Documente Academic
Documente Profesional
Documente Cultură
General Description
The C30 is a range of centrifugal superchargers with a very
versatile application range. Countless number of medium
size applications can be boosted by this very efficient and
silent unit which supplies air flow up to 0.39 kg/s.
Applications
The C30 range of superchargers is designed for four stroke gasoline engines.
However two stroke engines or even diesel engines can benefit from these
superchargers with remarkable results. Depending on the application the C30 will support engine outputs up
to 320kW. Where one supercharger is not enough, it is possible to use two units to support large amounts of
power in a twin-charger configuration. The C30 can also supply clean pressurized air for other applications
such as industrial systems, exhaust gas after-treatment systems, agriculture applications, fuel cell power
plants etc.
The groundbreaking compact size enables a very flexible supercharger installation particularly on engine
applications with tight space and where weight and size are essential.
Rotrex uses as standard an 8 ribbed poly V-belt pulley in high strength steel. Pulley diameter ranges from 70
to 110mm in 5mm steps.
The supercharger can be ordered with the compressor housing mounted in one of six different outlet
positions with 60 degree intervals to allow easy adoption to any application. For specific outlet positions
please refer to dimension drawing found in this document.
Oil system
The supercharger features an integrated dual-action oil pump that works as a dry sump scavenging pump in
addition to being the oil supply pump. The self-contained oil system allows flexible positioning of the
supercharger on the vehicle and has the benefit of fitting the supercharger without worrying about tampering
with the oil system of the engine or any other accessory.
The Rotrex C-type supercharger has been developed and extensively tested with the special Rotrex traction
fluid. To maintain the ultimate level of performance and durability it is very important that the unit is
exclusively run with special Rotrex traction fluid. Make sure the inlet oil temperature is within the range
specified in the table on the next page. Any deviation from the standard Rotrex oil circuit requires approval
from Rotrex.
www.rotrex.com
Product: C30 range
Version: 5.0
Technical Data Sheet Page 2 of 7
Characteristics
Power range
1
Prange 120-235kW 135-255kW 140-265kW 145-320kW
(163-320hp) (184-347hp) (190-360hp) (197-435hp)
Max mass flow rate Mflow 0.28 kg/s 0.31 kg/s 0.32 kg/s 0.39 kg/s
1
Power output is dependent on engine type, cooling, cam-timing etc.
Conversion Toolbox
5 9
Temperature conversion C = (F 32) OR F = C + 32
9 5
kg kg CFM
Kg/s to CFM conversion CFM = 1731.8 = @15C and 0.1013MPa
s s 1731.8
kg kg / s
Kg/s to lb/min conversion = 0.0075 lb / min lb / min =
s 0.0075
www.rotrex.com
Product: C30 range
Version: 5.0
Technical Data Sheet Page 3 of 7
2.8
120k
2.6
2.4
68
2.2
70
Pressure Ratio
100k
2.0
1.8
60
80k 72
1.6
65
50
1.4
60k
50
1.2
50 55
40k
40
45
20k 35
1
0 0.05 0.10 0.15 0.20 0.25 0.30
Air Flow [kg/s] RTR 0068
www.rotrex.com
Product: C30 range
Version: 5.0
Technical Data Sheet Page 4 of 7
3.0
2.8
120k
2.6
50
2.4
65
Pressure Ratio
2.2
100k
2.0
1.8
72
80k
1.6
50
70
68
1.4
60
60k 50
1.2
40k 55
50
40
45
20k 35
1
0 0.04 0.08 0.12 0.16 0.20 0.24 0.28 0.32
Air Flow [kg/s] RTR 0069
www.rotrex.com
Product: C30 range
Version: 5.0
Technical Data Sheet Page 5 of 7
2.8
120k
2.6
2.4
65
55
2.2 100k
Pressure Ratio
68
2.0
70
60
1.8
80k 72
1.6
1.4 60k 55
1.2
40k
50
4 45
35 0
20k 35
1
0 0.04 0.08 0.12 0.16 0.20 0.24 0.28 0.32
Air Flow [kg/s] RTR 0070
www.rotrex.com
Product: C30 range
Version: 5.0
Technical Data Sheet Page 6 of 7
2.6
100k
55
2.4
60
90k
2.2
2.0
Pressure Ratio
80k
55
1.8
70k
70
68
1.6
60k
71
1.4
50k
65
60
40k
1.2 50
30k
45 45
20k 40
1
0 0.06 0.12 0.18 0.24 0.30 0.36 0.42
Air Flow [kg/s] RTR 0071
www.rotrex.com
Product: C30 range
Version: 5.0
Technical Data Sheet Page 7 of 7
Dimensions
www.rotrex.com