Documente Academic
Documente Profesional
Documente Cultură
com
Accessory Application Publications No.
AII 31723
INSTALLATION FOG LIGHTS FIT
Issue Date
INSTRUCTIONS MAR 2006
PARTS LIST
Fuse (20A)
Switch harness
Template
Fuse label
Fog light switch
Relay
2 Clip nuts
2 Special screws
2 Clips
11 Wire ties
© 2006 American Honda Motor Co., Inc. - All Rights Reserved. AII 31723 (0603) 08V31-SLN-3000-93 1 of 13
TOOLS REQUIRED INSTALLATION
Phillips screwdriver Customer information: The information in this
Flat-tip screwdriver installation instruction is intended for use only by
Ratchet wrench (8 mm, 10 mm box) skilled technicians who have the proper tools,
equipment, and training to correctly and safely add
Drill
equipment to your vehicle. These procedures
Drill bits (3 mm, 5.5 mm) should not be attempted by “do-it-yourselfers”.
Utility knife
NOTE: Be extremely careful not to damage the front
File bumper or any other finished surfaces of the body.
Hacksaw blade
1. Make sure you have the anti-theft code for the
Felt-tip pen radio, then write down the frequencies for the
Hole saw (20 mm) preset buttons.
Shop towel
2. Disconnect the negative cable from the battery.
Isopropyl alcohol
Cutting the Front Bumper
Pushpin
Eye protection 3. Open the hood. Remove the front bumper (eight
Scissors clips and four self-tapping screws). To prevent
damage, set the front bumper on a blanket.
Blanket
Masking Tape NOTE: Have an assistant help you when removing
and installing the front bumper.
Illustration of the Fog Lights Installed on the
Vehicle
FUSE
SWITCH
RELAY HARNESS
SWITCH
2 of 13 AII 31723 (0603) © 2006 American Honda Motor Co., Inc. - All Rights Reserved.
4. Remove the left front bumper side vent (three 6. On the outside of the front bumper, place the left
hooks). template along the front bumper and tape it in
place.
HOOKS
(3) SQUARE HOLES (2)
FRONT
BUMPER
MASKING TAPE
Put two tabs
into the square
holes.
“L” MARK
TEMPLATE “L”
5919020H
FELT-TIP
PEN
5D06011H
© 2006 American Honda Motor Co., Inc. - All Rights Reserved. AII 31723 (0603) 3 of 13
10. To protect the front bumper, apply masking tape in 13. Locate the dimple on the front bumper. While
the area shown. wearing eye protection, drill a 5.5 mm hole through
the dimple. Start with a 3 mm drill bit, and finish
PUSHPIN
MARKS (6) with a 5.5 mm drill bit.
MASKING TAPE
MASKING TAPE
DIMPLE
HOLESAW
FRONT
(First drill with a 3 mm
BUMPER
bit, and finish with a 20
mm bit or holesaw.)
5919052H
10 mm
DRILL
(3 mm 5.5 mm bit)
11. While wearing eye protection, drill six 20 mm
holes through the marks you just made. MASKING TAPE 5919070H
HACKSAW
(Be extremely careful
not to cut the bumper
5919062H
more than necessary.)
CLIP
INNER
FENDER
TAB
Pull down.
5030010H
4 of 13 AII 31723 (0603) © 2006 American Honda Motor Co., Inc. - All Rights Reserved.
16. Inside the left fender area, locate the 1-pin 19. Secure the fog light subharness to the vehicle
connector blue-taped to the vehicle harness. frame and panel hole using the two wire ties with
Remove the blue tape to free the connector. clips at the green-taped locations.
FOG LIGHT
SUBHARNESS
VEHICLE
HARNESS
FRAME HOLE
WIRE TIE
WITH CLIP
VEHICLE
1-PIN FRAME HOLE
CONNECTOR
GREEN
TAPE
FOG LIGHT
SUBHARNESS
WIRE TIE
FOG LIGHT BLUE TAPE WITH CLIP
5920021H
SUBHARNESS VEHICLE (Remove.) GREEN
1-PIN CONNECTOR HARNESS TAPE
5919091H
FOG LIGHT
SUBHARNESS
WIRE
TIE
VEHICLE
GROUND BOLT
(Reuse.) 5919102H
FRAME
FOG LIGHT
SUBHARNESS
GROUND TERMINAL 5920010H
© 2006 American Honda Motor Co., Inc. - All Rights Reserved. AII 31723 (0603) 5 of 13
Routing the Fog Light Harness 24. Route the fog light harness along the front bumper
to the right side of the vehicle and attach the five
21. On the inside of the front bumper on the left side,
fog light harness clips to the five ribs inside the
place the narrowed portion of the fog light harness
front bumper.
between the air screen and the front bumper.
AIR
SCREEN
LEFT SIDE OF FOG LIGHT
HARNESS 4-PIN AIR
FRONT SCREEN
BUMPER CONNECTOR
AIR SCREEN
HOLE
FOG
LIGHT
HARNESS
22. Attach the wire tie with holder to the fog light 26. Attach one clip to the fog light harness at the
harness 4-pin connector, and route it through the green tape, then secure the clip to the front
air screen holes. bumper opening as shown.
FRONT CLIP
BUMPER
OPENING
GREEN
TAPE
GREEN
TAPE
FOG LIGHT
HARNESS
5N29040H
FOG LIGHT
HARNESS
5920040H
6 of 13 AII 31723 (0603) © 2006 American Honda Motor Co., Inc. - All Rights Reserved.
27. Reinstall the front bumper side vents. Routing the Switch Harness
33. Remove the driver’s dashboard under cover:
CLIP NUT • Turn the knob clockwise.
• Release the clip and the pin.
FOG LIGHT
HARNESS
2-PIN
CONNECTOR
SPECIAL
SCREW
FRONT BUMPER
SIDE VENT
RETAINING TAB
28. Attach one clip nut to the 5.5 mm hole made in DRIVER’S
step 13. Plug the fog light harness 2-pin DASHBOARD
UNDER COVER 5914010K
connecter to the left fog light. KNOB
WEATHERSTRIP
FRONT
BUMPER
DRIVER’S
KICK
PANEL
FOG LIGHT CLIPS (2)
SUBHARNESS
5914020K
FOG LIGHT 4-PIN
HARNESS 4-PIN CONNECTOR
CONNECTOR 5030020H
© 2006 American Honda Motor Co., Inc. - All Rights Reserved. AII 31723 (0603) 7 of 13
35. Remove the fuse box cover: 38. Plug the 4-pin relay into the switch harness relay
block, then slide the relay block onto the vehicle
• Turn the knob counterclockwise.
relay block on the right side of the fuse box.
• Release the five clips and the three retaining VEHICLE
tabs. FUSE BOX
HARNESS
CLIPS (5)
5-PIN
CONNECTOR
SWITCH
HARNESS
4-PIN RELAY
FUSE BOX
COVER
RETAINING
TABS (3) Front View 5921022H
SWITCH HARNESS
KNOB RELAY BLOCK
5914030K
SWITCH HARNESS
5-PIN CONNECTOR
5-PIN
CONNECTOR
8 of 13 AII 31723 (0603) © 2006 American Honda Motor Co., Inc. - All Rights Reserved.
40. Install the 20A fuse into the number 20 slot in the 43. Plug the switch harness 13-pin connector into
fuse box. the mirror switch. Plug the vehicle mirror switch
13-pin connector into the switch harness 13-pin
connector.
Front View
FUSE LOCATION
(Number 20 slot)
MIRROR
SWITCH
VEHICLE
SWITCH HARNESS VEHICLE
HARNESS 13-PIN
CONNECTOR
SWITCH
HARNESS
13-PIN
CONNECTOR
SWITCH HARNESS
WIRE TIES (3) 13-PIN CONNECTOR
20A FUSE
5921051H
VEHICLE
13-PIN
CONNECTOR SWITCH
HARNESS
WIRE TIE
5921060H
© 2006 American Honda Motor Co., Inc. - All Rights Reserved. AII 31723 (0603) 9 of 13
46. Unplug the vehicle 20-pin connector from the lower 49. Secure the 20-pin connector to the vehicle
left side of the fuse box, and plug the switch harness using two wire ties connected together.
harness 20-pin connector into the fuse box.
2-PIN
CONNECTORS
FUSE BOX
WIRE
TIE
20-PIN CONNECTORS
Front View
SWITCH VEHICLE 20-PIN
HARNESS CONNECTOR 5921071H TWO WIRE TIES
20-PIN
(Connect as shown.)
CONNECTOR
5922011H
BLUE TAPE
(Remove.)
FUSE
BOX
VEHICLE 2-PIN
CONNECTOR
SWITCH HARNESS
2-PIN CONNECTOR
5921081H
10 of 13 AII 31723 (0603) © 2006 American Honda Motor Co., Inc. - All Rights Reserved.
51. Check that all wire harnesses are routed properly USE AND CARE
and all connectors are plugged in.
How to Operate Fog Lights
52. Reinstall all removed parts. Check that all clips
NOTE: The fog light lenses can cloud when the outside
and fasteners are installed securely.
temperature is cold; this is normal and should go away
53. Reconnect the negative cable to the battery. in warm weather.
54. Reset the clock, and reset the radio station • Turn the light switch to the “ ” position (headlights
presets. on low beam).
NOTE: When the battery is disconnected, the driver’s • Press the fog light switch (indicator on).
window AUTO function is disabled.
• If the fog lights don’t come on, check the fuse and
• Start the engine. Push down on the driver’s all the connectors, including the ground cable.
window switch until the window is fully open.
Fog Light Aiming Adjustment
• Pull up on the driver’s window switch to close the
• Adjust the aiming according to local laws and
window completely, then hold the switch for 2
regulations.
seconds or more.
• To adjust, turn the aiming adjustment screw in or
• Lower and raise the driver’s window to check
out until the correct aiming is obtained.
operation of the driver’s window AUTO function.
To lower.
To raise.
Lower View
5922050H
© 2006 American Honda Motor Co., Inc. - All Rights Reserved. AII 31723 (0603) 11 of 13
BULB REPLACEMENT 4. Install the new bulb and socket to the fog light.
1. Remove a self-tapping screw and a clip, and then • Use only a genuine Honda halogen light bulb
pull back the inner fender. of specified wattage.
Rating: 12V 55W H11 Halogen Light Bulb P/N
33165-S5A-003
• Do not touch the bulb. Oily or greasy
substances on the bulb can shorten its service
life due to the heat produced when the bulb is
turned on. If the bulb is accidentally touched,
wipe it clean with a soft cloth that has been
dampened with a denatured alcohol or a mild
detergent solution.
• Align the tab on the fog light with the cutout in
the bulb when installing the new bulb. If not
aligned, the fog light may annoy oncoming
drivers.
FOG LIGHT
2. Unplug the connector from the fog light.
3. Remove the bulb.
FOG LIGHT
BULB
CONNECTOR
5922030H
12 of 13 AII 31723 (0603) © 2006 American Honda Motor Co., Inc. - All Rights Reserved.
UNDER-HOOD UNDER-DASH
FUSE/RELAY BOX FUSE/RELAY BOX
BATTERY
No.1 (80A) No.7 (30A) No.20 (20A)
RED
BLU/
RED
FRONT
FOG LIGHT
RED/BLK RELAY
BLU/YEL
BLU/RED
LIGHT
INDICATOR
LIGHT LEFT
FRONT
FOG RIGHT
LIGHT
RED RED/WHT
BLK
OFF - - - -
WHT WHITE GRY GRAY
- - ON - LT BLU LIGHT BLUE LT GRN LIGHT GREEN
5922061H
© 2006 American Honda Motor Co., Inc. - All Rights Reserved. AII 31723 (0603) 13 of 13