Documente Academic
Documente Profesional
Documente Cultură
SCX-1000I
SCX-1000SI
SERVICE Manual
1. Precautions
2. Specifications
7. Block Diagrams
8. PCB Diagrams
9. Schematic Diagrams
ELECTRONICS
Follow these safety, ESD, and servicing precautions to prevent personal injury and equipment damage.
1. Be sure that all built-in protective devices are in 7. Product Safety Notice:
place. Restore any missing protective shields. Some electrical and mechanical parts have special
safety-related characteristics which might not be
2. Make sure there are no cabinet openings through obvious from visual inspection. These safety
which people- particularly children- might insert features and the protection they provide could be
fingers or objects and contact dangerous voltages. lost if a replacement component differs from the
original. This holds true, even though the
3. When re-installing chassis and assemblies, be replacement may be rated for higher voltage,
sure to restore all protective devices, including wattage, etc.
control knobs and compartment covers.
Components critical for safety are indicated in
4. Design Alteration Warning: the parts list with symbols . Use only
Never alter or add to the mechanical or electrical replacement components that have the same
design of this equipment, such as auxiliary ratings, especially for flame resistance and
connectors, etc. Such alterations and dielectric specifications. A replacement part that
modifications will void the manufacturers does not have the same safety characteristics as
warranty. the original may create shock, fire, or other safety
hazards.
5. Components, parts, and wiring that appear to
have overheated or are otherwise damaged
should be replaced with parts which meet the
original specifications. Always determine the
cause of damage or overheating, and correct any
potential hazards.
Certain semiconductor devices can be easily 4. Use only an anti-static solder removal device.
damaged by static electricity. Such components are Some solder removal devices not classified as
commonly called Electrostatically Sensitive (ES) anti-static can generate electrical charges
Devices, or ESDs. Examples of typical ESDs are: sufficient to damage ESDs.
integrated circuits, some field effect transistors, and
semiconductor chip components. 5. Do not use Freon-propelled chemicals. When
The techniques outlined below should be followed sprayed, these can generate electrical charges
to help reduce the incidence of component damage sufficient to damage ESDs.
caused by static electricity.
6. Do not remove a replacement ESD from its
CAUTION: Be sure no power is applied to the protective packaging until immediately before
chassis or circuit, and observe all other safety installing it. Most replacement ESDs are
precautions. packaged with all leads shorted together by
conductive foam, aluminum foil, or a comparable
conductive material.
1. Immediately before handling a semiconductor
component or semiconductor-equipped assembly, 7. Immediately before removing the protective
drain off any electrostatic charge on your body shorting material from the leads of a replacement
by touching a known earth ground. Alternatively, ESD, touch the protective material to the chassis
employ a commercially available wrist strap or circuit assembly into which the device will be
device, which should be removed for your personal installed.
safety reasons prior to applying power to the unit
under test. 8. Maintain continuous electrical contact between
the ESD and the assembly into which it will be
2. After removing an electrical assembly equipped installed, until completely plugged or soldered
with ESDs, place the assembly on a conductive into the circuit.
surface, such as aluminum or copper foil, or
conductive foam, to prevent electrostatic charge 9. Minimize bodily motions when handling
buildup in the vicinity of the assembly. unpackaged replacement ESDs. Normal motions,
such as the brushing together of clothing fabric
3. Use only a grounded tip soldering iron to solder and lifting ones foot from a carpeted floor, can
or desolder ESDs. generate static electricity sufficient to damage an
ESD.
2-1 Copier
Maximum Print-edge Margin Top: 3.4mm, Bottom: 19.5mm, Each Side: 6.5mm
Multicopy 99 pages
2-2 Printer
Emulation HBP
Note:
(2) Speed claims based on the test files: spdtst.sam(mono), spdtstc2.sam(color)/Letter size
(3) Non-standard cable can cause misoperations.
2-3 Scanner
Compatibility TWAIN
Scan Width Max.: 8.5 (216 mm), Effective: 8.2 (210 mm)
2-4 Ink-head
DC Channels (4)
+5V +5%, +12V +2%, +30V +5%
2-6 Dimension
2-7 Packaging
USB Cable No
CD-ROM 2EA
Ink Cartridge Mono 1EA, Color 1EA
Manual 2vol.
Note:
(5) Packing Condition
MEMO
1. Remove the guide outer. 2. Remove two screws securing the rear cover.
Separate the rear cover from the main frame.
2. Remove two screws and take out the PCB cover. 4. Unplug the harness and one connector from
the main PBA.
FPC cable
6. Place the scanner support to its original 7. Pull the scanner unit backward and remove the
position. assembly from the main frame.
3-4 Scanner
1. Before you disassemble the scanner, you should
remove: Planten cover
* Scanner unit assembly (See page 3-3)
3. Pull the cover upward and remove it. 5. Remove the glass from the main frame.
1
2
7. Remove C-cap, then push the part marked 9. Remove the cover of the motor bracket.
with A and remove the belt.
3-9 SMPS
1. Before you disassemble the SMPS, you should 3. Remove one connector, then remove the SMPS.
remove:
* Rear cover. (See page 3-1)
1. Before you disassemble the FPC holder assembly 3. Pull the part out to unlatch the FPC holder
you should remove: and pull the sensor actuator out, then slide
* All covers (See page 3-1, 3-9, 3-10) the FPC holder in the direction of .
* Scanner unit (See page 3-2)
* Engine unit. (See page 3-10)
6. Push the holder pulley to the direction of 7. Unlatch the encoder by releasing both ends
arrow and remove it from the main frame. hooked to the main frame using a sharp tool.
Take out the encoder.
4. Push the holder pulley and remove the belt only. 5. Remove two screws securing the carrier motor
and take out the motor from the main frame.
1. Before you disassemble the roller holder you 3. Pull the holder downward and take it out from
should remove: the main frame.
* All covers (See page 3-1, 3-9, 3-10)
* Scanner unit assembly (see page 3-2)
* Engine unit (See page 3-10)
* FPC holder assembly (See page 3-11)
* Cartridge assembly (See page 3-12)
1. Before you disassemble the ASF assembly you 3. Unlatch the inner cover by pushing the parts
should remove: hooked to the ASF frame using a sharp tool,
* All covers (See page 3-1, 3-9, 3-10) then take out inner cover.
* Scanner unit (see page 3-2)
* Engine unit (See page 3-10)
4. Pull the gear out, then remove the drive roller. 5. Remove one screw securing the gear to the
main frame and remove the gear. Then take
out the pick-up roller.
4-1 SCANNER
4-1-1 COPY
Check the CIS problem in Main PBA. If the CIS is defective, replace it.
- CN6-1 is 3.2V when white original copying.
- Cn6-1 is 1.4V when idle.
Check turning the CIS LED on when Check the CIS harness contact.
operating.
Check the CIS problem in Main PBA. If the CIS is defective, replace it.
- CN6-1 is 3.2V when white original copying.
- CN6-1 is 1.4V when idle.
Check the scanner glass and any Check the right position of the scanner glass,
mechanical disturbance. and check the any mechanical disturbance in the
Abnormal noise CIS carriaging part.
Check the motor driver in Driver PBA. If any driver is defective, replace it.
- U9-1, 19 or U10-1, 19 = 0V to 30V swing signal
when operating.
4-1-2 PC-Scan
Check how TWAIN driver is installed. Remove any other scanner driver.
Reboot after reinstallation of the TWAIN driver.
Scanning error Check harness contact. Check CN4 contact in Main PBA, CN1 contact in
Driver PBA whether each connection is tight.
Check the IEEE1284 signal level. If any signal level is defective, replace Driver
PBA.
- U44-43~51 in Main PBA = 0.8V to 2.4V TTL
signal.
Otherwise, replace Main PBA.
Defective image Check the gap between original and The gap above 0.5mm can cause a blurred
quality scanner glass. image.
Check the scanner glass and any Check the right position of the scanner glass,
mechanical disturbance. and check the any mechanical disturbance in the
CIS carriaging part.
Abnormal noise
Check the motor driver in Driver PBA. If any driver is defective, replace it.
- U9-1, 19 or U10-1, 19 = 0V to 30V swing signal
when operating.
4-2 Printer
Cause
If nozzles in print head has a problem, white lines CARTRIDGE MAINT will let you know if nozzles
are marked on the print. have fallen problems.
Solution
1) Run print control panel to clean print nozzles 4) Replace ink cartridge and check whether theres a
and check if nozzles have been blocked. problem with the head.
2) Wipe with soft cloth the contact surfaces of ink 5) Check if head cable is inserted well into the main
cartridge and carriage, and check if nozzles have circuit board and then check if nozzles have
been cleaned properly. problems.
3) Separate ink cartridge from carriage and combine 6) Check if head cable is broken or torn and then
them. Repeat it about 5 to 6 times and check if check if nozzles have problems.
connection is proper. 7) Replace the main circuit board with a new one
and check if nozzles have problems.
ALIGNMENT A
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30
ALIGNMENT B
0 1 2 3 4 5 6 7
8 9 10 11 12 13 14 15
ALIGNMENT C
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30
ALIGNMENT D
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30
ALIGNMENT E
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30
ALIGNMENT F
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30
Check the printer cable installed. Check correct installation, and use standard
IEEE1284 cable.
Cant Print
Check what printer driver is installed. Remove the driver.
Reboot after reinstallation of the print driver.
Check harness contact. Check CN4 contact in Main PBA, CN1 contact in
Driver PBA whether each connection is tight.
Check the USB harness contact. Check CN4 contact in Driver PBA and CN10
contact in Main PBA.
Check the IEEE1284 signal level. If any signal level is defective, replace Driver
PBA.
- U44-47~50 in Main PBA = 0.8V to 2.4V TTL
signal.
Otherwise, replace Main PBA.
Check the USB signal level. If and signal level is detective, replace Main
PBA.
Check if pickup roller rubber of the ASF is Replace pickup roller rubber.
worn out.
Cant feed envelopes Check the location of the envelope guide Open the envelope guide when you feed
of ASF. envelopes.
Tilted printing Check if paper guide of the ASF is Adjust paper guide to the size of paper.
adjusted to the size of paper.
Check the power supply. Check the fuse. If the fuse is defected, replace it
with 250V/3A.
Check the output voltage in power alone.
- CON1-1 = 5V +5%
- CON1-2 = GND 5V
- CON1-3 = 12V +2%
- CON1-4 = GND 12V
Operation panel does
- CON1-5 = GND 30V
not operate.
- CON1-6 = 30V +5%
Check the driver IC defect. The following driver ICs defect can cause power
down. Remove a IC and check the power on.
- U37, U39, U25, and U26 in Main PBA
- U2, U3, U4, U9, and U10 in Driver PBA
Check the download mode. Download the firmware of recent version, and
check the system initial.
Check the harness contact. Check CN10 and CN14 contact in Main PBA
whether each connection is tight.
Check the key contacts. Check the mechanical defect, and replace the
front cover.
Check the harness contact. Check CN5 contact in Main PBA, CN2 contact in
Driver PBA, and CN5, 8 in Driver PBA whether
each connection is tight.
LF motor does not
operate Check the control signals of U44-139-144 If these CMOS signals are defective when the
in Main PBA. other functions normal, replace the Main PBA.
Check the motor signals of U2-1, 19 and If these 30V signals are defective when the other
U3-1, 19 in Driver PBA. functions normal, replace the Driver PBA.
Check the harness contact. Check CN5 contact in Main PBA, CN2 contact in
Driver PBA, and CN5, 7 in Driver PBA whether
each connection in tight.
SCAN motor does not
operate Check the control signals of U12-112-119 If these CMOS signals are defective when the
in Main PBA. other functions normal, replace the Main PBA.
Check the motor signals of U9-1, 19 and If these 30V signals are defective when the other
U10-1, 19 in Driver PBA. functions normal, replace the Driver PBA.
Check the motor signals of U4-1, 19 in If these 30V signals are defective when the other
Driver PBA. functions normal, replace the Driver PBA.
Check the paper jamming. Check the real jammming in paper path, and
remove it.
Check the ASF. Check the ASF according the Paper Feed.
Check paper
Check the sensor output in Main PBA. Check 5V of U12-64 when the sensor lever is
interrupted, and 0V of U12-64 when the sensor
lever is lifted. If the sensor is defected, replace it.
Check the sensor output in Main PBA. Check 5V of U12-63 when the sensor lever is
freely lifted, and 0V of U12-63 when the sensor
lever is pressed. If the sensor is defected,
Cover open replace it.
In service (tech) mode, the technician can check the 1. Press the MENU button until CIS TEST is
machine and perform various tests to isolate the displayed in LCD.
cause of a malfunction. 2. Press the START button when the CIS Test
operation menu CIS TEST displayed.
To enter the service mode, press Enter , Stop , Left , 3. After scanner calibrating, wave form will be
Right , Setup in sequence, and the LCD displays automatically printed out.
TECH, the machine has entered service (Tech)
mode.
WARNNING!
- Shading profile must be made after Downloading a new
Firmware. If not, system will not work properly.
- When you test CIS, make sure that the cover is closed.
1. In the service mode, press the Setup button until 1. In the service mode, press the Setup button until
CARTRIDGE is displayed. DOWNLOAD is displayed.
2. Press the Start button when the CHANGE CRT 2. Press the Start button, and the printer goes into
operation menu is displayed. the downloading mode.
3. To download the ROM file from the PC
connected to the printer using the parallel cable
4-4-3-1 Change Cartridge (IEEE 1284), type in the DOS prompt: COPY /b
SCX1000S LPT1 (where SCX1000S is the ROM
Allows you to change the cartridge. For information file.)
on replacing the cartridge, refer to the Users Guide. 4. When downloading is successfully completed,
the printer returns to the idle mode.
Notes:
You must install the color cartridge into the left Notes:
holder, the black (or photo) cartridge into the right After Download, you must clear the memory.
holder. To enter the Memory clear,power off and on
When you inset a new cartridge, push the and then press the Stop button untill memory
cartridge until it snaps in place. clearing is displayed in LCD.
After replacing the cartridge, you must align the
cartridge.
Note: After downloading, you must perform the memory clearing process. Turn the printer off, and then
turn it on with the Stop button pressed and held down until the printer displays memory clearing on
the LCD.
SA
1 MS
UN
G
2
16
s1
3 4
5
15
14
7
13
12
10
11
0 SCX-1000 * 1 X
0 SCX-1000S * 1 X
1 ELA UNIT- SCANNER JB96-01143A 1 O
2 PMO-COVER PBA * 1 X
3 PMO-COVER SIDE LEFT * 1 X
4 PBA MAIN-BOARD JB92-01136A 1 O 1000
4 PBA-SUB-MAIN JB92-01107A 1 O 1000S
5 MEC-COVER MIDDLE * 1 X
6 ELA UNIT-PANEL OPE refer to information 1 O 1000
6 ELA UNIT-PANEL OPE refer to information 1 O 1000S
7 PBA-SUB-SMIB JB92-01094A 1 O ONLY 1000S
8 PRINT HEAD MONO BIRCH * 1 X
8 PRINT HEAD COLOR BIRCH * 1 X
9 ELA UNIT-ENGINE * 1 X
10 ELA UNIT-FRAME ASF * 1 X
11 PMO-SUPPORTER SMPS * 1 X
12 SMPS-FV JB44-00008A 1 O
13 ELA UNIT DRIVER JB96-01147A 1 O
14 PMO-COVER SIDE RIGHT * 1 X
15 PMO-COVER REAR * 1 X
16 PMO-COVER HARNESS * 1 X
S1 SCREW-TAPPING 6002-000175 18 O
O: Service available X: Service not available
*Buyer Information
BUYER ELA UNIT-PANEL OPE
SCX-1000I/XXAA JB96-01159B
SCX-1000SI/XAA JB96-01144B
SCX-1000SI/XAC JB96-01144B
SCX-1000SI/XEN JB96-01144B
SCX-1000I/XEU JB96-01159B
SCX-1000SI/XEU JB96-01144B
SCX-1000SI/XEG JB96-01144C
SCX-1000I/XIL JB96-01159D
SCX-1000SI/XIL JB96-01144D
SCX-1000SI/XET JB96-01144E
0
SA
MS SA
UN
G 2 MS
UN
G
1-1
1-2
1-3
4-1
4
4-2
6
5
5-1
5-2 18 16
5-3 5-4
17
7 5-5
15-1
15-7 15-5
8 10-5 s1
9 15-4
13 s2
10-1
15-6
10-2 15-3
10-4
10-3
15-2
15
11 12
10
12 14
2
3
6
5
4
7
S1
8
S1
4 PMO-KEY FUNCTION * 1 X
5 PMO-KEY BLACK * 1 X
6 PMO-CAP COLOR * 1 X
S1 SCREW-TAPPING 6002-000175 9 O
O: Service available X: Service not available
*Buyer Information
BUYER ELA UNIT-PANEL OPE
SCX-1000I/XXAA JB96-01159B
SCX-1000SI/XAA JB96-01144B
SCX-1000SI/XAC JB96-01144B
SCX-1000SI/XEN JB96-01144B
SCX-1000I/XEU JB96-01159B
SCX-1000SI/XEU JB96-01144B
SCX-1000SI/XEG JB96-01144C
SCX-1000I/XIL JB96-01159D
SCX-1000SI/XIL JB96-01144D
SCX-1000SI/XET JB96-01144E
3
2
2 MEC-SUPPORT SCANNER * 1 X
1-11
4-1 12-1
12-2
4-2
1-3 3
1-2 1-12 4-6
Exploded Views and Parts Lists
1-4 4-9
4-8
0
S2
1-7 4-10
3-2 12-3
4-7
1-9 3-4 2 4-5 4-6 4-4 12-4-1
1-10
4-3 12-4
5-5 Engine Exploded View
15-4
1
15 11
9
15-3
15-1
15-2 10
5
15-5
14-1
15-6 14-5 14-2
15-8 14-3
14-6 14-4
15-7
14-7 14
16 16-1 14-8
16-2
16-4
16-3
Samsung Electronics
Exploded Views and Parts Lists
Samsung Electronics
20 9
S1 27
26
14 11
21-3
10 21-1 21-4 13
21 21-2
0
5 20
18 16
25
5-6 Frame ASF Exploded View
15
7 17 3
4
23
24
6
8-5
8 8-2 8-7
2
8-1
8-6 1
8-4
8-3
Exploded Views and Parts Lists
5-13
Exploded Views and Parts Lists
1 FOOT * 2 X
2 PMO-FRAME ASF * 1 X
5 PMO-RX-STACKER MAIN * 1 X
6 PMO-STACKER (L) * 1 X
7 PMO-STACKER S JB72-41398C 1 O
8 MEC-CASSETTE ASF * 1 X
11 PMO-GUIDE INNER * 1 X
12 E-RING * 2 X
15 PMO-LEVER CASSETTE * 1 X
16 SPRING-LEVER LOCKING * 1 X
17 GEAR-IDLE 32 * 1 X
18 GEAR-IDLER ASF * 1 X
19 GEAR-DOUBLE 25/28(0.8) * 1 X
20 GEAR-DOUBLE 20/14 * 1 X
21 MEC-ARM(SWING 1X12) * 1 X
22 MEC-GUIDE OUTER * 1 X
23 PMO-BUCKLER FRICTION * 1 X
24 PMO-HOUSING-BUCKLER * 1 X
25 PMO-GUIDE-PAPER * 3 X
S1 SCREW-TAPPING * 1 X
S2 SCREW-TAPPING * 1 X
O: Service available X: Service not available
MEMO
Main PBA(SCX-1000I)
SEC CODE LOCATION NO. Qty DESCRIPTION
2007-000297 R122 1 R-CHIP 10KOHM,1%,1/10W,DA,TP,2012
2007-000297 R96,R134,R136,R137 4 R-CHIP 10KOHM,1%,1/10W,DA,TP,2012
2007-000300 R12,R13,R83,R127 4 R-CHIP 10KOHM,5%,1/10W,DA,TP,2012
2007-000300 R150,R151,R159,R160 4 R-CHIP 10KOHM,5%,1/10W,DA,TP,2012
2007-000300 R165,R167 2 R-CHIP 10KOHM,5%,1/10W,DA,TP,2012
2007-000300 R204,R205 2 R-CHIP 10KOHM,5%,1/10W,DA,TP,2012
2007-000300 R4,R6,R9,R10 4 R-CHIP 10KOHM,5%,1/10W,DA,TP,2012
2007-000300 R81 1 R-CHIP 10KOHM,5%,1/10W,DA,TP,2012
2007-000303 R116 1 R-CHIP 10KOHM,5%,1/8W,DA,TP,3216
2007-000308 R200 1 R-CHIP 10OHM,5%,1/10W,DA,TP,2012
2007-000392 R125,R130 2 R-CHIP 150KOHM,1%,1/10W,DA,TP,2012
2007-000401 R148 1 R-CHIP 150OHM,5%,1/10W,DA,TP,2012
2007-000465 R71,R73,R74,R82 4 R-CHIP 1KOHM,1%,1/10W,DA,TP,2012
2007-000465 R98 1 R-CHIP 1KOHM,1%,1/10W,DA,TP,2012
2007-000468 R101,R158 2 R-CHIP 1KOHM,5%,1/10W,DA,TP,2012
2007-000468 R22,R25,R26,R28,R29 5 R-CHIP 1KOHM,5%,1/10W,DA,TP,2012
2007-000468 R30,R36,R42,R43,R49 5 R-CHIP 1KOHM,5%,1/10W,DA,TP,2012
2007-000468 R46,R77 2 R-CHIP 1KOHM,5%,1/10W,DA,TP,2012
2007-000468 R51,R52,R57,R58,R78 5 R-CHIP 1KOHM,5%,1/10W,DA,TP,2012
2007-000468 R63,R75 2 R-CHIP 1KOHM,5%,1/10W,DA,TP,2012
2007-000474 R85,R103,R132 3 R-CHIP 1MOHM,1%,1/10W,DA,TP,2012
2007-000542 R145 1 R-CHIP 200OHM,5%,1/8W,DA,TP,3216
2007-000686 R201 1 R-CHIP 3.3KOHM,5%,1/10W,DA,TP,2012
2007-000705 R123 1 R-CHIP 3.6KOHM,5%,1/8W,DA,TP,3216
2007-000766 R109,R110 2 R-CHIP 330OHM,5%,1/10W,DA,TP,2012
2007-000781 R152,R153 2 R-CHIP 33OHM,5%,1/10W,DA,TP,2012
2007-000814 R131 1 R-CHIP 39.2KOHM,1%,1/8W,DA,TP,3216
2007-000841 R32,R35 2 R-CHIP 3KOHM,1%,1/10W,DA,TP,2012
2007-000844 R119,R156 2 R-CHIP 3KOHM,5%,1/10W,DA,TP,2012
2007-000844 R146,R147 2 R-CHIP 3KOHM,5%,1/10W,DA,TP,2012
2007-000872 R17,R21,R40,R90,R129 5 R-CHIP 4.7KOHM,5%,1/10W,DA,TP,2012
2007-000941 R104 1 R-CHIP 47KOHM,5%,1/10W,DA,TP,2012
2007-000964 R120,R121 2 R-CHIP 5.1KOHM,5%,1/10W,DA,TP,2012
2007-000964 R33,R34,R38,R61,R68 5 R-CHIP 5.1KOHM,5%,1/10W,DA,TP,2012
2007-000964 R45,R54,R55,R60,R107 5 R-CHIP 5.1KOHM,5%,1/10W,DA,TP,2012
2007-000964 R69,R80,R86,R114,R115 5 R-CHIP 5.1KOHM,5%,1/10W,DA,TP,2012
2007-001001 R91 1 R-CHIP 510OHM,5%,1/10W,DA,TP,2012
2007-001041 R112 1 R-CHIP 56KOHM,5%,1/8W,DA,TP,3216
2007-001041 R118 1 R-CHIP 56KOHM,5%,1/8W,DA,TP,3216
2007-001055 R99 1 R-CHIP 6.2KOHM,5%,1/10W,DA,TP,2012
2007-001152 R16 1 R-CHIP 750OHM,1%,1/10W,DA,TP,2012
2007-001243 R124 1 R-CHIP 91KOHM,5%,1/10W,DA,TP,2012
2007-001273 R141,R142 2 R-CHIP 5.23KOHM,1%,1/10W,DA,TP,2012
2007-007029 R128 1 R-CHIP 1.33KOHM,1%,1/10W,DA,TP,2012
2007-007427 R89,R95 2 R-CHIP 294OHM,1%,1/10W,DA,TP,2012
2011-001093 RA1,RA2,RA3,RA4,RA5 5 R-NETWORK 100ohm,5%,1/16W,L,CHIP,8P,TP
2011-001093 RA6,RA7,RA8,RA9 4 R-NETWORK 100ohm,5%,1/16W,L,CHIP,8P,TP
2011-001094 RA10,RA11,RA12 3 R-NETWORK 39ohm,5%,63mW,L,CHIP,8P,TP
2203-000192 C104~C108 5 C-CERAMIC,CHIP 100nF,+80-20%,50V,Y5V,TP,2012,
2203-000192 C109,C110,C111,C113,C119 5 C-CERAMIC,CHIP 100nF,+80-20%,50V,Y5V,TP,2012,
2203-000192 C120,C121,C122 3 C-CERAMIC,CHIP 100nF,+80-20%,50V,Y5V,TP,2012,
2203-000192 C14,C15,C17,C18 4 C-CERAMIC,CHIP 100nF,+80-20%,50V,Y5V,TP,2012,
2203-000192 C22,C26 2 C-CERAMIC,CHIP 100nF,+80-20%,50V,Y5V,TP,2012,
2203-000192 C29,C33,C34 3 C-CERAMIC,CHIP 100nF,+80-20%,50V,Y5V,TP,2012,
2203-000192 C3,C4,C5,C6,C7,C143 6 C-CERAMIC,CHIP 100nF,+80-20%,50V,Y5V,TP,2012,
2203-000192 C36,C37,C38 3 C-CERAMIC,CHIP 100nF,+80-20%,50V,Y5V,TP,2012,
2203-000192 C41,C42,C46,C47,C48 5 C-CERAMIC,CHIP 100nF,+80-20%,50V,Y5V,TP,2012,
2203-000192 C49,C50,C57,C58 4 C-CERAMIC,CHIP 100nF,+80-20%,50V,Y5V,TP,2012,
2203-000192 C69,C91 2 C-CERAMIC,CHIP 100nF,+80-20%,50V,Y5V,TP,2012,
Main PBA(SCX-1000I)
SEC CODE LOCATION NO. Qty DESCRIPTION
2203-000192 C71,C72 2 C-CERAMIC,CHIP 100nF,+80-20%,50V,Y5V,TP,2012,
2203-000192 C79,C83,C85 3 C-CERAMIC,CHIP 100nF,+80-20%,50V,Y5V,TP,2012,
2203-000192 C87,C88,C89,C92 4 C-CERAMIC,CHIP 100nF,+80-20%,50V,Y5V,TP,2012,
2203-000192 C9,C10,C11 3 C-CERAMIC,CHIP 100nF,+80-20%,50V,Y5V,TP,2012,
2203-000192 C94,C96,C98,C101,C103 5 C-CERAMIC,CHIP 100nF,+80-20%,50V,Y5V,TP,2012,
2203-000192 CR145,CR146,CR147,CR148 4 C-CERAMIC,CHIP 100nF,+80-20%,50V,Y5V,TP,2012,
2203-000239 C118,C123,C124,C125,C126 5 C-CERAMIC,CHIP 0.1nF,5%,50V,NP0,TP,2012
2203-000239 C127,C130 2 C-CERAMIC,CHIP 0.1nF,5%,50V,NP0,TP,2012
2203-000239 C23,C53,C66,C149 4 C-CERAMIC,CHIP 0.1nF,5%,50V,NP0,TP,2012
2203-000239 C97,C114,C117,C128,C129 5 C-CERAMIC,CHIP 0.1nF,5%,50V,NP0,TP,2012
2203-000260 C68,C80,C82,L1 4 C-CERAMIC,CHIP 10nF,10%,50V,X7R,TP,2012
2203-000274 C176,C177 2 C-CERAMIC,CHIP 0.01nF,0.25pF,50V,NP0,TP,2012
2203-000274 C67 1 C-CERAMIC,CHIP 0.01nF,0.25pF,50V,NP0,TP,2012
2203-000455 C54,C60 2 C-CERAMIC,CHIP 1nF,5%,50V,NP0,TP,2012
2203-000455 C65,C73 4 C-CERAMIC,CHIP 1nF,5%,50V,NP0,TP,2012
2203-000476 C186 1 C-CERAMIC,CHIP 1000nF,+80-20%,16V,Y5V,TP,2012
2203-000495 C16 1 C-CERAMIC,CHIP 2.2nF,10%,50V,X7R,TP,2012
2203-000595 C52,C55 2 C-CERAMIC,CHIP 0.22nF,5%,50V,NP0,TP,2012
2203-000595 C61,C81,C84,C112 4 C-CERAMIC,CHIP 0.22nF,5%,50V,NP0,TP,2012
2203-000634 C187 1 C-CERAMIC,CHIP 0.022nF,5%,50V,NP0,TP,2012
2203-000634 C188 1 C-CERAMIC,CHIP 0.022nF,5%,50V,NP0,TP,2012
2203-000634 C43 1 C-CERAMIC,CHIP 0.022nF,5%,50V,NP0,TP,2012
2203-000634 C51 1 C-CERAMIC,CHIP 0.022nF,5%,50V,NP0,TP,2012
2203-000938 C56 1 C-CERAMIC,CHIP 0.47nF,5%,50V,NP0,TP,2012
2203-001002 C174,C175 2 C-CERAMIC,CHIP 0.047nF,5%,50V,NP0,TP,2012
2203-001077 C86,C100 2 C-CERAMIC,CHIP 0.056nF,5%,50V,NP0,TP,2012
2203-001223 C189 1 C-CERAMIC,CHIP 0.82nF,10%,50V,X7R,TP,2012
2203-001223 C74,C99 2 C-CERAMIC,CHIP 0.82nF,10%,50V,X7R,TP,2012
2401-000172 C93 1 C-AL 1000uF,20%,35V,GP,TP,12.5x20mm
2402-000130 C70 1 C-AL,SMD 2.2uF,20%,50V,GP,TP,4.3x4.3x5.
2402-000139 C134 1 C-AL,SMD 22uF,20%,35V,GP,TP,6.6x6.6x5.4
2402-000168 C95,C116 2 C-AL,SMD 100uF,20%,16V,GP,TP,8.3x8.3x6.3mm
2402-000176 C2,C45,C59,C115 4 C-AL,SMD 10uF,20%,16V,GP,TP,4.3x4.3x5.4
2402-000179 C102 1 C-AL,SMD 47uF,20%,16V,GP,TP,6.6x6.6x5.4
2703-000266 C142 1 INDUCTOR-SMD 220nH,10%,1.25x2x0.85mm
2801-001375 Y3 1 CRYSTAL-UNIT 10MHz,20ppm,28-AAA,16pF,45ohm,BK
2801-003699 Y2 1 CRYSTAL-UNIT 48MHz,50ppm,28-ABM,12pF,80ohm,
3301-000317 R162,R163,R164,R8 4 CORE-FERRITE BEADAB,2x1.25x0.9mm,-,-
3301-000325 B1,B5,B10 3 CORE-FERRITE BEADAB,3.2x2.5x1.3mm,-,-
3301-000325 B2,B7,B8 3 CORE-FERRITE BEADAB,3.2x2.5x1.3mm,-,-
3708-001058 CN6,CN8,CN11 3 CONNECTOR-FPC/FC/PIC 30P,1.0MM,STRAIGHT,SN
3708-001187 CN3,CN4 2 CONNECTOR-FPC/FC/PIC 23P,1mm,STRAIGHT,SN
3708-001425 CN9 1 CONNECTOR-FPC/FC/PIC 12P,1.25MM,STRAIGHT,SN
3711-000225 CN5 1 CONNECTOR-HEADER 1WALL,4P,1R,2.5mm,STRAIGHT,SN
3711-002806 CN2 1 CONNECTOR-HEADERBOX,5P,1R,2mm,STRAIGHT,SN
3711-002807 CN10 1 CONNECTOR-HEADERBOX,6P,1R,2mm,STRAIGHT,SN
3711-003409 CN7 1 CONNECTOR-HEADERBOX,3P,1R,2mm,STRAIGHT,SN
4701-001037 U27 1 FREQ-ATTENUATOR 6to82MHz,8dB,-,0.12W
JB13-00001A U6 1 IC-ASIC-IMAGE PROCESSORSCX-1010,DUOIP,QFP,160,28X28MM
JB13-00002A U21 1 IC ASIC-UNICON MJC-1300G,UNICON,QFP,44P,-
JB13-10508A U7 1 IC ASIC-CPU SF-4700,KS32C6400,SMD,160P,-
JB41-00051A PCB 1 PCB-MAIN SCX-1000S,FR-4,4 LAYER,-,1.6 T,168*110,-,2,-,-
Main PBA(SCX-1000SI)
SEC CODE LOCATION NO. Qty DESCRIPTION
2007-000297 R96,R134,R136,R137 4 R-CHIP 10KOHM,1%,1/10W,DA,TP,2012
2007-000300 R13,R83,R127,R150 4 R-CHIP 10KOHM,5%,1/10W,DA,TP,2012
2007-000300 R151,R159,R160 3 R-CHIP 10KOHM,5%,1/10W,DA,TP,2012
2007-000300 R4,R6,R9,R10,R11,R12 5 R-CHIP 10KOHM,5%,1/10W,DA,TP,2012
2007-000300 R81,R165 2 R-CHIP 10KOHM,5%,1/10W,DA,TP,2012
2007-000303 R116 1 R-CHIP 10KOHM,5%,1/8W,DA,TP,3216
2007-000392 R125,R130 2 R-CHIP 150KOHM,1%,1/10W,DA,TP,2012
2007-000401 R148 1 R-CHIP 150OHM,5%,1/10W,DA,TP,2012
2007-000465 R71,R73,R74,R82 4 R-CHIP 1KOHM,1%,1/10W,DA,TP,2012
2007-000465 R98 1 R-CHIP 1KOHM,1%,1/10W,DA,TP,2012
2007-000468 R101,R158 2 R-CHIP 1KOHM,5%,1/10W,DA,TP,2012
2007-000468 R22,R25,R26,R28,R29 5 R-CHIP 1KOHM,5%,1/10W,DA,TP,2012
2007-000468 R30,R36,R42,R43,R46 5 R-CHIP 1KOHM,5%,1/10W,DA,TP,2012
2007-000468 R49,R51,R52,R57,R58 5 R-CHIP 1KOHM,5%,1/10W,DA,TP,2012
2007-000468 R77,R78 2 R-CHIP 1KOHM,5%,1/10W,DA,TP,2012
2007-000474 R85,R103,R132 3 R-CHIP 1MOHM,1%,1/10W,DA,TP,2012
2007-000542 R145 1 R-CHIP 200OHM,5%,1/8W,DA,TP,3216
2007-000703 R63,R75 2 R-CHIP 3.6KOHM,5%,1/10W,DA,TP,2012
2007-000705 R123 1 R-CHIP 3.6KOHM,5%,1/8W,DA,TP,3216
2007-000766 R15,R109,R110 3 R-CHIP 330OHM,5%,1/10W,DA,TP,2012
2007-000781 R152,R153 2 R-CHIP 33OHM,5%,1/10W,DA,TP,2012
2007-000814 R131 1 R-CHIP 39.2KOHM,1%,1/8W,DA,TP,3216
2007-000841 R32,R35 2 R-CHIP 3KOHM,1%,1/10W,DA,TP,2012
2007-000844 R119,R156 2 R-CHIP 3KOHM,5%,1/10W,DA,TP,2012
2007-000844 R146,R147 2 R-CHIP 3KOHM,5%,1/10W,DA,TP,2012
2007-000872 R17,21,40,90,129 5 R-CHIP 4.7KOHM,5%,1/10W,DA,TP,2012
2007-000941 R104 1 R-CHIP 47KOHM,5%,1/10W,DA,TP,2012
2007-000964 R120,R121 2 R-CHIP 5.1KOHM,5%,1/10W,DA,TP,2012
2007-000964 R33,R34,R38,R61,R68 5 R-CHIP 5.1KOHM,5%,1/10W,DA,TP,2012
2007-000964 R45,R54,R55,R60,R107 5 R-CHIP 5.1KOHM,5%,1/10W,DA,TP,2012
2007-000964 R69,R80,R86,R114,R115 5 R-CHIP 5.1KOHM,5%,1/10W,DA,TP,2012
2007-001001 R91 1 R-CHIP 510OHM,5%,1/10W,DA,TP,2012
2007-001041 R112 1 R-CHIP 56KOHM,5%,1/8W,DA,TP,3216
2007-001041 R118 1 R-CHIP 56KOHM,5%,1/8W,DA,TP,3216
2007-001055 R99 1 R-CHIP 6.2KOHM,5%,1/10W,DA,TP,2012
2007-001152 R16 1 R-CHIP 750OHM,1%,1/10W,DA,TP,2012
2007-001243 R124 1 R-CHIP 91KOHM,5%,1/10W,DA,TP,2012
2007-001273 R141,R142 2 R-CHIP 5.23KOHM,1%,1/10W,DA,TP,2012
2007-007029 R128 1 R-CHIP 1.33KOHM,1%,1/10W,DA,TP,2012
2007-007427 R89,R95 2 R-CHIP 294OHM,1%,1/10W,DA,TP,2012
2011-001093 RA1,RA2,RA3,RA4,RA5 5 R-NETWORK 100ohm,5%,1/16W,L,CHIP,8P,TP
2011-001093 RA6,RA7,RA8,RA9 4 R-NETWORK 100ohm,5%,1/16W,L,CHIP,8P,TP
2011-001094 RA10,RA11,RA12 3 R-NETWORK 39ohm,5%,63mW,L,CHIP,8P,TP
2203-000192 C106,C107,C108,C109,C110 5 C-CERAMIC,CHIP 100nF,+80-20%,50V,Y5V,TP,2012,
2203-000192 C111,C113,C119,C120,C121 5 C-CERAMIC,CHIP 100nF,+80-20%,50V,Y5V,TP,2012,
2203-000192 C122 1 C-CERAMIC,CHIP 100nF,+80-20%,50V,Y5V,TP,2012,
2203-000192 C14,C15,C17,C18,C19 5 C-CERAMIC,CHIP 100nF,+80-20%,50V,Y5V,TP,2012,
2203-000192 C20,C22,C25,C26,C28 5 C-CERAMIC,CHIP 100nF,+80-20%,50V,Y5V,TP,2012,
2203-000192 C29,C32,C33,C34,C35 5 C-CERAMIC,CHIP 100nF,+80-20%,50V,Y5V,TP,2012,
2203-000192 C3,C4,C5,C6,C7 5 C-CERAMIC,CHIP 100nF,+80-20%,50V,Y5V,TP,2012,
2203-000192 C36,C37,C38,C39,C40 5 C-CERAMIC,CHIP 100nF,+80-20%,50V,Y5V,TP,2012,
2203-000192 C41,C42,C46,C47,C48 5 C-CERAMIC,CHIP 100nF,+80-20%,50V,Y5V,TP,2012,
2203-000192 C49,C50,C57,C58,C62 5 C-CERAMIC,CHIP 100nF,+80-20%,50V,Y5V,TP,2012,
2203-000192 C71,C75,C76 3 C-CERAMIC,CHIP 100nF,+80-20%,50V,Y5V,TP,2012,
Main PBA(SCX-1000SI)
SEC CODE LOCATION NO. Qty DESCRIPTION
2203-000192 C72,C83,C88 3 C-CERAMIC,CHIP 100nF,+80-20%,50V,Y5V,TP,2012,
2203-000192 C77,C78,C79,C85,C87,C143 6 C-CERAMIC,CHIP 100nF,+80-20%,50V,Y5V,TP,2012,
2203-000192 C89,C92,C94,C96 4 C-CERAMIC,CHIP 100nF,+80-20%,50V,Y5V,TP,2012,
2203-000192 C9,C10,C11 3 C-CERAMIC,CHIP 100nF,+80-20%,50V,Y5V,TP,2012,
2203-000192 C98,C101,C103,C104,C105 5 C-CERAMIC,CHIP 100nF,+80-20%,50V,Y5V,TP,2012,
2203-000239 C118,C123,C124,C125,C126 5 C-CERAMIC,CHIP 0.1nF,5%,50V,NP0,TP,2012
2203-000239 C127,C130 2 C-CERAMIC,CHIP 0.1nF,5%,50V,NP0,TP,2012
2203-000239 C129,C149 2 C-CERAMIC,CHIP 0.1nF,5%,50V,NP0,TP,2012
2203-000239 C159,C160,C161,C162,C163 5 C-CERAMIC,CHIP 0.1nF,5%,50V,NP0,TP,2012
2203-000239 C164,C165,C166,C167,C168 5 C-CERAMIC,CHIP 0.1nF,5%,50V,NP0,TP,2012
2203-000239 C169,C170,C171,C172,C173 5 C-CERAMIC,CHIP 0.1nF,5%,50V,NP0,TP,2012
2203-000239 C23,C24 2 C-CERAMIC,CHIP 0.1nF,5%,50V,NP0,TP,2012
2203-000239 C66,C97,C114,C117,C128 5 C-CERAMIC,CHIP 0.1nF,5%,50V,NP0,TP,2012
2203-000260 C68,C80,C82 3 C-CERAMIC,CHIP 10nF,10%,50V,X7R,TP,2012
2203-000260 L1 1 C-CERAMIC,CHIP 10nF,10%,50V,X7R,TP,2012
2203-000274 C67,C176,C177 3 C-CERAMIC,CHIP 0.01nF,0.25pF,50V,NP0,TP,2012
2203-000455 C54,C60 2 C-CERAMIC,CHIP 1nF,5%,50V,NP0,TP,2012
2203-000455 C65,C73 2 C-CERAMIC,CHIP 1nF,5%,50V,NP0,TP,2012
2203-000495 C16 1 C-CERAMIC,CHIP 2.2nF,10%,50V,X7R,TP,2012
2203-000595 C52,C55,C81,C84 4 C-CERAMIC,CHIP 0.22nF,5%,50V,NP0,TP,2012
2203-000595 C61,C112,R167 3 C-CERAMIC,CHIP 0.22nF,5%,50V,NP0,TP,2012
2203-000634 C43 1 C-CERAMIC,CHIP 0.022nF,5%,50V,NP0,TP,2012
2203-000634 C51 1 C-CERAMIC,CHIP 0.022nF,5%,50V,NP0,TP,2012
2203-000938 C56 1 C-CERAMIC,CHIP 0.47nF,5%,50V,NP0,TP,2012
2203-001002 C174,C175 2 C-CERAMIC,CHIP 0.047nF,5%,50V,NP0,TP,2012
2203-001077 C86,C100 2 C-CERAMIC,CHIP 0.056nF,5%,50V,NP0,TP,2012
2203-001223 C74,C99 2 C-CERAMIC,CHIP 0.82nF,10%,50V,X7R,TP,2012
2401-000172 C93 1 C-AL 1000uF,20%,35V,GP,TP,12.5x20mm
2402-000130 C70 1 C-AL,SMD 2.2uF,20%,50V,GP,TP,4.3x4.3x5.
2402-000139 C134 1 C-AL,SMD 22uF,20%,35V,GP,TP,6.6x6.6x5.4
2402-000168 C95,C116 2 C-AL,SMD 100uF,20%,16V,GP,TP,8.3x8.3x6.3mm
2402-000176 C2,C45,C59,C63,C115 5 C-AL,SMD 10uF,20%,16V,GP,TP,4.3x4.3x5.4
2402-000179 C102 1 C-AL,SMD 47uF,20%,16V,GP,TP,6.6x6.6x5.4
2703-000266 C142 1 INDUCTOR-SMD 220nH,10%,1.25x2x0.85mm
2801-003699 Y2 1 CRYSTAL-UNIT 48MHz,50ppm,28-ABM,12pF,80ohm,
2804-000260 OSC1 1 OSCILLATOR-CLOCK40MHz,100ppm,10 TTL,BK,5V,30mA
3301-000317 R162,R163,R164,R8 4 CORE-FERRITE BEADAB,2x1.25x0.9mm,-,-
3301-000325 B1,B4,B5,B6,B10 5 CORE-FERRITE BEADAB,3.2x2.5x1.3mm,-,-
3301-000325 B2,B7,B8 3 CORE-FERRITE BEADAB,3.2x2.5x1.3mm,-,-
3301-001084 R14,L3 2 CORE-FERRITE BEADAB,2.0x1.25x0.9mm,-,-
3708-001058 CN1,CN6,CN8,CN11 4 CONNECTOR-FPC/FC/PIC30P,1.0MM,STRAIGHT,SN
3708-001187 CN3,CN4 2 CONNECTOR-FPC/FC/PIC23P,1mm,STRAIGHT,SN
3708-001425 CN9 1 CONNECTOR-FPC/FC/PIC12P,1.25MM,STRAIGHT,SN
3711-000225 CN5 1 CONNECTOR-HEADER1WALL,4P,1R,2.5mm,STRAIGHT,SN
3711-002806 CN2 1 CONNECTOR-HEADERBOX,5P,1R,2mm,STRAIGHT,SN
3711-002807 CN10 1 CONNECTOR-HEADERBOX,6P,1R,2mm,STRAIGHT,SN
3711-003409 CN7 1 CONNECTOR-HEADERBOX,3P,1R,2mm,STRAIGHT,SN
JB13-00001A U6 1 IC-ASIC-IMAGE PROCESSORSCX-1010,DUOIP,QFP,160,28X28MM
JB13-00002A U21 1 IC ASIC-UNICON MJC-1300G,UNICON,QFP,44P,-
JB13-10506A U9 1 IC ASIC-CDIP DUO-JET,CDIP,QFP,100P,-
JB13-10508A U7 1 IC ASIC-CPU SF-4700,KS32C6400,SMD,160P,-
JB41-00038A 1 PCB- MAIN SCX-1000,FR-4,4 LAYER,1.6 T,168*110
7. Block Diagrams
40MHz
D( 0: 15) MEMORY
/ I P_XDREQ / I P_XDACK ( U3)
A( 0: 17)
/ I P_CS
/ RD, / WR
DUO_I P / CAS
D( 0: 15)
( U6) / RAS0, 1
A( 0: 5)
/ WR DRAM
CI S_SI G D( 0: 15) ( U17, 10)
CI S_CLK C A( 0: 9)
CI S_SH I
S
LED_ON( R, G, B) / USB_RST
LFPHA MFP CONTROLLER / USB_CS
T
o LFPHB KS32C6400 / RD, /WR
D LFI A0 ( U7) D( 0: 7)
TX_PHA UNI CON
r
TX_PHB i LFI A1 A( 0: 5)
( U21)
TX_I A0 v LFI B0
e / USB_I RQ
TX_I A1
r LFI B1 / USB_XDACK
TX_I B0
TX_I B1 P DI R / USB_XDREQ
B PWM
A
48MHz
PD( 0: 7)
CHX
/ ERROR_OUT
CHY T
PE_OUT o
/RST_OUT
BUSY_OUT D
/ ACK_OUT r
/ HEAD_EN i
SLCT_OUT v
PRI NT HEAD HEAD_DATA
/ I NI T_I N e
/ HGA( 1: 13) r
DRI VER
HOE( 1: 16) / SLCTI N_I N
& PRI NT P
OK2PRI NT / AUTOFD_I N B
CONTROL
/ FAULT_TEST A
CIRCUIT / STB_I N
BI ASOFF
245DI R
+22V
POWER
/FA U LT_TE ST CONTROL
/H G A (1:13)
R ow B A(1:13)
D river
(U 24,25) C A (1:13)
H O E(1:16)
KS32C6400
(U 7) C olum n B P (1:16 )
M AIN D river
C P (1:16)
CO NTRO LLER (U 22,23)
Ink
Cartridge
B IAS O FF
C S(1)
H ead
B S(1)
D etection
/C _H E AD _EN HSC
H ead
/M _H EA D _EN H SM
Selector
C PR ES
M P RE S
Fault /F AU LT
O K 2PR IN T
Test
C _H E AD D A TA
M _H EA D D ATA C H (1)
DUO_IP PR EH E AT_C S ubstrate
B H (1)
(U6) P RE H EA T_M H eat
IM AG E
A M B _TEM P
PRO C ESSO R Temperature
Control
R_LED ,
G _LED,
AIN PI_TG B_LED
AD C_REFT PI1
ADC _REFB PI_RS
Shading
Acquisition
Sensor M odule
10-bit SRAM
Control
A/D converter 2560x 10
M odule Shading
C orrection
M odule
Enlargem ent G am m a
SRAM SRAM
/Reduction C orrection
2560X 8 1024x 8
M odule M odule
SR A M _A[15:0]
SR A M _D [7:0]
SR A M _nRD
Color Im age SR A M _nW R
SRAM
C orrection Processing
512X 32 SRAM
M odule M odule
256x 8
CRA, /CRA
PWM SCAN A, / SCANA
CR SCAN AI0 ,1 SC AN LF
DIR LF A, / LFA
Driver:U4 SCAN PH A Driver:U9 Drive r:U2
LF AI0, 1 , L FP HA
(TEA3718S) (TEA3718S) (TEA3718S)
CO NT ROL VBU S,
SIGNAL S, U SBDM,
D0 :D7 USBDP
SC AN SCAN B, /S CA NB LF
SCAN BI0 , 1 , LF B, /L FB
SCAN PH B Drive r:U10 LF BI0 , 1 , L FPH B Driver:U3
RC RC
(TEA3718S) (TEA3718S)
Filte r Filte r
74LVX4245
CONOTRL SI GNAL
S M
M A
I
N
74LVX4245
C
O B
D[ 0: 7]
N '
N D
E
C
T
ECC- GEN
O
R
KSC1623- Y
8-1
JB41-0038A
M30 MAIN REV 1. 1
U10
U3
U5
C136
UR2 BAR CODE U4
C149
U17
TP2TP1TP5TP4TP3
C59
C45
KM416C4104BS-5
AM29F400B-70EC B4
KM68257CJ-15
KM416C1204CJ-L5T
120 OCS1
30
RA8 R31
UR1 40MHZ
C2 120
RA7 110
AM29F400B-70EC
PBA
RA6
CR147 110
C63
KS32C6400
B6
100
B1
RA5
DUO_IP
R87
R92
30 20 10 1
R76 100
SMD
R172 30
CN2
100 R7
R65 30
U12
R77
CD74HC244M
40 C96
CDIP1
2
R107
60 70
C130
R163
50 60 70
KA358D-T/F
C127 U11
C140 22
8-1 Main PCB Diagram(Top)
60 80 C70 CN4
70
RA1
C51
Q11 CN7 R112 R106TP
U9 R41
SN74LS245DW
R198
R111
LED1
R127
C143
U14 KM68257CJ-15 C55 R56 R55 C56
R199
R72
C52 R47 R46 22 Q3
C169
C173
C171
C168
C166
R64
C160
CN5
D5 Q1 C67
U25 U24 RA2
R50
Y2 U16
48MHZ CN3
40
U21
1 R122 Q6
C124
C123
C126
C125
U8 P1
U16 Q2 P2
CD1602
R144
CD1602
8.PCB Diagrams
1
Q10 Q10
YR1 RA4 29
C161
C159
C170
C172
R147
R97
UNICON
30 CN6 2 R104 C102
RA12
R126 Q13
2
10
30 R98 R81 U20
R146
R143
Samsung Electronics
R105
RA11
CN8 C116
CN10 29
CN9
1
RA10
RA3
C115
LR2
1
29
Q12
C134
B10 C93
U23 U22 30 CN11 2 U26 C116
200.02.21
8-2
R22 C23 B2 C9
R23 C68 D1
R158 C48 C75 R175
C150 C13 R90
R12
C58
PCB Diagrams
R29
C3 R4 C158
R25 R101
C4 C5 R193
R17 R3 R5
R43 R2 R26 R28 R178
C10 R182
C16
CR156 R42 CR155 R169 C181
C11 R58 C14 C18 C133 R161
C49 C76
R52 R53 CR148
CR1 C8 R174
R54
R51 R44 R192
C178 C180
C57 R191
R49 R190 R189
CR157 R165 R131 C175
C174 C179
R180
C37 C43 R117 R171
C47 C54 C34 R179 R40 C35
R148 R60 C38
R149 R45
CR145 R181
C44 C28 C164
CR146
R59 C65 R38 C40
C79
C41 R37 R11
8-2 Main PCB Diagram(Bottom)
R123 C85
C19
R33 R67 R68 R116 C25
R32
C129 C167
LM393D
R34 C128 R162 LR1
C112 C62
U19
R35 C60 B7 C163
R36 R16
Q9
R109 R78 C165 R157
R75 D3 C83 C139
R71 D4
R164 C141 C87 C142
R145 C137
C109
R115
C71 R82 R80 C111
C72 C103 L1
C80 C69 C74
R83 C82 C97 C89 C86
R110 C84 R113 C81 R108
R129 C88
R132
R134
C98
R114 R85 R89 R99 C121 C122 C153
R138
Q4
R196
R106 C114 C120 R140 R152
Q14 C176
R156
R100 R154
C117 C119
C113 C104
Samsung Electronics
PCB Diagrams
8-3
BAR CODE
3
CN6
U10 R71
C66 R75
U4 U1
TEA3718S TEA3718S
CN5 C1 U3 TEA3718S
R80
1 2 22
CN2
M30 DRIVER REV 1 . 0 CN8
U9 C64
20000119_BBK
JB41- 00040A
R79
TEA3718S 1 23
2 22
CN1
R58
R57
R56
R55
R54
R53
R52
R52
CN7 R74
U2 TEA3718S
8-3 Driver PCB Diagram(Top)
R19
R18
R17
R20
R16
R15
R14
R13
R100
R99
1 23
CN3
CN4
2 1 CN9
3 4
B2
B1
MADE IN KOREA
Samsung Electronics
PCB Diagrams
8-4 Driver PCB Diagram(Bottom)
C46
C44
R60 R48
6
L1 C12 C13
C39 L2 C33
C51 C45
R67 R64
R77
1 C43
C38 R24 R69 R23
R22
Q3 R42
Q1
R43
DA2
Q2 R25
R21 ZD1
R41
1
4
R44
R40
R45 R46
2
3
R30
C42
R31
R68
C63 C52
R47
R26
2
2
1
R27
1
C2
R28
Q4
C40
R29
19
C25 C41 C9
C26
C27 C18
C28 L8
C29
C30
C31
C32
R78
C56
R81
C58
R85 R84
C55 C60
C57
C62 L4 C54
C53
L5
36
18
LR3
C5
R98
3
1
1
2
1
4
U1
U3 U4
TC74LVX4245MTCX
TC74LVX4245MTCX
C2
C1
C17 C6
R8
C18
C7 C9 C10 C16 U5 D1 R5 C5
C11 C8 C12 Q1
TC7S32FU CN1
R7
C15
R12
1
22 Q3
R11
3
20
R13
5 C14
18 R6
7 Q2
16
R10
9
14 R14
C13
11
12 R9
D2
JB41-00039A
CN2 M30 SMIB REV 1 . O
8-5
Samsung Electronics
8-6
PCB Diagrams
U1
C5
C2
C7
C3
C6
C4
R8
R6
8-6 OPE PCB Diagram
HT48R50
R9
C8
OSC1
SW1 SW2 7.37MHz
R11
D1
J3
R12
R10
SW4
R13
D2
Menu
J1
SW3 SW5 SW13
R3 Resolution Contrast J2 Setup R17 R14
C12 R19
R4 R15
SW8 R18 R21
R16 C13
R20
Stop M30 OPE SM Scan
C14
REV 1 . 1
SW6 SW7 D3 SW9 SW14
Special Copy C9 JB41- 00041A
Zoom Copy Page 2000 . 02 . 17
5 CN2 1
C10
L1
C11 SM Print
Enter
SW15
Blakc Color
Samsung Electronics