Documente Academic
Documente Profesional
Documente Cultură
INSTALLATION MANUAL
Applied Machines: /
<Important>
Be sure to correctly follow the procedures in order as explained in this Installation Manual.
If you do not follow the procedure in order, the image trouble may occur.
PF-P13 DK-P03*
WT-P02 KP-101
Machine
FS-P03 AU-201 MK-P02
FK-512* MK-738*
When installing the machine and associated options as a system, follow the order shown on the upper.
Note:
For the detailed installation procedures for each option, follow the instructions given in the corresponding
installation manual and perform the procedures correctly. (Optional devices must be installed after com-
pleting the main unit installation.)
Once the Power Switch is turned ON, do not turn OFF it until the installation work has been completed.
Caution:
Lifting the machine in an awkward position or transporting it in a poorly balanced position could result in
personal injury. When transporting the machine, assign an adequate number of persons to the job and
ensure that each person can take a good position of not being excessively loaded (mass: approx. 47.5 kg
(104-11/16 lb))
A3GN-9581-00
E-1
II. Installation space (unit: mm (inch)) III. Pre-installation check items
bizhub C3850 + PF-P13 + DK-P03 1. Select a level and stable place for installing the
machine.
2. Be sure to use a power source of the voltage and
809 (31-7/8)
frequency indicated in the product specifications.
555 254 Ensure that the current carrying capacity of the
(21-7/8) (10) power outlet is at least equal to the current listed
in the product specifications.
3. Power the machine directly from a dedicated
power outlet. (Do not use an extension cord.)
4. Do not plug or unplug the power cord with wet or
dirty hands, otherwise you may get an electric
shock.
5. Avoid a hot and humid environment, or a place
exposed to direct sunlight.
6. Avoid a dusty location, or a place near volatile
and flammable substances.
7. Avoid a poorly ventilated place.
1062 (41-13/16)
1014 (39-15/16)
884 48 IV. Notes on using touch panel
(34-13/16) (1-7/8) Be sure to instruct users on the following points.
This machine uses a capacitive touch panel.
(15-3/16) (28-7/8) (13-3/16)
E-2
V. Accessory parts Note:
This manual provides the illustrations of the acces-
No. Name Qty sory parts and machine that may be slightly differ-
1. Safety Information Guide 1 ent in shape from yours. In that case, instead of
the illustrations, use the appearance of your
2. Quick start guide 1 set machine to follow the installation procedure. This
3. Installation manual 1 set does not cause any significant change or problem
with the procedure.
4. Users guide CD 1
5. CD-ROM 1 set
6. Paper size label 1 set
VI. Unpacking the machine
7. Label (Legal restrictions on copying) * 1
1. Raise and remove the packing carton.
8. Label (Super G3 label) 1 2. Remove the accessory parts and cushions on the
9. Panel sheet 1 machine and open the plastic bag covering the
machine.
10. Power cord instruction * 1
3. Assign two or more persons and put their hands
11. Power cord 1 at the positions indicated in the illustration to
12. Modular cable * 1 raise the machine from the box, and place the
machine on the horizontal and robust place.
13. Cord clamp * 1
14. Cover A
17. Screw B
2
Note:
In case the FAX Kit is not included as the standard
equipment, keep the label (Super G3 label) at
hand. It is necessary for mounting the FAX Kit.
E-3
VII. Removing protective tape, packing 4. Slide the scanner lock lever to the unlock side
and close the ADF.
and other shipping materials
1. Remove tapes for protective sheet and get rid of
the protective sheet.
2. Remove all protective tapes and protective mate-
rials used for fixing the machine housing.
E-4
7. Hold the handle of the toner cartridge, then pull it 9. Check that the color of the toner cartridge
out. matches that of the insertion slot in the main unit,
then push the toner cartridge to the back.
Note:
Make sure that the toner cartridge is pushed all the
way in.
Electrical contacts
E-5
12. Remove protective films for the imaging units of 16. Remove the protective materials from the fusing
each color. section.
E-6
20. Slide out the tray 1 and remove the protective 3. Set paper with the printing side upward and slide
materials from the inside of the tray. the paper width guide to the paper size.
Note: Note:
Take care not to touch the surface of the paper Make sure that the top level of the paper stack
feed roller. If you touch it by mistake, wipe off any does not exceed the (MAX) paper level indica-
dirt on the roller surface using dry cloth. tor.
E-7
X. Connecting the power cord 4. Plug the power cord into the power outlet.
E-8
XII. Connecting the modular cable XIV. Notes when performing dial transfer
Note: Note:
This step may not be performed depending on the Refer to this chapter only if your machine comes
applicable marketing area. with the FAX function as standard.
Connect the supplied modular cable to the LINE After setting the fax target, dialing operations may
port. be selected after the switchboard dial tone is
detected depending on the destination. In this case,
depending on the switchboard connected to the
machine and the type of dial tone received from the
switchboard, dialing operations may not be avail-
able. If that happens, you may be able to avoid the
problem with the following setting.
E-9
XV. Affixing the labels 4. Affix the supplied panel sheet to the surface of
the operation panel.
1. Affix the label (Legal restrictions on copying) to
Note:
the position shown below.
The panel sheet is affixed on customer request.
Note: The panel sheet must be kept by the customer.
This step may not be performed depending on the
applicable marketing area.
E-10