Documente Academic
Documente Profesional
Documente Cultură
SECTION
LIGHTING SYSTEM
LT B
E
CONTENTS
SERVICE INFORMATION ............................ 3 Component Parts and Harness Connector Loca- F
tion ...........................................................................20
PRECAUTIONS ................................................... 3 System Description ..................................................20
Precaution for Supplemental Restraint System Wiring Diagram - TURN - ........................................22 G
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN- Front Turn Signal Lamp Does Not Operate .............23
SIONER" ................................................................... 3 Side Turn Signal Lamp Does Not Operate ..............24
Rear Turn Signal Lamp Does Not Operate .............25
HEADLAMP ......................................................... 4 H
Electrical Component Inspection .............................26
Component Parts and Harness Connector Loca-
tion ............................................................................ 4 COMBINATION SWITCH .................................. 27
System Description ................................................... 4 Replacement ...........................................................27 I
Wiring Diagram - H/LAMP - ....................................... 5
Headlamp High Beam Does Not Illuminate (Both SIDE TURN SIGNAL LAMP .............................. 28
Sides) ........................................................................ 6 Bulb Replacement ...................................................28
Removal and Installation .........................................28 J
Headlamp High Beam Does Not Illuminate (One
Side) .......................................................................... 7
Headlamp Low Beam Does Not Illuminate (Both
STOP LAMP ...................................................... 29
Wiring Diagram - STOP/L - ......................................29 LT
Sides) ........................................................................ 8
Headlamp Low Beam Does Not Illuminate (One BACK-UP LAMP ............................................... 30
Side) ........................................................................ 10 Wiring Diagram - BACK/L - ......................................30
Bulb Replacement ................................................... 11 L
Removal and Installation ......................................... 12 PARKING, LICENSE AND TAIL LAMPS ......... 31
Aiming Adjustment .................................................. 12 Component Parts and Harness Connector Loca-
tion ...........................................................................31 M
HEADLAMP AIMING CONTROL .......................14 System Description ..................................................31
Component Parts Location ...................................... 14 Wiring Diagram - TAIL/L - ........................................32
System Description ................................................. 14 Parking, License Plate and Tail Lamps Do Not Il-
Wiring Diagram - H/AIM - ........................................ 15 luminate ...................................................................33 N
The Supplemental Restraint System such as AIR BAG and SEAT BELT PRE-TENSIONER, used along C
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the SRS and SB section of
this Service Manual.
WARNING: D
To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer. E
Improper maintenance, including incorrect removal and installation of the SRS can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SRS section.
F
Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
G
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni- H
tion ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the I
battery, and wait at least 3 minutes before performing any service.
LT
ALLIA0868ZZ
1. Combination switch (lighting switch) M29, M30 2. Combination meter M206 (with tachometer),
M207
LT
AALWA0012GB
P
AALWA0013GB
(+) E
() Voltage
Headlamp connector Terminal
RH E1
1 Ground Battery voltage F
LH E7 AWLIA1569ZZ
OK or NG
OK >> GO TO 4. G
NG >> GO TO 5.
4.CHECK HEADLAMP GROUND CIRCUIT
H
Check continuity between headlamp harness connector and ground.
(+)
() Voltage
Headlamp connector Terminal
RH E1
1 Ground Battery voltage
LH E7
OK or NG
OK >> GO TO 4. AWLIA1569ZZ
NG >> GO TO 5.
4.CHECK HEADLAMP GROUND CIRCUIT
Check continuity between headlamp harness connector and ground.
A B
Circuit Continuity
Connector Terminal Connector Terminal
RH 6 E1
M30 1 Yes
LH 9 E7
OK or NG
OK >> Replace combination switch. Refer to LT-27, "Replace- AWLIA1568ZZ
ment" .
NG >> Repair harness or connector.
Headlamp Low Beam Does Not Illuminate (Both Sides) INFOID:0000000005473378
(+)
() Voltage
Headlamp connector Terminal F
RH E1
3 Ground Battery voltage
LH E7 AWLIA1572ZZ
G
OK or NG
OK >> GO TO 4.
NG >> GO TO 5.
H
4.CHECK HEADLAMP GROUND CIRCUIT
Check continuity between headlamp harness connector and ground.
I
Headlamp connector Terminal Continuity
RH E1 Ground
2 Yes J
LH E7
OK or NG
OK >> Check headlamp connector for damage or poor connec- LT
tion. Repair as necessary.
NG >> Repair harness.
AWLIA1567ZZ
L
5.CHECK HEADLAMP CIRCUIT
1. Disconnect combination switch connector.
M
A B
Circuit Continuity
Connector Terminal Connector Terminal
RH M30 7 E1
3 Yes
LH M29 10 E7
OK or NG
OK >> Replace combination switch. Refer to LT-27, "Replace-
ment" .
NG >> Repair harness or connector.
AWLIA1571ZZ
(+)
() Voltage
Headlamp connector Terminal
RH E1
3 Ground Battery voltage
LH E7
OK or NG
OK >> GO TO 4. AWLIA1572ZZ
NG >> GO TO 5.
4.CHECK HEADLAMP GROUND CIRCUIT
A B
Circuit Continuity F
Connector Terminal Connector Terminal
RH M30 7 E1
3 Yes
LH M29 10 E7 G
OK or NG
OK >> Replace combination switch. Refer to LT-27, "Replace-
ment" . H
NG >> Repair harness or connector.
LT
AWLIA1571ZZ
REMOVAL
NOTE:
M
The headlamp is a semi-sealed beam type which uses a replaceable halogen bulb. The bulb can be replaced
from the engine compartment side without removing the headlamp body.
1. Disconnect the battery cable.
N
2. Disconnect the harness connector from the back side of the bulb.
LEL376A
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
Do not leave headlamp reflector without bulb for a long period of time. Dust, moisture, smoke, etc.
entering headlamp body may affect the performance of the headlamp. Remove headlamp bulb from
the headlamp reflector just before a replacement bulb is installed.
Removal and Installation INFOID:0000000005473381
REMOVAL
1. Remove the radiator grille. Refer to EI-15, "Removal and Installation".
2. Disconnect the harness connectors from the back side of the headlamp assembly.
3. Remove the bolts and the headlamp assembly.
INSTALLATION
Installation is in the reverse order of removal.
Aiming Adjustment INFOID:0000000005473382
LEL378A
LT
WEL536A
If the vehicle front body has been repaired and/or the headlamp assembly has been replaced, check aiming.
Use the aiming chart shown in the figure. L
Basic illuminating area (shaded) for adjustment should be within the range shown on the aiming
chart. Adjust headlamps accordingly.
M
ALLIA0869ZZ
LT
AALWA0014GB
P
ALLIA0871ZZ
1. Combination switch (lighting switch) M29, front fog lamp switch M67
LT
AALWA0184GB
P
LEL384A
1. Set the distance between the screen and the center of the front
fog lamp lens as shown.
2. Turn front fog lamps ON.
MEL327G
3. Adjust front fog lamps so that the top edge of the high intensity
zone is 100 mm (4 in) below the height of the fog lamp centers
as shown.
When performing adjustment, if necessary, cover the head-
lamps and opposite fog lamp.
WKIA0205E
B
1. Remove front fog lamp.
2. Remove bulb cover.
3. Release the spring retainer. C
4. Disconnect fog lamp bulb connector.
5. Remove fog lamp bulb.
D
6. Install in reverse order of removal. Ensure top of lens faces up.
DO NOT TOUCH BULB.
E
LEL380A
I
LT
ALLIA0870ZZ
1. Combination switch (lighting switch) 2. Combination meter M206, M207 3. Combination flasher unit M21
M30
4. Hazard switch M59
AALWA0191GB
LT
AALWA0185GB
1.CHECK BULB
Verify the bulb standard of each turn signal lamp is correct. Refer to LT-42, "Bulb Specification" .
OK or NG
OK >> GO TO 2.
NG >> Replace turn signal lamp bulb. Refer to LT-28, "Bulb Replacement" .
1.CHECK BULB
Verify the bulb standard of each turn signal lamp is correct. Refer to LT-42, "Bulb Specification" .
OK or NG
OK >> GO TO 2.
NG >> Replace turn signal lamp bulb.
2.CHECK SIDE TURN SIGNAL LAMP CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect combination switch connector and side turn signal
lamp LH or RH connector.
3. Check continuity between combination switch harness connec-
tor M30 (A) terminal 3 and side turn signal lamp LH harness
connector E71 (B) terminal 1.
1.CHECK BULB F
Verify the bulb standard of each turn signal lamp is correct. Refer to LT-42, "Bulb Specification".
OK or NG
G
OK >> GO TO 2.
NG >> Replace turn signal lamp bulb. Refer to LT-37, "Bulb Replacement".
2.CHECK REAR TURN SIGNAL LAMP CIRCUIT H
1. Turn ignition switch OFF.
2. Disconnect combination switch connector and rear combination
lamp LH or RH connector. I
3. Check continuity between combination switch harness connec-
tor M30 (A) terminal 3 and rear combination lamp LH harness
connector T1 (B) terminal 2 (with 8-way combination lamp con-
nector) or connector T1 (C) terminal 2 (with 6-way combination J
lamp connector).
A: M30 3 Yes L
C: T1 (with 6-way combination lamp
2
connector)
4. Check continuity between combination switch harness connector M30 (A) terminal 2 and rear combination
lamp RH harness connector T7 (B) terminal 2 (with 8-way combination lamp connector) or connector T7 M
(C) terminal 2 (with 6-way combination lamp connector).
AWLIA1579ZZ
SEL865L E
MEL205B
I
Before installing the steering wheel, align the turn signal cancel tab
with the notch of the combination switch. Refer to SRS-23.
J
LT
ARS152
P
REMOVAL
1. Remove the side turn signal lamp.
2. Remove the bulb and socket.
INSTALLATION
Installation is in the reverse order of removal.
Removal and Installation INFOID:0000000005473395
REMOVAL
1. Slide the lamp towards the rear of the vehicle and remove the assembly from the front fender, front edge
first.
2. Disconnect the harness connector.
INSTALLATION
Installation is in the reverse order of removal.
LT
P
AALWA0183GB
AALWA0186GB
ALLIA0871ZZ
E
1. Combination switch (lighting switch) M29
The control of the parking, license plate and tail lamp operation is dependent upon the position of combination
switch (lighting switch). When the combination switch is placed in the 1st or 2nd position power is directed to
G
parking, license plate and tail lamps, which then illuminate.
Power is supplied at all times
through 10A fuse (No. 4, located in the fuse block)
to combination switch terminal 11. H
OPERATION BY LIGHTING SWITCH
With the lighting switch in the 1ST or 2ND position power is directed
through combination switch terminal 12 I
to front combination lamp LH and RH terminal 3
to rear combination lamp LH and RH terminal 1 and
to license plate lamp LH and RH terminal 2. J
Ground is supplied
to front combination lamp LH and RH terminal 1
through grounds E15 and E24,
to rear combination lamp LH and RH terminal 3 LT
to license plate lamp LH and RH terminal 1
through grounds M57 and M61.
With power and ground supplied, parking, license plate and tail lamps illuminate. L
AALWA0192GB
LT
AALWA0187GB
(+)
() Voltage
Front combination lamp connector Terminal
A: E19 (with headlamp aiming control)
RH
B: E19 (without headlamp aiming control) Battery
3 Ground
A: E13 (with headlamp aiming control) voltage
LH
B: E13 (without headlamp aiming control)
AWLIA1580ZZ
(+)
() Voltage
License plate lamp connector Terminal
RH A: T5
A: T4 (without step bumper) 2 Ground Battery voltage
LH
B: T4 (with step bumper)
AWLIA1581ZZ
(+)
() Voltage
Rear combination lamp connector Terminal
A: T7 (with 8-way combination lamp con-
nector)
RH
B: T7 (with 6-way combination lamp con-
nector) Battery
1 Ground
A: T1 (with 8-way combination lamp con- voltage
nector)
LH
B: T1 (with 6-way combination lamp con-
AWLIA1582ZZ
nector)
OK or NG
OK >> GO TO 4.
NG >> GO TO 3.
3.CHECK PARKING, LICENSE PLATE AND TAIL LAMP CIRCUIT
1. Disconnect combination switch connector.
2. Check continuity between combination switch harness connec-
tor (A) and front combination lamp harness connector (B) or (C).
aiming control)
AWLIA1584ZZ
D
Con- Termi-
Connector Terminal Continuity
nector nal
F
B: T7 (with 8-way combination
lamp connector)
RH
C: T7 (with 6-way combination
lamp connector) G
A: M29 12 1 Yes
B: T1 (with 8-way combination
lamp connector) AWLIA1585ZZ
LH
C: T1 (with 6-way combination H
lamp connector)
OK or NG
OK >> Replace combination switch. Refer to LT-27, "Replacement". I
NG >> Repair harness or connector.
4.CHECK PARKING, LICENSE PLATE AND TAIL LAMPS GROUND CIRCUIT
1. Check continuity between front combination lamp harness con- J
nector and ground.
M
AWLIA1586ZZ
AWLIA1587ZZ
REMOVAL B
1. Remove the rear combination lamp.
2. Turn the bulb socket counterclockwise to remove the bulb and
socket. C
3. bulb straight out, away from the socket to release.
WKIA3780E
I
INSTALLATION
Installation is in the reverse order of removal.
J
Removal and Installation INFOID:0000000005473403
REMOVAL LT
1. Open the tailgate and remove the rear combination lamp bolts.
2. Pull the rear combination lamp rearward.
3. Rotate each bulb socket counterclockwise to unlock it from the L
lamp assembly housing and remove the assembly from the
vehicle.
M
N
WKIA3781E
INSTALLATION
Installation is in the reverse order of removal. O
ALLIA0872ZZ
1. Interior room lamp 2. Interior room lamp 3. Front door switch (driver side) M41
R4 (single cab) R5, R6 (double cab)
When room lamp switch is in DOOR position, room lamp ON/OFF is controlled by front door switch drivers
side.
POWER SUPPLY AND GROUND
Power is supplied at all times
through 10A fuse (No. 3, located in fuse block)
to interior room lamp terminal 1.
When the interior room lamp switch is turned ON, ground is supplied
to interior room lamp terminal 2 (single cab)
through grounds M57 and M61.
to interior room lamp (double cab) via case ground.
When front door drivers side is opened, ground is supplied
to interior room lamp (single cab) terminal 3
to interior room lamp (double cab) terminal 2.
With power and ground supplied, the interior room lamp illuminates.
LT
AALWA0010GB
P
The control of the illumination lamps is dependent upon the position of the lighting switch. When the lighting
switch is placed in the 1ST or 2ND position, power is directed to the illumination lamps.
Power is supplied at all times
through 10A fuse (No. 4, located in the fuse block)
to combination switch terminal 11.
ILLUMINATION OPERATION BY LIGHTING SWITCH
With the lighting switch in the 1ST or 2ND position, power is supplied
to fan switch terminal 1,
to hazard switch terminal 7,
to audio unit terminal 9 (if equipped),
to combination meter terminal 7 and
to headlamp aiming switch terminal 3 (if equipped).
Ground is supplied
to fan switch terminal 2,
to hazard switch terminal 8,
to combination meter terminal 41 (with tachometer) or terminal 26 (without tachometer) and
to headlamp aiming switch terminal 4 (if equipped)
through grounds M57 and M61.
Ground for the audio unit is supplied via case ground.
With power and ground supplied, illumination lamps illuminate.
LT
AALWA0011GB
P
HEADLAMP
Wattage (W)*
High/Low (Semi-sealed beam) 60/55
*: Always check with the Parts Department for the latest parts information.
EXTERIOR LAMP
Wattage (W)*
Turn signal (Except Brazil and Argentina) 27
Front combination lamp Turn signal (Brazil and Argentina) 21
Parking 5
Side marker 5
Turn signal (Except Brazil and Argentina) 27
Turn signal (Brazil and Argentina) 21
Stop/Tail (Except Brazil and Argentina) 27/8
Rear combination lamp (Chassis)
Stop/Tail (Brazil and Argentina) 21/5
Back-up (Except Brazil and Argentina) 27
Back-up (Brazil and Argentina) 21
Turn signal 27
Rear combination lamp (with side lock tail gate) Stop/Tail 21/5
Back-up 21
Turn signal 21
Rear combination lamp (with one touch lock tail
Stop/Tail 21/5
gate)
Back-up 21
with step bumper 10
License plate lamp without step bumper (Stake type) 10
without step bumper (Chassis type) 5
Front fog light (If so equipped) 55
*: Always check with the Parts Department for the latest parts information.
INTERIOR LAMP
Wattage (W)*
Room lamp (Dome lamp) 10
Map lamp 8
*: Always check with the Parts Department for the latest parts information.