.
61
2012 Acura TL
2012 ENGINE Engine Assembly - TL
Fig. 105: Identifying Rear Engine Mount Bolt And Mount Stop (A/T Model) With Torque
Specifications
Courtesy of AMERICAN HONDA MOTOR CO., INC.
5. Connect the vacuum hose (A) to the three way valve (B) and install the vacuum hose on its clamp (C) at
the mark (D).
Fig. 106: Identifying Vacuum Hose, Three Way Valve, Clamp And Mark On Vacuum Hose (A/T
Model)
Courtesy of AMERICAN HONDA MOTOR CO., INC.
6. Install the under-hood fuse/relay box with the mounting bracket, and tighten the two mounting nuts (A)
and the mounting bolt (B).
manual
Tuesday, February 16, 2016 2:13:50 PM Page 62 2005 Mitchell Repair Information Company, LLC.
62
2012 Acura TL
2012 ENGINE Engine Assembly - TL
Fig. 107: Identifying Mounting Nuts And Mounting Bolt (A/T Model) With Torque Specifications
Courtesy of AMERICAN HONDA MOTOR CO., INC.
7. Install the two harness clamps (A) and the brake booster vacuum hose clamp (B) to the under-hood
fuse/relay box mounting bracket (C).
Fig. 108: Identifying Harness Clamps, Hose Clamp And Mounting Bracket (A/T Model)
Courtesy of AMERICAN HONDA MOTOR CO., INC.
8. Connect the harness connectors (A), then install the harness clamp (B) on the left strut tower.
manual
Tuesday, February 16, 2016 2:13:50 PM Page 63 2005 Mitchell Repair Information Company, LLC.
63
2012 Acura TL
2012 ENGINE Engine Assembly - TL
Fig. 109: Identifying Harness Connectors And Harness Clamp On Left Strut Tower (A/T Model)
Courtesy of AMERICAN HONDA MOTOR CO., INC.
1. Remove the front splash shield (see FRONT SPLASH SHIELD REPLACEMENT ).
2. Remove the engine compartment covers (see ENGINE COMPARTMENT COVER
REPLACEMENT ).
3. Remove the air cleaner (see THROTTLE BODY CLEANING ).
4. Lift and support the engine with a jack and a wood block under the transmission.
5. Remove the upper transmission mount bracket mounting bolts.
NOTE: Do not remove the bolt (A) from the upper transmission mount. If the bolt
is removed, the upper transmission mount must be replaced as an
assembly.
manual
Tuesday, February 16, 2016 2:13:50 PM Page 64 2005 Mitchell Repair Information Company, LLC.
64
2012 Acura TL
2012 ENGINE Engine Assembly - TL
INSTALLATION-M/T MODEL
manual
Tuesday, February 16, 2016 2:13:50 PM Page 65 2005 Mitchell Repair Information Company, LLC.
65
2012 Acura TL
2012 ENGINE Engine Assembly - TL
Fig. 112: Identifying Upper Transmission Mount (M/T Model) With Torque Specifications
Courtesy of AMERICAN HONDA MOTOR CO., INC.
2. Loosely install the new upper transmission mount bracket mounting bolts.
Fig. 113: Identifying Upper Transmission Mount Bracket Mounting Bolts With Torque
Specifications
Courtesy of AMERICAN HONDA MOTOR CO., INC.
REMOVAL-A/T MODEL
1. Remove the front splash shield (see FRONT SPLASH SHIELD REPLACEMENT ).
2. Remove the engine compartment covers (see ENGINE COMPARTMENT COVER
REPLACEMENT ).
3. Remove the air cleaner (see THROTTLE BODY CLEANING ).
4. Lift and support the engine with a jack and a wood block under the transmission.
5. Disconnect the transmission fluid pressure switch E (6th clutch) connector (A). Remove the harness
bracket (B), then remove the upper transmission mount bracket mounting bolts.
NOTE: Do not remove the bolt (C) from the upper transmission mount. If the bolt
is removed, the upper transmission mount must be replaced as an
assembly.
Fig. 114: Identifying Connector, Harness Bracket And Bolts (A/T Model)
Courtesy of AMERICAN HONDA MOTOR CO., INC.
manual
Tuesday, February 16, 2016 2:13:50 PM Page 67 2005 Mitchell Repair Information Company, LLC.
67
2012 Acura TL
2012 ENGINE Engine Assembly - TL
Fig. 115: Identifying Upper Transmission Mount With Mounting Bolts (A/T Model)
Courtesy of AMERICAN HONDA MOTOR CO., INC.
INSTALLATION-A/T MODEL
Fig. 116: Identifying Upper Transmission Mount With Mounting Bolts (A/T Model) With Torque
Specifications
Courtesy of AMERICAN HONDA MOTOR CO., INC.
2. Loosely install the new upper transmission mount bracket mounting bolts, then install the harness bracket
(A). Connect the transmission fluid pressure switch E (6th clutch) connector (B).
manual
Tuesday, February 16, 2016 2:13:50 PM Page 68 2005 Mitchell Repair Information Company, LLC.
68
2012 Acura TL
2012 ENGINE Engine Assembly - TL
Fig. 117: Identifying Harness Bracket And Connector With Torque Specification Of Bolts (A/T
Model) With Torque Specifications
Courtesy of AMERICAN HONDA MOTOR CO., INC.
1. Remove the front splash shield (see FRONT SPLASH SHIELD REPLACEMENT ).
2. Support the engine/transmission with a transmission jack.
3. Remove the lower transmission mount bracket (A), then remove the lower transmission mount (B).
manual
Tuesday, February 16, 2016 2:13:50 PM Page 69 2005 Mitchell Repair Information Company, LLC.
69
2012 Acura TL
2012 ENGINE Engine Assembly - TL
Fig. 118: Identifying Lower Transmission Mount Bracket And Transmission Mount (M/T Model)
Courtesy of AMERICAN HONDA MOTOR CO., INC.
INSTALLATION-M/T MODEL
Fig. 119: Identifying Lower Transmission Mount Bracket And Transmission Mount (M/T Model)
With Torque Specifications
Courtesy of AMERICAN HONDA MOTOR CO., INC.
2. Loosely install the lower transmission mount bracket (B) using new bolts.
3. Remove the transmission jack.
manual
Tuesday, February 16, 2016 2:13:50 PM Page 70 2005 Mitchell Repair Information Company, LLC.
70
2012 Acura TL
2012 ENGINE Engine Assembly - TL
4. Tighten the lower transmission mount bracket mounting bolts and the lower transmission mount
mounting nuts.
5. Install the front splash shield (see FRONT SPLASH SHIELD REPLACEMENT ).
REMOVAL-A/T MODEL
1. Remove the front splash shield (see FRONT SPLASH SHIELD REPLACEMENT ).
2. Lift and support the engine with a transmission jack and a wood block under the transmission.
3. Remove the lower transmission mount bracket (A), then remove the lower transmission mount (B).
Fig. 120: Identifying Lower Transmission Mount Bracket And Transmission Mount (A/T Model)
Courtesy of AMERICAN HONDA MOTOR CO., INC.
INSTALLATION-A/T MODEL
manual
Tuesday, February 16, 2016 2:13:50 PM Page 71 2005 Mitchell Repair Information Company, LLC.
71
2012 Acura TL
2012 ENGINE Engine Assembly - TL
Fig. 121: Identifying Lower Transmission Mount Bracket And Transmission Mount (A/T Model)
With Torque Specifications
Courtesy of AMERICAN HONDA MOTOR CO., INC.
2. Loosely install the lower transmission mount bracket (B) using new bolts (C).
3. Remove the transmission jack and the wood block.
4. Tighten the lower transmission mount bracket mounting bolts and the lower transmission mount
mounting nuts.
5. Install the front splash shield (see FRONT SPLASH SHIELD REPLACEMENT ).
manual
Tuesday, February 16, 2016 2:13:50 PM Page 72 2005 Mitchell Repair Information Company, LLC.
72