Documente Academic
Documente Profesional
Documente Cultură
Input parameters
Fr 25 kN
Radial load
Fa 25 kN
Axial load
ni 1750 r/min
Rotational speed of the inner
ring
Viscosity at 40 C 96 mm2/s
Result
aSKF 0.31
SKF life modification factor aSKF
0.76
Viscosity ratio
P 117 kN
Equivalent dynamic bearing load
c 0.15
Factor for contamination level
1 7.19 mm2/s
Required kinematic viscosity for =1
L10h 1890 hour
Basic rating life
C/P 4.9
Load ratio
Input parameters
ni 1750 r/min
Rotational speed of the inner ring
Lubrication Grease
Result
Pm 6.4 kN
Equivalent minimum load
Input parameters
Fr 25 kN
Radial load
Fa 25 kN
Axial load
ni 1750 r/min
Rotational speed of the inner ring
Viscosity at 40 C 96 mm2/s
Lubrication Grease
Result
Mrr 2726.1 Nmm
Rolling frictional moment
Mseal 0 Nmm
Frictional moment of the seals
Mdrag 0 Nmm
Frictional moment of drag losses
M 8113.2 Nmm
Total frictional moment
Nr 1490 W
Power loss
5.45 mm2/s
Lubricant viscosity at operating temperature
Krs 6.0E-8
Replenishment/starvation constant
Input parameters
ni 1750 r/min
Rotational speed of the inner ring
ne 1750 r/min
Rotational speed of the outer ring (only used to calculate the bearing
frequencies)
Result
fi 29.2 Hz
Rotational frequency of the inner ring
fe 29.2 Hz
Rotational frequency of the outer ring
fc 29.2 Hz
Rotational frequency of the rolling element and cage assembly
fr 0 Hz
Rotational frequency of a rolling element about its own axis
fip 0 Hz
Over-rolling frequency of one point on the inner ring
fep 0 Hz
Over-rolling frequency of one point on the outer ring
frp 0 Hz
Over-rolling frequency of one point on a rolling element
Input parameters
Fr 25 kN
Radial load
Fa 25 kN
Axial load
Viscosity at 40 C 96 mm2/s
Lubrication Grease
Result
fp 0.44
Adjustment factor for bearing load P
fv 1.03
Adjustment factor for grease base oil viscosity
ftot 0.45
fp fv with grease lubrication
Input parameters
Fr 25 kN
Radial load
Fa 25 kN
Axial load
ni 1750 r/min
Rotational speed of the inner ring
Warning
Operating rotational speed is above the maximum recommended speed of 223 r/min (based on SKF Rolling bearings
catalogue).
Result
tf 0 hour
Relubrication interval
0g
Gp
Grease quantity to be added when replenishing
Viscosity : 22222 EK
Input parameters
ni 1750 r/min
Rotational speed of the inner ring
Viscosity at 40 C 96 mm2/s
Result
5.45 mm2/s
Lubricant viscosity at operating temperature
1 7.19 mm2/s
Required viscosity at operating temperature for =1
0.76
Viscosity ratio
Input parameters
Fr 25 kN
Radial load
Fa 25 kN
Axial load
Result
P 117 kN
Equivalent dynamic bearing load
Unit system
Select unit system
SI Imperial
Selected calculations
Bearing life, Minimum load, Frictional moment - power loss, Bearing frequencies, Influence of load
and lubricant viscosity on adjusted reference speed, Relubrication intervals, Viscosity, Equivalent
dynamic bearing load
Bearing data
Designation 22222 EK *
d 110 mm
D 200 mm
B 53 mm
C 572 kN
C0 640 kN
Note: The drawing displayed is only for general representation and may not be identical to the selected bearing variant.
COPYRIGHT
TERMS & CONDITIONS
PRIVACY POLICY
SITE OWNERSHIP
COOKIES
WWW.SKF.COM