Documente Academic
Documente Profesional
Documente Cultură
Features
Elegant Scale Illumination
DC to 30MHz Bandwidth Z Modulation
1mV/div Sensitivity on Both Channels 8 x 10 cm Display Internal Graticule
CH1 & CH2 Independent Channels Auto Focus
CH1 Signal Output TV Triggering Frame (V) & Line (H)
Algebraic Addition and Subtraction Line Trigger
X-Y Operation ALT Triggering
20ns/div to 0.2s/div Time Base C.T. Facility
ALT MAG. Trace - Max. 4 Traces Continuity Tester with Beeper
Specifications
VERTICAL DEFLECTION (Y) Rise Time : 11.6ns or less.
Deflection : 1mV/div to 10V/div. 5mV/div Display Modes : CH1, CH2, DUAL (CH1, CH2
Coefficient to 10V/div in 11 calibrated ALT/CHOP), Algebraic ADD
(CH1 & CH2) steps in 1-2-5 sequence. and SUBTRACT, CH2 INVT &
x5 Magnification increases the X-Y (CH1 as X, CH2 as Y).
sensitivity to 1mV/div to 2V/div. Input Impedance : 1M ohms // 25pF approx.
Accuracy : x1 : ±3%, x5 : ±5%. Maximum Input : 400 Volts (dc + peak ac).
Variable : 1 / 2.5 times uncalibrated Voltage
continuously variable control Internal Trigger : CH1, CH2 or Alternate.
extends the Deflection Coeffi- Signal
cient to more than 25V/div.
Bandwidth : x1 : DC to 30MHz (-3dB), dc CH1 SIG OUT
coupled. Output Voltage : Minimum 20mV for 1 div of
: 10Hz to 30MHz (-3dB), CH1 input signal.
ac coupled.
x5 : DC to 7MHz (dc coupled) Output Impedance : 50 ohms (approx.).
10Hz to 7MHz (ac Bandwidth : 50Hz to 5MHz.
coupled).
TIME BASE HORIZONTAL DEFLECTION
Sweep Speed : 20 Calibrated steps. 0.1μs/div Deflection : Same as CH1.
to 0.2s/div in 1, 2 & 5 Coefficient
sequence. Bandwidth : DC - 3MHz (-3dB).
Sweep Magnifier : x5 Magnification increases the Input Impedance : 1M ohms // 25pF approx.
fastest sweep upto 20ns/div.
Phase Difference : <3O (DC - 100KHz).
Accuracy : ±3%.
Variable : Uncalibrated continuously COMPONENT TESTER
variable control between steps, Component Tester allows V.I. characteristics of a Device
extends slowest sweep speed Under Test (D.U.T.).
to 0.5s/div (approx.).
Test Voltage : 9V rms (No Load).
ALT MAG Trace : x5 magnified sweep is Test Current : 2mA when shorted.
displayed along with normal
sweep. CONTINUITY TESTER (Rear Panel)
TRIGGER SYSTEM Beeper sounds for continuity for resistance <75 ohms
approx.
Triggering Mode : AUTO, NORM, TV-V, TV-H.
Source : INT (CH1 or CH2) / CH2 / GENERAL INFORMATION
LINE / EXT. Cathode Ray Tube : 140mm Rectangular screen,
Slope : Positive or Negative. Internal Graticule, 8 x 10 cm,
P31 phosphor.
Coupling : AC coupling.
Accelerating potential : 2kV.
Trigger Sensitivity
Z-Modulation : ±5V p-p signal upto 2MHz
Internal : Auto : 0.5 div - 20Hz to modulates at normal intensity.
30MHz.
Normal : 0.5 div - 10Hz to Calibrator : Provides 0.5V ±2%, 1KHz ±2%
30MHz. square-wave output for probe
Lock : 2.0 div - 50Hz to compensation.
20MHz. Power Requirement : 220V AC ±10%, 50Hz ±5%,
Alt : >3div - 50Hz to 35VA (max.).
30MHz. Dimensions : 140 (H) x 335 (W) x 375 (D)
External : Auto : 0.3V p-p - 20Hz to mm approx.
30MHz. Weight : 7.2 Kgs. approx.
Normal : 0.3V p-p - 10Hz to
30MHz. Standard : Instruction Manual, 2 High
Lock : 0.3V - 50Hz to Accessories impedance switch probe with
20MHz. x1 or x10 attenuation, Mains
Cord, CT Leads.
Typical : 40MHz.
Environmental : Operating conditions
Specifications Normal : 10OC to 35OC, RH
45% to 85%.
Operational : 0OC to 40OC,
RH 35% to 90%.
WE PURSUE A POLICY OF CONTINUOUS DEVELOPMENT AND PRODUCT IMPROVEMENT. THUS THE SPECIFICATIONS IN
THIS DOCUMENT AND THE LOCATION OF CONTROLS ON THE FRONT PANEL MAY BE CHANGED WITHOUT NOTICE.