Documente Academic
Documente Profesional
Documente Cultură
1
Disconnect PJ1,
PJ4, PJ10 and the
connector on the
tray 3 home sensor.
1
Locate the tongue
into the frame slot.
Support bracket
2
Install 2
screws.
3. Ensure that the tray slide, at the rear right of the tray 3 transport assembly, straddles the
support bracket when the paper feed assembly is replaced.
4. Push tray 3 in slowly and check that the tray does not foul the paper feed assembly.
5. Connect the four PJs, refer to Figure 1.
6. The remainder of the replacement is the reverse of the removal procedure. Refer to GP 6
before refitting the screws.
7. If a new paper feed assembly has been installed, reset the tray 3 feed roll HFSI count.
Refer to dC135 CRU/HFSI Status.
WARNING
Switch off the electricity to the machine, GP 14. Disconnect the power cord from the
customer supply while performing tasks that do not need electricity. Electricity can
cause death or injury. Moving parts can cause injury.
WARNING
Take care during this procedure. Sharp edges may be present that can cause injury.
1. Pull out tray 4.
2. Remove the rear cover, PL 70.26 Item 1.
3. Remove the paper feed assembly, Figure 1.
2
Remove 2
1 screws.
Disconnect the 2 in-line connectors
and the connector on the tray 4
home sensor.
Replacement
NOTE: New paper feeder assemblies come ready configured for use in tray 3. When a new
tray 4 paper feeder is required, follow the steps below.
1. If a new tray 4 paper feed assembly is being installed, perform steps 2 to 9. If the old tray
4 paper feed assembly is being re-installed, perform steps 5 to 9.
1
Locate both
tongues into the
frame slots.
2
Slide the support
bracket rearwards
and remove.
2
Install 2
screws.
1
Remove the screw.
3. Remove the tray 3 paper guide, REP 80.45. 6. Push tray 4 in slowly and check that the tray does not foul the paper feed assembly.
4. Install the tray 4 paper guide, REP 80.46. 7. Connect the four PJs, refer to Figure 1.
8. The remainder of the replacement is the reverse of the removal procedure. Refer to GP 6
before refitting the screws.
9. If a new paper feed assembly has been installed, reset the tray 4 feed roll HFSI count.
Refer to dC135 CRU/HFSI Status.
Problem:
Feed jams from the HCF tray. Cleaning the feed rolls or replacing them only temporarily
resolves the problem.
Cause:
Production based smooth surface Silicone nudger roll has difficulty feeding high fiber content
paper or paper with a high amount of clay filler. This will create excessive paper dust that
builds up and remains on the surface of the nudger roll.
Solution: Fixed! Did not fix.
Please provide feedback on this record, ONLY if you tried the information contained in the record.
Click on the Thumbs Up if this record helped you.
Click on the Thumbs Down if this record did not help you.
Install two feed rolls 655N50065 on the nudger roll shaft (PL 80.32 item 10, PL 80.33 item
12) as shown below. This type of roll has a textured surface that will better feed high dust
content paper.
pws://busrec/EKA-WorkCentre_5945f/X0884217156264180092769139230431073.dat?h... 22/09/2017
1341498.Feed jams from HCF, Trays 3 or 4 Pgina 2 de 2
ETI v1.5.0.0
pws://busrec/EKA-WorkCentre_5945f/X0884217156264180092769139230431073.dat?h... 22/09/2017