Sunteți pe pagina 1din 337

JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

CONTENTS

1 INTRODUCTION.............................................................................1-1
2 SAFETY PRECAUTIONS...............................................................2-1
2.1 Fire..............................................................................................2-1
2.1.1 The Fire Triangle..........................................................2-2
2.1.2 Classes of Fire...............................................................2-2
2.1.3 Fire Extinguishants and their Uses................................2-3
2.2 First Aid......................................................................................2-5
2.3 Workshop and Hangar Safety...................................................2-5
2.3.1 Machinery......................................................................2-5
2.3.2 Electricity.......................................................................2-6
2.3.3 Noise.............................................................................2-7
2.3.4 High-Pressure Gases....................................................2-7
2.3.5 Gas Bottle Identification.................................................2-8
2.3.6 High-Pressure Gas Replenishing...................................2-8
2.3.7 Oxygen Systems............................................................2-9
2.3.8 Aviation Oils and Fuels..................................................2-10
2.3.9 Chemical and Physiological Hazards.............................2-11
2.3.10 Lifting and Shoring.........................................................2-11
2.3.11 Slinging..........................................................................2-12
2.4 Flight-Line Safety......................................................................2-13
2.4.1 Towing and Taxying.......................................................2-14
2.4.2 Parking..........................................................................2-15
2.4.3 Marshalling....................................................................2-16
2.4.4 Fuelling..........................................................................2-17
2.4.5 Weather Radar..............................................................2-18
3 WORKSHOP PRACTICES.............................................................3-1
3.1 Care of Tools..............................................................................3-1
3.2 Control of Tools.........................................................................3-2
3.3 Calibration of Tools and Equipment........................................3-3
3.3.1 General Notes on Calibration.........................................3-3
3.3.2 Procedures....................................................................3-4
3.4 Use of Workshop Materials.......................................................3-6
3.5 Standards of Workmanship......................................................3-7
4 TOOLS............................................................................................4-1
4.1 Common Hand Tools.................................................................4-1
4.1.1 Engineers Rule.............................................................4-1
4.1.2 Scriber...........................................................................4-2
4.1.3 Key-Seat Rule................................................................4-2
4.1.4 Fitters Square...............................................................4-3
4.1.5 Combination Set............................................................4-4
4.1.6 Surface Plates and Tables.............................................4-5
4.1.7 V Blocks.........................................................................4-5
4.1.8 Surface Gauge (Scribing Block).....................................4-6
4.1.9 Dividers..........................................................................4-7
4.1.10 Callipers.........................................................................4-7
4.1.11 Hammers.......................................................................4-8

370280148.doc Issued December 2002 Page 1


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

4.1.12 Punches.........................................................................4-9
4.1.13 Metal-Cutting Chisels.....................................................4-10
4.1.14 Bench Vice....................................................................4-12
4.1.15 Hand Vice......................................................................4-13
4.1.16 Hacksaws......................................................................4-14
4.1.17 Sheet Metal Shears and Snips......................................4-15
4.1.18 Files...............................................................................4-16
4.1.19 Filing Techniques...........................................................4-19
4.1.20 Hand Brace (Hand Drill).................................................4-21
4.1.21 Twist Drills.....................................................................4-22
4.1.22 Stop, and Press (Dimpling), Countersinking Tools.........4-27
4.1.23 Reamers........................................................................4-29
4.1.24 Internal Screw Thread, Cutting Taps..............................4-32
4.1.25 External Screw Thread, Cutting Dies.............................4-34
4.1.26 Screwdrivers..................................................................4-36
4.1.27 Pliers..............................................................................4-38
4.1.28 Wire Snips (Nippers)......................................................4-39
4.1.29 Spanners, Sockets and Wrenches.................................4-39
4.2 Common Power Tools...............................................................4-45
4.2.1 Electrically Powered Pillar Drills.....................................4-45
4.2.2 Electrically Powered Hand Drills....................................4-46
4.2.3 Pneumatically Powered Hand Drills...............................4-46
4.2.4 Pneumatically Powered Riveting Hammers...................4-48
4.2.5 Pneumatic Miller (Microshaver).....................................4-49
4.2.6 Nibblers.........................................................................4-49
4.2.7 Pneumatic Tool Maintenance.........................................4-50
4.2.8 Abrasive Wheels............................................................4-50
4.3 Precision Measuring Instruments............................................4-52
4.3.1 External Micrometers.....................................................4-52
4.3.2 Internal Micrometers......................................................4-56
4.3.3 Micrometer Depth Gauge...............................................4-57
4.3.4 Vernier Micrometers.......................................................4-58
4.3.5 Vernier Callipers............................................................4-60
4.3.6 Vernier Height Gauge....................................................4-61
4.3.7 Vernier Protractor...........................................................4-62
4.4 Miscellaneous Measuring Tools...............................................4-63
4.4.1 Gauge Blocks................................................................4-63
4.4.2 Dial Test Indicator (DTI).................................................4-64
4.4.3 Feeler Gauges...............................................................4-64
4.4.4 Screw Pitch and Radius Gauges...................................4-65
4.4.5 Go/No-Go Gauges.........................................................4-65
4.4.6 Straight Edges...............................................................4-65
4.5 Lubrication Methods and Equipment.......................................4-66
4.5.1 Lubrication Methods......................................................4-66
4.5.2 Lubrication Equipment...................................................4-69
5 ENGINEERING DRAWING, DIAGRAMS AND STANDARDS.......5-1
5.1 Types of Drawing.......................................................................5-1
5.2 Methods of Drawing Solid Objects...........................................5-2
5.2.1 Pictorial Projections.......................................................5-3
5.2.2 Orthographic Projections...............................................5-4

Page 2 370280148.doc Issued December 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

5.2.3 Sectional Views.............................................................5-5


5.2.4 Exploded Views.............................................................5-6
5.2.5 Drawing Lines, Symbols and Abbreviations...................5-7
5.2.6 Conventional Representations.......................................5-9
5.2.7 General and Geometric Tolerances...............................5-9
5.3 Drawing Identification System.................................................5-10
5.3.1 Title Block......................................................................5-11
5.3.2 Drawing Number............................................................5-11
5.3.3 Handed Parts.................................................................5-11
5.3.4 Sheet Numbers..............................................................5-11
5.3.5 Drawing Changes..........................................................5-11
5.3.6 Part Referencing............................................................5-12
5.3.7 Validation of Modification/Repair Drawings....................5-12
5.3.8 Summary of Recommended Drawing Information.........5-13
5.4 Auxiliary Diagrams and Charts................................................5-14
5.4.1 Electical Wiring Diagrams..............................................5-14
5.4.2 Component Location Diagrams.....................................5-15
5.4.3 Schematic Diagrams......................................................5-16
5.4.4 Block Diagrams..............................................................5-17
5.4.5 Logic Flowcharts............................................................5-17
5.5 Microfilm, Microfiche and Computerised Presentations........5-19
5.5.1 Microfilm........................................................................5-19
5.5.2 Microfiche......................................................................5-19
5.5.3 Computer CD-ROM.......................................................5-20
5.5.4 Supplementary Information............................................5-20
5.6 Aeronautical Standards............................................................5-21
5.6.1 Air Transport Association Specification No. 100.............5-21
5.6.2 International Organisation for Standardisation (ISO)......5-24
5.6.3 British Standards (BS)...................................................5-24
5.6.4 Military Standard (MS)...................................................5-24
5.6.5 Air Force and Navy (AN)................................................5-24
5.6.6 National Aerospace Standard (NAS)..............................5-24
6 FITS AND CLEARANCES..............................................................6-1
6.1 Dimensions................................................................................6-1
6.1.1 Allowances....................................................................6-1
6.1.2 Tolerances.....................................................................6-2
6.2 Drilling Sizes for Holes.............................................................6-3
6.3 Classes of Fits...........................................................................6-3
6.3.1 Newall System...............................................................6-4
6.3.2 British Standards System...............................................6-5
6.4 Schedule of Fits and Clearances.............................................6-5
6.4.1 Limits for Wear...............................................................6-6
6.4.2 Limits for Ovality............................................................6-6
6.4.3 Limits for Bow................................................................6-7
6.4.4 Limits for Twist...............................................................6-8
7 RIVETING........................................................................................7-1
7.1 Types of Solid Rivet..................................................................7-1
7.1.1 Rivet Materials...............................................................7-2
7.1.2 Basic Rivet Location Terminology..................................7-2

370280148.doc Issued December 2002 Page 3


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

7.2 Types of Riveted Joints.............................................................7-4


7.3 Closing Solid Rivets..................................................................7-4
7.4 Closing Hollow Rivets...............................................................7-5
7.4.1 Tucker-pop.....................................................................7-5
7.4.2 Chobert..........................................................................7-5
7.4.3 Avdel..............................................................................7-6
7.4.4 Cherry Max....................................................................7-7
7.4.5 Hi-Lok............................................................................7-8
7.4.6 Rivnuts...........................................................................7-8
7.5 Inspection of Riveted Joints.....................................................7-9
7.6 Rivet Removal Procedure.........................................................7-10
8 PIPES AND HOSES........................................................................8-1
8.1 Pipe Bending.............................................................................8-1
8.1.1 Simple Bending Jigs......................................................8-2
8.1.2 Hand Pipe-Bending Machines.......................................8-2
8.2 Pipe Flaring................................................................................8-3
8.2.1 Flaring Tool....................................................................8-3
8.2.2 Standard Flared Pipe Couplings....................................8-4
8.2.3 Flareless Couplings.......................................................8-5
8.3 Inspection and Testing of Pipes and Hoses............................8-6
8.3.1 Bore Testing of Pipes.....................................................8-7
8.3.2 Hydraulic Pressure Testing of Pipes..............................8-7
8.3.3 Pneumatic and Oxygen Pressure Testing of Pipes........8-7
8.3.4 Cleaning After Test.........................................................8-7
8.3.5 Testing Flexible Hoses...................................................8-8
8.4 Installation and Clamping of Pipes..........................................8-8
8.4.1 Pipe Supports................................................................8-8
8.5 Connection of Pipes..................................................................8-9
8.6 Maintenance of Pipes and Hoses.............................................8-9
8.7 Pipe Identification Tape.............................................................8-10
9 SPRINGS........................................................................................9-1
9.1 Inspection and Testing of Springs...........................................9-1
10 BEARINGS......................................................................................10-1
10.1 Cleaning and Inspection of Bearings.......................................10-1
10.2 Inspection of Bearings..............................................................10-2
10.2.1 Normal Fatigue..............................................................10-2
10.2.2 Excessive Loads............................................................10-2
10.2.3 Installation and Misalignment.........................................10-3
10.2.4 Loose Fit........................................................................10-3
10.2.5 Brinelling........................................................................10-3
10.2.6 Overheating and Lubrication Failure..............................10-4
10.2.7 Contamination and Corrosion........................................10-5
10.3 Safety Precautions....................................................................10-5
10.4 Storage.......................................................................................10-5
11 TRANSMISSIONS..........................................................................11-1
11.1 Gears..........................................................................................11-1
11.2 Belts and Pulleys.......................................................................11-1

Page 4 370280148.doc Issued December 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

11.3 Chains and Sprockets...............................................................11-2


11.4 Screw Jacks...............................................................................11-3
11.5 Levers.........................................................................................11-4
11.5.1 Push-Pull Rod Systems.................................................11-5
12 CONTROL CABLES.......................................................................12-1
12.1 Swaging of End Fittings............................................................12-1
12.2 Inspection and Testing of Control Cables...............................12-1
12.2.1 Cable Wear....................................................................12-1
12.2.2 Bowden and Teleflex Cable Systems.............................12-3
12.3 Inspection of Control Cable Pulleys........................................12-4
13 SHEET METAL WORK...................................................................13-1
13.1 Marking Out...............................................................................13-2
13.2 Forming of Sheet Metal Parts...................................................13-3
13.2.1 Cutting...........................................................................13-3
13.2.2 Bending and Calculation of Bend Allowance..................13-4
13.3 Inspection of Sheet Metal Work................................................13-8
14 WELDING, SOLDERING AND BONDING.....................................14-1
14.1 Welding......................................................................................14-1
14.2 Methods of Welding..................................................................14-1
14.2.1 Oxy-Acetylene Flame....................................................14-1
14.2.2 Manual Metal Arc...........................................................14-2
14.2.3 Metal Arc Gas-Shielded (MAGS)...................................14-2
14.2.4 Tungsten Arc Gas-Shielded (TAGS)..............................14-2
14.2.5 Flash Butt Welding.........................................................14-3
14.2.6 Spot Welding.................................................................14-3
14.2.7 Seam Welding...............................................................14-3
14.3 Inspection and Testing of Welds..............................................14-3
14.4 Soldering....................................................................................14-4
14.5 Methods of Soldering................................................................14-4
14.5.1 Hard Soldering (Brazing and Silver Soldering)...............14-4
14.5.2 Soft Soldering................................................................14-5
14.5.3 Using Indirectly Heated (Electric) Soldering Irons..........14-6
14.5.4 Active and Passive Fluxes.............................................14-8
14.5.5 Flux Removal.................................................................14-10
14.6 Inspection and Testing of Soldered Joints..............................14-10
14.7 Bonding......................................................................................14-10
14.8 Methods of Bonding..................................................................14-11
14.8.1 Thermoplastic Adhesives...............................................14-11
14.8.2 Thermosetting Adhesives...............................................14-12
14.9 Inspection and Testing of Bonded Joints................................14-12
15 AIRCRAFT MASS AND BALANCE...............................................15-1
15.1 Definitions..................................................................................15-1
15.2 Mass and Balance.....................................................................15-2
15.2.1 Mass and Balance Documentation................................15-3
15.3 Frequency of Weighing.............................................................15-4
15.3.1 Fleet Mass and CG Position..........................................15-4

370280148.doc Issued December 2002 Page 5


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

15.4 Weighing Requirements............................................................15-4


15.5 Centre of Gravity Limits (CG Envelope)..................................15-5
15.6 Records......................................................................................15-5
15.7 Calculation of Mass and CG of any System............................15-5
15.8 Principles of Weight and Balance of Aircraft..........................15-7
15.9 Calculation of Mass and CG of Aircraft...................................15-7
15.10 Aircraft Weighing Methods.......................................................15-8
15.10.1 Preparation for Weighing...............................................15-9
15.10.2 Weighing on Aircraft Jacks.............................................15-9
15.10.3 Calculation of Aircrafts CG............................................15-10
15.10.4 CG as Percentage Standard Mean Chord (SMC)..........15-12
15.11 Changes in Basic Weight..........................................................15-12
15.11.1 Examples of Alterations to Dry Operating Mass.............15-13
15.12 Loading of Aircraft (Typical Aircraft Load Sheet)....................15-15
16 AIRCRAFT HANDLING AND STORAGE......................................16-1
16.1 Moving Methods........................................................................16-2
16.1.1 Moving by Hand and Steering Arm................................16-2
16.1.2 Using a Bridle and Steering Arm....................................16-2
16.1.3 Using a Purpose-Made Towing Arm...............................16-3
16.1.4 Precautions when Towing Aircraft..................................16-3
16.1.5 Taxiing Aircraft...............................................................16-4
16.2 Aircraft Jacking.........................................................................16-5
16.2.1 Special Considerations..................................................16-5
16.2.2 Aircraft Jacks.................................................................16-6
16.2.3 Jack Maintenance and General Notes...........................16-7
16.2.4 Jacking Precautions.......................................................16-8
16.2.5 Jacking Procedures.......................................................16-8
16.2.6 Trestles..........................................................................16-9
16.2.7 Lowering Aircraft off Jacks.............................................16-10
16.3 Slinging......................................................................................16-10
16.3.1 Lifting Tackle..................................................................16-11
16.4 Parking and Mooring Aircraft...................................................16-12
16.4.1 Parking..........................................................................16-12
16.4.2 Mooring (Picketing)........................................................16-13
16.4.3 Typical Small Aircraft Procedures..................................16-14
16.4.4 Large Aircraft Procedures..............................................16-14
16.4.5 Chocking of Aircraft........................................................16-15
16.5 Aircraft Storage.........................................................................16-16
16.6 Aircraft Fuelling Procedures....................................................16-20
16.6.1 Fuelling Safety Precautions...........................................16-20
16.6.2 Refuelling.......................................................................16-21
16.6.3 Checking Fuel Contents.................................................16-21
16.6.4 Defuelling.......................................................................16-22
16.7 Ground De-Icing/Anti-Icing of Aircraft.....................................16-23
16.7.1 Ice Types.......................................................................16-23
16.7.2 Definitions......................................................................16-25
16.7.3 De-Icing and Anti-Icing Methods....................................16-25
16.7.4 Chemical De-Icing.........................................................16-26

Page 6 370280148.doc Issued December 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

16.7.5 Treatment of Frost Deposits...........................................16-26


16.7.6 Removal of Ice and Snow Deposits...............................16-27
16.7.7 Hold Over Times............................................................16-29
16.7.8 Inspection after De-Icing/Anti-Icing Procedures.............16-30
16.8 Ground Electrical Supplies.......................................................16-31
16.9 Ground Hydraulic Supplies......................................................16-33
16.9.1 Safety, Health and Servicing Precautions......................16-33
16.9.2 Rig Maintenance............................................................16-34
16.10 Ground Pneumatic Supplies.....................................................16-34
16.11 Effects of Environmental Conditions on Handling.................16-35
16.11.1 Cold and Wet.................................................................16-35
16.11.2 Snow and Ice.................................................................16-36
16.11.3 High Winds....................................................................16-36
16.11.4 High Temperature..........................................................16-37
17 PREVENTATIVE MAINTENANCE TECHNIQUES.........................17-1
17.1 Types of Defects........................................................................17-1
17.1.1 External Damage...........................................................17-2
17.1.2 Inlets and Exhausts.......................................................17-3
17.1.3 Liquid Systems..............................................................17-3
17.1.4 Gaseous Systems..........................................................17-4
17.1.5 Dimensions....................................................................17-5
17.1.6 Tyres..............................................................................17-5
17.1.7 Wheels...........................................................................17-6
17.1.8 Brakes...........................................................................17-6
17.1.9 Landing Gear Locks.......................................................17-7
17.1.10 Indicators.......................................................................17-7
17.1.11 External Probes.............................................................17-8
17.1.12 Handles and Latches.....................................................17-8
17.1.13 Panels and Doors..........................................................17-8
17.1.14 Emergency System Indication.......................................17-9
17.1.15 Lifed Items.....................................................................17-9
17.1.16 Light Bulbs.....................................................................17-9
17.1.17 Permitted Defects..........................................................17-9
17.2 Locations of Corrosion in Aircraft...........................................17-10
17.2.1 Exhaust Areas...............................................................17-10
17.2.2 Engine Intakes and Cooling Air Vents............................17-10
17.2.3 Landing Gear.................................................................17-10
17.2.4 Bilge and Water Entrapment Areas................................17-11
17.2.5 Recesses in Flaps and Hinges......................................17-11
17.2.6 Magnesium Alloy Skins..................................................17-11
17.2.7 Aluminium Alloy Skins....................................................17-11
17.2.8 Spot-Welded Skins and Sandwich Constructions..........17-12
17.2.9 Electrical Equipment......................................................17-12
17.2.10 Control Cables...............................................................17-12
17.3 Corrosion Removal, Assessment and Reprotection..............17-13
17.3.1 Cleaning and Paint Removal.........................................17-13
17.3.2 Ferrous Metals...............................................................17-14
17.3.3 Aluminium and Aluminium Alloys...................................17-14
17.3.4 Alclad.............................................................................17-15
17.3.5 Magnesium Alloys..........................................................17-16

370280148.doc Issued December 2002 Page 7


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

17.3.6 Acid Spillage..................................................................17-16


17.3.7 Alkali Spillage................................................................17-16
17.3.8 Mercury Spillage............................................................17-17
17.4 Permanent Anti-Corrosion Treatments....................................17-18
17.4.1 Electro-Plating...............................................................17-18
17.4.2 Sprayed Metal Coatings.................................................17-18
17.4.3 Cladding........................................................................17-18
17.4.4 Surface Conversion Coatings........................................17-19
17.5 Non-Destructive Testing/Inspection (NDT/NDI) Techniques. .17-20
17.5.1 Visual/Assisted Visual Inspections.................................17-21
17.5.2 Remote Viewing Instruments.........................................17-22
17.5.3 Penetrant Flaw Detection (PFD)....................................17-25
17.5.4 Ultrasonic Flaw Detection (UFD)....................................17-34
17.5.5 Eddy Current Flaw Detection (ECFD)............................17-40
17.5.6 Magnetic Particle Flaw Detection (MPFD).....................17-46
17.5.7 Radiographic Flaw Detection (RFD)..............................17-52
17.5.8 Miscellaneous Radiation Techniques.............................17-57
17.6 Disassembly and Re-assembly Techniques............................17-58
17.6.1 Complete Airframes.......................................................17-58
17.6.2 Replacement of Major Components/Modules................17-59
17.6.3 Replacement of Minor Components/Modules................17-60
17.6.4 Disassembly and Re-assembly of Major Components...17-60
17.6.5 Disassembly and Re-assembly of Minor Components...17-60
17.6.6 Basic Disassembly and Re-assembly Techniques.........17-61
17.6.7 Small Part and Component Identification.......................17-62
17.6.8 Discarding of Parts........................................................17-63
17.6.9 Freeing Seized Components.........................................17-63
17.6.10 Use of Correct Tools......................................................17-63
17.6.11 Murphys Law...............................................................17-64
18 ABNORMAL EVENTS....................................................................18-1
18.1 Types of abnormal occurrences...............................................18-1
18.2 Types of damage.......................................................................18-1
18.3 Lightning Strikes.......................................................................18-2
18.3.1 Effects of a Lightning Strike...........................................18-2
18.3.2 Inspection......................................................................18-2
18.4 Example of a Post Lightning Strike Procedure.......................18-3
18.4.1 Basic Protection.............................................................18-3
18.4.2 Strike Areas...................................................................18-4
18.4.3 Signs of Damage...........................................................18-5
18.4.4 External Components at Risk........................................18-5
18.4.5 Electrical Components at Risk.......................................18-6
18.4.6 Examination of External Surface....................................18-6
18.4.7 Functional Tests.............................................................18-7
18.4.8 Examination of Internal Components.............................18-8
18.4.9 Return the Aircraft to Service.........................................18-9
18.5 High Intensity Radiated Fields (HIRF) Penetration.................18-9
18.5.1 Specific Testing HIRF..................................................18-10
18.5.2 Protection against HIRF Interference.............................18-11
18.6 Heavy Landings.........................................................................18-12

Page 8 370280148.doc Issued December 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

18.6.1 Example of Post Heavy Landing Inspection...................18-12


18.7 Flight through Severe Turbulence............................................18-14
19 MAINTENANCE PROCEDURES...................................................19-1
19.1 Maintenance Planning...............................................................19-1
19.2 Modification Procedures...........................................................19-2
19.2.1 Major Modifications........................................................19-2
19.2.2 Minor Modifications........................................................19-2
19.3 Stores Procedures.....................................................................19-3
19.4 Certification and Release Procedures.....................................19-3
19.4.1 Interface with Aircraft Operation.....................................19-4
19.5 Maintenance Inspection/ Quality Control and Assurance....19-5
19.6 Additional Maintenance Procedures........................................19-6
19.7 Control of Life-Limited Components.......................................19-6

370280148.doc Issued December 2002 Page 9


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

PAGE
INTENTIONALLY
BLANK

Page 10 370280148.doc Issued December 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

1 INTRODUCTION

Most accidents are, in the main, caused by human carelessness and accidents in
the work place are among the main causes of death and disability.

They are, additionally, the cause of a great loss of man-hours and, thus, cost
companies (and individuals) large amounts of money.

All personnel should be aware, not only of the potential for accidents and injury,
wherever they work, but also of the legislation and information that is available in
an attempt to prevent accidents actually happening.

While it is incumbent upon companies (in accordance with The Management of


Health and Safety at Work Regulations 1992), to ensure that all personnel
receive adequate training in Health and Safety matters, this Module contains a
reminder of some of the general safety precautions which are necessary, when
working in the aerospace industry.

The Module continues with further topics, which are concerned with the practices
recommended for the safe and efficient maintenance of aircraft and aerospace
components.

370280148.doc Issued December 2002 Page 1


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

Page 2 370280148.doc Issued December 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

2 SAFETY PRECAUTIONS

Aircraft, by their very nature and design, make for a dangerous working
environment. The danger is further increased by the wide variety of machines,
tools and materials required to support and maintain aircraft.

Personal safety starts with being appropriately dressed for the work being
undertaken, combined with the correct use of eye and ear protection whenever
necessary.

Technicians should only operate equipment with which they are familiar and
which they can operate safely. Hand tools should be kept in good working order.

Good housekeeping in workshops, hangars, and on flight line ramps is essential


to safe and efficient maintenance.

Pedestrian and fire lanes should be clearly marked and NEVER obstructed. They
should always be used to keep non-technical personnel clear from the work area.

Any spillage of oils, greases and fuels should be immediately covered with
absorbent material and cleaned up, to prevent fire or injury. Spillage should be
prevented, from running into floor drains.

It is very important, that all personnel know the location of the fixed points where
fire fighting equipment and First Aid treatment are available. They must also be
aware of the types of emergency that can occur in the workplace (whether in the
workshop, hangar or on the ramp), and of the procedures to be followed in any
emergency.

2.1 Fire

WARNING: ALWAYS ENSURE THAT CORRECT FIRE PRECAUTIONS ARE


OBEYED AND THAT ESCAPE ROUTES ARE NOT OBSTRUCTED. LETHAL
FUMES AND SMOKE CAN BE PRODUCED BY CERTAIN MATERIALS AND
THEY CAN BURN VERY RAPIDLY.

Personnel, engaged in the maintenance, overhaul and repair of aircraft, should


be fully conversant with the precautions required to prevent outbreaks of any fire.
They should be qualified in the operation of any fire protection equipment that is
provided, and should know the action to be taken in the event of discovering a
fire.

370280148.doc Issued December 2002 Page 1


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

Page 2 370280148.doc Issued December 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

2.1.3 Fire Extinguishants and their Uses

The methods of extinguishing fires have led to the development of several types
of extinguishants to cater for different types of fire. These methods include:

Cooling the fuel


Excluding the oxygen
Separating the fuel from the oxygen

The materials, used as general domestic and commercial extinguishants, differ


from those used in aircraft Fire Protection systems and, while the aircraft systems
are discussed in other Modules of this course, consideration is given here only to
the extinguishants and extinguishers which conform to the EN3 Standard fire
extinguisher code. The materials used in these extinguishers are:

Water (Water/Gas)
Aqueous Film-Forming Foam (AFFF)
Carbon Dioxide (CO2)
Dry Powder

Applying the incorrect extinguishant to a fire can do more harm than good and
may, actually, be dangerous. It is, therefore, important that extinguishers are well
marked for quick identification in an emergency. It is also vital that all personnel
are aware of the markings, which appear on extinguishers, so that the correct one
is chosen to deal with a specific fire.

Table 2 shows how the EN3 Standard fire extinguisher code has replaced the
older Standard, whereby the extinguisher containers were colour-coded all over
to signify their contents. The EN3 Standard has the bodies of every fire
extinguisher coloured red all over, with an identifying band of colour, separated by
white lines, identifying the extinguishant contained in the extinguisher.

Table 2
FIRE Extinguisher IDENTIFICATION and Uses
EN3 Standard Extinguishers (All-red Container)
Extinguishant Band Colour Types of Fire
Water Red Solids only, but NOT Electrical NOR
(Water/Gas) Flammable Liquids
Aqueous Film-Forming Foam Cream Oil, Fats, Paint, Petrol, and Solids,
(AFFF) but NOT safe on Electrical fires
Carbon Dioxide Black Gases, Electrical, Flammable Liquids
(CO2) and Solids but NOT Burning Metals
Dry Powder Blue Burning Metals, Flammable Liquids,
and Electrical (<1000 V, >1 m) fires

370280148.doc Issued December 2002 Page 3


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

From Table 2 it can be seen that Water or Water/Gas extinguishers are ONLY to
be used on fires involving burning solids (Class A fires). Water could also cause
liquid fires to spread and, obviously, using water on electrical equipment could
have lethal results, so these extinguishers must NOT be used on Class B NOR
on Class C fires. Water should, also, NOT be used on burning metal (Class D)
fires, as the oxygen, in the water, will cause the fires to burn more fiercely and its
use could lead to violent explosions.

Aqueous Film-Forming Foam (AFFF) is best suited for Class B fires, due to its
smothering and cooling action and to the fact that its finer particles will not cause
the fire to spread. AFFF extinguishers can also be used on Class A fires (though
its cooling action is not as effective as the water extinguishers), but, because
Foam does contain water, AFFF extinguishers are considered to be NOT safe on
electrical fires where high voltages are encountered.

Carbon Dioxide (CO2) is the universal fire extinguisher and, being non-corrosive,
non-conductive, and leaving no residue, it is suitable for almost all types of fire.
CO2 extinguishers must NOT, however, be used on Class D fires, as the
extinguishant reduces the temperature very quickly, which (in a similar way to the
use of water extinguishers) could cause serious explosions.

Due to the fact that CO2 gas tends to dissipate quickly, the extinguisher is
provided with a horn device, which helps to concentrate the CO 2 at the site of the
fire. This horn must NOT be held with bare hands, as the intense cold of the
released CO2 will freeze the skin to the horn, resulting in severe injury to the
hands. A rubber, insulated coating is provided on the discharge tube and the CO 2
must be directed towards the fire by grasping and manipulating the insulated
tube.

Dry Powder is another extinguishant which is suitable for most classes of fire,
and, in particular, those involving burning metals (aircraft wheel brake fires). It is,
however, limited in its use on electrical fires, as the powder particles are capable
of conducting high voltages (in excess of 1000 V) and, possibly, lesser voltages if
they are used at distances of less than 1 metre from electrical fires. Dry Powder
(in a similar way to Foam), leaves a messy residue after its use, which could
present a problem to electrical contacts and circuitry.

Note: It is possible that the older Standard Halon fire extinguishants (in green-
coloured containers) may be found at many indoor locations. Unfortunately, while
Halons (Halogenated Hydrocarbons) are extremely effective as extinguishants of
virtually every class of fire, it is felt that they contribute to the depletion of the
ozone layer surrounding Earth and, so, they are being phased out of use.

Buckets of dry sand may also be placed at the FIRE POINT in workshops (and
especially in hangars) as an additional aid to fire fighting.

Page 4 370280148.doc Issued December 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

2.2 First Aid

It has been previously discussed that, when working indoors, whether it is in an


office, a workshop or a hangar, there will be fixed points where fire-fighting
equipment is available. Similarly, there will be First Aid points where emergency
kits, eye washing equipment and call bells are installed and there will be trained
First Aid personnel to assist in the treatment of injuries. It is the responsibility of
every person at work to know:

The location of the First Aid Points


The methods of calling for help
The locations of alarm bells, and the siting of appropriate telephones which
may be used to summon help in an emergency
The identity of the trained First Aid personnel in their vicinity

In the event of an injury (however slight), it is important that the injured person, or
the attending First Aider, should complete an entry in the Accident Book, which is
usually kept near the First Aid Point.

2.3 Workshop and Hangar Safety

When working in a workshop or in any hangar, there are a number of safety


precautions that must be followed, if injury (or death) is to be avoided.

2.3.1 Machinery

A machine can be defined as an apparatus for applying power, having fixed and
moving parts, each having a definite function. In particular, machines embrace:

Operational Parts - performing the principal output function (Chucks or Bits)


Non-Operational Parts - conveying power or motion (Motor Drives).

The wide range of machinery, available in workshops and hangars, precludes


giving specific rules and regulations for each machine. The basic drilling, grinding
and milling types of machine, all require the use of eye protection, attachment of
guards, secure holding of work and, most importantly, correct training before
being operated.

Possible accidents from machinery, in general, include personnel:

Coming into contact with the machinery


Being trapped between machinery and material
Being struck by machinery or being entangled in its motion
Being struck by ejected parts or material
Receiving electric shocks from the machinery

370280148.doc Issued December 2002 Page 5


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

2.3.2 Electricity

The human body conducts electricity. Furthermore, electrical current, passing


through the body, disrupts the nervous system and causes burns at the entry and
exit points. The current, used in domestic 220-240 volt, 50Hz ac electricity, is
particularly dangerous because it affects nerves in such a way that a person,
holding a current-carrying conductor, is unable to release it. Table 2 shows some
typical harmful values and effects of both ac and dc electricity supplies.

Table 2
Harmful Values of Electricity
Voltage/Current Possible Outcome
50V ac or 100V dc May give rise to dangerous shocks
1 mA Harmless tingle
1 12 mA Painful, but can be released
12 20 mA Very painful, cannot be released
20 50 mA Paralysis of respiration
> 50 mA Heart stoppage

Since water also conducts electricity, great care must be taken to avoid handling
electrical equipment of all kinds when standing on a wet surface or when wearing
wet shoes. The water provides a path to earth and heightens the possibility of
electric shock. To ensure that equipment is safe, the minimum requirement is
through the use of three-core cable (which includes an earth lead) and, possibly,
a safety cut-out device.

In conjunction, more often than not, with ignorance or carelessness, electrical


hazards generally arise due to one or more of the following factors:

Inadequate or non-existent earthing


Worn or damaged wiring, insulation, plugs, sockets and other installations
Bad wiring systems and the misuse of good systems
Incorrect use of fuses
Inadequate inspection and maintenance of power tools and equipment

All electrical equipment must be regularly checked and tested for correct
operation and electrical safety. To show that this has been done, a dated label
should be attached, showing when the equipment was last tested and when the
next inspection is due.

Any new item of equipment must have a test label attached. The presence of a
test label does not, however, absolve the user from checking the equipment for
any external signs of damage, such as a frayed power cord (or missing safety
devices) before use.

In the event of a person witnessing another person receiving an electric shock,


the basic actions, to be followed by the witness, are:

Page 6 370280148.doc Issued December 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

Shout for help and ensure there is no danger of also becoming a victim
Switch off the electrical current or remove the victim from the supply by means
of insulated material
If the victim has ceased breathing, initiate resuscitation
Call for professional medical help
If the victim is suffering from burns, exclude air from wounds
Treat for shock by keeping the victim warm

The approved methods of artificial resuscitation must, by law, be displayed on


wall charts in workplaces.

2.3.3 Noise

Workshops, hangars and flight lines can be very noisy places of work, so it is
essential that ear defenders, or some other protection such as ear plugs, are
used at all times that noise is perceived to be a risk. Loss of hearing, leading to
deafness, can be the result of operating in a noisy environment without adequate
ear protection. Ear protection is optional where noise levels are less than 85 dB,
but is mandatory when greater than 90 dB.

2.3.4 High-Pressure Gases

Compressed gases are frequently used in the maintenance and servicing of


aircraft. The use of compressed gases requires a special set of safety measures.
The following rules apply for the use of compressed gases:

Cylinders of compressed gas must be handled in the same way as any high-
energy (and therefore potentially explosive) sources
Eye protection must always be worn when handling compressed gases
Never use a cylinder that cannot be positively identified
When storing or moving a cylinder, have the cap securely in place to protect
the valve stem
When large cylinders are moved, ensure that they are securely attached to
the correct trolley or vehicle
Use the appropriate regulator on each gas cylinder
Never direct high-pressure gases at a person
Do not use compressed gas or compressed air to blow away dust and dirt, as
the resulting flying particles are dangerous
Release compressed gas slowly. The rapid release of a compressed gas will
cause an unsecured gas hose to whip about and even build up a static
charge, which could ignite a combustible gas
Keep gas cylinders clean. Oil or grease on an oxygen cylinder can cause
spontaneous combustion and explosions

370280148.doc Issued December 2002 Page 7


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

2.3.5 Gas Bottle Identification

High-pressure gas cylinders contain various types of gas, the most common used
on commercial aircraft being nitrogen and oxygen. To ensure correct identification
of these containers, they are colour coded and the name of the gas is stencilled
on the side.

In the UK, gas containers use BS 381C as the standard to determine the correct
colour and shade for each gas type. Nitrogen bottles are painted grey on the
body with a black neck, whilst oxygen bottles are black with a white neck. Be
aware that bottles of US manufacture use an alternative system, the main
difference being oxygen bottles are painted green all over.

2.3.6 High-Pressure Gas Replenishing

When replenishing aircraft services such as tyres and hydraulic accumulators


with high-pressure gas, care must be taken to ensure that only the required
pressure enters the container. When full, a gas storage bottle can hold as much
as 200 bar (3000 psi) whilst an aircraft tyre pressure may only require 7 bar (100
psi).

To safely control the gas, two pressure regulating valves are used, one at the
storage bottle end and one at the delivery end of the system. If one valve fails the
other will prevent the receiving vessel from taking the full bottle pressure with the
consequence of an explosion.

For added safety the gas bottle valve opening key should be left in the valve
whilst decanting operations are completed. If problems occur then the high-
pressure bottle can be quickly isolated before the situation becomes dangerous.

The transfer of high-pressure gases from a large storage bottle to the aircraft
component is often called decanting and must be done at a very slow rate. If the
gas is decanted rapidly the temperature of the receiving component will increase
in accordance with the gas laws.

Again using the same gas laws the temperature of the gas in the container will
drop to ambient, and the pressure in that vessel will reduce. The component
pressure will now be incorrect and require the decanting process to be repeated.

Page 8 370280148.doc Issued December 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

In workshops, compressed air is, sometimes, produced by a compressor (which


is housed in a remote building), and fed, via galleries, to work stations. Care must
be taken to ensure that no damage occurs to the piping whilst in use.

If a concentrated stream of compressed air is blown across a cut in a persons


skin, then air can enter the blood stream and cause injury or death. For this
reason, air-dusting guns are restricted to about 2000 kPa (30 psi).

Aircraft tyres can require very high pressures and must be inflated inside a strong
cage. This cage would protect the personnel working on the wheels in the event
of a tyre or wheel bursting.

2.3.7 Oxygen Systems

Modern aircraft fly at altitudes where life support systems are needed. Even
though most of these aircraft are pressurised, emergency oxygen must be carried
in the event that the pressurisation system fails. Smaller aircraft can carry oxygen
in cylinders whilst the larger, civil aircraft have individual oxygen generator units.

These units are stowed in the overhead cargo bins, above the passenger seats,
and are known as the passenger service units or PSUs. A PSU produces oxygen,
by means of a chemical reaction, and is activated when its mask (which drops
from the overhead bin in an emergency) is pulled by a passenger.

Note: When PSUs reach their life expiry and have to be returned to their
manufacturer, it is vital that all precautions are followed to make the units safe
for transit. PSUs get very hot when working and have caused the destruction, due
to fire, of an aircraft, which was carrying these units as cargo.

The main oxygen systems are serviced from trolleys or vehicles that carry a
number of high-pressure bottles of oxygen, which can be at 140 bar (2000 psi) or
more. Some trolleys may also have a bottle of nitrogen, to allow the
replenishment of hydraulic accumulators and landing gears. The two types of
bottles must be separated, in order to prevent the accidental mixing of the gases.

It is extremely important that oxygen cylinders be treated with special care,


because, in addition to having all the dangers inherent with all other high-
pressure gases, oxygen always possesses the risk of combustion and explosion.

As previously stated, oxygen must never be allowed to come into contact with
petroleum products such as oil and grease, since oxygen causes these materials
to ignite spontaneously and to burn. Furthermore, an oil-soaked rag, or tools that
are oily or greasy (or badly oil-stained overalls), must never be used when
installing an adapter or a regulator on an oxygen cylinder.

370280148.doc Issued December 2002 Page 9


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

Due to the risk of fire and explosion, replenishing trolleys must never be parked
close to hydraulic oil replenishing rigs, or in any area where petroleum products
are likely to come into contact with the oxygen servicing equipment. Similarly only
specially approved thread lubricants can be used when assembling oxygen
components.

2.3.8 Aviation Oils and Fuels

Aviation oils, generally, are a fairly low-risk material when compared with the
more volatile, higher distillates of petroleum such as the aviation fuels - petrol
(gasoline) and paraffin (kerosene). Most lubricating oils are flammable, if enough
heat is generated but, when the materials are kept away from excessive heat
sources, they are (comparatively) quite benign.

Synthetic lubricating oils, methanol and some hydraulic oils may be harmful or
even toxic if their vapours are inhaled. Also, if they come into contact with the skin
or eyes, they can cause injury or blindness. Particular note should be taken of
any warnings of dangers to health that may be contained in the relevant
maintenance manuals and the recommended procedures for the handling of
these liquids should always be observed.

Oils and fuels also have an adverse effect on paintwork, adhesives and sealants
and, thus, may inhibit corrosion-prevention schemes. Care should, therefore, be
taken not to spill any of these liquids but, if a spillage should occur, it must be
cleaned up immediately.

Note: Sweeping up gasoline spillage with a dry broom can cause a build up of
static electricity, with the accompanying risk of explosion.

With gasoline and kerosene there is a much greater chance of fire, so more
thorough precautions are required. These start with the basic rules, such as not
wearing footwear with nails or studs (to prevent sparks), not carrying matches or
cigarette lighters and ensuring that ALL replenishing equipment is fully
serviceable.

Note: All references to refuelling, normally, also include the action of de-fuelling
and both are considered under the common term of fuelling.

During any fuelling operation, in a workshop, a hangar or on the flight line, the
relevant fire extinguishers must be in place.

Page 10 370280148.doc Issued December 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

2.3.9 Chemical and Physiological Hazards

Many chemical compounds, both liquid and solid, are used in aircraft
maintenance and these may need specific precautions. Any precautions can be
found in the relevant maintenance manuals and in the Control of Substances
Hazardous to Health (COSHH) leaflets applicable to those materials.

The range of adhesives used for repair and sealing during the maintenance of
aircraft is vast. A large number of these produce vapours which, generally, can be
dangerous in any enclosed space, both from the results of inhalation of narcotic
fumes and from the fire risk associated with those which give off volatile,
flammable, vapours.

Surface finishes present another area where the various types of material used
(etchants, celluloses, acrylics, enamels, polyurethanes etc.), dictate specific
precautions. The solvents used, before the actual painting and afterwards, need
safety precautions with regards to ventilation, reaction with other materials and,
most importantly, their possible corrosive, toxic, irritant and addictive effects on
personnel.

Some materials have a mildly radioactive property, although they emit little
ionising radiation in normal circumstances. These materials are sometimes
referred to as heavy metals and can be found in balance-weights as well as in
smoke detectors, luminescent EXIT signs and instruments.

This radiation differs from that used for non-destructive testing (NDT) procedures,
where high levels of radiation are employed, by specially trained personnel, and
which, therefore, require many safety precautions to avoid personal injury. The
safety precautions for NDT procedures will be found within the manuals
applicable to their employment.

2.3.10 Lifting and Shoring

Aircraft must often be raised from the hangar floor for weighing, maintenance or
repair. There are several methods of doing this, however, and the maintenance
manuals must be followed, during whichever method is used.

It is often necessary to lift only one wheel from the floor, to change a wheel or to
service a wheel assembly or brake unit. For this type of jacking, some
manufacturers have made provision on the undercarriage leg for the placement of
a short hydraulic jack. When using this method, never place the jack under the
brake housing or in any location that is not approved by the manufacturer.

370280148.doc Issued December 2002 Page 11


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

When jacking an aircraft asymmetrically, there is usually some movement by the


other legs. Care must be shown, when jacking a single leg, that the aircraft is
raised strictly in accordance with the maintenance manual.

Other places where a larger jack may be connected to the airframe might be:

Under the wings, at the main spar position


Under the nose
Under the tail assembly
On the side of the front fuselage (in place of the nose jack)

The location and operation of ALL jacks must be carried out both with great care
and with the correct number of personnel, who must be well briefed.

Most of the larger jacks have a screw-type, safety locking collar, to prevent the
jack collapsing in the event of a sudden leak. The jack operator must ensure that
these safety collars are gradually screwed down, as the aircraft is being raised,
so that they are very close to the jack body at all times.

As an additional precaution, especially if the aircraft is to be worked on for an


extended period, trestles or steadies can be installed under the wings and
fuselage to augment the jacks and also to provide an additional means of shoring
(supporting) the aircraft.

2.3.11 Slinging

It can be necessary, on occasions, to lift either the major components of an


aircraft, such as wing or tail assemblies or the complete aircraft (refer to Fig. 2).
For example, when recovering an aircraft from an overrun, it may be easier, and
safer, to lift the entire aircraft and place it onto a hard standing, than to try and
pull it out of soft ground, using a tug or similar vehicle.

When lifting either major components or an entire aircraft, the slings must be
produced or approved by the manufacturer of the aircraft. The manufacturers
slings ensure that the centre of gravity of the component, is always directly
beneath the lifting hook of the sling.

Page 12 370280148.doc Issued December 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

Lifting an Aircraft with Slings


Fig. 2

2.4 Flight-Line Safety

Many sources of accidents on the flight line are involved with propellers and rotor
blades. They are difficult to see when they are turning, and personnel (despite
being familiar with the hazards of propellers and rotors), sometimes become
distracted and forget about the danger. The main difference between these, and
other flight-line accidents, is that they are almost always fatal.

Most blades have high-visibility markings, to ensure that they can be seen when
they are turning. These markings vary from a yellow blade tip marking, to black
and white alternate stripes along the full blade length.

To reduce the risk of propeller and rotor blade strikes, it is best to follow strict
rules as to the correct way to approach and leave the vicinity of an aircraft or
helicopter whilst it is under power. For example (and allowing for the fact that
there are specific rules laid down for each aircraft), installing and removing
chocks should normally be done from the wing-tip direction. Boarding and leaving
a helicopter should always be done from the side.

When dealing with running jet engines there are similar dangers. These come not
only from the noise risk, which can result in deafness, but also from the risk of
intake suction, which has resulted in ramp personnel being sucked into the
engine and being killed. At the rear of the aircraft, there is the risk of jet blast,
which, at maximum thrust is quite capable of overturning a vehicle if it passes too
close behind the aircraft. (refer to Fig. 3). Piston-powered aircraft (depending on
their size) will have similar danger areas.

370280148.doc Issued December 2002 Page 13


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

Distance 0 10 20 30 40 50
(metres)

Typical Aircraft Danger Areas


Fig. 3

2.4.1 Towing and Taxying

If an aircraft requires moving and no pilot is available, then a tug and towing arm
must be used. This task will require a qualified tug driver, a supervisor, a brake
man and other personnel to keep a lookout. A qualified pilot always does the
taxiing of larger aircraft, although engineers sometimes taxi light aircraft.

Each aircraft and its operator will have laid down rules regarding the way in which
each aircraft will be towed. These rules will include the number of people needed,
the type of tug, the radio calls if the aircraft is on the manoeuvring area, the
maximum towing speed and many other details. These must always be followed if
accidents are to be avoided.

Aircraft, when moving, either under power or whilst being towed, are sources of
numerous risk areas. An airliner can be over 60 metres long and have a wing
span greater than 60 metres. This means that when manoeuvring in restricted
spaces, there is always the risk of part of the aircraft striking another object, due
to a phenomenon known as Swept Wing Growth (refer to Fig. 4).

It must be borne in mind that, when turning, the wing tips and tail of a large
aircraft can move considerable distances in the opposite direction to that of the
nose. This is why, whenever an aircraft is approaching its parking spot, there
must be personnel available to watch out for any potential conflicts.

Driving in the vicinity of a parked aircraft must always be done with care,
especially if the driver is alone or visibility from the cab of the vehicle is limited.

Page 14 370280148.doc Issued December 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

Tail Sweep Area


Wing Tip Sweep Area

Aircraft
Turning
To Left

Path of Wing Tip


Path of Tail

Swept Wing Growth


Fig. 4

2.4.2 Parking

When an aircraft has to be parked for a period of time, especially overnight and in
inclement weather conditions, there are a number of precautions that must be
observed:

A chock must be placed at the front and rear of a number of wheels,


depending on the aircraft type
The engine intakes and exhausts may need to be covered with special blanks
The control surfaces may have to be locked in place with integral control or
gust locks or, if these are not installed, external locks may be attached to all of
the surfaces that could be damaged in high winds
Other devices required could include blanks for the pitot tubes and static
vents.

370280148.doc Issued December 2002 Page 15


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

2.4.3 Marshalling

When marshalling an aircraft, it is essential that personnel are fully conversant


with all the marshalling signals (refer to Fig. 5). It is also useful to know extra
details such as:

The need for additional, lookout men on the wing tips or tail
The correct place to stand to enable the aircrafts crew to have sight of the
marshaller
The point at which the aircraft is required to stop.

Come Ahead Stop Emergency Stop

Right Turn Left Turn All Clear (OK)

Remove Chocks Insert Chocks Slow Down

Some Basic Marshalling Signals for Fixed-Wing Aircraft


Fig. 5

Page 16 370280148.doc Issued December 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

2.4.4 Fuelling

While the topic of fuelling is covered more fully in Module 11 and in the relevant
Chapter (28) of the Maintenance Manual, brief consideration of some of the
general safety precautions is given here.

The first, obvious precaution, is the identification of the type of fuel in the fuel
tanker (or bowser), ensuring it is of the type and grade required for the aircraft.
There have been many times when petrol-powered aircraft have been filled with
turbine fuel and, on occasions, the reverse has occurred.

The type and grade of fuel should always be stencilled or painted, adjacent to the
fuelling point, but it is wise if a responsible person is consulted before starting
fuelling. This is because there may be a requirement for some special fuel, or
simply that the aircraft is only to be part-filled, due to a weight limitation.

The fuel tanker must be parked as far as possible from the aircraft, limited by the
hose length, and parallel or facing away from it. This reduces the risk of fire
passing from the aircraft to the tanker or vice versa, and also allows a clear path
for the tanker to vacate the area quickly, should the need arise.

The fuel tanker, the fuelling hose, the aircraft and the ground must all be
electrically bonded together, to allow the static electricity (generated during the
fuel flow) to run to earth.

A safety zone of 6m (20 ft) should be established from the filling and venting
points of the aircraft and attendant fuelling equipment. This area should be free
from naked lights, smoking and the operation of electrical switches of any kind.

There can also be a risk from the operation of radio and radar equipment, so
these should also be switched off before fuelling commences.

Also, during the fuelling of aircraft, Auxiliary Power Units (APU) and Ground
Power Units, (GPU), must be made safe, by checking that their exhausts and
intakes are clear of any fuel vapours, and that GPUs, are located as far as
practical from the fuelling point(s).

NO switching of power from APUs or GPUs will be made during fuelling


procedures.

There are many precautions involved when defuelling, due to the tanks being left
empty of fuel, leaving potentially explosive vapours in its place.

ALL necessary safety precautions must be followed during aircraft fuelling


procedures.

370280148.doc Issued December 2002 Page 17


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

2.4.5 Weather Radar

The heating and radiation effects of weather radar can be hazardous to life.
Personnel should remain a safe distance from the radar if it is in operation. There
are published figures and charts in the maintenance manual of each aircraft,
showing the safe distances for personnel, depending on the power of the radar in
use.

As an example, the aerial in the nose of the aircraft should have an unobstructed
view of something like 30 metres, with the aerial tilted upwards. There should
also be a barrier erected about 3 metres or so from the nose of the aircraft, to
prevent personnel getting too close.

Finally, there should be no fuelling operations in progress during the testing of


weather radar.

Page 18 370280148.doc Issued December 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

3 WORKSHOP PRACTICES

Despite the enormous advances in the mechanisation and computerisation of the


engineering industry in general, there remains the requirement for a high degree
of hand skills on the part of technicians who are engaged in the day-to-day
maintenance of aircraft and their associated components.

While the majority of aerospace components are manufactured under stringent


standards, in factory (and laboratory) conditions, it is necessary to remove many
items of equipment for cleaning, inspection, overhaul and, if needed, repair
before they are, subsequently, re-installed in their appointed locations.

These actions may entail the use of many specialist tools and materials, which
are used while following written procedures, while it is quite possible that some,
comparatively simple, repairs may call upon such basic hand skills as the cutting,
filing, drilling, riveting and painting of metals or other materials.

No matter whether there are specialist or basic skills required, all will demand a
certain quality of the work practices (and of the work-force) involved.

3.1 Care of Tools

Engineers are responsible for the maintenance of their personal tools, whilst
other personnel, in designated Tool Stores, must care for all the different,
specialist tools for which they have the responsibility. It is also the responsibility of
engineers to ensure that any tools, or other items of equipment they use, are not
left in an aircraft or associated components.

The care required for different tools can vary. Ordinary hand tools may merely
require racking or locating within sturdy tool boxes, with careful, daily,
maintenance restricted to little more than a visual check.

Precision instruments however, require great care both in storage and in use.
They may need to be kept in special, soft-lined, boxes within other storage
facilities. Prior to use they should have a zero check or calibration. Some tools
require that they have a light coating of machine oil, to prevent the onset of
corrosion.

Each tool (whether it be a hammer or a micrometer), will require some special


care, to ensure its optimum performance for, without this care, even the most
expensive tools very quickly become second rate and useless.

370280148.doc Issued December 2002 Page 1


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

Page 2 370280148.doc Issued December 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

As an alternative to operating an internal Measurement and Calibration System,


an Approved Organisation or an Approved/Licensed Engineer may enter into a
sub-contracting arrangement to use an Appliance Calibration Service. This
arrangement does not absolve the contractors of the service from maintaining
standards as if they were carrying out the work themselves.

370280148.doc Issued December 2002 Page 3


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

In all instances, it is the responsibility of the user to be satisfied that the unbroken
traceability chain is in place. External organisations, which supply an external
Calibration Service, should be those holding accreditation of the National
Accreditation of Measurement and Sampling, (NAMAS).

3.3.2 Procedures

The definition of appliances requiring calibration are those items which are
necessary to perform measurements or tests of an aircraft, a system or a
component, to defined limits, as specified in the technical documentation of the
Type Certificate holder.

Procedures, controlling regular inspection, servicing and, where appropriate,


calibration of such items, are to indicate to the users that the item is within any
inspection time limit. These Next Inspection labels must clearly state when, and,
if necessary, where the next calibration is due.

There should be a programme that plans the periodic inspection, service or


calibration within the defined time limit, which ensures that the item remains in
calibration. It is common sense to stagger the calibration of items, so that the
largest number are available for use at all times. It is also important, that a
register of all items requiring calibration is held, so that cross-checking can be
simply carried out. Where a small number of particular items are held, then
contract loan of equipment is permitted.

The intervals at which calibration is required, can vary with the nature of the
equipment, the conditions under which it is used and the consequences of
incorrect results. The frequency will be in accordance with the manufacturer or
suppliers instructions, unless the organisation can show that a different interval is
warranted in a particular case. This would normally require a system of
continuous analysis of calibration results to be established, to support the
variation to the recommended calibration intervals.

Any appliance, the serviceability of which is in doubt, should be removed from


service and clearly labelled accordingly. The appliance must not be returned to
service unless the reason for its unserviceability has been eliminated and its
continued calibration re-validated. Action must be taken, if an item of equipment
is found, during re-calibration, to have a significant error. This must include re-
checking of measurements made prior to finding the fault.

The scope of the records maintained, are dependent upon the standards required
and the nature of the equipment. The record system can also provide a valuable
reference in case of dispute or warranty claims. These records can also indicate
drift and can help in reassessing calibration intervals.

Page 4 370280148.doc Issued December 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

Calibration records or certificates should, as a minimum, contain the following


information for each appliance calibrated:

Identification of equipment
Limits of permissible error
Standard used
Authority under which the document was issued
Results obtained
Any limitation of use of equipment
Uncertainty of measurement
Date when each calibration was conducted
Assigned calibration interval.

Where calibration services are provided by outside organisations, it is acceptable


that the accuracy of the equipment is attested by a release document in the name
of the Calibration Company.

Any measurement is affected, to some degree, by the environment in which it is


made. The equipment will need to be calibrated, transported and stored under
conditions compatible with the type of equipment, to ensure its accuracy is not
impaired.

To provide valid and repeatable test results, the facilities used for calibration must
have a controlled environment. It is necessary to control the temperature,
humidity, vibration, dust, cleanliness, electromagnetic interference, lighting and
other factors that may affect the standard of the results. If any of these
requirements cannot be met, then compensation corrections must be applied to
the calibration standard to ensure continued accuracy.

A measurement Checking Standard can be applied, at the work place, to check


the accuracy of an appliance and to ensure its continued correct functioning. The
Checking Standard will be robust and its accuracy will not match that of a full
calibration check, but it will give confidence between checks that the equipment is
functioning correctly.

The company Quality System has the responsibility of ensuring the continued
accuracy, not only of the items of equipment, but also of the actual testing
facilities.

370280148.doc Issued December 2002 Page 5


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

3.4 Use of Workshop Materials

Many of the wide variety of materials, used in workshops, require some form of
control in their handling. This control can involve:

Safety: relating to such topics as the toxicity, corrosiveness or other health


risks associated with the use of certain materials

Management: referring to the storage, use and correct handling of all


materials whether they are solid, liquid, or, in some instances, gaseous

Economy: involving such matters as to the using of the correct dosage or


proportions when mixing compounds, using only as much material as required
for a specific task and to the keeping in stock of only sufficient materials and
thus avoiding lifed items reaching their expiry dates before being used.

Abrasive papers, solder and brazing materials, wire wool, tyre powder, oil spill
powder and so on, all require control of issue and use, though they may not,
normally, require stringent safety precautions.

A huge range of liquids can be used in the workshop situation, some of which are
harmless and some of which are extremely toxic. It is vital that the work-force
make themselves aware of the risks involved when dealing with ANY materials,
and especially when working within enclosed areas.

Some materials are flammable and must, therefore, be stored outdoors. These
include oils, greases, some adhesives, sealing and glazing compounds in
addition to many paints, enamels and epoxy surface finishes, which are stored in
metal cabinets and, usually, located (in the Northern hemisphere) on the North
side of a workshop or hangar. This ensures that the cabinet remains in the shade
of the building and does not get exposed to the suns hot rays during the day. It is
also important that only the minimum amount of these materials is taken indoors
for the work which is being done.

When handling materials that give off fumes, it may be necessary to have the
area well ventilated and/or have the operator wearing a mask or some form of
remote breathing apparatus. The finished work may also give off fumes for some
time afterwards, so care must be taken to keep it ventilated if necessary.

Obviously all liquids must only be used for the purpose for which they are
designed and never mixed together, unless the two materials are designed to be
mixed, such as with two part epoxy adhesives and sealants.
Many liquids used in workshops and in the hangar have (as mentioned earlier) a
fixed life. This date is printed on the container and must be checked before use,
because many materials are unsafe if used beyond their expiry date.

Page 6 370280148.doc Issued December 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

The disposal of liquids is a critical operation, and must only be carried out in
accordance with company (and, often, national or international) regulations.

Liquids must never be disposed of by pouring them into spare or unidentified


containers and they must not be allowed to enter the domestic drains systems.

The working with, and the use of, high pressure gas containers and oxygen
systems, was adequately discussed in the Safety Precautions topic.

3.5 Standards of Workmanship

Whilst the standards of workmanship, during the hand-working of metals and


other materials, is controlled by the craftsperson, once machinery is used in the
manufacturing process, then the standards of finish and workmanship depend
upon the allowances set by the designer and on the type of machinery being
used.

With hand tools, there are standards of finish, but these depend upon the skill of
the craftsperson and, again, on the tools being used. For example, when filing
metal, different grades of files are used, to obtain a comparatively smooth surface
finish while other methods, such as abrasive papers, pastes and polishes, are
then used, to provide the final finish.

When sawing, the same procedures apply in that blades with finer teeth will give
a better finish to the sawn edges, which may then be further smoothed, using an
appropriate selection of files.

When drilling a hole, the conventional twist drill will only produce a finish of a
certain standard. If a finer finish, to the inside of the hole, is required, then a
reamer would be used, to smooth the material inside the hole, so that, if a tight
fitting pin is to be fitted through the hole, there will be better surface contact.

There are a variety of machines that can generate a smooth surface on a piece of
metal, the selection between them being decided by the quality of finish. A lathe
can produce an exceptionally smooth surface on a bar or some other rotated
shape. If a large area is required to have a smooth finish, then perhaps, after
initial casting or forging, the choice may be of employing either a grinding
machine or a milling machine, to .provide the desired result.

In summary, the quality of the finished article is dependent both on the skill of the
craftsperson and the equipment available to complete the task. It does not matter
whether the tools in use are files and emery cloth or an expensive milling
machine; the standard of workmanship of the craftsperson can make a great deal
of difference to the finished article.

370280148.doc Issued December 2002 Page 7


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

PAGE
INTENTIONALLY
BLANK
.

Page 8 370280148.doc Issued December 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

4 TOOLS

Servicing of an aircraft, requires the dismantling, cleaning, examination,


adjustment and re-assembly of the parts in accordance with the maintenance
schedule. Further aspects of the work may require the manufacture of simple
components from metal or other materials, the drilling and tapping of holes,
removal of burrs and other operations. A reasonable degree of skill, in the use of
hand tools is, therefore, to be expected from all trades-persons. This skill can
only be obtained by practice, but it may be stated, that the more efficient the tool,
then the better will be the finished work.

4.1 Common Hand Tools

The best results are always obtained by using the correct tool for the task. Care
and maintenance of all tools is very important, since damaged or inefficient tools
can lead to injury of the user or damage to the components. A range of common
hand tools is considered in this part of the course.

4.1.1 Engineers Rule

An engineers rule (refer to Fig. 1) is made from high-carbon steel and is


graduated in Imperial and Metric units. Rules are classified by the length and
width of their graduated portion, must be kept free from rust and should not be
subjected to rough usage. The most common engineers rule has a length of
300mm (1ft) but rules can be obtained in lengths of up to 1,800mm (6ft).

The increment graduation marks are etched into the rule surface providing a
grooved recess. These grooves enable dividers to be set to a greater accuracy,
as the divider points can be felt to drop in to the recess.

Metric Scale

1 2 3 4 5 6 7 8 9 10 11 24 25 26 27 28 29 30
1 2 3 4 10 11 12

Imperial Scale
Edge View

Grooves

Engineers Rule
Fig. 1

370280148.doc Issued December 2002 Page 1


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

Page 2 370280148.doc Issued December 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

4.1.4 Fitters Square

The fitters square is used for setting out lines at right angles to an edge or
surface, and for checking right angular work for truth. Squares are made, to very
fine limits, of high-carbon steel and are classified by the length of the blade.

The blade and the stock have their opposing edges ground truly parallel with the
two limbs set at exactly 90 to each other.

To preserve its accuracy it is essential that it is handled carefully at all times and,
when not in use, kept in a protective case or box.

When testing a square for accuracy, it may be checked for truth against an
accurately machined right angular test piece such as a V block or master
square. If this is not possible, a test may be carried out (refer to Fig. 3) as follows:

Place the stock against the true edge of a flat surface and scribing a line on
the surface, using the outside edge of the blade
Turn the square over and check the outside edge of the blade against the
previously scribed line.

If the square is accurate, the blade edge and the scribed line will be in line. In a
similar manner, the inside edge of the blade can be tested.

True Edge

Error

Testing a Square
Fig. 3

370280148.doc Issued December 2002 Page 3


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

4.1.5 Combination Set

The Combination Set (refer to Fig. 4), consists of a graduated steel rule, which
has a machined groove running along the centre of its entire length. The rule can
be slid into three different heads and secured, by a locking screw device, so that
the combination of rule and head will enable certain tasks to be accomplished.

The Centre Head is used, with the rule, to locate the centre line of bars or round
tubes.

The Square Head has one working surface at 90 and another at 45 to the
locked rule. This allows the tool to be used, either in a similar manner to the
Fitters Square (to check the squareness of work), or it may be used for the
marking out of mitre joints and bevels.

A spirit level and scriber are, sometimes, accommodated in the base of the
Square Head, to permit a check to be done on the horizontal or vertical accuracy
of workpieces.

The Protractor Head also has a spirit level, which rotates with the head, and
allows the head to be used, singly, as a clinometer or, in conjunction with the rule,
it may be used to mark out and check angles on workpieces.
Scriber

Spirit Level
Centre Head
Square Head

Groove

Protractor Head

Combination Set
Fig. 4

Page 4 370280148.doc Issued December 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

4.1.6 Surface Plates and Tables

Surface plates (and surface tables which are larger), while not actually being
classed as marking out or measuring tools, are simply blocks of grey cast iron
with finely machined faces which can be used as a standard of flatness. They
may also be used to provide a true surface, from which marking out, measuring
and testing can be done.

Surface plates are usually mounted on a bench and, normally, only have three
supports, or feet, to ensure steadiness, if the surface of the bench were to be
slightly uneven.

Surface tables are free standing, on the workshop floor, and their sheer weight
provides the required steadiness.

The standard of the surface finish varies. The better grades are scraped and the
cheaper ones are merely planed. The accuracy of a planed table depends upon
the accuracy of the machine producing it.

Surfaces of grade A standard would only be used in Standards Rooms, grade B


surfaces are for inspection work while grade C surface plates and tables would
be found in typical workshops.

Surface plates and tables can be used to test for flatness, providing the standards
required are not too high. The surface of the plate is lightly smeared with a
mixture of engineers blue and a few drops of oil. The piece to be tested has to be
rubbed lightly on to the surface plate and any high spots will show up as blue
spots on the test piece. These spots will be filed or scraped until the whole
surface shows blue.

After use, a light film of oil should be applied to the working surface of the surface
plates and tables. They should, then, be protected with a wooden cover, to
prevent the onset of corrosion.

4.1.7 V Blocks

V Blocks are accurately machined, six-sided, rectangular blocks (generally made


of cast iron), which may be used, on surface plates and tables, to hold a round
bar, which can then be marked in a variety of ways, to give centres and lines
parallel to its side. V blocks are classified by the maximum diameter of the work,
which they can hold.

All opposite sides of the blocks are parallel and all adjacent faces are square to
each other. A 90 groove (in the shape of a V) is machined in two (longer)
opposite faces, but the grooves are cut at different depths, to cater for bars of
different diameters.

370280148.doc Issued December 2002 Page 5


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

The V-cut grooves have a small, square-cut, clearance groove in the bottom of
the V. This ensures that any oil, or dirt runs off the sides of the V and does not
clog the bottom of the V, causing an imperfect seating of any bar which were to
be placed in the blocks.

V blocks are made in (identified) matching pairs, which must always be used
together, so that a block of one pair should not be used with one of another pair.

Some V blocks also have grooves machined along the other two longer, parallel,
sides, to locate specially designed clamps, which may be used to securely hold
work while it is being accurately marked out or drilled.

4.1.8 Surface Gauge (Scribing Block)

A Surface Gauge, or Scribing Block (refer to Fig. 5), is another marking out tool,
used, on a surface plate or table, in conjunction with a scriber (and, occasionally,
with V blocks), for the marking of lines, which are parallel to a true surface.

The scriber is clamped to a spindle, which can be accurately pivoted, by means


of a fine adjustment screw, on the heavy base. The base, which is generally
made from cast iron (or hardened steel) is machined to be as flat as the surface
plate on which it slides, but it is also grooved (in a similar manner to the V block)
so that it can be used on round stock when required.

Two friction-fit pins, in the base, may be pushed down, to assist in drawing lines
parallel to a true edge.

V Blocks

Scribing Block

Surface Plate

Scribing Block with V Blocks and Surface Plate


Fig. 5

Page 6 370280148.doc Issued December 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

4.1.9 Dividers

Dividers are used to set out distances and to scribe arcs and circles. The legs are
made of high-carbon steel, the spring made of spring steel and the adjusting
mechanism of mild steel.

Dividers are classified by the length of their legs. The points should be kept sharp
and of equal length by stoning only the outside of the legs. If grinding is used to
sharpen the points, it must be done very carefully, as the temper of the points can
be drawn, leaving them soft.

The points of dividers should be protected, when not in use, in a similar manner
to those of scribers and such tools.

4.1.10 Callipers

Callipers (refer to Fig. 6) are a type of measuring device, typically used to


measure diameters and distances or for comparing sizes. The three basic types
of calliper are:

Outside Callipers: Used to measure the outside diameter of an object and


have legs that point inwards
Inside Callipers: Used to measure the inside of a hole and have legs that point
outwards
Odd-Leg Callipers (Hermaphrodite or Jenny Callipers): This tool is really half
callipers and half dividers. It may be used for scribing arcs on metal surfaces
from an edge, for scribing lines parallel to an edge or surface, (provided
accuracy is not of great importance), and for finding the centre of a round bar.

Outside Inside Oddleg

Callipers
Fig. 6

370280148.doc Issued December 2002 Page 7


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

4.1.11 Hammers

Hammers (refer to Fig. 7) are classified by their weight and type of head. Steel
heads are forged and manufactured from high-carbon steel. Most shafts are
made from straight-grained Ash or Hickory and are secured to the head by
wedging.

Ball Pein Straight Pein Cross Pein


Hide/Copper
Face

Hide Face
Rubber Head
Plastic Face

Types of Hammers
Fig. 7

As can be seen from Fig. 7, the main types of engineering hammers are the:

Ball Pein: The flat surface is used for most general-purpose work whilst the
ball pein is used primarily for riveting-type operations
Straight Pein: Used for general work, the narrow, straight pein being
particularly suitable for use where access to the work is limited

Page 8 370280148.doc Issued December 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

Cross Pein: As for the straight pein, but the axis of the pein is at 90 to that of
the shaft
Hide/Copper Face: The rawhide facing enables heavy blows to be delivered
without damaging the surface of the work, while the copper face may be used
for heavier types of work than hide faced hammers
Rubber Head and Plastic Face: More modern versions of the Hide Face
hammer. Can often have one of each type of face on each end of the head
Claw Hammer (not shown): More commonly used for woodworking. The face
is used for hammering nails whilst the claw is used for removing nails
Body Hammer (not shown): Little used in aircraft work, as they are primarily
used to remove dents and blemishes from sheet metal. They are also known
as planishing hammers.

The weight of hammer required can be found with experience. Before use, it must
be ensured that the head is secure on the shaft. The shaft should be gripped
close to the end opposite the head, as proper control is not possible if it is held
close to the head.

4.1.12 Punches

Although punches are not pounding tools, they do allow the force from a
hammer blow to be concentrated in the immediate area of the punch tip. This in
turn means that the pressure at the end of the punch is increased compared to a
hammer blow without a punch.

Over a period of time, the hammered shank end of a punch, tends to deform into
the shape of a mushroom. To reduce the chance of a metal chip flying off and
causing injury, during punching operations, the deformation should be removed
and the shank end returned to its original shape by the use of a bench grinder.

Eye or face protection should always be used when using punches of any type.

The types of punches, more commonly found in an engineers toolkit, include:

Centre Punches
Pin Punches
Hollow Punches
Drifts

The first three punches are, usually, constructed from hexagonal (or knurled,
round) rods of tempered, cast steel with a length of approximately 127 mm (5 in),
a gripping diameter of approximately 3.175 mm (0.125 in) and a smaller, driving
end of the appropriate size.

370280148.doc Issued December 2002 Page 9


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

Centre Punches are relatively sharp-pointed tools, used to make an indentation in


metal. The indentation aids in locating the centre of a hole and for starting a drill
bit when drilling the hole. The points may be ground at angles between 60 to
90, depending on the hardness of the metal on which the punch is being used.
The softer the metal, then the larger will be the angle of the punchs point.

When using a centre punch, it must be struck hard enough to give an indentation
large enough for a drill bit to start, but not so hard as to distort the metal.

Another form of Centre Punch is the Dot or Prick Punch (also Pricker), which
has a finer point and is used to make indentations along a drawn line when the
line is, otherwise, difficult to see. The indentations may also be used, when
sawing down to a line, as witness points, to show that the cutting is accurate.

Centre punches should not be used to drive out pins or rivets from their holes.

Pin Punches, as their name implies, are the tools to be used for the removal of
pins and rivets from their respective holes. The driving end of a Pin Punch is cut
flat, and its diameter ground to match that of the pin or rivet which is being driven
from its hole. Pin Punches may be found with parallel or tapered driving ends.

Hollow Punches are used to punch out bolt (or stud) holes in soft, thin sheets,
such as shimming or gasket materials, which are difficult to cut with drills. The
material being cut, should be supported by a wooden block, to avoid damaging
the cutting end of the Hollow Punch.

Drifts may be fashioned from aluminium alloy, copper or steel bars (or tubes), and
are used for driving out bearings, bushes or shafts from their respective cages or
housings.

Only steel drifts should be used on bearings, due to the possibility of small metal
chips, from the softer metals, breaking off and fouling the bearing assemblies.

4.1.13 Metal-Cutting Chisels

Metal-cutting chisels (also called Cold Chisels) are used in conjunction with steel
hammers. Chisels are forged, usually using short lengths of hexagonal-sectioned,
high-carbon steel bars, with the cutting edge hardened and tempered.

To prevent flying particles when hammering, the striking end is not hardened and
is, therefore, comparatively softer. Periodically, the burr, that forms at the striking
end of the chisel, should (in a similar manner to punches), be removed by filing or
grinding.

Alternatively, the chisels may be made of nickel-alloy steel, specially heat-treated,


to produce a long-lasting cutting edge.

Page 10 370280148.doc Issued December 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

Chisels are classified by their shape, overall length, cross-section of shank and
width of cut. There are four principal shapes of chisels (refer to Fig. 8), in general
use. They are the:

Flat
Cross-Cut
Diamond-Point
Half-Round.

Flat chisels are used for general chipping work, such as parting sheet metal or
cutting flat surfaces, preparatory to filing. The cutting edge is formed slightly
convex.

Cross-Cut (or Cape) chisels are used to cut narrow, flat-bottomed, grooves, such
as keyways in shafts or where it is not practical to use a flat chisel. These chisels
are also used to remove the heads of round-headed rivets during repairs.

Diamond-Point chisels are particularly useful for cutting in corners, cutting small
oil grooves and for rectifying an incorrect start when drilling.

Half-Round (and may, also, be called Round) chisels are general-purpose,


grooving chisels, which are suitable for cutting half-round, bottomed, grooves.
They are also suitable for rectifying an incorrect start when drilling.

Flat Cross-Cut Diamond-Point Half-Round

Chisel Types
Fig. 8

When selecting a chisel for a specific task, consideration must be given both to
the nature of the work and to the material that is to be cut. The nature of the work
governs the choice of shape, whilst the angle formed by the cutting edge is
influenced by the hardness of the metal.

370280148.doc Issued December 2002 Page 11


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

In general, it may be assumed that the softer the metal the more acute should be
the cutting angle. Table 5 shows some suggested cutting angles for use on typical
metals, found in aircraft engineering workshops.

Table 1
Suggested Chisel Cutting Angles
Hard Steels 70
Mild Steels 60
Soft Metals 40

High-carbon, steel chisels, should be sharpened by grinding on an abrasive


wheel, but nickel-alloy, steel chisels are sharpened by filing. The cutting edge of
the chisel must be kept cool, during grinding, by frequent immersion in water,
which will prevent the temper being drawn from the metal.

4.1.14 Bench Vice

The bench vice (refer to Fig. 9) is used to firmly grip the material or item upon
which work is being done in a workshop. The body of the vice is provided with
detachable steel jaws. The screw is made with a square or with a buttress thread.

Most types of bench vice have a quick-release mechanism, operated by a small


lever. The jaws can then be slid either open or closed until the correct position is
reached. The lever disengages the half nut from the thread to permit the sliding
action and it is driven back into engagement by a strong spring. Bench vices are
classified by the length of their jaws.

The height of the top of the vice above the ground is important, and should
ideally, be level with the technicians elbow when standing adjacent to the vice.
With the vice at the correct height, work will be less tiring and correct control of
the tools, such as files and saws, will be achieved.

The vice must be secured firmly to the bench (with occasional checks of the
holding-down nuts), and the screw should be kept clean and lubricated. The jaws
must not be over-tightened as the mechanism may be damaged or the workpiece
become distorted.

To protect soft materials from the hardened, serrated, vice jaws, aluminium vice
clamps (or clams) can be positioned over the jaws. Other, special holding
devices, such as V blocks (made out of wood to protect tubular items) can be
manufactured locally.

Page 12 370280148.doc Issued December 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

Bench Vice
Fig. 9

4.1.15 Hand Vice

A hand vice (refer to Fig. 10) is classified by its overall length and can be used
when splicing cables or holding small objects that are to be shaped or drilled. The
body and screw are made of mild steel, with a wing nut provided for the operation
of the hand vice. Small vice clamps can also be used with these vices when
working with soft material.

Hand Vice
Fig. 10

370280148.doc Issued December 2002 Page 13


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

4.1.16 Hacksaws

The hacksaw, is the most widely-used, metal-cutting, hand saw. Hacksaws are
used for parting off, or for cutting materials approximately to size. They are
designed primarily for cutting metal, but may be used on other materials. The saw
consists of a mild steel frame, with a suitable handle and a replaceable, serrated
blade, which is made from high-carbon or alloy steel.

Fine-toothed blades have 24 or 32 teeth per inch and are used for cutting thin
material. Coarser blades, with 14 or 18 teeth per inch are for thicker material. A
rule of thumb is that at least two teeth must be in contact, with the work being
cut, at all times (refer to Fig. 11).

Thicker Sections - Less Teeth per Inch

Thinner Sections - More Teeth per Inch

Hacksaw Teeth in Contact with Workpiece


Fig. 11

The blade mountings must be set in the most convenient position with the teeth
facing away from the handle. This allows the blade to cut on the more efficient,
forward stroke.

Hand pressure should be applied on this forward stroke and relieved on the
return stroke. The full length of the blade should be used for each stroke, if at all
possible. This action prolongs the life of the blade, lessens the chance of teeth
breaking away from the blade and reduces the chance of the saw jamming during
use.

Page 14 370280148.doc Issued December 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

Saw blades are given an alternate set, during manufacture, which results in the
cutting slot (the kerf) being wider than the blade thickness (refer to Fig. 12). This
prevents the blade from jamming, which may result in a bent or broken blade.

Teeth Set
Fig. 12

4.1.17 Sheet Metal Shears and Snips

Shears are another type of cutting tool used on aircraft sheet metal. Long,
straight cuts, across a piece of sheet metal, are made on a guillotine, which may
also be referred to as squaring shears.

The fabrication of smaller parts requires hand cutting, followed with further
trimming to the final dimensions. This can be achieved with different types of
shears, known as Tinmans Shears or Aviation Snips. They can vary in length
from 175 mm (7 in) up to 300 mm (12 in) and can be straight or curved cutting.

Straight shears (or snips) are primarily for cutting straight or wide radius curves
whilst the curved shears are dedicated solely to cutting curves.

Curved shears can be found in symmetrical form, which can be used to cut
curves in either direction, or they can be asymmetrical and dedicated to cutting
curves in one direction only. The handles of asymmetrically curved shears are
usually colour-coded (red and green), to indicate the intended cutting direction.
Left-cutting shears are coloured red while right-cutting shears are coloured
green).

Unlike hacksaws (and files), shears simply part the metal without removing any
material. This can, however, cause tiny fractures to occur along the severed lines
and so, for this reason, cuts should be made approximately 0.8 mm (0.03 in) from
the marking out line and the metal then filed down to the line.

370280148.doc Issued December 2002 Page 15


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

4.1.18 Files

Files are cutting tools for removing metal from a surface and are made of high-
carbon steel. The blade is hardened, whilst the tang (to which, a handle must
always be attached, for safety reasons, before the file is used), is left in a softer,
tougher condition and is, therefore, less brittle. Hand files are classified by their:

Length
Shape
Cross-Section
Cut
Grade.

The length of a file is measured from the shoulder to the tip of the blade. Files are
available, for special work, in lengths from 75 mm (3 in) to 350 mm (14 in). The
most common sizes are 150 mm (6 in), 200 mm (8 in) and 250 mm (10 in).

Files are available in a variety of shapes (refer to Fig. 13), and the most common
shapes are those which are:

Parallel
Tapered
Bellied.

Tip Shoulder

Parallel

Length Tang

Tapered

Bellied

Three Most Common Shapes of Files


Fig. 13

Page 16 370280148.doc Issued December 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

The various shapes and the cross-sections of files allow them to be used on a
wide range of tasks. The standard file cross-sections (refer to Fig. 14) are:

Hand
Round
Half-Round
Square
Three-Square.

Hand Round Half-Round Square Three-Square

File Cross-Sections
Fig. 14

The Hand is the most commonly used section for general filing; and the blade is
usually parallel in shape. One edge may be without teeth, to permit safe working
against a finished surface. Such a file is called a Hand Safe Edge (HSE) file.

The Round section is used in association with bellied, parallel and tapered blade
shapes, with the bellied being the one most commonly used. These files are
suitable for filing small radii.

Half-Round files are mostly associated with a bellied-shaped blades. Such files
are suitable for use on work of irregular shape or for filing large internal radii.

Square files may be bellied, tapered or parallel in shape. They are used for
internal work.

Three-Square (or Triangular) files are, usually, of the bellied shape. They are
particularly useful for filing internal corners.

370280148.doc Issued December 2002 Page 17


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

The Cut of a file refers to the arrangement of the cutting teeth, on the blade of
the file. The pattern, in which the teeth are cut, will depend upon the type of
material to be filed. The common cuts of files (refer to Fig. 15) are the:

Single Cut
Double Cut
Dreadnought
Rasp.

Single Cut Double Cut Dreadnought Rasp

File Cuts
Fig. 15
The Single Cut file has its teeth cut parallel, in a single direction and (for general
engineering), usually, at an angle of approximately 60 to the main axis of the
blade. This type of cut is relatively open and the teeth do not clog easily.

Sometimes referred to as Floats, single cut Hand files are, chiefly, used for filing
hard metals. Round files and the curved surface of Half-Round files are usually
single cut.

The Double Cut file also has one set of teeth cut at an angle of 60 to the centre
line of the file, with another, crossing set, cut at angle of approximately 75. This
is the most widely used type of file for general purposes.

The cut of the Dreadnoughts teeth, make this file especially suitable for heavy
cutting on broad, soft metal surfaces. Its use is generally restricted to the larger
sizes of flat files.

The teeth of the Rasp are cut with a punch, while the metal is hot, at the time of
manufacture. This type of cut is used for filing very soft materials such as wood
and leather.

Manufacturers will cut files to cater for a wide range of specialised materials, such
as encountered when working with aluminium and other non-ferrous alloys.

Page 18 370280148.doc Issued December 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

The Grade of a file refers to the depth and spacing (number of teeth per inch) of
the cutting teeth in a similar manner to the size and spacing of the particles
employed on abrasive papers and wheels. The rate of cutting and the finish given
to the work is determined, to a large extent, by the grade of the file.

While there are several more grades of files, available from manufacturers, the
most common grades (or degrees of coarseness) of the single and double cut
files, found in a typical aerospace technicians toolkit, are the:

Bastard
Second-Cut
Smooth.

The Bastard is a comparatively coarse grade of file and, though the number of
teeth per inch varies with each manufacturer, the Bastard file has approximately
30 teeth per inch. It removes metal fairly quickly and is intended, primarily, for
roughing out, but may be used for the entire work, if the finish is not important.

The Second-Cut files are finer (40 teeth per inch) and, consequently, give a better
surface finish to the work, but are slower cutting.

Smooth files (50 to 60 teeth per inch) enable a good finish to be obtained, but
such files cut comparatively slowly. They should, therefore, be used for finishing
work only.

4.1.19 Filing Techniques

Good filing is not just a matter of removing surplus metal. The correct amount of
material, at each point on the surface of the workpiece, needs to be removed, so
that the dimensions and tolerances, set by the drawing, will be met.

Proficiency comes with practice. New files should, if possible, be first used on soft
metal. This achieves tempering of the cutting teeth and will contribute to a longer
life for the file.

Before starting work, it must be ensured that the workpiece is secure and
correctly placed, as both hands are required for filing tasks.

A file must never be used without a handle. The file will not be under full control
and the risk of puncturing the wrist or palm is very great.

Files must be handled carefully. File blades, being hard, are also brittle and will
break if dropped. After use, all files should be returned to their respective racks or
bandolier-type holdalls, to prevent them knocking together and being damaged.

The length and grade of file, appropriate to the shape (and material) of the
workpiece, and to the quality of the desired surface finish, must always be used.

370280148.doc Issued December 2002 Page 19


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

As mentioned previously, the height of the vice is important and platforms may be
constructed, to ensure that the elbows of shorter persons are level with the top of
the vice. Any platforms, so constructed, should ensure that a correct stance be
attained, by the work-person, in front of the vice.

It is recommended that the person stand, with feet apart and (depending on
whether the person is left- or right-handed), one foot advanced, in a manner
similar to a boxer (or a fencer) taking guard. The body weight should be taken on
the balls of the feet but, primarily, over the rearmost foot.

Again depending on the person, the handle of the file is gripped in the
appropriate hand, while the palm of the other hand is placed, flat on the back of
the file, near the tip, when the tip of the file is resting on the workpiece.

Using a rocking action, the body weight is transferred over the forward foot while
pushing the file forward (and, simultaneously, to the left or right) with the gripping
hand, and exerting equal downward pressure, on the file, with both hands.

The full length of the file should be used for each stroke (which should not be
rushed) and, at the completion of the stroke, the action is reversed, excepting that
the downward pressure is relieved on the backstroke, as the file does not cut in
the rearward direction.

Obviously, if attempting to file a flat surface, then it must be ensured that the file
is kept level during the filing action and that regular checks are made to verify the
accuracy of the dimensions.

During work (and particularly so with non-ferrous metals), the teeth of the file
gradually become clogged (pinned) with small particles. If these pinnings are
ignored they will cause scratches to the surface of the workpiece with subsequent
loss of surface finish. To this end, pinnings should be regularly removed by the
use of a file card (also called a scratch card) or wire brush.

Chalk, rubbed along the face of the file, before starting the finishing work, will
assist in minimising pinning.

Draw-filing, by grasping the file between the fingers and thumbs of both hands,
on either side of a workpiece, and rubbing back and forth on the surface, may be
used to rectify any hollows, which may appear on a filed surface, due to
incorrect filing action. It may also be used, in conjuction with chalk, applied as
previously described, to assist in creating a finer surface finish.

Page 20 370280148.doc Issued December 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

4.1.20 Hand Brace (Hand Drill)

Whenever it is necessary to cut accurate, circular holes in materials, then, where


possible, the material should be securely clamped and the holes cut, using fixed,
power-operated drilling machines. These machines are usually found in
workshops and bays, bolted down to the floor (or to benches) and will be
discussed in later topics. Where it is impractical to do the work with fixed
machines, then the drilling is done, using either portable power tools or hand-
operated drills. Portable, power-operated tools will also be discussed later.

The Hand Brace, or, as it is more usually called, the Hand Drill (refer to Fig. 16),
is, typically, only used to drill holes of up to 6.5 mm, ( in) diameter in thin and
comparatively soft materials. The device shown is similar to those most
commonly found in the toolkits of aircraft technicians, though the actual design
will depend upon each manufacturer.

Another hand-operated drill, the Breast Brace, being larger, is designed to hold
larger drills than the hand drill and is, normally, used (in workshops etc.) for
drilling holes between 6.5 mm and 12 mm ( and in).

The breast brace has one other advantage over the hand drill, in that two running
speeds can be selected, which will more closely match the correct speed,
required by the various sized twist drills being employed.

Hand Brace (Hand Drill)


Fig. 16

370280148.doc Issued December 2002 Page 21


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

4.1.21 Twist Drills

While the range of tools, designed to create holes in metals and other materials is
vast, the Morse-type (named after its inventor, an American engineer) of Twist
Drill (refer to Fig. 17) is the one most commonly used in aircraft (and in general)
engineering.

The shank is the part of the twist drill that is gripped and driven by the chuck of
the drilling machine and it is on the shank that the details of the type (grade) and
diameter of the drill can usually be found printed or engraved.

On drills up to 12.5 mm () diameter, the shank is parallel and placed into the
jaws of a self-centring chuck. On drills above 12.5 mm the shank is usually
tapered (to a Morse Taper) of 1:20. The tapered shank fits directly into a matching
tapered housing in the drilling machine spindle.

The tapered shank usually ends in a tang and this arrangement provides a more
positive drive, which is necessary to overcome the higher forces when drilling
with the larger diameter drills.
Land
Flute
Point

Body Shank

Twist Drill
Fig. 17
The helical flute (or fluting), formed in the drill body, provides a rake angle for the
cutting edges of the drill. The fluting also allows any lubricant to flow towards the
cutting edges and provides a path for the waste metal (swarf), to move clear.

The land of the drill actually touches the wall of the hole and steadies the drill
during rotation. Immediately behind the land, metal is removed from the body of
the drill, to reduce the friction during rotation.

Page 22 370280148.doc Issued December 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

In order that the drill will cut properly, the point must be ground to the correct
shape (refer to Fig. 18). The cutting, angle of 59 (118 inclusive), a clearance
angle of 12 and a web angle of 130, are typical for normal metal cutting, such
as aluminium alloys, steels, cast iron and copper. These can be changed to suit
the cutting of different materials such as harder metals, softer metals or plastics.

Web or Point
Angle
115-135
Inclusive

Cutting Clearance Angle


Angle 12-15
59
Cutting
Edges
Typical Twist Drill Point Angles
Fig. 18

It is essential that the drill point is central and that the cutting angles of 59 are
equal. An offset point or unequal cutting angles will cause an unbalanced rotation
that will, in turn, produce an oversized hole.

To achieve the desired cutting and clearance angles (and resulting web angles), a
drill grinding attachment may be found attached to a grinding wheel in a
workshop.

Hand grinding/sharpening of drills can be achieved (especially after practice), to


an acceptable standard for general work. For the high standard of hole, required
to receive rivets, in the pressurised skins of aircraft, it is common practice to
discard drills, which have become blunt and to replace them with new drills.

There are many different grades of metal, used in the manufacture of twist drills,
the most common being:

Carbon Steel
High Speed Steel
Cobalt Steel.

370280148.doc Issued December 2002 Page 23


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

Carbon Steel drills, in addition to iron and carbon, contain various amounts of
manganese, silicon, sulphur and phosphorus. The letters CS may be found on
the shanks of these drills.

High Speed Steel (HSS) drills, contain a comparatively high percentage of


tungsten (8%-12%) with a lesser percentage of chromium (5%) and smaller
amounts of vanadium and, possibly, molybdenum added to the carbon and iron in
this steel.

HSS drills retain their hardness at low red heat and can, thus, be used at much
higher speeds than carbon steel drills. This results in much less damage to the
cutting edges and, although HSS drills are more expensive than CS drills they
can, over a period of time, result in a greater economy in the purchase of drills.

Cobalt Steel drills, contain up to 12% cobalt, with as much as 20% tungsten, 4%
chromium, 1%-2% vanadium and traces of molybdenum combined with 0.8%
carbon. These drills are normally used on metals such as stainless steels,
titanium and other very hard metals.

Being extremely hard, Cobalt Steel drills are also quite brittle. Because of this, the
use of these drills can be very dangerous, and, so, strict observance of the
recommended cutting speeds is essential.

Drill diameter sizes are also usually marked upon the shank of the drill and can
be identified by the method used in their sizing. The most common methods of
identifying the diameter of twist drills are:

Metric
Fractions of an inch
The Number/Letter range.

In the Metric range, the smallest, commercially available, drill has a diameter size
of 0.35 mm. The full range proceeds in increments of 0.05 mm up to 5.0 mm,
and, for larger sizes, in increments of 0.1 mm.

The Fractional (Inch) range has a minimum size of 1/64 diameter, proceeding in
steps of 1/64 up to 15/8, and then in steps of 1/32 up to 3 diameter.

Table 6 shows an extract from the Number/Letter Range method of sizing drills.
This method utilises numbers from 80 to 1 and letters from A to Z. The smallest
size being the Number 80 (0.35 mm diameter) drill, and the decreasing number of
sizing indicating an increase in the drill diameter.

Page 24 370280148.doc Issued December 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

The letters supersede the numbers after number 1 (5.80 mm) is reached, with the
next largest drill diameter being labelled A (5.85 mm). The letters then move
through the alphabet to the drill diameter size Z (10.50 mm), which is the end of
the scale.

Table 2
Extract from the Number/Letter Range OF DRILL SIZES
Number or Standard Number or Standard Number or Standard
Letter Metric Size Letter Metric Size Letter Metric Size
80 0.35 4 5.30 S 8.85
79 0.38 3 5.40 T 9.10
78 0.40 2 5.60 U 9.35
77 0.45 1 5.80 V 9.55
76 0.50 A 5.85 W 9.80
75 0.52 B 6.05 X 10.10
74 0.58 C 6.15 Y 10.30
73 0.60 D 6.25 Z 10.50

The Metric sizes have virtually superseded the numbered and lettered ranges
and, usually, a metric size can be found as a replacement for an obsolete size.

If the drill is too small to have the size stamped on the shank, then either a drill
gauge or a micrometer should be used to establish its size correctly.

The use of a suitable lubricant when drilling is very important, not only does the
use of lubricant improve the quality of the hole, but it also assists in dissipating
the heat produced by drilling. This improves the cutting efficiency and prolongs
the life of the drill. Table 3 shows some of the recommended lubricants, which
may be employed when drilling metals.

Table 3
Recommended Lubricants for Metals
Material Lubricant
Mild Steel Soluble Oil
High-Carbon and Alloy Steels Kerosene or Turpentine
Aluminium Alloys Kerosene
Cast Iron and Brass Usually no Lubricant Required

For a twist drill to cut efficiently it must rotate at the correct speed, in a particular
metal, for a given diameter drill. Most hand drills (excepting Breast Braces) are
limited to one speed, which is a compromise on the ideal speed for the material
and for the drill size. The speed of most static drilling machines can be varied by
means of a gearbox or variable drive belt/pulley arrangement.

370280148.doc Issued December 2002 Page 25


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

When drilling small holes, up to 6.0 mm () diameter, the depth of the centre
punch mark will, usually, accommodate the non-cutting, chisel-like point of the
drill, keeping it on centre and guiding the drill until it is established in the metal.

When a hole larger than 6.0 mm diameter is to be drilled, the centre punch mark
is not large enough to accept the non-cutting point of the drill. In this instance it
will be necessary to employ the use of a pilot drill (refer to Fig. 19) to provide a
guide for the larger drill.

Firstly the centre of the hole is marked out on the metal and care must be taken
to accurately centre punch the metal.

A small drill (the pilot drill), whose diameter is slightly larger than the non-cutting
point of the finished size drill, is selected and a pilot hole is drilled in the metal
(ensuring that the correct lubricant, for the particular metal, is used).

The pilot drill is replaced by the finished size drill, which can, then (and again
using lubricant), be guided through the pilot hole to complete the hole to the
appropriate size.

Using a Pilot Drill


Fig. 19

Page 26 370280148.doc Issued December 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

4.1.22 Stop, and Press (Dimpling), Countersinking Tools

Two special tools, used during the riveting process, are the Stop countersinking
bit and the Press countersinking, or (as it is more commonly known), the
Dimpling tool. Both of these tools have evolved as a result of the need for flush
skins on high-performance aircraft.

In order to have the rivet heads flush with the surface, the skin must be prepared
by either cutting away a portion of the metal to match the taper of the rivet head,
or by indenting (by pressing) the edges of the hole to accept the rivet head.

If the top sheet of the metal, being joined, is thicker than the tapered portion of
the rivet head, then the material should be cut countersunk.

Whilst the standard countersink bit (or a twist drill, twice the diameter of the rivet
hole) can be used, in a hand or power drill, to form a countersunk hole, the lack of
accuracy and consistency means they are only useful for small jobs and certainly
they should not be used where pressurised skins are concerned.

Where a large number of holes need to be countersunk to a consistent depth,


then the Stop Countersink tool should be used (refer to Fig. 20). This tool can be
adjusted to cut an exact countersink repeatedly, regardless of the force applied to
the drill/tool combination.

The pilots can be changed, depending on the size of holes in the material, leaving
the remainder of the tool to be used for all jobs unchanged. The stop may be held
rigidly, during cutting, to prevent marking the surface.

Locknut Stop

Fibre Collar
Face

Pilot
Drill Chuck
Fitting Chip Opening

Stop Countersink Tool


Fig. 20

370280148.doc Issued December 2002 Page 27


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

Press countersinking or dimpling is done where the aircraft skin is too thin to
countersink, and without the attendant risk of enlarging the drilled hole. The
edges of the hole are formed, to accommodate the head of the rivet, by using a
set of dimpling dies, using either coin dimpling or radius dimpling methods.

Coin dimpling forces the sheets into the lower die, leaving a sharply defined and
parallel-sided hole. This process also allows a number of sheets to be stacked
together at the expense of a complex pair of tools and leaves a neat, clean
dimpled hole with smooth sides (refer to Fig. 21).

Radius dimpling uses a male die to drive the sheets into a female die. The sides
of the formed holes are not as smooth as the coin dimpling method, but this less-
precise operation is quicker and cheaper to achieve.

With harder materials, such as magnesium and certain aluminium alloys, a


process called hot dimpling is used. This method involves pre-heating the metal,
so that it forms more easily and is less likely to crack when shaping takes place.

Dimpled
Punch
Skin
Skin

After Rivet has


been Formed
Die

Dimpling Tool
Fig. 21

Page 28 370280148.doc Issued December 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

4.1.23 Reamers

Reamers are precision-ground tools, which are used to enlarge drilled holes to
accurate dimensions and provide a smooth internal finish to accommodate
precision-ground bolts and some special types of rivets. Reamers are
manufactured from high-carbon steel or alloy steel and are fluted to provide a
series of cutting edges.

They are available, either for use by hand, or for using with a suitable drilling
machine. Machine reamers can usually be identified by the Morse tapered shank,
which is inserted directly into the spindle of a drilling machine.

The use of machine reamers is, usually, the prerogative of specialist machinists
and not of line- or hangar-based aircraft engineers so that only the hand-operated
reamers will be discussed here.

Hand reamers are rotated, by means of the hand wrench, which locates on the
squared portion of the shank. They must always be rotated only in the cutting
direction, even when withdrawing from a hole. The cutting lubricants, used on
specific materials, are those which are used for drilling procedures.

Reamers are used for removing only small amounts of material, which, typically,
for hand reamers, is approximately 0.2 mm-0.3 mm (0.008 in-0.012 in), so holes
should be drilled with this fact in mind.

Reamers are supplied in protective sleeves, to protect the fine, vulnerable cutting
edges, which run along the body of the tool and, to preserve the sharp edges,
they should be kept in their sleeves when not in use.

The three most common types of hand-operated reamers are the:

Hand Parallel Reamer


Hand Expanding Reamer
Hand Taper Reamer.

Hand Parallel Reamers (refer to Fig. 22) are fixed-size, parallel-bodied reamers,
possessing either straight or spiral flutes. The straight fluted reamer can be
considered to be the general-purpose reamer, whilst the spiral fluted reamer is
used for reaming holes which have keyways or grooves as the spiral flutes
smoothly bridge the edges of the gap in the metal while the reamer rotates.

370280148.doc Issued December 2002 Page 29


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

Straight Fluted Reamer

Spiral Fluted Reamer

Hand Parallel Reamers


Fig. 22

Hand Expanding Reamers (refer to Fig. 23) are used where standard parallel
reamers of the required dimension are not available. This type of reamer has
separate, replaceable blades that slide, in tapering slots, and which are held in
position by a pair of circular nuts. The reamer blades can be adjusted to the
required cutting size by slackening one nut and tightening the other.

The shape of each blade is such that, at any point along the slot, its cutting edge
is always parallel to the axis of the reamer. The size range of each expanding
reamer is stamped on its shank. The actual size set during adjustment can be
checked using either a ring gauge or micrometer/calliper.

Hand Expanding Reamer


Fig. 23

Page 30 370280148.doc Issued December 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

Hand Taper Reamers (refer to Fig. 24), are used to produce a tapered hole for
the insertion of a standard taper pin. The two types of tapered reamers are the:

Metric: This type, and its corresponding taper pins, have a taper of 1:50. Its
size is etched, or stamped, on the shank, and refers to its smaller diameter

Imperial: The reamers and the taper pins, for which they are used, have a
taper of 1:48. The size of a reamer is indicated by numbers (which range from
0 to 10), or by a fractional designation. The size is etched or stamped on the
shank and refers to its larger diameter.

Hand Taper Reamer


Fig. 24
The difference between the Metric and Imperial tapers is very slight, but it is
sufficient to make the taper pins incompatible. When replacement taper pins are
required, particularly when both types are available, then great care must be
taken to ensure that pins of the correct taper, size and type are installed.

370280148.doc Issued December 2002 Page 31


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

4.1.24 Internal Screw Thread, Cutting Taps

Taps are used for the hand cutting of internal (female) screw threads of the
common types, up to a maximum diameter of approximately 25.4 mm (1.0 in).
They are short, threaded bars of hardened and tempered steel, which are fluted
to give cutting edges and the end of the shank is squared, to facilitate turning with
a wrench (refer to Fig. 25). Taps are normally made in sets of three, with the
exception of the BA thread tap sets, which have only two taps to a set. A tap set,
which all have the same maximum diameter, normally consists of a:

Taper Tap
Second Tap
Plug Tap

The Taper Tap is used to start the thread cutting process. It is tapered gradually
from the point for about two thirds of the threaded length, so that it can enter the
pre-drilled hole easily and assist in the correct alignment of the tap (which is very
important) before cutting commences. The last third of its length has fully formed
threads.

The Second (or Intermediate) Tap is used, following the taper tap, to deepen the
thread. This tap is tapered for the first two or three threads only and, where it is
possible for the tap to pass the whole length through a hole, it is capable of
cutting a fully formed thread. The Intermediate is the tap that is not available in
BA thread tapping sets.

The Plug (or Bottoming) Tap has no taper and its purpose is to finish the threads
in deep, through holes or to cut threads to the bottom of blind holes.

Before the thread can be cut, a hole must be drilled in the workpiece. This hole
must be of the correct size and the drill that is selected (the tapping drill), must
have the same diameter as the minor diameter of the thread needed to be cut.
The correct tapping drill size can be obtained from workshop charts and
reference books.

Unfortunately, because taps are glass hard they are also brittle and can, thus, be
easily broken if due care is not given to their use. It is imperative that the taps
location in the drilled hole be constantly confirmed and that its main axis is
maintained in proper alignment with the corresponding axis of the hole.

Adequate cutting fluid (as used in the drilling procedure) must be applied, and the
arms of the wrench should be of an appropriate length (not too long) so that the
possibility of the tap wobbling in the hole, or excessive turning force being applied
to the tap (and especially to the smaller diameter taps), is minimised.

If a tap jams, and snaps off in a hole, its removal can cause serious difficulties.

Page 32 370280148.doc Issued December 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

Plug Tap

Full Length
Threads
Second Tap

2-3 Thread Full


Taper Threads

Taper Tap

Gradual Full
Taper Threads Conventional Tap Set
Fig. 25

Following the drilling of the correct sized hole, the tapping procedure involves
ensuring that the workpiece is securely held (firmly attached to another
component or clamped in a vice) and that the taper tap is attached to the correct
sized wrench. Taps, incidentally, may have right or left hand threads.

Applying lubricant as required, the taper tap is inserted into the hole and its
correct alignment verified (by use, for example, of an Engineers square), before
it is rotated clockwise (for a right hand thread), slowly and gently, until the initial
threads are established.

Once the initial threads are established, the tap must not be rotated continuously,
otherwise the cuttings will not break off and the tap will, consequently, jam in the
hole and, if forced, it will shatter.

To this end, the tap, after each full turn, is rotated backwards, approximately to
of a turn, to break the cuttings off. The forward rotation is then continued, with
subsequent cutting breaks, until the full thread portion of the tap has cut sufficient
full threads in the hole.

After the preliminary cut, the process is repeated, using the second tap (if not a
BA thread), and, if required, repeated again using the plug tap. The thread, and
each end of the hole (where accessible), should be cleaned out if burrs or swarf
are present and, with blind holes, the swarf must be cleared out of the hole
regularly to prevent the tap binding at the bottom of the hole.

In the event of a tap breaking in a hole, it may be necessary to resort to specialist


procedures (spark erosion for example) for its removal without causing further,
and, possibly, expensive damage, to the component or workpiece.

370280148.doc Issued December 2002 Page 33


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

4.1.25 External Screw Thread, Cutting Dies

Dies are used for the hand cutting of external (male) threads on round rods or
bars of comparatively small diameters. While there are several designs of dies
(depending on the diameter of the thread being cut), consideration is given here
only to the split circular or button dies (refer to Fig. 26), which are, typically,
found in aircraft maintenance workshops and may be used, by aircraft
technicians, for the manufacture of studs and similar items.

Circular dies consist of an internally threaded (right or left handed) disc of


hardened and tempered steel, which is fluted to form several cutting edges. Dies
also need to be rotated (in a similar manner to the previously mentioned taps), in
order to cut threads but, unlike a tap and wrench, a die is rotated by the use of a
stock.

Die discs, within the smaller diameter ranges have a standard outside diameter,
which allows a range of dies, with different internal sizes, to be used with the
same, standard, stock. The discs are split, to allow for a degree of adjustment to
the depth of the thread being cut.

The manufacturers name, thread type, diameter and number of threads per
millimetre (or inch) are marked on the face of the die (Taps, incidentally, are
similarly marked on their shanks).

Split Die
Shoulder

Stock

Outer Securing and


Adjusting Screws

Centre Adjusting Screw

Circular Die and Stock


Fig. 26

Page 34 370280148.doc Issued December 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

Before external thread cutting is commenced, it is necessary to obtain a suitable


length of rod, the diameter of which is equal to the major diameter of the thread to
be cut. Care needs to be taken in this matter (and especially where closely sized
Imperial and Metric rods are available) because it is possible to create a thread
on slightly undersized or oversized rods.

The undersized rod would, of course, be a looser fit with the corresponding
female threaded item, which would not be acceptable, while the oversize rod may
cause damage to the other threaded device by being too tight a fit.

The die should be placed in the stock with the tapered threads (if any) away from
the shoulder and the split aligned with the centre adjusting screw. It is next
necessary to set the die to the maximum diameter, by slightly slackening the
outer adjusting screws and gently tightening the centre adjusting screw. This will
ensure that the first cut will be shallow. Failure to do this will invariably result in a
poor quality thread.

A shallow taper, or chamfer, must be ground or filed onto the end of the rod; to
assist in the location of the die before cutting commences and the rod should be
clamped firmly, and, preferably, vertically in the bench vice with the tapered end
uppermost.

Once more, adequate lubrication must be used throughout the procedure, again,
using the same lubricants as used for the drilling and tapping tasks.

Ensuring that the die is set to cut the maximum diameter, as described previously,
the die should be placed squarely onto the taper of the rod and, with steady
downward hand pressure, the die is carefully rotated (clockwise) to start the cut.

It must be ensured that the die remains square to the rod at all times during the
cutting, which is continued in a series of small arcs, reversing each time to sever
the cuttings, in a similar manner as is done when using the taps.

When enough thread has been cut, the die is removed and the thread checked,
using a finished nut. If the thread proves to be too tight, then, after backing off the
centre adjusting screw and (carefully) turning the outer adjusting screws inwards
another cut is made with the die.

The procedure is repeated as often as necessary until a satisfactory fit is


achieved between the two, mating, threaded items.

As the internal tapped thread is NOT adjustable, the internal thread should be cut
first. The external thread, which CAN be slightly adjusted, should always be cut
last to ensure the desired degree of fit between the respective threads.

370280148.doc Issued December 2002 Page 35


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

4.1.26 Screwdrivers

Despite the many shapes and sizes which may be met, it can be stated that
screwdrivers may be divided into two main groups, which, basically, are:

Blade Screwdrivers
Cross-Point Screwdrivers.

Blade (or Common) screwdrivers consist of a high carbon or an alloy steel blade,
mounted into a wooden or composite handle. The end of the blade is ground to
engage the diagonal slot in the head of the screw. If the blade is of high carbon
steel, it will be hardened and tempered.

Screwdrivers in this category are classified by type and by the length of blade,
which can be from approximately 35 mm (1.5 in) to 300 mm (12 in) long, although
special screwdrivers can be obtained with blade lengths of 500 mm (20 in).

Some variations may incorporate a reversible ratchet device in the handle while
others may also have an Archimedes drive (as in a Pump screwdriver)).

All of these features would form part of the classification of the screwdriver.

The correct engagement of the screwdriver blade in the slotted head of the screw
or bolt is most important (refer to Fig. 27). The most common faults can be seen
in the illustration. The end of the blade should never be ground to a sharp chisel
edge and a blade of the correct thickness and width should always be chosen.

Screwdrivers of the wrong size can cause serious damage to fasteners,


surrounding aircraft structure and to the persons using them.

Blade too Small Blade Correct Blade too Large

Correct Screwdriver Engagement


Fig. 27

Page 36 370280148.doc Issued December 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

Cross-Point Screwdrivers have been designed, by the several manufacturers of


the different types of screw heads (refer to Fig. 28).

These screw heads allow greater torque to be applied to the fasteners but, due to
the variations in design, it is vital that the correct screwdriver be used with each
type of screw head as they are not compatible.

The accurate fit of cross-point screwdrivers into the recess in the respective
screw head is essential if damage is to be prevented.

Reed and Price Phillips Posidrive Triwing

Various Types of Cross-Point Screwdrivers


Fig. 28

There is also a wide selection of other specialist screwdrivers, which have been
made to allow certain tasks to be accomplished. These can include:

Offset (or Cranked) Screwdrivers: which can reach screws with little clearance
above their heads (and which may, also, have a blade at one end and a cross-
point at the other)
Reversible Tip Screwdrivers: with hexagonal shanks, that allow the shank of
the screwdriver to be reversed in the handle to provide a different tip, with a
blade at one end and a cross-point at the other end of the hexagonal shank
Interchangeable Tip Screwdrivers: which have a selection of socket-like tips,
that can be interchanged to suit any particular type of screw head.

370280148.doc Issued December 2002 Page 37


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

4.1.27 Pliers

Pliers are classified by type and overall length and usually made from alloy steel,
with an insulated handle. They are designed for gripping, bending or moving
small items that cannot be easily handled with the fingers. Some of the many
types, that are available for a variety of purposes, include:

Side-Cutting Pliers: which are the general-purpose type, and are useful for the
installation and removal of split pins. They also have a facility for cutting wire

Round-Nosed Pliers: which are useful for putting small radius bends into wire
in addition to a variety of other tasks

Flat-Nosed Pliers: which, because the jaws are much thinner, may be used for
many small holding and bending tasks, that are not possible with the side-
cutting pliers

Needle-Nosed Pliers: which have finely pointed jaws and can be used in
electrical and electronic work, that involves holding small components and thin
wires. Needle-nosed pliers may, sometimes, have the jaws turned at right
angles to the handles, to allow the operator to see the work being held

Wire-Locking Pliers: which are used for the specific task of gripping wire,
during the wire-locking of components. Due to their integral Archimedes
screw, they are also able to spin and so twist two wires, so that a neat and
tight wire-locking is obtained

Circlip Pliers: which may be found in two, basic forms (Internal and External).
Both types have pins on the ends of the jaws, which are used to install and
remove circlips from around (and from within) components. The mechanisms
are designed so that, squeezing the handles together, either results in the jaw
pins coming together, (Internal), or spreading apart (External).

There are other groups of gripping tools that could, loosely be called pliers, but
they usually go under the names of grips or clamps. These include Mole-type
Grips: which can be locked, holding a component, freeing up the operators hand
for other work, Pipe Clamps, which can be used for gripping pipe unions, and
Slip-Joint (or Water Pump) Pliers that can have several, different gripping ranges,
due to their multi-pivot mechanisms.

Page 38 370280148.doc Issued December 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

4.1.28 Wire Snips (Nippers)

Wire Snips (which are also, often, called Nippers) can be found with straight or
diagonal jaws and are both very useful for cutting and stripping wire. They are
also useful for removing split pins.

Care must be used, when cutting with wire snips, as the cut-off pieces (locking
wire and split pin legs in particular) can fly off, causing injury or getting lost within
the aircraft structure or engine bays, which could lead to corrosion or to the
jamming of vital control systems.

4.1.29 Spanners, Sockets and Wrenches

The commonest spanners are those which are used on the standard hexagonal
heads of bolts, nuts, screws and similarly shaped fastening devices.

Other spanners are often referred to as special or non-standard spanners, and


are used on different types of screw thread fastenings. Some of these special
spanners have a limited application, whilst others are specifically produced for a
particular component, and will only be found in special toolkits applicable to that
component.

Most spanners are manufactured from case-hardened mild steel, hardened and
tempered high-carbon steel or alloy-steel, though there are some which are made
from copper alloys, where spark-resistant tools are required.

The size of a spanner, is either marked on the jaw face, or on the shank, in the
units of the type of thread system being used on the fastening device.

The units, shown on a particular spanner, however, relate to different parts of the
fastening devices (refer to Fig. 29), so a knowledge of the spanner sizing systems
is necessary. The two main sizing systems are those of the:

British Standard Institution (BS) and British Association (BA) Imperial system
American/Unified (Imperial) and the Metric system.

The British Standard system uses Imperial units (fractions of an inch etc.) and
embraces two of the three main thread systems, used in British engineering, one
of which is no longer used in aircraft engineering.

The sizing, on BS spanners, relates to the nominal diameter of the nut, bolt or
stud, upon which the spanner is to be used. For example, a spanner marked as
BS indicates that the spanner is used on a " diameter bolt (nut, stud etc.),
although the actual distance across the jaws of this spanner would be 0.820".

370280148.doc Issued December 2002 Page 39


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

Earlier BS spanners can be found with two figures stamped adjacent to each
other (e.g. 7/16 BSW 1/2 BSF). The BSW figure relates to the Whitworth thread
system, which is not used on aircraft, due to its tendency to loosen when
subjected to vibration. The BSF refers to the British Standard Fine thread but, to
avoid confusion, the older system has now been brought into line with the BS
system, so that a " BS (BSF) spanner can (for general engineering purposes)
also be used on a " Whitworth bolt/nut combination.

British Association (the third British thread system) sizes, also use Imperial
measurements, and, although they are in decimal fractions of an inch, they are
represented by a whole number (2BA, 4BA, 6BA and so on) which again relates
to the nominal diameter of the fastening device.

The American Fine and Unified thread systems, also use Imperial measurements.
The sizes, stamped on spanners, refer to the dimensions across the spanner
jaws (or across the flats of the hexagon of the fastening device). A spanner
marked " A/F, would be used on a bolt with an actual diameter of 5/16".

Metric spanners are marked with a number also denoting the width (millimetres)
across the flats, of the hexagon shaped fastener on which it is used.

BS and BA
(Imperial) Dimensions

American/Unified (Imperial)
and Metric Dimensions

Spanner Sizing Systems


Fig. 29

It is important that the correct procedure is followed to avoid incorrect tools being
used to install or remove a nut, bolt, stud or any other fastening device.

In some instances the correct tool size may be quoted in the maintenance
manual. This must be strictly followed.

Page 40 370280148.doc Issued December 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

There are so many tool catalogues, crammed with a bewildering range of tools
that it is impossible to include so many in these course notes. Some of the more
common spanners and wrenches (in addition to the previously-mentioned tools),
which are liable to be found in the average toolkit, of an aircraft maintenance
technician, include such general tools as:

Set (Open-Jaw) Spanners


Ring Spanners
Flare Nut Spanners.
Sockets
Allen Keys
Torque Wrenches.

The Set or Open-Jaw spanners are usually made in double-ended form, to


provide two available sizes in one tool.

The open jaws are set at an angle (usually 15) to the axis of the shank, which is
a useful feature, because (when replacing nuts and bolts in restricted spaces), by
turning the spanner over, the nut or bolt can be approached from a different
angle. They are not, however, totally satisfactory devices, as the jaws only bear
against two of the available six flats of the hexagon. There is always the tendency
for the jaws to spring open when force is applied to the spanner.

Ring spanners are preferred to set spanners as they give full enclosure of the
hexagonal head of the nut or bolt, each corner of which engages snugly within an
angle in the aperture of the spanner. This aperture is usually bi-hexagonal, to
facilitate the use of the spanner when angular movement is restricted.

Ring spanners are usually supplied in double-ended form, to fit nuts and bolts of
consecutive sizes. The ends are normally offset but straight (and also cranked)
types of ring spanners can be obtained.

Flare Nut spanners are designed with a gap in the ring, which allows the spanner
to be placed over a pipeline or electrical loom, and then to be moved onto the
hexagon of the union nut or plug.

Sockets spanners (but, more commonly, simply referred to as sockets) typically,


have a six- or twelve-pointed opening, designed to enclose different sized nuts
and bolt heads in one end, with a square hole, for the standard T bar driver (or
an alternative turning device), in the other end.

Socket sets are available in a variety of drive sizes. However, in aircraft


maintenance, the " square drive and the 3/8" square drive are the most popular.
Other sizes available are the ", " and 1" square drives.

370280148.doc Issued December 2002 Page 41


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

Sockets are available in both Imperial and Metric sizes (though the drive sizes
tend to be quoted in Imperial units) and can be used with several accessories,
which greatly facilitate the use of the sockets and extend the range of their
application.

The socket spanners are usually supplied in complete sets, of incremental sizes
to suit various tasks. Deep sockets are used where a bolt extends further through
a nut than normal, preventing the use of a standard socket. They are also used to
remove spark plugs from piston-type aero engines.

The main accessories, supplied with socket sets, can (in addition to the standard
T bar driver) include:

Ratchet Handles
Drive Bars
Speed Braces
Extension Bars
Universal Joints
Converter/Adapters.

Ratchet handles allow the turning to continue, even if the space does not allow
full rotation of the normal T bar driver. Most ratchets are reversible, either by the
use of a selector lever or by the square drive being able to be floated through
the mechanism, to be available on both sides of the ratchet handle.

Drive bars are usually produced with long handles and so, should normally be
used only to break the stick of a tight nut and not for tightening up. These are
also known as breaker bars or knuckle bars.

Speed braces can have a socket or screwdriver blade snapped onto their ends.
They are normally used to turn down nuts or screws, which have many threads
before they tighten-up. Final tightening is completed using either a T bar, a
ratchet handle or (more usually) a torque wrench.

Extension bars are used where access for a standard drive handle is restricted.
Extension bars are made from forged alloy steel and come in a range of nominal
lengths from 50 mm (2 in) to 1 m (39 in).

Universal joints allow tightening of nuts, bolts and screws where it is not possible
to obtain access in a straight line. They function better if the angle they are
working through is not too great.

Converter/Adapters allow sockets from one type of drive to be used with another
type. For example, a 3/8" drive socket with a 1/4" drive ratchet would use a step-
up or step-down adapter. Care must be taken, when using larger drive
equipment on smaller sockets, that the nuts or screws are not over tightened.

Page 42 370280148.doc Issued December 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

Certain bolts and screws, are sunk (or set) below the surface of a component and
are used for locking purposes. These set-bolts and set-screws, have a hexagonal
recess in their heads and the tool used for tightening and loosening these bolts
and screws is the Allen Key (also called Allen Wrenches).

Allen Keys are made from hexagonal-section, steel bar, suitably hardened and
tempered and are cranked at 90 to give the desired leverage. Allen keys are
supplied in a variety of sizes to locate with the recesses in the various screws and
bolts. They are classified (in Metric or Imperial units), by the dimension across the
flats of the hexagon bar from which they are made.

The holding power, of a threaded fastener is greatly increased, when it is placed


under an initial tensile load that is greater than the loads to which the fastener is,
normally, subjected. This task is accomplished, by tightening a bolt or nut, to a
pre-determined torque or pre-load.

If a fastener is under-torqued, there is danger of the joint being subjected to


unnecessary loads, leading to premature failure. When a fastener is over-torqued
then the threads are over stressed and can fail.

A Torque Wrench is a precision tool that governs the amount of force applied to a
fastener and allows accurate torque values to be applied consistently. Under
controlled conditions, the amount of force required to turn a fastener is directly
related to the tensile stress within the fastener.

The amount of torque is the product of the turning force multiplied by the distance
between the centre of the fastener and the point at which the force is applied
(usually the length of the wrench handle). Table 4 shows various units of torque,
including Imperial, Metric and SI values.

Table 4
Various Units of Torque
Imperial Metric SI
pound force foot kilogram force metre Newton metre
(lbf.ft) (kgf.m) (Nm)
pound force inch kilogram force centimetre centi-Newton metre
(lbf.in) (kgf.cm) (cNm)

370280148.doc Issued December 2002 Page 43


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

There are, again, many different designs of torque wrenches, so consideration is


given here only to three basic types of torque wrench. They are the:

Deflecting Beam
Torsion Bar
Toggle Type.

The Deflecting Beam torque wrench, has a square drive, on one end of an
accurately-ground beam, with a handle, mounted on a pivot, at the other end.

A pointer is attached to the square drive end of the beam, whilst a scale is
attached to the beam near the handle. When a force is applied to the handle, the
beam bends and the pointer deflects over the scale. The deflection is directly
proportional to the torque applied.

The Torsion Bar torque wrench, uses the principle that a bar accurately deflects in
torsion, as well as bending, when a force is applied. The square drive is
accurately ground and has a rack gear on one end.

When the bar is twisted, the rack moves across a pinion gear in a dial indicator,
which shows the amount of bar deflection. The dial is calibrated in units of torque.

The Toggle type of torque wrench, is pre-set to the desired torque before it is put
on a fastener. When this pre-set torque is reached, a sound (a click), is heard and
the handle releases a few degrees, indicating that the set torque value has been
exerted. Once this release occurs, then all force is removed.

Note; When a castellated nut is being torque loaded, it must, first, be torqued to
the lowest value of the given torque range. The torque may then be increased
until the holes are in line, but before the maximum torque value is reached.

Page 44 370280148.doc Issued December 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

4.2 Common Power Tools

Powered tools have to be treated with respect because they can injure, and in
exceptional cases, can cause death if they are incorrectly operated. Before using
any powered machine/tool, personnel must make sure that:

They have been properly trained and are currently authorised to use it
All protective guards and fences are securely in place
No part of the body or clothing can come into contact with moving parts
Protective clothing is fastened and neck ties (if worn) tucked in or removed
All rings and other jewellery are removed
Safety glasses/goggles are worn wherever there is a debris risk
Where necessary, the appropriate fire extinguisher is readily to hand
A safety mat is available to stand on where electrical machinery is used
Machinery is checked for any Warning notices indicating it is unsafe for use.

Possibly the most common method of powering tools is through the use of
electricity, which is readily available from the ac mains supply and can also be
provided from portable, dc batteries.

However, because of the fire hazard, associated with the operation of electrically
powered tools, and where there is a possibility of flammable vapours being
present, pneumatically powered hand tools are provided for aircraft maintenance
tasks, such as drilling, cutting, shaping, screw driving, riveting, nut running and
setting.

As previously mentioned, these pneumatic tools may be operated from a fixed air
supply gallery, in a workshop or hangar, or from a mobile air compressor.

4.2.1 Electrically Powered Pillar Drills

Electrically powered, Pillar Drills, are used for heavy-duty drilling tasks, where
larger drill sizes and rigid holding-down of the workpiece are required.

Pillar drills also have an advantage in that they are equipped with a method of
altering the speed of rotation (rpm) of the chuck to suit the material being drilled
and the size (and type) of the drill being used.

This flexibility is needed to enable drills of all sizes to cut efficiently and safely for
different types of materials. If the rpm of the machine were constant, then the
cutting speed of any drill being used would be dependent upon the diameter of
the drill. Small drills would cut slowly and larger drills more rapidly.

370280148.doc Issued December 2002 Page 45


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

For example, at a constant rpm, a point, on the circumference of a drill with a


diameter of 10 mm, will travel twice as far, and cut at a much faster rate, than a
similar point on a drill, which has a diameter of 5 mm. At this excessive rpm, the
larger drill would become very difficult to control and would, almost certainly, be
damaged by over-heating.

The speed of rotation of most fixed drilling machines may be changed, either by
means of a gearbox or by a system of coned pulleys.

The work, being drilled, must be clamped in a manner that will prevent any
movement during the drilling operation. Failure to observe this precaution may
result in spoilt work, a broken drill and it may also cause serious injuries.

Larger pieces of work are clamped directly to the drilling table of the machine,
whereas small items are usually held in a machine vice, which has smooth jaws.

It is essential to ensure that the point of the drill aligns with the centre punch mark
and adequate cutting fluid (where required) is applied before drilling starts.

4.2.2 Electrically Powered Hand Drills

These drills are useful in certain locations when work cannot be taken to a fixed,
pillar drill and where there is no risk of fire from inflammable materials or vapour.
They are quicker than the hand brace and, when used correctly, can be perfectly
safe.

The smaller electric drills have a 6.5 mm (") chuck, whilst other larger drills can
be found with chuck sizes up to 13 mm (") and larger. This size classification
simply indicates the largest size of twist drill that the chuck will hold.

Battery powered (cordless), drills offer more freedom than ac powered or


pneumatically powered drills, but they should not be used in the vicinity of
flammable vapours as they are not considered to be spark proof.

4.2.3 Pneumatically Powered Hand Drills

The type of pneumatic drill, used for a specific task, depends very much on the
access available. Three typical types of pneumatic hand drills, in common use,
are the:

Straight Drills
Angled Drills
Pistol Grip Drills.

Straight Drills have conventional chucks and keys to accept twist drills with
diameters up to 5 mm (13/64) and have push-button operation. These drills can be
used for all conventional drilling operations where direct access is possible.

Page 46 370280148.doc Issued December 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

Angled Drills are available for drilling holes in positions where access is not
possible with straight types. The most common types of angled drills are the
Angled and Offset Head drills (refer to Fig. 30), both of which will accept twist
drills with diameters in sizes up to 4.8 mm ( 3/16). Each drill size requires its own
chuck collet, which is tightened into place with collet spanners.

Pistol Grip Drills (refer to Fig. 30), have standard chuck and key arrangements,
accept twist drills of diameters up to 8 mm (5/16) and have a trigger operation.

All drills may be found with built-in filters, pre-set compressed air pressure-
reducing devices and a requirement for lubrication. The air supply is normally via
a quick release, male and female coupling (bayonet type), allowing the tool to be
moved from place to place, as the work requires.

Typical Angled and Pistol Grip Pneumatic Hand Drill


Fig. 30

370280148.doc Issued December 2002 Page 47


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

4.2.4 Pneumatically Powered Riveting Hammers

The two basic types, into which these hammers may be divided, are:

Short-Stroke: fast-hitting hammers, which produce light blows


Long-Stroke: slower-hitting hammers, which produce heavy blows.

The short-stroke hammers are usually used for 3/32" or 1/8" rivets and their bodies
are made from light-weight, aluminium alloy castings.

The long-stroke hammers may be of either the slow-hitting, reciprocating type, or


may be a one-shot type, that drives the rivet set only one blow at a time, when
the trigger is pulled. These hammers are used to drive the larger rivets and are
much heavier than the fast-hitting hammers.

Different handle styles are provided for both types of hammers (refer to Fig. 31).
The Pistol Grip and Swan Neck are the most popular styles, with the Push Button
(Straight) type being available for special applications where access is not
possible for either of the more popular styles of hammer.

Pistol Grip

Swan Neck

Push Button or
Straight

Pneumatic Riveting Hammers


Fig. 31

Page 48 370280148.doc Issued December 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

4.2.5 Pneumatic Miller (Microshaver)

Certain hollow rivets leave a mandrel projecting from the work after the closing
action. These are removed, leaving a flush surface, by careful use of a Miller or
Microshaver (refer Fig. 32). The miller has an adjustable stop, to prevent the
cutting tool (which rotates at high speed), from damaging the aircraft skin. Two
rubber feet give the tool stability during the cutting operation.

When the shank of the rivet is closed into a countersunk hole (where the rivet is
installed from inside the aircraft skin), there can be a small amount of metal
projecting above the skin line. This excess metal is also removed using a miller.

Unformed Formed Milled


Rivet Rivet Rivet

Pneumatic Miller
Fig. 32

4.2.6 Nibblers

Nibbler are tools used for rough cutting small-to-medium sized holes in skins,
radio chassis, instrument panels and other light alloy sheets. Whilst a hand-
operated nibbler can, occasionally, be found in use, the powered nibbler
(powered by either electricity or compressed air), is the most common type of
tool.

The machine operates by using a reciprocating punch to cut a groove out of the
metal, in small bites or nibbles. The holes, that have been nibbled, have to be
filed and cleaned afterwards, to the limit marks of the true hole.

One limitation, of the powered nibbler, is that it can become uncontrollable, if it is


not held securely by the operator. Care and skill will, thus, be required to take
advantage of the benefits of the tool, namely its fast removal of metal when hole
cutting is involved.

370280148.doc Issued December 2002 Page 49


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

4.2.7 Pneumatic Tool Maintenance

When used, maintained and stored correctly, air operated tools have a long and
trouble-free life. They will not, however, tolerate lack of lubrication, nor the entry
of moisture and foreign particles introduced via the air supply. These effects can
be reduced by:

Draining the oil and water traps in the air supply system at least daily and
more often if the tools are in prolonged use.
Ensuring that both the male and female parts of the air supply couplings are
clean before the connection is made.
Before using a tool, introducing the specified lubricating oil into the air supply
opening, in the correct quantity.
Before the tool is stored, after use, repeating the lubricating procedure and
operating the tool as slowly as possible, to distribute the lubricant throughout
the tool.

4.2.8 Abrasive Wheels

The most common types of Abrasive (or Grinding) Wheels, found in workshops
are the double-wheeled, bench-mounted machines, with a coarse abrasive
wheel, used for rapid metal removal, and a finer grade wheel, used for smoother
work. Protective guards are secured around the moving parts, for the protection
of the operator, and adjustable rests are provided for the support of tools, during
grinding operations.

A word of caution is necessary here, because of the terms that are (carelessly)
applied to the various abrasives, which may be used in engineering procedures.

The two main types of abrasives, used for grinding wheels, are:

Aluminium Oxide or Corundum: next in hardness to diamond, the blue variety


of which is the sapphire, while the red variety is the ruby
Silicon Carbide: formed by the fusing together of silica (or sand) with carbon,
in an electric furnace.

Aluminium Oxide (Corundum), abrasive wheels are used for steel and other
ferrous metals of high tensile strength.

Silicon Carbide (better known under the trade name of Carborundum), wheels
are used, primarily, for hard, brittle metals such as cast iron, but may also be
used for grinding aluminium, brass, bronze or copper.

Wheels, which are designated for use with steels, must NEVER, under any
circumstances, be used for the grinding of any other materials, and in particular,
NOT soft materials (light and copper alloys, wood, plastics etc.).

Page 50 370280148.doc Issued December 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

These materials are liable to clog the wheel and, if ignited by a spark, will cause
the wheel to explode, with devastating consequences.

Only authorised personnel are allowed to use abrasive wheels and, before use, it
is mandatory to ensure that:

The machine is securely attached to the bench or wall


The wheels are secure, not chipped and have no excessive bearing play
The operators clothes are not loose or in danger of fouling the wheel
Suitable fire extinguishers are available
All guards are correctly attached and secure
The tool rests are set at minimum distance, clear of the wheels
Protective goggles, in addition to any safety screens, are worn
The operator stands on an insulated mat, where provided.

During grinding operations, the item, being ground, should be moved in alternate
directions, across the width of the wheel, so that the grinding area of the wheel
will remain flat and true and will not become dangerously grooved.

An uneven or grooved wheel will require dressing (and, possibly, need being
trued) by a qualified dresser, using special fixtures and extra-hard tools.

Care must be taken, during grinding, to ensure that tools do not become
overheated. Cutting tools (chisels, punches etc.) will have their temper drawn
from them if they get too hot, so that it is necessary to ensure that the item is kept
as cool as possible, by the frequent use of water or, possibly, a directed jet of
cooling air.

After completion of the grinding task, the machine should be switched off, but it
should not be left until the wheels become stationary, as this takes a little time
and (particularly in a noisy workshop), unattended, rotating wheels pose a danger
to unsuspecting personnel.

370280148.doc Issued December 2002 Page 51


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

4.3 Precision Measuring Instruments

Precision Measuring Instruments are provided to measure dimensions to a


greater accuracy than can be obtained by the use of a simple engineers rule.

Where the smallest graduation on a rule is usually either 1 mm or, perhaps, 1/64",
precision instruments are available which measure to 0.01 mm or to 0.0001.

The precision instruments mentioned here would normally be found either in a


workshop environment or in a clean room, which may be part of a companys
Quality Department.

It should also be noted that, whilst very basic forms of the different instruments
are described, in order that the principles of operation be understood, the actual
precision instruments, found in workshops and clean rooms may appear quite
different and, in all probability, will possess digital readout facilities.

4.3.1 External Micrometers

An External Micrometer (refer to Fig. 33), as the name implies, is used for
measuring (or testing the level of accuracy of) the external sizes of objects.

Graduated Barrel with Fiducial Line

Ratchet Stop
Spindle

Anvil

Graduated Thimble
Locking Ring

Frame

External Micrometer
Fig. 33

The standard (or common) external micrometer consists of an appropriately


shaped frame, to one end of which is attached an internally threaded barrel (or
sleeve).

Page 52 370280148.doc Issued December 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

A partially, externally threaded spindle, located in a hollow, tubular thimble, is able


to be screwed into (or out of) the sleeve by means of rotating the thimble.

The working tip of the spindle has an accurately machined face, to match the
equally accurately machined face of the anvil. The anvil is located at the opposite
end of the frame and, with the spindle moved sufficiently, the object to be
measured is placed between the faces of the anvil and the spindle.

The ratchet stop is used to rotate the thimble so that the spindle moves until the
object is held between the faces of the spindle and the anvil. To prevent distortion
of the frame and to ensure that the reading is constant when taken by different
users of the instrument, the ratchet stop slips (3 clicks!) when sufficient pressure
is applied to the object being measured.

The principle of the micrometer is based on the lead of the screw thread. This is
the distance the thread moves, either forwards or backwards, during one
complete revolution of the thimble. If the lead is known, together with the number
of revolutions, then the total distance the screw moves can be calculated.

The circumference of the thimble and the length of the barrel are graduated to
indicate the measurement of the object that is in contact with the faces of the
anvil and the spindle. The barrel also has a datum (fiducial) line, against which
the measurements are made, from the bevelled end of the thimble as it uncovers
the markings on the fiducial line.

The thimble is bevelled so that its graduations are brought close to those on the
fiducial line. The bevelling eliminates shadows and also lessens parallax error
when reading the measurement. The body of the micrometer usually has a matt
finish, which serves to reduce glare and, thus, aids accurate readings.

The locking ring (some micrometers have a locking lever) is used to lock the
spindle, when the instrument is employed as a fixed (or snap) gauge.

The mechanism of the external micrometer is arranged so that the spindle face
can only move between 0 - 25 mm (or 0 1in) from the anvil face and, thus, the
standard micrometer has the capability to measure items which are in this range.

For larger items, the size of the frame is simply increased in successive
increments of 25 mm (or 1in). For example, the next size of micrometer would be
able to measure between 25 mm 50 mm (1 in 2 in), the next 50 mm 75 mm
(2 in 3 in) and so on. While the frames increase in size to accommodate the
larger items, the spindle movement (of external micrometers) remains in the
range of 0 25 mm (0 1 in).

370280148.doc Issued December 2002 Page 53


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

Both Metric and Imperial micrometers (while their units of measurement are
different), are operated in a similar manner.

The Metric micrometer uses a thread pitch and, thus, a lead, of 0.5 mm (two
threads per millimetre), so that the thimble moves over the barrel a distance of
0.5 mm per revolution. The fiducial line, on the barrel, is marked in increments of
0.5 mm and 1 mm, with numerals at intervals of 5 mm (5, 10, 15, etc.) to 25 mm.

The thimble has a total of 50 markings, so that one thimble division represents 1/50
of 0.5 mm, or 0.01 mm.

When reading a Metric micrometer (refer to Fig. 34) it is, first of all, necessary to
decide on the number of divisions, on the fiducial line, which are exposed by the
thimble and to note the division on the thimble which also coincides with the
fiducial line.

The subsequent actions, to arrive at the dimension being measured, are to:

Note the number of main divisions exposed (as shown at A = 8.00 mm)
Note the additional number of sub-divisions (as shown at B = 0.50 mm)
Note the number of divisions on the thimble (as shown at C = 0.28 mm)
Add all the numbers together to provide the total dimension (8.78 mm).

Thimble (0.01 mm divisions)


Fiducial Line (0.5 mm divisions)

Barrel

30

0 5 25

C A = 8.00 mm
B
B = 0.50 mm
A C = 0.28 mm
Total = 8.78 mm
Metric Micrometer Reading
Fig. 34

Page 54 370280148.doc Issued December 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

Imperial Micrometers measure in decimals of an inch. Their screw threads have


forty threads per inch, giving a lead of 1/40" (0.025"), which is the length of each
sub-division on the fiducial line and represents one revolution of the thimble.

The thimble circumference is, now, divided into only 25 equal divisions, making
one division read 1/25 of 1/40, which equals 1/1000 (or 0.001") movement of the
spindle.

Barrel markings are made at each tenth of an inch (1, 2, 3, 4, etc) with four sub-
divisions between each main mark.

Again, in a similar manner to the Metric micrometer, when taking a dimension, it


is necessary to deduce the number of division, on the fiducial line, exposed by
the thimble. Next note the mark on the thimble which aligns with the fiducial line
and follow similar actions to those employed with the Metric micrometer.

If, for example, nineteen divisions, on the barrel of an Imperial micrometer, were
exposed, while the eighth mark on the thimble aligned with the fiducial line, then
the total dimension would consist of:

Four 1/10 divisions (sixteen 1/40 divisions) on the barrel


Three further 1/40 divisions on the barrel (making nineteen in all)
Eight 1/1000 divisions on the thimble

In this example the total dimension would be 0.400 + 0.075 + 0.008 = 0.483.

To ensure the integrity of any dimensions it is imperative that the faces of the
spindles and anvils of micrometers are kept scrupulously clean.

Micrometers should be stored in a protective case, preferably with a sachet of


desiccant (or VPI paper) and not used in extremes of temperature (the
temperature of a standards room is usually maintained at 20C).

Never store a micrometer with its spindle and anvil in contact. Changes in
temperature will cause distortion of the frame, with the obvious consequences.

Prior to use, the accuracy of a micrometer should be confirmed by doing a check


on the zero setting (with the spindle and anvil faces in contact) and a sample
check (using slip gauges or similar, accurate standard test pieces), of
measurements within the range of the micrometer.

It is possible to do adjustments with special tools, which are provided with


micrometers, but any adjustments should normally, only be done by qualified
personnel, who will then certify that the micrometer is accurate enough, to be
used for aerospace work.

370280148.doc Issued December 2002 Page 55


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

4.3.2 Internal Micrometers

Internal micrometers are used for the precision measuring of internal dimensions,
using much the same principles as those used with the external types.

While there are many designs for internal micrometers, to suit particular tasks,
space (and time) dictates that consideration be given here only to the type more
commonly referred to as the Stick micrometer (refer to Fig. 35), which is found in
both Imperial and Metric versions.

Handle
(replaced by a Grub Screw when
the Handle is not required)

Collar

2 1 0

Extension Rod
Micrometer Head

Internal Stick Micrometer


Fig. 35

An Imperial, Stick micrometer, consists of a micrometer head, with an overall


closed length of only 1, a spacing collar which has a length of " and ten
extension rods. The lengths of the rods increase in increments of one inch, with
the shortest length being and the longest 9 (e.g. , 1, 2 etc.).

The internal micrometer differs from the external type in that the thimble travel is
only half an inch and so, from closed, the micrometer is capable of measuring
internal dimensions from 1 up to 2. For dimensions greater than 2 it is then
necessary to close the micrometer and attach the smallest extension rod (),
enabling dimensions up to 2 to be measured.

By adding the spacing collar () with the smallest extension rod, measurements
up to 3 can be made, then, by removing both collar and rod and using the next
rod (length 1), it is possible to measure dimensions up to 3.
With alternate use of extension rod and rod/collar combinations, the Imperial
internal micrometer has a measuring range from 1 to 12.

Page 56 370280148.doc Issued December 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

With Metric internal micrometers, similar principles are used, but the dimensions
are, obviously, changed and are not directly related to the measurements used
with the Imperial type. The closed body length is 50 mm, thimble range is 10 mm,
the collar length is also 10 mm and the seven extension rods are provided in a
selection of lengths, which allow measurements (in increments of 20 mm), from
50 mm to 210 mm to be made.

4.3.3 Micrometer Depth Gauge

Whilst only used in specialist applications, a micrometer depth gauge is useful


when the depth of a groove or recess needs to be measured with precision.

The device (refer to Fig. 36) has a standard micrometer head (but the scale, on
the barrel, is reversed) mounted onto a precisely ground base. When the spindle
of the micrometer is flush with the face of the base, then the depth gauge reads
zero and the thimble is at its maximum distance from the base.

To measure the depth of a recess, the base is placed over the groove and the
spindle screwed down until it contacts the bottom of the groove. The reading on
the micrometer head indicates the groove depth.
0 9 8

Micrometer Depth Gauge


Fig. 36

370280148.doc Issued December 2002 Page 57


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

4.3.4 Vernier Micrometers

Some micrometers (and other precision measuring instruments), have a Vernier


scale, which enables the instrument to measure to a greater accuracy.

The Vernier principle (inventor Pierre Vernier 1580 1637)) utilises two
accurately graduated scales. The main scale may be fixed, whilst the other (the
Vernier scale), moves parallel to the main scale (refer to Fig. 37), or, depending
on the instrument (such as with micrometers), it could be the other way round,
where the main scale moves while the Vernier scale is stationary.

0 10 Main Scale

mm

0 1 2 3 4 5 6 7 8 9 10
Vernier Scale

Vernier Principle
Fig. 37

In the very basic example (refer to Fig. 37) ten divisions on the Vernier scale are
made to equal nine divisions on the main scale, so that one Vernier scale division
equals one tenth of nine millimetres (0.9 mm). The difference between one main-
scale and one Vernier division is, therefore, 0.1 mm.

When the Vernier scale is moved (to the right in this instance), so that the first of
the smaller Vernier divisions is aligned with the first main-scale division, the zeros
will be displaced by exactly one tenth of one millimetre. If this principle is
continued until the second division of each scale is coincident, then the zeros will
have moved exactly two tenths of a millimetre apart.

From this it can be seen that, whichever lines on the main and Vernier scales
align, then the zero (or datum) marks will be displaced by the small amount
shown on the Vernier scale.

Page 58 370280148.doc Issued December 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

When the Vernier principle is applied to a micrometer (refer to Fig. 38), the
Vernier scale is engraved on the barrel and is, therefore, stationary. The Vernier
graduations are scaled, usually, to represent one tenth of those on the thimble,
which enables a Vernier micrometer to read dimensions to an accuracy of one
tenth of that of a standard micrometer. Consequently the graduations on the
Vernier of a Metric micrometer represent 0.001 mm, while those on an Imperial
micrometer represent 0.0001.

The example shows a Metric micrometer reading, where the graduation on the
thimble scale does not exactly coincide with the datum line on the barrel. The
procedure for reading the dimension is to:

Note the main and sub divisions visible on the barrel (8.5) = 8.500 mm
Note the nearest thimble reading below the datum line (27) = 0.270 mm
Note the Vernier line which aligns with a thimble line (6) = 0.006 mm
Add the readings to provide the total dimension = 8.776 mm.

A similar procedure would be followed with an Imperial micrometer.

Ten Vernier Scale Marks


on Barrel.

0
8
35
6
4
2 30

0 5 25 Thimble Markings

Barrel Markings with


Fiducial Line.

Vernier Micrometer
Fig. 38

Care must be taken that it is the Vernier number, which is added, and not the
value of the main scale (thimble) reading which aligns with the Vernier line. This
is a common fault when reading Verniers.

It may also be found advantageous, to use a magnifying glass, to assist in the


reading of the smaller Vernier scale and in deciding which lines are actually in
alignment.

370280148.doc Issued December 2002 Page 59


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

4.3.5 Vernier Callipers

A Vernier Calliper (refer to Fig. 39), is a versatile precision instrument, used to


measure both inside and outside dimensions. In many situations, a Vernier
calliper is faster to use than a micrometer but, possibly, needs greater skill in
manipulation in order to obtain the correct feel and to, thus, ensure accurate
readings. Callipers, furthermore, have a working range of up to 150 mm (6 in) as
opposed to the micrometers more limited movement.

Jaws for Internal


Measurement.

Main Scale

Vernier Scale Position Lock

Jaws for External


Measurement

Vernier Calliper
Fig. 39

The Vernier scales on Imperial instruments are accurate to 0.001 inch, while
Metric Verniers have an accuracy of 0.02 mm.

With some types of calliper, nibs are located at the end of both jaws. The nib
size, which is etched on the jaw, must be added to any internal dimensions that
have been measured.

Two target points may also be found on some callipers, one on the beam and
one on the sliding jaw. These are used to set spring dividers accurately, when
they are being used in a comparator mode. The target points are exactly the
same distance apart as the reading on the Vernier and main scale.

Page 60 370280148.doc Issued December 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

4.3.6 Vernier Height Gauge

The Vernier Height Gauge (refer to Fig. 40) is similar in construction to the
Vernier calliper, except that an accurately machined, solid base replaces the fixed
jaw and the beam is mounted perpendicular to the base, which enables the
instrument to be used on a surface plate or table.

The measurements, on the beam, are read in the same manner as those on the
Vernier Calliper and they, usually, have both metric and Imperial markings on the
same face of the beam.

This instrument can be used for various purposes, when used in conjunction with
other suitable attachments. These can include measuring height, comparing and
transferring height dimensions (for marking-off), and also as a depth gauge.

Fine Adjustment Initial Locking


Control Screw

Vernier Scale

Final Locking
Screw

Scriber
Precision-Ground
Beam and Base

Vernier Height Gauge


Fig. 40

370280148.doc Issued December 2002 Page 61


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

4.3.7 Vernier Protractor

The Vernier Protractor (refer to Fig. 41) provides greater precision than is
possible when using a standard bevel protractor (or the protractor head of a
combination set), and enables angles to be measured to an accuracy of five
minutes of arc.

It consists of a grooved blade, a graduated protractor head and a stock with true
edges. The protractor head can be slid along the length of the blade to any
required position and locked.

The stock rotates about the centre of the protractor and can also be locked in any
position. The angles formed by the edges of the stock, relative to the blade, are
indicated on the protractor by an index mark 0 on the Vernier scale that is
attached to the rim of the stock disc.

The protractor scale is graduated in 180 from each end, meeting at 90 at the
middle. This enables both acute and obtuse angles to be measured.

Grooved Blade

Vernier Scale under Magnifier


Blade Locking Device

Stock Main Scale on Head

Fine Adjustment
Scale Locking Device

Vernier Protractor
Fig. 41

Page 62 370280148.doc Issued December 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

The Vernier scale is formed into twelve equal parts, which are compared to
twenty-three protractor main scale divisions (23), so that one Vernier scale
division represents 23/12 = 1 55. The difference between two protractor scale
divisions (2), and one Vernier scale division, (1 55) is, therefore, 5 of arc.

The Vernier scale has each third division numbered 15, 30, 45 and 60, indicating
the number of minutes (which make up one degree). There are two separate
scales, reading from the centre 0 to left and right, to match the two protractor
scales.

The protractor is read from the zero on the protractor scale to the zero on the
Vernier scale. This provides the number of whole degrees. The Vernier scale is
read in the same direction until the coinciding line is met. The number of the
coinciding line, (indicating minutes) must be added to the degrees, read from the
protractor scale, to obtain the total value of the angle.

4.4 Miscellaneous Measuring Tools

There are a number of specialist measuring tools, which are, usually, only found
in selected workshops or in Quality Departments. These tools are normally used
in conjunction with surface plates or tables, which are used to give the measuring
operation a standard flat surface to base the measuring upon.

4.4.1 Gauge Blocks

Gauge Blocks (also known as Slip Gauges), are, simply, precision-ground blocks
of metal that are used either alone, or in combination with other blocks, to give
extremely accurate measurements. The blocks are made from high-carbon steel
or cemented carbide and are hardened, ground and lapped so that:

Opposite faces are flat


Opposite faces are parallel
Opposite faces are , accurately, the stated distance apart.

The opposite faces are of such a high degree of surface finish, that, when two
blocks are wrung (pressed, with a simultaneous slight twist, by hand) together,
they will remain firmly attached to each other. This characteristic, of gauge
blocks, enable them to be built up, into combinations, which give sizes varying in
increments of 0.01 mm (0.0004 in), and whose overall accuracy is of the order of
0.00025 mm (0.00001 in) even with workshop grade blocks.

Gauge blocks are supplied in sets of 50, 78 or 105 pieces and protective blocks
are provided for use with inspection and workshop grades. The protective blocks
should, where possible, be used as the end blocks of all combinations, and the
smallest number of gauge blocks should always be used when making up a
combination.

370280148.doc Issued December 2002 Page 63


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

4.4.2 Dial Test Indicator (DTI)

The Dial Test Indicator, or DTI, consists of a small dial, to the circumference of
which, is connected a spring-loaded plunger. When the plunger is placed on a
surface and moved over that surface (or the surface moved beneath the plunger),
any variations in the surface condition will be indicated on the dial of the gauge.

A DTI (also called a Clock Gauge) is used, not for measuring the actual size of a
component, but to indicate small differences in size or for indicating the amount of
eccentricity (parallelism, run out) of revolving parts.

Its dial is graduated to indicate thousandths of an inch or, in metric values, in


increments of 0.01 mm or 0.001 mm, depending on the sensitivity required. The
dial has the zero datum at the top (12 oclock position), with scales of equal value
to either side, which enables plus and minus values to be measured.

An important feature of the gauge dial is that the dial can be rotated by a ring
bezel, enabling it to be readily set to zero. The gauge can thus be used as a
comparator, or as an instrument for comparative measurements, as well as for
direct measurements.

Internally, the plunger has a rack (or straight) gear, which drives a small pinion.
The pinion is fixed to a larger gear, which drives a second pinion. This pinion is
also fixed to a second, larger gear, which drives a further, third, small pinion to
which the pointer of the gauge is attached.

The compound gear train magnifies the plunger movement and outputs its
displays, via the pointer, onto the dial. A spring keeps the plunger in contact with
the surface being tested.

The flatness of a surface of a workpiece, can be checked, by attaching a DTI to a


scribing block that is standing on a surface plate. The surface being checked is
set beneath the DTI plunger and the bezel is zeroed. The workpiece is moved
beneath the DTI and variations in flatness are displayed and quantified by the dial
reading. A bar may also be checked for bowing by using a DTI, attached to a
scribing block, whilst the bar is supported by V blocks.

4.4.3 Feeler Gauges

Feeler Gauges have a wide application and consist of a series of thin, flexible,
steel blades in varying thicknesses (normally from 0.04 mm to 1.00 mm or from
0.0015 in to 0.015 in). The blades are secured in a protective, metal scabbard, by
a pin. It is important that those blades not in use should be withdrawn into the
scabbard, to prevent accidental distortion, especially of the thinnest blades.

Page 64 370280148.doc Issued December 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

Feeler gauges are used to measure very small, fixed gaps between faces. The
blades are chosen to comply with the measurement given in the maintenance
instructions. Sometimes there will only be a need to use a single blade whilst, at
other times, a combination of blades may be required to achieve the given
dimension. Feeler gauges are classified by the length of the blade.

4.4.4 Screw Pitch and Radius Gauges

These gauges are used to check the profiles of threads and radii, by comparison
with sets of blades held in a case much like feeler gauges. The thread gauges
are available in all thread types and the radius gauges have both an internal and
external radius.

4.4.5 Go/No-Go Gauges

Where a single dimension has to be repeatedly measured, a comparator-type of


gauge is used which checks, simply, whether a component is within a pair of
dimensions, usually referred to as maximum and minimum dimensions. These
gauges are referred to as GO/NO-GO gauges (Fig 42) and, providing the item
being checked passes through one jaw of the gauge, (the GO dimension), and
fails to pass through the other jaw, (the NO-GO dimension), it is considered to
be satisfactory.

O
G
O GO NOGO
N
G
O
Plug Type Gauge

Calliper or Snap Gauge

Limit (GO/NO-GO) Gauges


Fig. 42
4.4.6 Straight Edges

Straight Edges can be found in a variety of types, from a precision-ground rule, to


heavy-duty, cast iron straight edges, (e.g. the camel back straight edge). The
lighter straight edges are used to either visually check the flatness of a surface
(by holding it up to a light), or to use feeler gauges. Heavy-duty straight edges
will, probably, be used, to check other items for straightness, by a similar bluing
method to that used on surface tables.

370280148.doc Issued December 2002 Page 65


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

4.5 Lubrication Methods and Equipment

Solid surfaces are never perfectly smooth, as the actual rubbing contact (the
friction), between two moving surfaces, is concentrated on a number of high
spots on the respective surfaces. Any load between the two surfaces tends to
wear away these high spots until the area of contact is large enough to support
the load without further deformation.

During the wearing action fragments of the surface are broken away and high
local temperatures are generated. The effects are potentially dangerous, in that
the fragments can cause serious damage to the surfaces while excess heat leads
to expansion of the materials.

The expansion is likely to cause higher frictional forces, leading to further damage
(due to more particles breaking from the surface) and can possibly result in
eventual seizure and stoppage of movement. Seizure could have disastrous
results in any moving mechanism.

Lubrication is a process for reducing friction and wear, through the introduction of
an unguent between two moving surfaces. The materials, commonly used for
these purposes, are greases and oils and this topic discusses the various
methods and equipment used in the lubrication of aerospace mechanisms.

A large number of different greases and oils are in use in aircraft maintenance. All
lubricants should be kept clean and covered to keep out foreign objects. The
correct quantity of the respective lubricant must, always, be used, as over-
lubrication may cause all manner of problems, from contamination of electrical
and mechanical equipment, to dirt and dust collecting on the lubricant residue.

Care must also be taken that lubricants do not remain in prolonged contact with
unprotected skin (and particularly eyes) as many of them are severe irritants and
present serious hazards to health. Hot oil also constitutes a danger to personnel.

4.5.1 Lubrication Methods

Grease is the preferred lubricant, in certain circumstances, for the following


reasons:

Where conditions are dirty, dusty or wet, grease will provide a sealing
medium, which will tend to prevent the entry of foreign matter into moving
parts
Grease will stay in vertical bearings, whereas oil will drain away
Grease, packed into a bearing or housing, will provide sufficient lubrication for
prolonged periods of time
Grease lubrication systems use much cheaper fittings, and less complicated
designs than those required for oil systems.

Page 66 370280148.doc Issued December 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

Grease, however, has limitations in certain situations, in that grease:

Cannot replace oil when heat needs to be carried away


Cannot be used where contamination is likely to occur
Cannot be used where debris and contaminants have to be washed away.

Greases (as with oils), are produced to a range of specifications that depend
upon the applications for which they are used. Some greases have to be water-
resistant, while all have to posses good storage characteristics and be of a
specific viscosity. A grease, generally, is required to:

Remain chemically stable when it is heated, and especially if that grease is to


be used in bearings that are running at high temperature
Be thin enough to flow into applicators and spaces, whilst having the ability to
remain in the desired location
Resist the tendency to harden at the low temperatures met at high altitudes
Retain the limits, set on its alkalinity or acidity, to prevent the onset of
corrosion.

Oils are also required to remain chemically stable and to possess (and retain) a
suitable viscosity during their useful life. In general, every oil must:

Adequately wet the surface needing lubrication


Not evaporate too much in service
Not produce gum, sludge or carbon
Not damage the material with which it normally comes into contact.

In addition to protecting surfaces from corrosion, other properties of oils include


the previously mentioned ability to wash away small particles of debris and to
remove heat from system components. The heat can be as a result of the friction
of motion, or from other sources such as the heat of combustion within a gas
turbine or piston-type aero engine.

Oil provides lubrication in two distinct phases, which are referred to as:

Boundary lubrication
Fluid lubrication.

Boundary lubrication occurs in a stationary engine, when the oil tends to drain
away from surfaces, leaving only an extremely thin film of oil, clinging to the
microscopically rough surfaces of the metals.

Boundary lubrication will assist in the initial movement of one surface against
another but, if it is not renewed, the surfaces will slide until the film disappears
and seizure follows.

370280148.doc Issued December 2002 Page 67


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

Fluid lubrication is a thin, but continuous, film of oil, separating the moving
surfaces, and so preventing metal to metal contact. The oil also acts as a cushion
between the surfaces. If, however, the oil is driven from the space between the
surfaces, possibly due to excess loading, the fluid film is reduced to almost
nothing and again, the surfaces will slide until eventual seizure occurs.

A typical example of oil fluid lubrication would be as found in a typical gearbox in


which the gears are immersed in oil or are flooded with oil from pressure jets.

Oils in a similar manner to greases, have specialised purposes which include:

Normal Lubrication
High Pressure (Gearboxes)
Extreme High Pressure (Hydraulics)
Preservation and Inhibiting of components or systems.

As a general rule, the specification will identify the lubricant that is required for
each application. It is not necessary for engineers to know the properties of every
lubricant, as component manufacturers specify the lubricants approved for use on
their equipment.

Generally, lubricating oils do not deteriorate during storage, but low-temperature


greases can suffer and must be stored in a cool place. If water gets into either
type of lubricant, the result can be very serious. Water contamination can cause:

Breakdown of normal properties under bearing loads


Oil additives rendered ineffective, giving a tendency to sludge
Failure of normal properties due to oil emulsification
Frothing of engine oil, which can cause excessive loss of oil through the
system vents.

Many contaminants, such as rust and dust in suspension, may lead to blocking of
oil passages or damage to moving parts. In grease, these solids produce a sort of
grinding paste, which wears moving parts very quickly.

When oils and greases are in storage, a number of precautions will prevent
subsequent problems. Good lubricant storage and usage demands that:

All containers have their lids firmly secured at all times when not in use
The majority of lubricants need to be stored in a cool place
Different types or groups of lubricants must be kept apart, to prevent a risk of
cross-contamination
All equipment must be kept totally clean.

Page 68 370280148.doc Issued December 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

4.5.2 Lubrication Equipment

Because of the numerous types of lubricants that are available, the equipment
used for applying those lubricants is vast and so mention is made here of only
some of the more typical equipment, which includes;

Grease Guns
Oil Cans
Risbridger Replenishing Rigs.

Grease Guns cover a wide range of tools, which are all designed to inject grease,
under pressure, into bearings and other components requiring greasing. One
common Universal model (refer to Fig. 43), - which can also be used to inject oil
- is usually supplied with four nozzles for use with different nipples. The four
nozzles are the:

Standard: Tecalamit standard sized hexagonal nipples


Miniature: Tecalamit miniature sized nipples
Push-on: Tecazerk and similar push-on nipples
Hydraulic: Used on hydraulic nipples for priming

Note: If it becomes necessary to change nozzles, it is advisable to prime the new


nozzle before its first use.

Pumping Handle

Filling Point

Adapter

Grease Bleed Point

Various Hose Lengths Various Nozzles


(Flexible and Rigid)

Universal Grease Gun


Fig. 43

The gun consists of a barrel that is closed, at one end with a spring type cap,
and, at the other end, by a pump head.

370280148.doc Issued December 2002 Page 69


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

The barrel houses a piston follower assembly. The pump head, which screws on
to the barrel, houses a lever-operated piston and a spring-loaded non-return
valve. In addition, installed in the front face of the head, is an adapter for
attaching the various nozzles. A pressure- relief valve is also incorporated into the
adapter.

For oil filling, the cap is removed, to reveal a light chain. The chain is attached to
the piston follower assembly, which is pulled out by using the chain. Once the
pump is aligned head down, the barrel is filled to approximately 40 mm (1 in)
from the top, then the piston is replaced and the cap secured.

For grease filling, the pump head is, firstly, removed. Next the cap is removed
and the piston is pulled down to the cap end. Grease is loaded from the head
end until the barrel is full. The pump head is replaced before the cap is finally
secured to the opposite end of the barrel.

Note: All guns must be clearly marked with their contents and, most importantly, a
check must be made to ensure that the gun is refilled with the same grease or oil
as stated on its label.

Oil Cans are often used to apply oils, in smaller quantities, to parts and areas
which require more exact lubrication than is possible with a general spray. Cans
are able to apply oil in droplets, without spillage, just where the oil is wanted. Oil
cans must also be clearly labelled to show the type of oil that they contain.

Risbridger Replenishing Rigs are a number of differently designed, replenishing


rigs, which are normally used to replenish engine and hydraulic systems. The
basic principle of the rigs is that, by attaching a pump assembly to normal cans of
the correct oil, the pumping action will draw the oil from the can and deliver the oil
to the tank/reservoir of the relevant system.

One of the commonest rigs is attached to a can of oil by means of integral


clamps, which seal the pump and hose assembly to the top of the can. A sharp
blow will puncture the top of the can, depositing the collector pipe into the oil and
the pump is then ready for action.

The hose end will have one of a variety of connectors (such as bayonet and
push-on). These will be of the correct type to enable connection to the relevant
system requiring replenishment, and so avoid refilling with the incorrect oil.

Note: All engineers must be careful not to attach the incorrect can to the
replenisher, although most tool stores will employ a system of labels and colour-
coding, to minimise the risk of this happening. On completion, it is normal practice
to leave the can attached to the pump (even if it is empty), as an additional
precaution against attaching the incorrect can at the next replenishment.

Page 70 370280148.doc Issued December 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

5 ENGINEERING DRAWING, DIAGRAMS AND STANDARDS

The purpose of an engineering drawing is to record and convey the designers


requirements to other, interested, people. The drawing must, therefore, include
sufficient information to enable production planning, manufacture, assembly,
testing, inspection and subsequent maintenance of the particular component or
assembly to be achieved in the most cost-effective manner.

So that there can be no misrepresentation of drawings, it is essential that the


person preparing the drawing and those using the drawing should have a
knowledge of the methods of presentation symbols, terms, and abbreviations,
used in the preparation of an engineering drawing.

This section is not intended as a standard for the production of drawings, but
should be regarded as a general guide to drawing procedures and interpretation.

The reference for drawing practices, in the United Kingdom, is that produced by
the British Standards Institution, (BSI), in their publication BS 308. There are
other standards available, which supplement BS 308, such as the Society of
British Aerospace Companies (SBAC) Technical Specification (TS) 88.

Companies, that have design approval from the CAA or the JAA, can modify
these standards to suit their own particular drawing requirements. They must,
however, publish their preferred standards of drawing, to obtain the approval of
their National Aviation Authority (NAA).

5.1 Types of Drawing

There are four main types of drawings recommended by the BSI, although there
are many other types and sub-types of drawing used at different times.

The main drawing types are the:

Single-part: unique parts or assemblies


Collective: parts or assemblies of similar shape, but of different dimensions
Combined: complete assemblies, including all individual parts on a single
drawing
Constructional: assembly drawing with sufficient dimensional and other
information to describe the component parts of a construction.

A complete set of drawings for an aircraft, and any documents or specifications


referenced on the drawings, represents a complete record of the information
required to manufacture and assemble that aircraft. The manner, in which a set of
aircraft drawings is arranged, enables any particular component, material,
dimension, procedure or operation to be traced.

370280148.doc Issued December 2002 Page 1


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

Page 2 370280148.doc Issued December 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

5.2.1 Pictorial Projections

Pictorial Projections provide a three-dimensional, single image of the object, as if


it were being viewed, in perspective, by eye (in a similar manner to a painting or a
photograph).

The main types of pictorial projections (refer to Fig. 1) may be considered as the
Perspective Projection, Oblique Projection and Isometric Projection.

A Parallel Perspective Projection is when one of the principal faces is parallel to


the picture plane.

Plan Vanishing Point

Side
Front

Parallel Perspective Projection

Plan Plan

Side Side
Front Front

45 or 30
30 30

Oblique Isometric
Pictorial Projections
Fig. 1

Whilst perspective and oblique projections are not normally, used in aircraft
engineering drawings, they may sometimes, be used in Maintenance or Overhaul
manuals, to provide initial images of uncomplicated components or to portray a
general view of a constructional assembly.

Isometric projections are the types mostly used for sketches and for the majority
of images in Maintenance and many other manuals, used in aircraft servicing.

370280148.doc Issued December 2002 Page 3


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

5.2.2 Orthographic Projections

Orthographic Projections are the types mainly used in the production of aircraft
(and most other) engineering drawings of components and structures. They are
drawn as if the viewer is infinitely remote from the object and rays (or projectors)
lead out from the object so that the projection lines of opposite sides appear to be
parallel.

This method of projection provides a two-dimensional view of only one surface of


the object. This means it must have multiple views (usually three, but there can
be as many as six) of the relevant surfaces (drawn on three mutually
perpendicular planes) to provide an accurate depiction of the whole object.

There are two conventions, used for orthographic projections (refer to Fig. 2), and
they are:

The older First Angle Projection


The more recent Third Angle Projection.

Side View Plan View


Front View

Front View Side View


Plan View

FIRST ANGLE PROJECTION THIRD ANGLE PROJECTION

Orthographic Projections
Fig. 2

The internationally recognised symbol, of the truncated cone (frustum), is the key
as to whether the First or Third Angle projection is being portrayed on a drawing.

Page 4 370280148.doc Issued December 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

The First Angle projection is being used when the truncated end of the cone is
viewed and the two concentric circles are drawn at the remote end of the cone.

In the same way, the surface of interest (of the object) is drawn remote from that
surface in First Angle projections.

Third Angle projections show the surface of interest drawn adjacent to that
surface, in the same manner that the two concentric circles are drawn adjacent to
the truncated end of the cone.

Note; It is possible, on some drawings, to find the cone reversed (end for end),
but the location of the two concentric circles, relative to the truncated end, will
always provide the information as to how the drawing is to be read.

5.2.3 Sectional Views

When it is necessary to show the internal construction or shape of a part, a


sectional view is used. The four main types of sectional views are the:

Revolved Section
Removed Section
Complete Section
Half Section.

If only the shape of a part needs to be shown, it is drawn with either a revolved or
with a removed section (refer to Fig. 3). The symbols, used for sectioning,
indicate where the object has been cut or sectioned and also indicate from
whichever direction the section is to be viewed.
A
A-A

Revolved Section Removed Section

Revolved and Removed Sections


Fig. 3

370280148.doc Issued December 2002 Page 5


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

The Revolved Section view is often used to illustrate simple items with no interior
parts. Basically, a revolved section shows how a part is sectioned and revolved to
illustrate it from a different view.

The Removed Section view is also used to illustrate simple objects. However, to
do this, the object is cut, by a cutting plane line, and a section is removed to
illustrate another angle.

Section (or Hatching) lines help to enhance the clarity of the sectioned view and
are, conventionally, drawn at 45 to the axis of the section.

Dissimilar metals, other materials, or adjacent parts of similar materials, within the
section, are indicated by the hatching lines being drawn in different directions or
with different spacing between the lines.

The usual spacing between hatching lines is, preferably, not less than 4 mm, with
the exception of small areas where they are usually not less than 1 mm apart.

Assemblies of multiple parts are often shown in Complete or in Half Section views
(refer to Fig. 4). The complete section view makes it easier to identify individual
parts within an assembly (particularly where the assembly is more complex).

Sometimes it helps to be able to see the outside of the item being sectioned, and,
if the inside of the component is symmetrical, unnecessary detail can be omitted
from the view. Both of these situations are overcome by half-sectioning the
component.

Complete Section Half Section

Complete and Half Sections


Fig. 4

5.2.4 Exploded Views

Illustrated Parts Catalogues often make use of exploded views, to show every
part of an assembly. In this type of drawing, all parts are, typically, in their relative
positions and expanded outward. Each part is identified, both by its physical
appearance and by its reference number, which is used on the Parts List. An
exploded view drawing can be of great assistance, when dismantling and re-
assembling a complex component.

Page 6 370280148.doc Issued December 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

5.2.5 Drawing Lines, Symbols and Abbreviations

Table 1 shows some of the types of line used in most drawings (as laid down in
BS 308). The lines are designed to ensure that interpretation is clear at all times.

Table 1
LINE TYPES (EXTRACT FROM BS 308)
Type Description Width Application
(mm)
Continuous (Thick) 0.7 Visible outlines and edges.

Continuous (Thin) 0.3 Fictitious outlines and edges,


dimensions and leader lines,
hatching, outlines of adjacent
parts and revolved sections.
Continuous 0.3 Limits of partial views or
irregular (Thin) sections when the line is not
on axis.
Short dashes (thin) 0.3 Hidden outlines and edges.

Chain (Thin) 0.3 Centre lines and extreme


positions of moveable parts.
Chain (thick at ends 0.7 Cutting Planes.
and changes of
direction, thin 0.3
elsewhere)
Chain (Thick) 0.7 Indicates surfaces which
have to meet special
requirements

The width of the lines, shown in Table 1, relates to the width of the nibs of the
pens which are used to complete drawings that are produced in design
departments or in drawing offices. These widths are only approximate and will
change as soon as the drawing is photocopied.

Some drawings may be completed by pencil and then the lines are differentiated
by the use of pencils, the leads of which possess varying degrees of hardness, so
that the softer leads create a blacker line while the feinter lines are drawn, using a
harder pencil.

370280148.doc Issued December 2002 Page 7


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

The lines, used for basic dimensioning (refer to Fig. 5), are depicted, using a
standard format, which permits commonality between draughtsman and engineer.
Dimensions are usually shown so they can be read when the drawing is held on
the bottom or right hand edge. This is done to reduce the number of times a
drawing is handled and, thus, potentially increases its working life.

90

6 12 50

90
80
30
3

70
35

25

Dimensioning Examples
Fig. 5

In order to save time and space, when compiling a drawing, abbreviations and
symbols, as found in BS 308, can be used. Capital letters are normally used to
ensure clarity, but lower case letters may be found when it is deemed
appropriate.

Machining symbols, for example (refer to Fig. 6), indicate the type of surface
finish that a component requires.

Type of surface finish


Lap
Value of surface finish 0.08
(mm)

Lap
0.08

Surface to be machined

Typical Machining Symbols


Fig. 6

Page 8 370280148.doc Issued December 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

5.2.6 Conventional Representations

Common features, which may appear several times on a drawing, are seldom
drawn in full, since this would take up space and time unnecessarily. Table 2
shows how some of these features are illustrated by conventional
representations, which are listed in BS 308.

Table 2
Two Examples of Conventional RepresentationS
Title Convention

External screw threads (detail)

Holes in a linear patch

5.2.7 General and Geometric Tolerances

A general tolerance is usually given for all dimensions on a drawing. Where


general tolerances are inadequate or restrictive, an individual tolerance may be
given to a dimension.

Tolerances (as discussed in Workshop Practices) may be expressed by quoting


the upper and lower limits, the nominal dimension or the limits of tolerance above
and below that dimension.

Geometric Tolerances are used where it is sometimes necessary to place


tolerances both on geometric features and dimensions, in order to control the
shape of a part adequately. A recommended system can be found in the BS 308.

This is information usually required during manufacture.

370280148.doc Issued December 2002 Page 9


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

5.3 Drawing Identification System

An aircraft engineering drawing (refer to Fig. 7), must certain data, which is used
to prove its validity (and legality). All alterations to drawings must be made in
accordance with a drawing amendment system, which will ensure amendment to
design records. If an alteration is made, a new issue number and date must be
allocated to the drawing.

To comply with legislation, procedures must be introduced to progressively


amend the total definition of the product in terms of its associated list of drawings
at specific issues. Each particular variant of a product and its state of modification
must be identifiable in relation to the appropriate list of drawings.
DRAWING No. A DRAWING ISSUE No.
APPROVAL
TC002
N/A
DATE OF ISSUE
New Drawing ALTERATION

WORKBENCH EXERCISE
No 1

15.0
65.0

45
R5 R5
25.0

10.0

60.0

115.0

1 TC002-1 Mild Steel Case Harden Riveting Block 1


Note: Stamp initials on workpiece
ITEM PART No. MATERIAL / SPECIFICATION TREATMENT DESCRIPTION QTY
before case hardening
DRAWN BY. AIRCRAFT TOLERANCE
N/A
SCALE 0.05 mm
CHECKED BY. 1:1 HURRICANE WAY
STRESS
DIMENSIONS
IN mm
uk NORWICH AIRPORT
NORWICH
N/A NORFOLK
APPROVED BY.
USED ON: engineering ENGLAND
NR6 6HB
N/A THIRD ANGLE N/A
DATE PROJECTION TECHNICAL COLLEGE
CAD GENERATED DRAWING - NO MANUAL ALTERATIONS DO NOT SCALE IF IN DOUBT ASK 19-09-01

THIS DOCUMENT IS THE PROPERTY OF KLM uk ENGINEERING LIMITED AND MAY NOT TITLE DRAWING No.
ANY ERRORS SHOULD BE
REPORTED TO THE INSTRUCTORS
BE COPIED OR COMMUNICATED TO A THIRD PARTY OR USED FOR ANY PURPOSE
OTHER THAN THAT FOR WHICH IT IS SUPPLIED WITHOUT THE EXPRESS WRITTEN
AUTHORITY OF KLM uk ENGINEERING LIMITED. RIVETING BLOCK TC002
SHEE 1 OF 1
T

Typical Drawing Data


Fig. 7

The following details indicate some of the items of information that might be found
on a conventional drawing.

Page 10 370280148.doc Issued December 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

5.3.1 Title Block

The title block is generally pre-printed and contains the essential information
required for the identification, administration and interpretation of the drawing. It is
recommended that the title block should be at the bottom of the sheet with the
drawing number in the lower right hand corner.

Adjacent to this drawing number should be the title and issue (alteration)
information. For convenience, the drawing number may appear elsewhere on the
drawing, usually inverted so it can be read whichever way it is filed.

5.3.2 Drawing Number

No two drawings should bear identical drawing numbers and a design office
should maintain a register of all drawings issued. The Drawing Number may refer
to elements such as the project identity, the group breakdown, and the individual
register number. Except for repair drawings, the Drawing Number is also
generally the Part Number.

5.3.3 Handed Parts

Drawings of handed parts usually have the left-hand, upper, inner or forward part
drawn. This item is allocated the odd number, with the opposite hand the
consecutive even number. The drawing sheet bears the legend AS DRAWN and
OPP HAND in the item quantity column. Where necessary the handed condition
is indicated by a local view or annotation.

5.3.4 Sheet Numbers

Where a complete drawing cannot be contained on a single sheet, successive


sheets are used. The first sheet is identified as SHEET 1 of X SHEETS, as
applicable and subsequent sheets by the appropriate sheet number. Where a
Schedule of Parts (Parts List), applicable to all sheets, is required, it appears on
Sheet 1.

5.3.5 Drawing Changes

Change to a design drawing, with the exception of minor clerical corrections, is


usually accompanied by a new issue number and date. New parts added to the
drawing, or drawn on parts affected by the change, take a new issue number,
and parts, which are not affected, retain the original issue number. In all cases
where interchangeability is affected, a new Drawing Number and Part Number
are allocated.

370280148.doc Issued December 2002 Page 11


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

Details of the drawing changes are recorded in the appropriate column on the
drawing, or recorded separately on an Alteration Sheet, which is referenced on
the drawing.

The issue number may, sometimes, be represented by a letter. Some


organisations use alphabetical issues for prototype aircraft drawings and
numerical issues for production aircraft drawings; thus all drawings of a prototype
aircraft become Issue 1 when production commences.

An alteration to a single part drawing may also result in changes to associated


drawings, and it may be necessary to halt manufacture or assembly of the
product. The Drawing Office system usually makes provision for the proper
recording of drawing changes, by publishing concurrently with the re-issued
drawing, an instruction detailing the effects these will have on other drawings, on
work-in-progress and on existing stock.

As a further safeguard, some organisations publish Drawing Master Reference


Lists, which give details of the current issues of all drawings which are
associated with a particular component or assembly.

5.3.6 Part Referencing

Every item called up on a drawing is given an item number, which is shown in a


balloon on the face of a drawing. No other information is given in, or adjacent to,
the balloon, with the exception of information necessary for manufacture or
assembly, such as equally spaced or snap head inside. A Schedule of Parts is,
normally, also included.

Materials such as locking wire and shimming, which are available in rolls and
sheets, will be detailed by specification number in the Part No column and the
quantity will be entered as As Required or A/R.

5.3.7 Validation of Modification/Repair Drawings

When a modification or a repair is required to be embodied into an aircraft


structure or component part, it usually necessitates the use of a working drawing
to assist with the work.

To ensure the authenticity (and legality) of the drawing, it should bear a Validity
stamp (using red ink) which is applied by the issuing department.

The stamp consists of the authorisation stamp and signature of the issuing
person and the date on which the drawing is obtained from the issuing
department. In addition the stamp should bear the words VALID TIL: followed by
a second date.

Page 12 370280148.doc Issued December 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

The additional date will be that of the date of the next scheduled revision (usually
Quarterly January, April, July, October or similar) to the relevant manual or
document from which the working drawing has been copied.

Working drawings must not be used beyond their validation date, but must be
returned to the issuing department for checking and re-validation before use.

5.3.8 Summary of Recommended Drawing Information

Table 3 provides a fairly comprehensive summary of the recommended basic and


additional information, which is likely to be found on typical aircraft engineering
drawings.

Table 3
Recommended Basic and Additional Drawing Information
Recommended Basic Drawing Information
Company Identifier (Name, Logo etc.) Drawing number
Copyright clause Descriptive title of part/assembly
Date of drawing Units of measurement
Issue information General tolerances
Projection symbol Original scale
Sheet number Warning: DO NOT SCALE
Number of sheets Grid or zoning system
Validation stamp for working drawings Signature(s)
Recommended Additional Drawing Information
Material and specification Treatment/hardness
Surface texture Finish
Screw thread forms Tool references
Sheet size Gauge references
Print-folding marks Reference to drawing standards
Supersedes Equivalent part

370280148.doc Issued December 2002 Page 13


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

5.4 Auxiliary Diagrams and Charts

In addition to the conventional Engineering Drawings, uses are made of other


diagrammatic means of presenting information, for specific purposes, during
maintenance operations. These auxiliary diagrams can include:

Electrical Wiring Diagrams


Component Location Diagrams
Schematic Diagrams
Block Diagrams
Logic Flowcharts.

5.4.1 Electical Wiring Diagrams

Electrical wiring diagrams are included in most aircraft maintenance manuals and
they will specify details such as the size (gauge) of the wires and the types of
terminals used for each application. Wiring diagrams, typically, identify each
component within a system by its part number, (and sometimes by its serial
number), and will include any changes that were made during a production run of
an aircraft.

There are several types of electrical wiring diagrams. Some diagrams show only
one circuit while others show several circuits within a system. More detailed
diagrams show the connection of wires at splices and junction boxes in addition
to the arrangement of components throughout the aircraft.

On modern aircraft, wiring diagrams can vary from a single page diagram
(applicable to a light aircraft, for example), to those of a modern jet airliner, which
might need to have many dozens of wiring diagrams to give each system and
sub-system enough clarity to make them useful.

Because some aircraft have very complex electrical and electronic systems, a
separate Wiring Manual is often produced. The Wiring Manual can include full
wiring diagrams, component location diagrams, and schematic diagrams to
provide a system overview (which show all connections to the components etc.)
to assist in trouble shooting.

Page 14 370280148.doc Issued December 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

5.4.2 Component Location Diagrams

In a Component Location Diagram (refer to Fig. 8), components, within a specific


system, are shown as they actually appear, and not as symbols or as cut-aways.

This simplifies understanding of the overall system operation.

Electrical Power
Receptacle

Component Location Diagram


Fig. 8

370280148.doc Issued December 2002 Page 15


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

5.4.3 Schematic Diagrams

Schematic diagrams can be found in maintenance manuals to represent and give


information on aircraft systems such as electrical, hydraulic, pneumatic,
lubrication, air-conditioning, and pressurisation, and also to provide details for
engine and (where applicable) propeller operation.

Coloured diagrams are not used in maintenance manuals, but a system of


hatching and shading is normally used to indicate how the system functions.

A typical electrical system schematic diagram (refer to Fig. 9), is used to give an
overview of the complete aircraft system so that maintenance and diagnosis can
be initiated. The diagram may show sources of electrical power and the
distribution of that power to a wide range of bus-bars. Each sub-system would
have an additional diagram, showing the circuits, in detail, from those bus-bars.

AC Ext DC Ext
Gen 1 Gen 2

Automatic AC Bus Transfer System

AC Bus 1 AC Bus 2

TRU 1 Battery TRU 2 Battery


Charger 1 Charger 2

Battery 1 Battery 2

Batt Batt
Bus 1 Bus 2

DC Bus Transfer System

Typical Electrical System Schematic Diagram


Fig. 9

Page 16 370280148.doc Issued December 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

5.4.4 Block Diagrams

Due to the complexity of electrical and electronic diagrams, a Block Diagram


(refer to Fig. 10) may be used to assist in certain tasks, such as trouble shooting,
because the purpose of trouble shooting is merely to locate the faulty module,
rather than to check it out internally.

The blocks can represent components, circuit boards, or replaceable modules.

RF AF
Amplifier Demodulator Amplifier

Loudspeaker

Simple Block Diagram


Fig. 10

5.4.5 Logic Flowcharts

Logic Flowcharts provide another aid to trouble-shooting, by representing the


mechanical, electrical or electronic action of a system without expressing the
constructional or engineering information.

A simple Logic Flowchart (refer to Fig. 11) can be used (by following the arrows
through the sequence), to detect faults in an operation and to provide solutions
for correcting the faults.

370280148.doc Issued December 2002 Page 17


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

Start

No
Obtain Is drill size
correct size correct?
drill
Yes

Secure drill in chuck

No Is drill speed
Adjust
drill correctly set?
speed
Yes

Align and secure work in clamp

Drill hole

Finish

Simple Logic Flow Chart


Fig. 11

Page 18 370280148.doc Issued December 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

5.5 Microfilm, Microfiche and Computerised Presentations

Due to the increased complexity of modern aircraft, the amount of information


needed, within the Maintenance, Spares and Repair manuals, has grown to an
enormous extent.

For example, the Maintenance manuals, for one modern aircraft alone, consist of
twenty volumes, each of which would be more than 76 mm (3 in) thick.

To compress even greater amounts of data, other media are utilised, to make the
information more easily available to aircraft servicing technicians. These include:

Microfilm
Microfiche
Computers (CD-ROM).

5.5.1 Microfilm

This method entails one publication being reproduced, on a roll of film and
contained in a special cartridge case, approximately three inches (76 mm)
square. The pages are sequentially copied onto the film and wound upon a drum,
within the cartridge case.

A microfilm Reader (a projector) is used, to wind the film through a gate and
display a single page of text/drawing upon a screen, which is large enough to
enable the text and illustrations to be read and understood.

Because of the condensing of the hard copy books into a small space; a
complete set of maintenance manuals can, thus, be contained in a small number
of microfilm cartridges which can be stored close to the Reader.

A number of these projectors are provided with a printing facility, that allows the
person, reading the film, to print a copy of any sheets which contain information
that is required away from the machine. All copies, removed from the microfilm
reading room, must be used once only, and not retained for later work. This
practise ensures that amendments and updates are not missed.

5.5.2 Microfiche

A similar process to microfilm, with the exception that many pages of the manuals
are reproduced on one clear sheet of film, measuring approximately 100 mm x
150 mm (4 in x 6 in). Each sheet is capable of storing a large number of pages
(over 100) of text/drawings and takes up very little space.

370280148.doc Issued December 2002 Page 19


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

The Reader is similar to the microfilm Reader except that the film slide is moved
about, beneath the viewing lens, until the relevant page appears upon the screen.

By simply pressing a button on the machine, a photocopy of the page being


viewed can be produced for remote use and, once again, any copies should not
be retained for future use.

Amendment of both this and the microfilm system is by direct replacement, with
local disposal of the unwanted items.

5.5.3 Computer CD-ROM

The use of computers, with respect to aircraft maintenance manuals, (and other
publications), has the primary advantage of the huge amount of information that
can be stored on one Compact Disc (CD).

A single computer, located within a maintenance facility, could have all the
necessary publications (such as the Maintenance Manual, Illustrated Parts
Catalogue and Wiring Diagrams), for the relevant aircraft type, held on one CD.

As with the other two systems, there should be the facility to print the necessary
information required with, of course, the limitation that the information is only valid
on-the-day, and must not be used for repetitive jobs.

Updating of computer-based systems is by the simple replacement of the relevant


CD-ROM, although there may be intermediate amendments.

5.5.4 Supplementary Information

It is important that only the current issue, of whichever system is in use, is


supplied to servicing technicians. This means that the amendment procedures
must be carefully monitored (and especially the disposal of the out-dated
material). The new amendments come with a Letter of Transmittal, from the
relevant authority, in exactly the same manner as they do with the hard copy
technical publications.

Because of the need to dispose of large amounts of information, whenever even


a minor update or amendment is carried out, it is normal to produce
Supplementary Information in hard copy form, as an intermediate source of
current information. These issues are in addition to either the film/fiche/CD-ROM
systems in use and must be not only carefully monitored, but also well publicised.

This ensures that the technicians know that the information, contained in the
system they are using, could, possibly, contain small items of out-of-date
information.

Page 20 370280148.doc Issued December 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

5.6 Aeronautical Standards

A standard is variously defined as:

Something, established for use as a rule, or basis of comparison, in


measuring or judging capacity, quantity, content, extent, value or quality, or a
level or grade of excellence
Any measure of extent, quality or value, established either by law, or by
general use, or by consent.

In the normal performance of their duties, technicians can find a wide array of
standards, establishing the characteristics of the materials and components that
they encounter in their day-to-day work of maintaining and repairing aircraft.

5.6.1 Air Transport Association Specification No. 100

Since 1 June 1956, the Air Transport Association of America (ATA), has used a
specification, to establish a standard for the presentation of technical data, by
aircraft, engine or component manufacturers, that is required for their respective
products.

This specification is known as ATA Specification No.100 (ATA 100), and its two
Chapters clarify the general requirements of the aircraft industry, with reference to
the coverage, preparation and organisation of all technical data.

Chapter 2 of the ATA 100 covers policies and standards applicable to specific
manuals and it details the names and contents of the various manuals that must
be prepared by the manufacturer. Such manuals include the:

Aircraft Maintenance Manual


Wiring Diagrams
Structural Repair Manual
Aircraft Illustrated Parts Catalogue
Component Maintenance Manual
Illustrated Tool and Equipment Manual
Service Bulletins
Weight and Balance Manual
Non-Destructive Testing Manual
Power Plant Build-up Manual
Aircraft Recovery Manual
Fault Reporting and Fault Isolation Manuals
Engine Manual
Engine Illustrated Parts Catalogue.

370280148.doc Issued December 2002 Page 21


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

Chapter 1 of the ATA 100 covers policies and standards applicable to all
publications and provides a uniform method for arranging technical material,
within the relevant publications, in an effort to simplify the technicians problem in
locating instructions and parts.

In the Arrangement of Material section, in Chapter 1 (1-2) of the ATA 100, the
standard details the use of a three-element identifier number. Each element of the
identifying number consists of two digits. The first element is designed to provide
identification of all topics or systems, within the respective manuals, by reference
to specific Chapters. The second element identifies sub-systems (sub-topics) as
Sections, while the third element identifies associated sub-sub-systems (sub-sub
topics) as Subjects.

Table 4 illustrates an example of how the ATA 100 numbering system (in this
instance using numbers ranging from 27-00-00 to 27-31-14) is used, to identify
the material which is covered at particular locations within a typical Maintenance
Manual.

Table 4
Example of ATA 100 Numbering System
First Element, Second Element, Third Element, Coverage
Chapter Section Subject
(system) (sub-system) (unit)
27 00 00 Material which is applicable to
the system as a whole (in this
instance Flight Controls).
27 31 00 Material which is applicable to
the sub-system as a whole (in
this instance Elevator and Tab
Control System).
27 31 00 Material which is applicable to
the sub-sub-system as a whole.
This number (digit) is assigned
by the manufacturer.
27 31 14 Material applicable to a specific
unit of the sub-sub-system
(Elevator Feel Computer). Both
digits are assigned by the
manufacturer

Page 22 370280148.doc Issued December 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

The subject is broken down yet further into Page Blocks to provide
maintenance personnel with more detailed information on specific topics (or sub-
topics) which relate to the Subject material.

Table 5 shows an example of a Page Block system along with the topics and sub-
topics, which are allocated to the relevant Page Block numbers.

Table 5
Example of ATA 100 Page Block Numbering System
Topic or sub-topic Page Block
Description and Operation 1 to 100
Trouble-shooting 101 to 200
Maintenance Practices (if brief) 201 to 300
(Otherwise) Servicing 301 to 400
Removal/Installation 401 to 500
Adjustment/Test 501 to 600
Inspection/Check 601 to 700
Cleaning/Painting 701 to 800
Approved Repairs 801 to 900

Note: The word EFFECTIVITY - which may appear on the left hand side of the
bottom of a page is used to identify the aircraft serial number, or manufacturers
serial number (MSN), or aircraft model to which a particular Subject topic may
refer and those numbers will be shown. If the word ALL appears adjacent to the
EFFECTIVITY then the information concerns all types of aircraft (or components),
regardless of any serial numbers.

Chapter 1 of the ATA 100 also details the policies and standards applicable to all
publications with reference to the:

Physical Requirements: Format of media (Paper, Film, Page layout/numbering


etc.) and Indexing (List of Effective Pages [LEPs], Table of Contents [TOC],
Text, Divider Cards, Sequence, etc.)
Issuance and Revision Service
Aircraft and Engine Zoning: Access Door, Port, Panel and Area identification.

Many airlines and similar companies also organise their spare parts in stores
departments under the relevant ATA specification numbers and, irrespective of
the aircraft type, information on similar components will be found in the same
Chapter and Section. A complete table of the ATA numbering system, sub-system
and titles, allows the technician to establish, precisely, where the information
required can be found in the respective manuals.

370280148.doc Issued December 2002 Page 23


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

5.6.2 International Organisation for Standardisation (ISO)

This is an international organisation, which has representatives from each


member country, usually consisting of that countrys own standardising
organisation.

5.6.3 British Standards (BS)

These are controlled by the British Standards Institution (BSI) and are the
recognised body for the preparation and promulgation of national standards and
codes of practice. The BSI represents the United Kingdom on matters pertaining
to ISO.

5.6.4 Military Standard (MS)

This standard was developed by the military, and has found its way into all
aspects of aviation. The MS (also MIL) standard has, all but, replaced the AN
system and, in many cases, former AN parts are now being produced as MS or
MIL parts.

The suffix usually consists of a letter, which identifies the item (R for rivet, S for
steel, C for cable, etc.), and a serial number. These standards apply both to
hardware and materials. For example, MIL-C-5424 is a standard 7 x 19, aircraft
cable, made of carbon steel.

5.6.5 Air Force and Navy (AN)

The AN system is one of the most widely used standards in aircraft hardware. It
was developed, together with the MS system, by the US military to ensure quality
and uniformity. Items manufactured to this standard are not limited to the military
and are found in all classifications of aircraft.

5.6.6 National Aerospace Standard (NAS)

Items of hardware used within military aviation, which have been proven
satisfactory by the aerospace industry, can be granted a NAS designation.

Page 24 370280148.doc Issued December 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

6 FITS AND CLEARANCES

For ease of manufacture and replacement, it is essential that the components of


similar mechanisms should be interchangeable. For this reason limits (tolerances
and allowances) are imposed on the manufacturing procedures.

The limits on dimensions ensure that, if any two mating parts are manufactured to
the tolerances and allowances, stated on the drawing, then they will assemble
without the need of further hand working or machining to achieve the required
standard of fit.

Because shafts are much easier than holes to machine small diameters, the main
systems of Limits and Fits, for engineering purposes, is usually the hole-based
system. The holes are created to a certain tolerance and the sizes of the shafts
are altered to provide the required class of fit between the two items.

6.1 Dimensions

Mass production has long been the basis of the approach to the most economic
methods of manufacturing and the complete replacement of a defective item is
common practice in the maintenance of aircraft and aerospace components.

For this reason, limits are imposed on the manufacturing processes, to ensure
that, if any two mating parts are manufactured to the dimensions as stated on the
relevant drawings, then the parts will assemble without need of further major
adjustments and in the least time possible.

The limits are based on the allowances and tolerances imposed on the
dimensions of the manufactured parts. These dimensions will be given the
accuracy required by the designer of the respective parts.

6.1.1 Allowances

An allowance is a difference in dimension that is necessary to give a particular


class of fit between two parts. If, for example (and using a typical limit system), a
shaft were required to locate with a corresponding hole in a component. Then, to
assist in the economy of manufacture, either the hole or the shaft is made as
accurately as possible to the nominal size and an allowance is applied to the
associated item. The term shaft also includes bolts and pins.

If the shaft is constant and the hole varies in size, then the system used is said to
be shaft-based. If the hole is constant and the shaft varies in size, then the
system is hole based. The hole-based system is the one in more general use.

370280148.doc Issued December 2002 Page 1


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

Page 2 370280148.doc Issued December 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

Table 1 shows that tolerances may be stated in one of three ways, using a hole
that has a nominal size of 100 mm diameter and a tolerance of 0.02 mm as an
example.

Table 1
TYPES OF TOLERANCES
Bilateral 100 mm 0.01 mm
Unilateral 100 mm + 0.02 mm
100 mm 0.00 mm
Limits 100.01 mm
99.99 mm

With sheet material, such as patch plates, used in certain repairs, the dimensions
quoted in the repair scheme usually have a tolerance in one direction only, the
nominal size being the lower limit. In effect the patch plate must never be below
the nominal size, although it can be slightly over, in accordance with the repair
scheme in the manual.

6.2 Drilling Sizes for Holes

The size of hole to be drilled depends upon the purpose of that hole. A hole drilled
for a rivet with a specific diameter would differ from those drilled to take a screw
thread, or the plain shank of a bolt, of the same diameter. Similarly the size of a
hole which is to accommodate a shaft will depend on the size of the shaft and on
the manner in which the hole/shaft combination is to be used.

Additionally, if the hole is to be reamed, then it must be drilled slightly smaller


than its nominal size, to allow for the metal removed by the reamer.

Drill sizes (as discussed in the Tools topic) are fixed and can be found on charts
that list each standard drill size, together with other columns such as clearance
and tapping sizes. These charts may also include equivalent sizes displayed in
metric, fractional, letter and in the number/letter system.

6.3 Classes of Fits

There are three principal classes of fit, between shafts and holes, and they are
the:

Interference Fit: where the shaft is larger than the hole

Transition Fit: where the shaft and hole are approximately the same size

Clearance Fit: where the shaft is smaller than the hole.

370280148.doc Issued December 2002 Page 3


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

Interference Fit Transition Fit Clearance Fit

HOLE-BASED SYSTEM

British Standards System of Fits


Fig. 2

6.3.1 Newall System

In the early Newall hole-based system of limits, the holes are classified as Class
A and Class B fits. Class A holes are manufactured to a closer tolerance than are
Class B holes. Table 2 shows how the shafts are classified, using the letters F, P,
D, X, Y, and Z.

Table 2
Newall System of Fits
Class of Fit Type of Fit Remarks
Interference Force Mechanical pressure is
F required for assembly and,
once assembled, no
dismantling is likely to be
required.
Driving These are a little less tight
D than Force Fit and one
part can be driven into the
other.
Transition Push Slight manual effort is
P required to assemble the
parts. Suitable for
detachable or locating
parts but not for moving
parts.
Clearance Running Suitable for various types
X, Y and Z of moving parts. Class Z
provides the finest fit

Page 4 370280148.doc Issued December 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

6.3.2 British Standards System

The British Standard (BS 4500) hole-based system of fits (refer to Fig. 2), also
uses the basic terminology for holes and shafts. The terminologies are similar to
those used in the Newall system (and several other systems), the holes and
shafts are identified by a more extensive alpha/numeric identifier.

It can, however, be seen that, in an Interference Fit, the upper and lower limits of
the shaft are greater than the corresponding limits of the hole and, thus, force is
necessary to achieve the fit.

In the Transition Fit, the differences in the upper and lower limits of both items are
negligible so that only light effort is required to insert the shaft into the hole.

The upper and lower limits of the shaft, in a Clearance Fit, are always less than
those of the hole, so that the shaft moves easily within the hole.

6.4 Schedule of Fits and Clearances

Wear occurs at any time that there is motion between two parts. This motion can
be intentional, such as when a shaft rotates in a plain (journal) bearing or when a
roller moves back and forth over a track. Wear can also be accidental, where two
parts, that should be immovable, chafe together.

If the parts are intended to move together, then the maintenance documentation
will have a Schedule of Fits and Clearances, based on the limit system, issued for
each mechanism, used on the aircraft.

If the parts are not intended to move together, it will depend upon inspection
procedures to discover the problem and repair schemes will be initiated, in an
attempt to prevent recurrence.

The Schedule of Fits and Clearances contains tables, which specify the limits on
wear and other characteristics such as:

Ovality (of a hole or shaft)


Bow of a shaft
Twist of a shaft.

370280148.doc Issued December 2002 Page 5


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

6.4.1 Limits for Wear

The four dimensions, typically covered in wear tables are:

Dimension New
Permissible Worn Dimension
Clearance New
Permissible Worn Clearance.

Dimension New relates to the size of the part when new, and will show the
relevant tolerances.

Permissible Worn Dimension refers to the size to which a part may wear before it
must be rejected as unserviceable. Parts, which are not worn beyond this size,
can be used again, providing a suitable mating part is chosen to keep the
clearance within the permissible figure. This will frequently involve choosing a
new part to mate with the worn part.

Clearance New is the desired clearance in limit form. Interference fits are quoted
as negative clearances.

Permissible Worn Clearance refers to the maximum allowable clearance when


reassembling the component.

6.4.2 Limits for Ovality

This usually occurs as a result of the surface wearing, through friction or linear
movement. Ovality and can apply equally to holes and shafts (refer to Fig. 3).

Holes may be tested for ovality, using such instruments as Go/No-Go gauges,
internal micrometers, or callipers, as were previously discussed in the Tools topic
of this course.

A shaft may be tested for ovality, by the use of snap gauges, external callipers
and micrometers, which were, again, discussed in the Tools topic.

It is important to test for ovality of a shaft, before testing it for bow, as the results
may be suspect if bow is done first.

Bow in a shaft can be determined, in a workshop, by utilising V blocks, a surface


gauge and a DTI (in conjunction with a surface table).

Page 6 370280148.doc Issued December 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

Wear

Wear

HOLE SHAFT

Ovality of a Hole or a Shaft


Fig. 3

6.4.3 Limits for Bow

When dealing with shafts and tubes, it is vital that not only are the ends square
with each other, but that the centreline of the complete shaft or tube is straight.

If the centre line of the shaft is not straight, then the item is bowed. When the
shaft or tube is rotating, especially at a high speed in a bowed state, there is the
risk of vibration, which can lead to mechanical failures, loosening of fasteners and
(most critical of all) fatigue.

All cylindrical items, both tubular and solid, can be given a limit to the amount of
bow permitted. For example a drive shaft, which rotates about 1500 rpm, may
have a limit of 0.25 mm (0.01 in) bow over the length of the shaft.

This ensures that, within the limits of production, the drive shafts are effectively
straight, giving the least possible vibration.

370280148.doc Issued December 2002 Page 7


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

6.4.4 Limits for Twist

Twist is the result of applied torsion on circular or square-sectioned shafts. If the


twist disappears, as a result of removing the force, then the shaft will have been
loaded below its elastic limit. If the shaft remains twisted, after removal of the
load, then it has been loaded above its elastic limit.

The action of a shaft (of whatever section), carrying a torque load is to twist in
proportion to the torque applied. The result of cyclic loading of shafts is that, at
certain times, the shafts have to be checked for permanent twist. If the shaft has
a square section, it can be checked for twist on a surface table using a DTI
mounted on a surface gauge.

Solid or tubular shafts that have to be checked for twist will possibly have witness
marks or lines engraved or etched at each end of the shaft. The shafts can be
checked, by mounting the shaft in V blocks and, then, locating these marks in the
horizontal position.

It is possible to measure the amount of twist, to which a shaft is subjected, whilst


in operation or rotation, by the use of strain gauges. These emit varying amounts
of electric current when under strain, giving an indication (on a calibrated
instrument) of the load being applied.

The designer of the aircraft or equipment will set all limits, with regards to the
distortion of parts and set them down in the relevant manuals. The methods used
to measure the distortion will either be standard procedures, such as using a DTI
and surface table etc., or will have a special procedure included in the manuals.

Page 8 370280148.doc Issued December 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

7 RIVETING

Rivets are a non-detachable form of fastening device, used extensively on


aircraft, to secure the items of components built up from sheet metal. They are
ideal for forming liquid-tight joints, are cheaper, lighter in weight and are more
rapidly fastened than bolts.

Rivets, however, have the disadvantage that they are not really suitable for
tensile loads. A riveted assembly cannot be readily dismantled. Rivets, basically
fall into two classes, which are:

Solid rivets
Hollow or tubular rivets

Rivets are supplied with one head already formed, the tail being formed by hand-
operated or machine tools.

7.1 Types of Solid Rivet

Solid rivets are available in a variety of shapes and metals. The common types of
British rivet (refer to Fig. 1) are the snap head, which is used for general
purposes, the mushroom head, where less resistance to the air is essential, and
the countersunk head, where a flush finish is required.

In the USA the common heads are the universal (similar to the mushroom head)
and the countersunk head. Countersunk heads are available in a variety of
different head angles, usually 60, 90, 100 and 120, with the most common
being the 100.

Snap Head Mushroom Countersunk Head


(or Universal) Head

Rivet Types
Fig.1

370280148.doc Issued December 2002 Page 1


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

Page 2 370280148.doc Issued December 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

Pitch

Spacing

Land

Allowance
Clearance

Terminology of Rivet Locations


Fig. 2

370280148.doc Issued December 2002 Page 3


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

7.2 Types of Riveted Joints

The location of the riveting dictates the type of joint (refer to Fig. 3) that is made.
An ordinary lap joint is used on lightly loaded members and, to provide a flush
surface on one side, the joint may be joggled. Where one flush surface and
greater strength is required, the single butt joint is used. The strongest joint is the
double strap butt joint.

Lap Joint Joggled Lap Joint

Single Strap Butt Joint Double Strap Butt Joint

Types of Riveted Joints


Fig. 3

7.3 Closing Solid Rivets

This is usually done during a repair or modification to the aircraft structure. The
repair scheme or modification leaflet will detail the rivet size, type and spacing to
be used which, usually will be the existing layout and materials used in adjacent
parts of the structure. The rivet diameter will normally be approximately three
times the thickness of a single sheet of the material being joined.

The tools required to close (set) a solid rivet are a rivet snap, reaction block
(dolly) and pneumatic hammer (rivet gun). If access is restricted, then two people
will be required to complete the task, - one holding the work and one riveting.

A solid rivet may be closed as follows:

It should, first, be ensured that the plates are secured by use of gripping pins
The hole is prepared and the correct rivets obtained
A rivet, of the correct diameter and length, is inserted into the hole
The rivet head is supported in the snap and the dolly placed on the tail of the
rivet

Page 4 370280148.doc Issued December 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

Light blows are applied, with a hammer, to the snap whilst the dolly is kept on
the rivets tail
The partially formed rivet is inspected and (if satisfactory) more blows are
applied with the hammer until the rivet is formed correctly.

7.4 Closing Hollow Rivets

There are a variety of hollow rivets, designed primarily for application where there
is access to only one side of the job. These include Tucker-pop, Chobert, Avdel,
Cherry and the Hi-Lok family of modern fasteners.

7.4.1 Tucker-pop

Hand-operated pop-rivet pliers or Lazy-tongs pliers can be used to close Tucker-


pop rivets. A procedure for using the Lazy-tongs type pliers is as follows:

The Lazy tongs are fully extend and the mandrel shank inserted into the chuck
The tongs are slightly compressed and the rivet inserted into the hole in the
material being riveted
The chuck is held firmly and squarely against the material, while the tongs are
further compressed, until the head of the mandrel closes the rivet and the
stem break off.

The broken off mandrel stems, swarf, rivet heads and shanks, which are
discarded during a repair operation, must be removed after completion of the
task. The danger of such waste material fouling items such as control cables,
cannot be over-emphasised.

7.4.2 Chobert

Chobert rivets (refer to Fig. 4) are very similar to Tucker Pop rivets, excepting that
the mandrel pulls fully through the rivet and is used many times, (including some
which have a magazine facility allowing repetitive operation). To operate the tool:

The mandrel is lubricated and threaded with the rivet


The rivet is then threaded into the jaws of the tool with the operating handle
fully anti-clockwise
The rivet and mandrel are pushed fully into the tool jaws
The rivet is place into the hole, in the work, and the tool is checked for square.
The operating handle is turned clockwise, to pull the mandrel through the
rivet, and, when the resistance ceases, the rivet is secured

After closing the Chobert rivet a pin is inserted through the centre of the rivet, to
provide additional shear strength and some sealing properties.

370280148.doc Issued December 2002 Page 5


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

Mandrel

Closing a Chobert Rivet


Fig. 4

7.4.3 Avdel

Where the strength of a solid rivet and a sealed joint is required, Avdel rivets
(refer to Fig. 5) are one of the possible choices. These leave part of the mandrel
firmly in place, the top of which can be milled off to leave a flush surface finish.

Mandrel
Avdel Rivet

Mandrel milled
flush with skin

Closing Avdel Rivets


Fig. 5

Page 6 370280148.doc Issued December 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

7.4.4 Cherry Max

One of the most common riveting systems is the Cherry Max system, produced
in the USA, by Cherry Textron. The system is one of a range produced by the
company, others include Friction-lock and Mechanical-lock Cherry rivets.

Cherry Max rivets (refer to Fig. 6) consist of four components, assembled as a


single unit. The components consist of a:

Stem with a break notch shear ring and plug section


Locking collar, which locks the stem
Fastener sleeve with a locking collar dimple
Driving anvil, to ensure correct installation.

Mandrel

Driving Anvil

Formed
Locking
Tubular Collar
Rivet
Sleeve

Unformed
Locking
Collar

Bulbed
Head

Cherry Max Rivets


Fig. 6

370280148.doc Issued December 2002 Page 7


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

7.4.5 Hi-Lok

One other family of fasteners that have taken the place of rivets in certain high
load situations is the Hi-Lok (refer to Fig. 7), Hi-Lok Hi-Tigue and Hi-Lite group.

These fasteners vary from those mentioned before, not only because they are
screwed down to full closure, but they are also installed using ordinary hand tools
such as open-ended spanners or Allen wrenches, avoids the need for complex
and expensive special closing tools.

The collar is tightened onto the pin to close the two sheets of metal, and when it
reaches the correct torque the hexagonal drive portion shear off. The collar part
of the fastener may have a fibre washer attached to aid sealing properties.

Collar

Fibre Collar

Pin

CLOSING A HI-LOK RIVET


Fig. 7

7.4.6 Rivnuts

Rivnuts are a form of blind rivet, which can be used as an anchor nut, because
the internal bore is threaded to receive a bolt or screw. These fasteners can be
found with either countersunk or flat heads and are installed with a special tool,
fitted with a threaded mandrel.

This mandrel is screwed into the rivnut and, when the gun is operated, the pull
force on the mandrel expands the shank, leaving the rivnut securely fastened and
able to receive a bolt or screw after the tool is removed.

Page 8 370280148.doc Issued December 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

7.5 Inspection of Riveted Joints

Riveted joints must be inspected at all stages of production and operation. This
means that the manufacturing stages must be thoroughly inspected to ensure
that the finished work meets the required specifications.

Whilst in service, rivets must be inspected regularly, to check for a number of


faults that might have occurred, such as corrosion, fretting and fatigue.

After the rivets have been closed, they should be inspected to ensure that they
are tight and fully formed. Rivet heads must not be deformed or cracked and the
surrounding area must be free from distortion and undamaged by riveting tools.

All aircraft maintenance manuals contain diagrams of formed rivets and their
possible faults (refer to Fig. 8). These diagrams show what is acceptable and
what is not.

Clinched Head Cocked Head

Cracked Shop Head Countersinking too Deep

Typical Rivet Faults


Fig. 8

Whilst rivets that are clearly not satisfactory must be changed, care must be
taken when considering replacing those only slightly below standard. It is possible
that more harm could be done replacing them, than leaving them in place.

370280148.doc Issued December 2002 Page 9


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

If there are any signs of damage to the airframe structure, then a thorough
inspection of the whole area must be made. Hidden damage may extend beyond
the area of visible deformation, so that any riveted joint that shows an indication
of damage should be inspected well beyond the last deformed rivet.

Inspection of a rivet head for stretch can be achieved by sliding a feeler gauge
under the head or tail. A staining colour of black or grey around a rivet head is an
indication that it has stretched. If any doubt exists it may be necessary to drill out
the rivet and examine the hole for indications of elongation or tearing. Any
stretching will become apparent when the rivets are removed, as the skin will
move position.

Once the material has settled it may be necessary for the holes to be drilled out
oversize, providing this is in accord with the repair publications.

7.6 Rivet Removal Procedure

As with all maintenance tasks on aircraft, the procedure for removing solid rivets
will be detailed in the AMM. The following procedure explains a basic method of
rivet removal:

The centre of the manufactured rivet head is carefully marked with a centre
punch
Using a twist drill the same size as the rivet shank diameter, the rivet is drilled
to the depth of the head
The head is carefully removed, with a flat chisel or is prised out with a pin
punch
The remaining shank is then punched out with a parallel pin punch of the
same diameter as the rivet shank.

An alternate method, occasionally used by some manufacturers, is to drill the tail


of the rivet off first and remove the remaining shank from the opposite end.

Care needs to be taken, during rivet removal, to ensure that the least possible
damage is done to the original hole and its surrounding structure.

When removing rivets from bonded assemblies it is essential not to apply shear
loads, which are liable to part the bond.

Page 10 370280148.doc Issued December 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

8 PIPES AND HOSES

Pipes and hoses can be called upon to carry a wide variety of different fluids
within an aircraft, including fuel, hydraulic and engine oils, de-icing fluids, pitot
and static air.

The pressure within these pipes can vary from ambient to 300 M Pa (300 bar or
4000 psi). All pipes and hoses must be manufactured, installed and connected so
that no leaks occur in service, because a leak in a very low-pressure pitot air tube
can be just as dangerous as a leak in an extremely high- pressure hydraulic line.

Rigid pipelines are, generally, made from stainless steel, Tungum (Trade name
for a high-tensile, copper alloy) and aluminium alloy. Replacement pipelines are,
usually , supplied by the manufacturer, ready for installation, with the pipe bent to
the correct curvature and the pipe ends flared and provided with the appropriate
end fittings.

In certain circumstances, it may be permissible to manufacture new pipelines


from lengths of pipe. A new pipeline will be made, by cutting the basic pipe to the
correct length, attaching the correct couplings and expanding the ends by the use
of a flaring tool.

Requests for the basic pipe material will require details of the:

Metal specification (DTD, BS, AN etc.)


Outside diameter (OD)
Gauge of the wall thickness (SWG)
Length of pipe required.

Flexible hoses are obtained from the aircraft manufacturer using the aircrafts
Illustrated Parts Catalogue (IPC). It is possible that, in certain circumstances, a
replacement hose can be manufactured in a workshop or hose bay. Approval to
manufacture the replacement hose must be sought from the aircrafts
manufacturer.

8.1 Pipe Bending

To lessen the possibility of the pipe wall kinking when it is being bent, it may be
filled with a special alloy, which can be removed after the bending operation.
These alloys are known as fusible alloys, some of which melt below 100 C and
can, therefore, be melted out by immersion in boiling water.

The pipe is oiled first, to prevent the alloy adhering to the tube wall. It is next
plugged at one end, pre-heated and then filled with the melted alloy. Once
cooled, the pipe can then be bent as required.

370280148.doc Issued December 2002 Page 1


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

After bending, the pipe should be unloaded, by immersing it in boiling water until
all the alloy has run out. The pipe must then be cleaned internally to ensure that
any alloy adhering to the walls of the pipe is removed. This is accomplished by
using a pull through with the pipe immersed in boiling water or by using a steam
cleaner.

Page 2 370280148.doc Issued December 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

Half Bushes
Latch Fitting

Pipe Threaded Sleeve


Rotation Handle
Latch Fitting
Securing Screw

Expander Cone
Rotation Handle
Expander Cone
Threaded Sleeve

Pipe Flaring Tool


Fig. 3

The threaded sleeve is slowly fed into the end of the tube whilst simultaneously
turning the expander cone via the rotation handle. This spreads the end of the
tube until it contacts the inner face of the bushes. A correctly finished flare should
leave prescribed amount of the tube projecting from the collar.

The finished flared end with the union nut and collar can be connected to a
variety of other end fittings. These can include other pipes, and both internal and
external adapters fitted to a number of different components.

8.2.2 Standard Flared Pipe Couplings

Various types of standard flared pipe couplings (refer to Fig. 4), are available in
aircraft fluid systems. These couplings have different angles and whilst they may
look similar, they are not interchangeable. The AGS system uses a 32 flare
whilst the AN system uses flares of 74 included angle. Care must be taken to
ensure that the correct couplings are fitted when manufacturing these pipes.

370280148.doc Issued December 2002 Page 3


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

Externally coned Internally


Collar adapter coned adapter
Flared
pipe

Spherical-ended
Union
Spherical-ended adapter nipple
nut Sleeve
adapter nipple Pipe to internal
Pipe to external
cone adapter cone adapter

Pipe to pipe

Standard Flared Pipe Couplings


Fig. 4

8.2.3 Flareless Couplings

The flaring operation leaves the tube end in a stressed condition which, as the
flare takes a large amount of the vibration loadings, can result in fatigue failure.

To overcome this situation, the flareless coupling was introduced. The flareless
coupling, achieves its sealing properties by the deformation of a sleeve, built into
the coupling (refer to Fig. 5). The end of this sleeve has a sharp, hooked shape,
which is known as a pilot. It is the action of this sharp hook, cutting into the pipe,
which provides the required sealing properties.

The individual parts of the coupling are assembled and the nut is simply screwed
down on to its union until finger tight, then turned one further turn with a spanner.

This action bows the sleeve and causes it to bite into the tube at its forward end.

When the nut is slackened, the sleeve remains permanently bowed and attached
to the pipe. This pre-setting can be done either with the service union or with a
special hardened steel union that is only used for pre-setting.

Page 4 370280148.doc Issued December 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

Hooked Sleeve

Under-ightened pre-set

Correctly tightened pre-set

Over-tightened pre-set

Flareless Pipe Coupling Pre-set


Fig. 5

After pre-setting, the pipe should be inspected to ensure the sleeve is correctly
bowed (It is permissible for the sleeve to rotate on the pipe).

In service, the nut should be tightened until a distinct resistance is felt, then
tightened further, - the amount depending on the tube size and material.

Under no circumstances should the nut be tightened further to stop any leaks,
this action will permanently damage the tube end and sleeve.

8.3 Inspection and Testing of Pipes and Hoses

Before any inspections can be done, it must be ensured that the components are
scrupulously clean and that all critical areas are visible if the inspection is done
while the component is in its normal, installed location (in situ).

Rigid pipes should be inspected for signs of:

Chafing
Corrosion both externally and internally where possible
Cracking of flared ends where appropriate
Deformation and Dents
Deterioration in condition of end fittings and their threads.

370280148.doc Issued December 2002 Page 5


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

Hose assemblies should be inspected for such defects as:

Blistering Both externally and internally where possible


Burn damage or discolouration
Chafing, circumferential cracking or crazing of the outer cover
Date of manufacture to ensure that it is within its prescribed life, and that it
will remain so until the next inspection
Deterioration in condition of end fittings and their threads
Flattening, kinking or twisting.

The relevant maintenance manual will state the intervals of inspections and the
criteria which must be met before rigid pipes or hose assemblies may be
considered fit for further service.

8.3.1 Bore Testing of Pipes

Pipes should be tested to ensure that the bore is clear and dimensionally correct
after forming. One method of satisfying this requirement is to pass a steel ball,
with a diameter of 80% of the internal diameter of the pipe, through the pipe in
both directions. When the design or size of the pipe and end fittings, makes this
test impractical or when a more searching test is required, the drawing will
normally require a flow test to be performed.

8.3.2 Hydraulic Pressure Testing of Pipes

Hydraulic pressure testing consists of firstly carrying out a flow test. This means a
full bore flow by pumping fluid through the pipe and checking the flow at the open
end. If this check is satisfactory, the open end should be suitably blanked.

Once the flow test has been carried out, the oil pressure should then be built up
to that prescribed on the drawing, usually 1 times the maximum working
pressure. The duration of the test must give the pipe a chance to show any leaks
or other problems.

8.3.3 Pneumatic and Oxygen Pressure Testing of Pipes

These pipes are usually given an initial hydraulic pressure test, using water as
the test medium, followed by a compressed air test that is limited to maximum
system pressure. Using high-pressure air during the test is very dangerous and
the pipe(s) under test should be placed behind a protective screen and/or
submerged in water.

8.3.4 Cleaning After Test

After a pipe has been tested, it should normally be flushed out using a suitable
solvent, dried out using a jet of clean, dry air and blanked off, using the approved
blanks.
Page 6 370280148.doc Issued December 2002
JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

Pipes that will be used in high-pressure air and gaseous or liquid oxygen systems
must be scrupulously clean and free from any possible contamination by oil or
grease. It is normal to recommend that pipes for use in these systems are flushed
with Trichloroethane or some other suitable solvent, blown through with double
filtered air and blanked-off, with the approved blanks immediately afterwards.

8.3.5 Testing Flexible Hoses

Once the manufactured hose has been checked for satisfactory physical
condition, the hose must be flow and pressure tested. The flow test will verify
whether the hose inner lining is secure and not acting as a form of non-return
valve. This is achieved by passing the fluid through the hose assembly both ways
to confirm that there is an equal and free flow.

Where a replacement hose has been manufactured in a local hose bay, a bore
test may be done, in the same manner as that with rigid pipes, by use of a ball
bearing being rolled in both directions through the hose. In this instance,
however, the diameter of the ball should be 90% of the internal diameter of the
hoses end fittings.

The hose should then be proof-tested by capping one end of the hose and
applying the test pressure, usually twice the working pressure, to it for between
one and five minutes.

8.4 Installation and Clamping of Pipes

Prior to installation, the pipe should be checked to establish that it is of the correct
type and that there is evidence of prior inspection and testing. This may involve
checking the inspectors stamp and part number. Once the pipe has been
checked for signs of damage, dirt or corrosion, and found serviceable, it must
then be immediately installed.

When transporting lengths of pipe, especially long lengths, great care must be
taken not to kink or otherwise damage the pipe prior to installation. Once in
position, the pipes should be loosely placed into position in the supporting
clamps, and adjusted so that the connections align correctly. The connections
can then be tightened up, the clamps fastened and any bonding leads attached.

8.4.1 Pipe Supports

Multiple pipe supports are often used to save space and these can be made from
a variety of materials, such as fibre blocks, aluminium alloy, moulded rubber or
nylon. The clamp halves are usually joined together and attached to the aircraft
structure by bolts. It is important that the edges of the semi-circular recesses are
not sharp and are of the correct size for the pipe in use.

370280148.doc Issued December 2002 Page 7


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

In some instances, packing will be installed between the pipe and the clamping
material. This will usually be to reduce vibration or to insulate the pipe and clamp
material, if they are likely to suffer from electrolytic corrosion.

Individual pipe clamping is usually achieved using P clips. These are light alloy
loops with a rubber sleeve, which wrap around the pipe and are held by a single
bolt to the aircraft structure.

To avoid the risk of fretting occurring between the pipe and various parts of the
aircraft, minimum dimensions must be observed between these components,
which can be found in the AMM. The CAAIPs list these dimensions as 6 mm
(0.25 in) from fixed structure, 18 mm (0.7 in) from control rods and 25 mm (1 in)
from control cables, but the AMM must always take precedent.

8.5 Connection of Pipes

When connecting pipes with brazed, flared or flareless couplings, there are a
number of points to be considered.

Union nuts must be free to rotate and can be slid back from the end of the
pipe without fouling.
All loose items such as nipples and washers, are of the correct type and
correctly located.
All pipe ends align correctly without any undue pressure on the pipe. (Pipes
should never be forced into position, neither should they ever be pulled-up
into position by their union nuts).

8.6 Maintenance of Pipes and Hoses

The correct methods of installing pipes and hoses (refer to Fig. 6) must be
followed if damage (and possibly disaster) is not to result. Pipes attached to the
airframe structure, are often shielded and will not usually be liable to accidental
damage. Other pipes may be located in exposed positions, where they may be
susceptible to damage or corrosion.

Pipes located in wheel bays or attached to an undercarriage leg could easily be


damaged by stones and mud or corroded by thrown-up water. Some pipes may
be badly sited and may be subject to abuse from carelessly performed and
unrelated servicing activities.

Chafing can occur in many places, such as clamps and clips, so care must be
shown to eliminate or at least reduce the chances of this happening. Cracking of
pipes can occur when pulsations are present and/or the pipe has sharp bends.
This risk must also be considered when inspecting pipe runs.

Page 8 370280148.doc Issued December 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

Liquid leaks can be found by the presence of fluid, or at least dampness, on the
pipe or clamps. Gaseous leaks must be searched for using one of the proprietary
leak-detecting fluids.

The relevant AMM will give details on how a particular hose is installed in the
aircraft, but, in general, a hose should be at least 3% longer than the maximum
distance between end fittings. Consideration should also be given to the
orientation of a hose and, once correctly installed, the witness lines, marked on
the hose, should be straight.
Structure

Hose to tight

Hose twisted and under tension

Hose correct tension

Correct and Incorrect Methods of Hose Installation.


Fig. 6

8.7 Pipe Identification Tape

Once a pipe has been fitted to the aircraft, it should have system identification
tape attached to enable engineers to identify which system each pipe belongs to.
The tape comes in rolls of about 25 mm wide and uses colours, symbols and
letters to differentiate between different pipes. A small length of the tape is wound
around the pipe at convenient points.

370280148.doc Issued December 2002 Page 9


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

9 SPRINGS

Module 6 (Materials and Hardware) dealt with the various types of springs, the
materials from which they are made, their characteristics and their applications
within the aerospace industry.

Consideration in Module 7 is given only to the inspection and testing of springs.

9.1 Inspection and Testing of Springs

Springs will generally require little in the way of maintenance. Those that are in
exposed areas can become corroded over time and those in areas of high
temperature can, if they become overheated, lose their temper and cease to have
the necessary mechanical compliance to satisfy the task for which they were
designed.

Corrosion, that occurs on static springs, can reduce the loads that the spring can
carry, whilst if a spring that carries cyclic loads becomes corroded, then the
combination of fatigue and corrosion can result in a serious loss of fatigue
strength.

Over heating, usually shown as blistering of the surface protection can, in


extreme circumstances, show a change of colour of the metal due to the loss of
temper. It must be assumed in this event that the spring is not suitable for the
designed task.

It is important that any exposed springs are carefully inspected for signs of either
of the problems of corrosion and overheating.

In some instances, springs have to be checked against figures or graphs to prove


whether they are in a suitable condition to continue in service. Some checks have
to be done out at prescribed intervals whilst others are done on an opportunity
basis, such as when a brake unit a hydraulic actuator is dismantled for overhaul.

The most common check, done on coil springs is on its static measurement.

The manufacturer will publish the exact dimension of the unloaded spring with
some small tolerance, whilst the servicing technician will accurately measure the
springs length and compare the two dimensions.

Providing that the spring is within the published figures, then the spring is
considered to be serviceable.

370280148.doc Issued December 2002 Page 1


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

Page 2 370280148.doc Issued December 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

10 BEARINGS

When correctly installed and efficiently lubricated, bearings require little but
thorough, attention during service, to ensure a long working life. The majority of
bearings used in aircraft engineering are of the sealed or shielded type. These
bearing are designed to prevent the ingress of foreign matter, which will damage
or contaminate the bearing contact surfaces.

10.1 Cleaning and Inspection of Bearings

Cleaning

Before a bearing can be checked it must be cleaned thoroughly to remove any


dirt and the old lubricating fluid. The manual will dictate the cleaning process
including use of any solvent, but a typical method is as follows.

Remove any excess grease with clothes and dry compressed air, whilst
ensuring that the rolling elements remain stationary or only rotate slowly.

Soak the bearing in an approved solvent, such white spirit, to remove the
remaining grease. The solvent may be applied as a forced jet if necessary.

Dry the bearing by using clean warm and dry compressed air, again avoiding
fast rotation of any rolling elements.

Lightly lubricate all bearing surfaces with oil to prevent the onset of corrosion.

Testing

Testing a bearing is usually restricted to rotational checks and excessive backlash


or free play. Slow rotation of the rolling elements and raceway will highlight any
roughness due to damage, corrosion or wear. A serviceable bearing should have
a smooth actuation. Free play should be tested in both a radial and axial direction
and is normally done by using a DTI. Some wear is usually permitted and will
depend on the grade of fit, but any wear that leaves excessive backlash in the
system is unsatisfactory.

The rate of this wear depends on the speed the bearing is rotated at, with high
speed bearings failing quicker than those which rotate slowly or through
distances of less than one complete revolution. A bearing that has any indication
of a fault should be discarded immediately.

Due to their construction internal inspection of shielded bearings will be restricted.


Taper bearings can be dismantled and a thorough inspection of the rolling
elements and raceway surfaces can be completed.

370280148.doc Issued December 2002 Page 1


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

Page 2 370280148.doc Issued December 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

10.2.3 Installation and Misalignment

Installation damage is usually the result of an impact that occurs when a bearing
is fitted incorrectly. This may be due to a sharp strike from a drift or pressing the
wrong raceway when mounting the bearing.

Misalignment damage can be seen on the raceway of the non-rotating ring


because the rolling element wear path is not parallel to the raceway edge.
Excessive misalignment can cause high temperatures as well as heavy wear of
the cage.

10.2.4 Loose Fit

A bearing should always be mounted onto a shaft or housing with an interference


fit. If the raceway becomes loose then it will rotate on these surfaces and cause
fretting. This fretting will remove metal particles, which oxidise and leave a
distinctive brown colour. It usually occurs when the bearing outer raceway rotates
inside a worn housing. The external surface of the raceway will be scored and
discoloured as a result of a loose fitting bearing. (Refer Fig. 2)

Fig. 2
Loose Fit Damage

10.2.5 Brinelling

Brinelling marks on a bearing raceway resemble the indentations that result from
a Brinell Hardness Test. They are described as being either True Brinell or False
Brinell marks.

True Brinelling occurs when loads on the bearings raceway exceed the elastic
limit of the raceway material. Brinell marks are indentations on the rolling element
caused by an excessive static or dynamic loads.

The indentations can be seen on the raceways and will increase bearing noise
and vibration, which leads to the bearings premature failure. The damage is often
caused by dropping the bearing or installing it incorrectly. (Refer Fig. 3 Left)

370280148.doc Issued December 2002 Page 3


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

False Brinelling occurs when there is only small relative motion between the
rolling elements and raceways during non-rotation periods. It is characterised by
elliptical wear marks in the axial direction at each rolling element position (Refer
Fig. 3 Right).

If the bearing is not turning then an oil film cannot be formed to prevent raceway
wear. False Brinelling marks are normally perpendicular to the line of motion, well
defined and maybe surrounded by debris.

Fig. 3
True Brinelling (Left)
False Brinelling (Right)

10.2.6 Overheating and Lubrication Failure

Excessive heating of a bearing manifests itself as discoloration of the rings,


rolling elements and cages from gold to blue. Excessive temperatures will usually
be in excess of 400C. In extreme cases the rolling elements and raceways will
deform. A blue/black colour indicates an area close to the heat source and
changes to a silver/gold discoloration the further you move away.

Failure or lack of lubrication often has similar signs as overheating because good
lubrication should cool the material and transfer away any heat produced during
rotation. Restricted flow and excessive temperatures can also degrade the
chemical composition of the oil, making it ineffective and increase wear rates.

The outcome of either overheating or lubrication failure will always result in the
eventual failure of the bearing.

Page 4 370280148.doc Issued December 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

10.2.7 Contamination and Corrosion

Contamination is one of the leading causes of premature bearing failure. The


symptoms are dents or scratches embedded in the bearing raceway and rolling
elements, resulting in bearing vibration and wear. (Refer Fig. 4 Left)

The contaminant would be an abrasive substance that gets into the bearing, such
as sand, grit or dust. The principal sources are dirty tools, contaminated work
areas, dirty hands and foreign matter in the lubricant or cleaning solutions.

Corrosion is usually the result of a chemical attack on the bearing material by an


incompatible fluid such as moisture. It manifests itself as either black pitting
marks or red/brown rust coloured areas on the rolling elements, raceways, or
cages. It usually results in increased vibration followed by wear. (Refer Fig. 4
Right).

Fig. 4
Contamination (Left)
Corrosion (Right)

10.3 Safety Precautions

The cleaning of bearings for inspection normally involves the use of solvents, so
the appropriate PPE should be worn. This will include respiratory, eye and skin
protection by using breathing masks, goggles and inspection gloves. The
moisture from the human hand may contaminate a bearing surface, as easily as
the lubricant can cause damage to the skin through dermatitis.

10.4 Storage

If a bearing is to be used immediately after inspection, it should be lubricated with


correct lubricant and installed. If there is liable to be a delay before installation,
then the bearing should be coated in rust-preventing inhibiting oil, wrapped in
greaseproof paper, boxed and labelled. The bearing should always be stored
horizontally, in a clean dry atmosphere.

370280148.doc Issued December 2002 Page 5


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

PAGE
INTENTIONALLY
BLANK

Page 6 370280148.doc Issued December 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

11 TRANSMISSIONS

The various types of transmission mechanisms were described in Module 6


(Materials and Hardware). Here, in Module 7, consideration is given to the
inspections relative to such transmission mechanisms as:

Gears
Belts and Pulleys
Chains and Sprockets
Screw Jacks
Levers
Push-Pull Rod Systems.

11.1 Gears

Gears can be found in a wide variety of applications, throughout aircraft and


engine installations. The most common applications are those used to reduce or
increase the rotational speed of an input shaft.

Some aircraft engines utilise a reduction gearbox to slow the main shaft speed to
a lower figure for either the propeller or the fan. Accessory drive gearboxes,
actuators, flap mechanisms and some flying control runs use gears of one form or
another.

Wear in gears, assuming that the bearings are not worn, will be found on the
faces of the gear teeth. This wear shows up as excessive backlash, which can be
easily found by simply rotating the input mechanism, such as the main drive
shaft, whilst holding the output rigidly. It should be borne in mind that a small
amount of backlash is essential for the correct operation of bearings.

By rotating the input in both directions, the angular difference, when measured, is
the accumulation of wear of all the gear teeth. The maintenance manual should
give the total backlash figure for the particular train of gears, to indicate whether
the train is serviceable or if further inspection is needed.

Because the majority of gears, whether in a train or a single pair of gears, are
within some other component, any signs of wear or other problems are usually
solved by replacement of the major component.

11.2 Belts and Pulleys

It is rare to find belt drives being used on modern aircraft. Due to the risk of
slippage once the belt has taken on a slight stretch, there has to be some
method, often automatic, to retain the set tension over a long period.

370280148.doc Issued December 2002 Page 1


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

Page 2 370280148.doc Issued December 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

11.4 Screw Jacks

There is little maintenance to be carried out on screw jacks, apart from regular
greasing of all the exposed threaded portions and checks for backlash between
the nut and the screw. Some screw jacks are in the form of actuators and some
are used to drive flaps and other aerodynamic devices.

A screw jack actuator (refer to Fig 1) is a fairly simple design and correct
maintenance is vital because it is part of the flying controls. The actuator has a
grease nipple fitted, which allows not only the bearings to be kept well lubricated,
but the screw will also pick up some grease when the actuator is extended and
retracted.

In-service checks, other than lubrication will probably only include backlash
checks on the actuating shaft. These will probably mean no more than a side-to-
side hand movement of the rudder trim tab, which ensures that the movement is
not excessive.

Thrust Bearings
Control Surface Attachment

Control Input Threaded Screw Shaft

Screw Jack Actuator


Fig. 1

Another form of screw jack is that used to drive flaps up and down. This form of
jack will usually be found with a drive gearbox, transmitting the motive power to
the screw and ball nut, that connects to the flap structure.

370280148.doc Issued December 2002 Page 3


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

The rotation of the flap motor drives a number of the gearboxes simultaneously,
which transmit rotation to their respective screws. The ball nuts are all driven
down the screws and these push the flaps to their selected position.

Because the screw jacks and their ball nuts are exposed to the elements, it is
essential that all checks and lubrication required must be thoroughly done.

As previously mentioned, the screw jacks must be thoroughly greased but only
after all dirt, sand and other materials have first been completely removed.

The nuts will be checked for wear at regular intervals and this check will probably
require special tools and measuring jigs. On a day-to-day basis, the backlash on
the nut/screw combination can be checked by an up and down movement of the
flap trailing edge.

11.5 Levers

Levers can be found in numerous places within an aircraft and maintenance of


these items can vary, depending on their location and purpose. As a rule, levers
will be used to transmit thrust from one medium to another. For example, a
push/pull system may drive a lever that operates a service, with an increase or
decrease of mechanical advantage or a change of direction.

Apart from the bearings of the lever requiring lubrication, (unless they are sealed-
for-life bearings), there is little maintenance required, other than physical checks
for damage, distortion and cracks.

Page 4 370280148.doc Issued December 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

11.5.1 Push-Pull Rod Systems

The majority of aircraft push-pull systems can be found in both the flying and
engine controls (refer to Fig. 2). They may consist of a series of hollow aluminium
tubes, which have either fixed or adjustable end fittings. Sometimes, to prevent
the tubes vibrating, their length is kept short and idler levers are fitted between
each pair of tubes. As an alternative, rollers or bushes can be installed along the
length of the push-pull tubes to provide support.

Range of Movement

Engine Fuel
Control Unit
Push-Pull Rods

Pivot Point

Structure

Range of Movement
Support Arm

Push-Pull Rod Mechanisms


Fig. 2

The maintenance required for this type of control consists generally of inspection
and rigging. As the bearings in both the idler levers if fitted, and the end fittings
are normally sealed for life, the only inspections to carry out are for signs of
damage and overheating. If the pilot complained of stiff controls, then a check of
each bearing assembly would be required, to check which bearing was stiff.

Rigging of push pull rods is relatively simple. The rigging pins hold the rods and
levers in the datum position and the adjustable ends are altered until all the
connecting bolts can be inserted without any force being required.

370280148.doc Issued December 2002 Page 5


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

PAGE
INTENTIONALLY
BLANK

Page 6 370280148.doc Issued December 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

12 CONTROL CABLES

Control cables, their make up and their associated components were discussed
in Module 6. Consideration is given, here in Module 7, to the inspections relative
to control cables and components of various types.

12.1 Swaging of End Fittings

All cables, used in aircraft controls runs, have some form of end fittings attached
to each end of the cables. These end fittings are usually swaged onto the cable,
meaning that the end fitting is slid over the cable before being squeezed, to
reduce its diameter, and cause it to grip the cable very tightly.

During production of these cables, the completed end fitting will be carefully
checked, using a Go/No-Go gauge, to ensure that the cable has been gripped
satisfactorily. The finished cable assembly will also be proof tested to confirm its
suitability for use as an aircraft control cable.

12.2 Inspection and Testing of Control Cables

Once in service, the cables will be inspected regularly for a variety of possible
faults, whilst the swaged end fittings will require minimal inspection. In some
installations, red paint is applied at the junction of the end fitting where the cable
emerges, leading to a gap showing if the cable has slipped within the swaged end
fitting during normal service. Some individual ferrules, fitted to non-critical cables,
may be inspected for signs of cracking whilst in service.

It is rare for cables to be removed from service to have a scheduled proof load
test. If there is any doubt to the possibility of the cables lasting a long time in
service, they will be either checked for stretch by measuring their length under
load, or they will be given a finite life and replaced when that life is reached.

Cable systems have to receive regular inspections due to their being subject to a
wide variety of environmental conditions and wear. Their degradation, due to
wear, can take the form of wire/strand breakage (which is fairly easy to detect), or
may exist as less visible (internal) wear, or as corrosion and distortion.

12.2.1 Cable Wear

Critical areas for strand breakage are where the cable passes over pulleys or
through fairleads. Examination of cables will normally involve passing a cloth
along the length of the cable, which will both clean any dirt from it and detect
broken strands if the cloth snags on the projecting wires.

370280148.doc Issued December 2002 Page 1


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

Page 2 370280148.doc Issued December 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

The maintenance carried out on cable runs usually involves both regular
inspections and preservative measures. With the majority of cables being steel-
based, it is vital that cables, passing through high risk areas such as battery bays,
toilets and galleys, receive regular rust preventative treatments in addition to
visual inspections.

Most cables have external corrosion preventative compounds applied in varying


amounts, whilst internally they will have been soaked in some form of thin grease
or low-temperature oil to resist the formation of the difficult to detect internal
corrosion.

Normally in dry and desert atmospheres, the application of certain compounds to


cables is not permitted. This is because the adhesive properties of these
compounds will cause the sand and dust to stick to the cable and, thus, cause
extremely high rates of wear.

All controls will be monitored, by the flight deck crew, on a day-to-day basis but,
during maintenance, more subjective tests must be completed. The tension of the
cables will be measured, as will the rigging of the complete runs, to ensure that
the controls remain accurate and precise in their operation.

Whilst it is not usual to find faults on the cable end fittings, these should all be
checked for any signs of damage, corrosion and stressing of the cable at the end
fitting. Items checked will include turnbuckles and ball end fittings, to ensure that
the cable is operating at the designed angle, tension and over the correct range.

12.2.2 Bowden and Teleflex Cable Systems

A typical Bowden cable control might be a brake lever on the control column
operating a remote brake control valve.

Maintenance of Bowden cable systems is usually restricted to cleaning and


lubrication of the inner cable at regular intervals and adjustment of the outer
conduit (e.g. if the brakes needed adjustment). The lubrication would keep
moisture out of the cable to prevent it freezing at low temperatures.

The Teleflex cable system is more complex than the Bowden cable system in that
the operating cable, within the conduit, is actually a number of spirally wound
cables which surround a core tension cable, giving it support. This allows the
cable to transmit a push force as easily as a pull force, doing away with the need
for any form of return spring.

A typical use of a Teleflex system might be a throttle lever to engine fuel control
system connection.

370280148.doc Issued December 2002 Page 3


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

The Teleflex cable system is a snug fit within the conduit and, because there
might be the chance of it becoming seized, due to foreign objects, dirt or freezing,
it is vital that the inner cables are regularly removed, cleaned and lubricated with
low temperature grease. It is also important that the conduits are thoroughly
cleaned using a form of pull-through, prior to the inner cable being installed.

At longer intervals, it might become necessary to inspect the outer conduit for
signs of damage or kinking; which can cause the control to become tight or
notchy.

12.3 Inspection of Control Cable Pulleys

When inspecting cables for the previously mentioned wear and breakages, the
complete cable runs must be examined for incorrect routing, fraying, twisting or
wear at fairleads, pulleys and guards.

Pulleys must be inspected for wear (refer to Fig. 2), to detect indications of
seizure, flat spots, embedded foreign material and excessive tension. Any signs
of contact with adjacent structure, pipe-work, wiring and other controls must also
be thoroughly investigated.

Excessive Cable Tension Seized Pulley Bearing

Pulley too Large for Cable Cable Misplaced or Incorrectly Installed

Types of Pulley Wear


Fig. 2

Page 4 370280148.doc Issued December 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

13 SHEET METAL WORK

While the majority of metals can be rolled into sheet form, consideration is
confined here solely to the working with sheets of the light alloys, which are
encountered on aircraft and, in particular, those formed from aluminium alloy
ingots.

Safe working procedures were covered adequately, in the Workshop and Hangar
Safety Section of the SAFETY PRECAUTIONS topic, but there are several
additional points, which need highlighting, with regard to working with sheets of
aluminium alloy.

By definition, sheets of aluminium alloy are comparatively thin in cross-section


and, as such, they not only pose a health hazard, through cuts, when being
handled but they are, also, prone to buckling and creasing if handled carelessly.

Large sheets of aluminium alloys are, usually stored upright, on their longest
edge and supported, clear of the floor, in a wooden framework so they are
protected from damage and corrosion. Care must be taken when removing a
large sheet from its storage rack a task which normally involves at least two
persons and good communication between the carriers is important so that the
task is completed in a safe manner and no damage is done to the sheet metal.

Some sheets are covered, on one or both surfaces, with a thin protective plastic
membrane and, if possible, it may be beneficial to leave at least the underneath
protection in place while the marking out is done, to minimise the possibility of the
surface sustaining undesirable scratch marks. If no protective membrane is
applied to the sheet, then care must be taken over the condition of the surface of
the table, or workbench, upon which the sheet is to be laid for the marking out
procedures.

Other factors, which should be considered (as with all work) concern the
requirements to ensure that:

Material wastage is kept to a minimum


The task is done correctly, first time, so that valuable time, also, is not wasted.

The first point is usually obvious, due to the cost of the materials involved, but the
second point quite often gets forgotten, when work is being done, but the actual
labour costs far outweigh the material costs on a high percentage of tasks.

Repair or modification drawings must be studied very carefully, to ensure there is


no doubt about the data and dimensions provided, so that the marking out is
correctly done and the approved metal is shaped in exactly the manner that the
designer of the drawing intended.

370280148.doc Issued December 2002 Page 1


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

Page 2 370280148.doc Issued December 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

13.2 Forming of Sheet Metal Parts

Once the marking out has been verified as being correct, the forming of the final
shape of the sheet metal component can be achieved by the use of appropriate
cutting and, if necessary, bending tools.

13.2.1 Cutting

While metal-cutting tools were discussed in the earlier topic on TOOLS, mention
is made here of the manner in which the relevant tools should be used when
working with sheet aluminium alloys.

The squaring shears has already been used to produce a convenient size upon
which to work and, of course, to provide an accurate straight edge from which to
make measurements.

Note: The squaring shears must only be used to cut metal of the approved
thickness (recommended by its manufacturer) and must never be used on sheets
(or strips) of metal thicker than those specified. The alignment of the blade will be
distorted and the accuracy of its cut will be degraded if this caution is ignored.

When using shears (whether squaring or the hand type), then the cut must be
made slightly above the line. This allows for filing down to the line, which will
eliminate the possibility of stress raisers being formed at the edges of the metal,
due to the shearing action of the various types of shears.

Care must be taken when drilling aluminium sheet, due to the danger of cutting
enlarged holes in the soft, thin metal and to the tendency to distortion, caused by
the application of too great a weight on unsupported aluminium sections. Twist
drills must be of the correct type and size, with accurately-ground points, and
their passage, through the metal, must be carefully controlled at all times. Off cuts
of scrap wood should be placed behind (or underneath) sheet metal parts while
drilling is in progress and both the backing piece and the part must be firmly held,
to prevent movement during the drilling procedures.

Similarly, scrap wood should be used, as backing, when hack-sawing or filing


sheet metal and protection must be given, against possible damage, when such
components are held in the jaws of vices, by the use of soft vice clamps.

Obviously fine-toothed hacksaws (32 tpi) and second cut and/or smooth files
(used with long, smooth strokes), are the cutting tools, used in the shaping of
sheet metal parts. Files, as discussed in the TOOLS topic, must be regularly
cleaned, to prevent the build up of pinnings, and the use of file cards and chalk,
for this task, has also been, earlier, mentioned.

370280148.doc Issued December 2002 Page 3


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

13.2.2 Bending and Calculation of Bend Allowance

As previously stated, the sheet metal used for aircraft construction and repair, is
generally formed from an ingot of aluminum alloy that has been processed
through a series of rollers.

This process reduces the thickness of the material to a dimension that meets the
requirements of the design drawing. As a result of this process, the metal
assumes a grain structure, which can easily be detected in a sample of sheet
aluminum alloy.

When planning any sheet metal work process, the orientation of the metal is to be
taken into account so that any bends formed will, where practical and achievable,
be made across the grain. Where, however, strength is required along the length
of a long, channel section, then, regardless of any bends, the grain should flow
along the length of the channel.

Great care must be taken, before bending aluminium alloy, to ensure that it is of
the correct designation and heat-treatment standard. The subject of the heat-
treatments of aluminium alloys was discussed fully in Module 6 Materials and
Hardware in the topic on AIRCRAFT MATERIALS NON-FERROUS.

Some alloys must be subjected to either an annealing, or to a solution treatment


procedure before (and, again, after) bending but, as this is, usually, beyond the
scope of maintenance technicians, mention of it is merely made here to draw
attention to its requirement and for the need for vigilance when bending sheets of
aluminium alloy.

Bending of aluminium alloys is achieved either by the use of:

Specially-shaped bending bars: used for small pieces and larger angles and
between which, the sheet is clamped, in a vice, while the metal is bent, by
hitting with a hide-faced or similarly soft-headed hammer
A large, free standing, bending machine (or bending brake): in which the metal
sheet is clamped and the bend made, in one movement, by means of a
hinged bending leaf.

Caution must also be exercised when forming a bend, using the bending bars
and soft-headed hammer method, because too many blows with the hammer will
cause work-hardening of the metal, or the metal, in the bend, will become too thin
and stretched. Subsequent cracking of the metal will result from these faults

For this reason the bending brake is preferred but, in a similar manner to the
squaring shears, only the approved thicknesses of metals should be bent in these
machines, as any distortion will destroy the accuracy of the bends.

Page 4 370280148.doc Issued December 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

Square (or sharp) angles, in aluminium alloys, are only formed by adhesive,
casting, extrusion or welding methods. Whether it be the bending bars or the
bending brake method, which is used to bend aluminium alloy sheet, the bend
will always be formed around a radius, as it is not possible to create square
angles by bending without cracking the metal.

It is recommended that the radii of bends, in aircraft-grade, aluminium alloy


sheets, be not less than three times the thickness (3t) of the metal, in sheets
thicker than 22 SWG (0.7 mm) and should, preferably, be greater if possible.

It is, therefore, usual to create bends, in sheets of 20 SWG (0.9 mm), of not
less than 3 mm (3 x 0.9 mm = 2.7 mm) radius and bends in sheets of 18 SWG
(1.2 mm), of not less than 4 mm (3 x 1.2 mm = 3.6 mm) radius.

As an example, if it were required to form a right angled curve (10 mm radius)


in an 18 SWG aluminium alloy sheet, to provide two legs, effectively 76.2 mm
(3 in) in length (refer to Fig. 1), it can be seen that the actual length of metal
involved is obviously less than 2 x 76.2 mm (6 in). The total length of the metal,
required for the curve, is deduced by using the formula:
LT = L1 + BA + L2
Where LT = Total Length of Metal Required
L1 = X (r + t)
L2 = Y (r + t)
BA = Bend Allowance
X and Y = Effective Lengths of Unbent Sections
r = Radius of Bend
t = Thickness (SWG) of Metal
X = 76.2 mm

A t = 1.2 mm

L1
m
m
.2
76
= B r = 10.0 mm
Y
L2

Total Length of Metal in a Curve


Fig. 1

370280148.doc Issued December 2002 Page 5


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

The lengths of both L1 and L2 can be found by subtracting the sum of the radius
and the metal thickness from the effective lengths of the unbent sections. In
this instance, therefore, the lengths are both 76.2 11.2 = 65 mm.

To calculate the length of metal in the bend (Bend Allowance) it is necessary to


consider the fact that, when metal is bent, the metal on the inside of the bend
will be compressed while that on the outside of the bend will be subjected to
tension or stretching so that the length of metal on the inside and outside of
the bend will be different.

It may, however, be considered that there is a neutral line (at approximately


half thickness) where the compression and tensile forces cancel out. It is this
line which is taken, to calculate the length of the arc of the circumference of
the circle, which would be described by the radius of the curve. The Bend
Allowance is, thus calculated, using the formula:

BA = 2 (r + t)
360
Where r = Radius of Bend
t = Thickness of Metal
= Angle of Bend

Note: Some books use the formula:

BA = (D + t)
360

Where D = The diameter of the circle

However, as curves are normally shown as radii, in engineering drawings, the


previously given formula is preferred here.

Substituting figures, in the preferred formula, it will be seen that the bend
allowance equates to 16.65 mm (0.66 in). When this figure is added to lengths
L1 and L2, it can be seen that the total length of metal, required to form the
curve, is only 146.65 mm (5.77 in) and not 152.4 mm (6 in).

In a simple, single curve, this represents a saving in metal of only 5.75 mm


(0.23 in) but, in a multiple bend component, and with larger radii involved,
considerable savings of metal can be made by using these formulas to
calculate the correct amount of metal required to forms bends in sheet metal.

Table 1 shows data relating to bend allowances for forming 90 curves of


various radii in both 20 SWG and 18 SWG metals. Using the preferred
formula, the student should be able to calculate the bend allowances and enter
them in the empty spaces in the table.

Page 6 370280148.doc Issued December 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

Table 1
BEND ALLOWANCES (BA) FOR A 90 BEND
Inside Bend Radius BA - 20 SWG (0.9 mm)
3 mm
4 mm
5 mm
Inside Bend Radius BA - 18 SWG (1.2 mm)
4 mm
5 mm
6 mm

When the total length of sheet metal, required to form a curve, has been
calculated, it will be necessary to draw the development (refer to Fig. 2) of the
intended shape, so that the bend lines can be seen.

Unbent Bend Unbent


Section Allowance Section
65 16.65 65

Bend Lines

Development of Shape
Fig. 2

An additional line must be drawn on the development drawing before the metal is
placed in the bending brake. This line (refer to Fig. 3), is referred to as the
sighting line or the brake reference line.

It is drawn at a distance, equal to the radius of the curve (in this instance, using
the figure of 10 mm from the previous example), parallel to, but away from, the
bend line, which is under the clamping nib of the bending brake and towards the
bend line which is free of the clamping nib.

The sighting line, as the name implies, is then used, to align with the front of the
clamping nib and, in this way, allowance is made for the thickness of the metal in
the formation of the curve.

370280148.doc Issued December 2002 Page 7


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

Sighting Line
Clamping Nib

Bend Lines

Metal to be Bent

Brake Bed

Hinge Point
Bend Leaf Bends
Counter-clockwise

Use of Sighting or Brake Reference Line


Fig. 3

13.3 Inspection of Sheet Metal Work

As far as aircraft maintenance technicians are concerned, the inspection of sheet


metal work is confine to visual or assisted visual methods. Personnel who have
approval may also perform dye penetrant procedures in the search for cracks in
suspect areas.

Specially trained and approved NDT personnel may use Eddy Current, Ultrasonic
or Radiographic procedures to detect faults in aluminium alloy sheet metal work.

Page 8 370280148.doc Issued December 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

14 WELDING, SOLDERING AND BONDING

Welding, Soldering and Bonding are methods of creating permanent joints


between materials and use is made of all three methods in the aerospace
industry, primarily at the production stage and to a more limited degree during
maintenance and overhaul stages.

Within the aircraft industry welding is considered to be a specialist skill and only
suitably approved and authorised personnel can undertake welding procedures.

Approved welders must satisfy the CAA of their competency, by submitting


several test pieces of their typical work for testing and they are subjected to
similar re-tests every 12 months in order to retain their approvals.

Maintenance technicians may, however, be called upon to do some soldering and


bonding procedures so, with these facts in mind, only the basic methods of
welding will be discussed in this topic, while greater emphasis is placed upon
procedures involving soldering and bonding.

14.1 Welding

Welding may be defined as the permanent joining, by fusion, of two pieces of


material (usually metals), by the progressive melting and subsequent
solidification of the materials at the site of the joint.

The basic principle, of fusion welding of metals, is the same for all processes, in
that the surfaces, or edges, of the metal to be joined, are brought to a molten
state and allowed, or caused, to intermix (with or without the addition of a filler
metal), so that the parent metal and filler metal (if used) form a homogeneous
molten pool which, when cooled, forms the complete weld.

14.2 Methods of Welding

Welds require the application of sufficient heat energy to melt the metals involved
in the joint and the high temperatures are achieved by various methods.

14.2.1 Oxy-Acetylene Flame

The cutting of steel sections and plate material may be done by means of a flame
torch, using a mixture of oxygen, with one of the appropriate fuel gases
(acetylene, hydrogen, natural gas or propane).

For welding, however, only an oxygen and acetylene mixture will provide a
sufficiently, high heat input, needed for the welding process. The temperature of
the oxy-acetylene flame is approximately 3150C.

The oxy-acetylene method can be used for welding ferrous or non-ferrous metals
but, when welding non-ferrous metals, it is necessary that an additional material
(a flux) be used, usually with a filler metal, to assist in the fusion process.

370280148.doc Issued December 2002 Page 1


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

Page 2 370280148.doc Issued December 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

14.2.5 Flash Butt Welding

The components to be joined are set up as opposite poles in an electric circuit


and, when the current is switched on, the components are moved into and out of
contact with one another. This action causes an arc to be struck and, when
welding temperature is reached, a force is applied to both components, so that
their molten surfaces are fused together.

14.2.6 Spot Welding

A method used to join comparatively thin sheets of metal, spot welding is a form
of resistance welding. The sheets of metal are sandwiched between two, pointed
electrodes on which force is exerted as the current is applied. The heat is
generated at a local spot where the resistance to the flow of the electricity is at its
highest and the metal fuses at these spots. The pointed electrodes are made
from copper alloy and are usually water-cooled.

14.2.7 Seam Welding

The principle of seam welding is similar to that of spot welding (namely resistance
to the flow of electricity). The main difference is that in place of the pointed
electrodes, this method uses discs or wheels, which are moved along the length
of the weld. The supply of current is intermittent, so causing a spot weld to
overlap its neighbour and, thereby, form a continuous seam weld.

14.3 Inspection and Testing of Welds

The wide use of welding in industry has resulted in an increasing demand for
standards relating to welded constructions in various branches of engineering.

These standards generally include requirements for certain welding tests to be


conducted, primarily for the qualification of welding procedures and operators.

Sophisticated methods of non-destructive testing of welds include the use of


Radiographic, Ultrasonic and Magnetic Particle testing procedures, all of which
are done by specially trained, and approved, personnel. Specimen welds are also
destructively tested, by fracturing or sectioning, to test the integrity of a specific
welding procedure.

These methods are beyond the scope of unqualified personnel, so that aircraft
maintenance technicians are, usually, constrained solely to the visual inspection
of welds (following thorough cleaning of the relevant areas).

It may, however, be possible that, after suitable training, some technicians can be
granted approval to conduct limited Dye Penetrant inspection procedures on
certain welds, which will be specified in the appropriate servicing manual.

370280148.doc Issued December 2002 Page 3


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

14.4 Soldering

Soldering differs from welding in that it is done at considerably lower


temperatures so that the parent metals do not melt and fuse together.

Instead, a fusible and, usually, non-ferrous alloy (with a lower melting point) is
applied between the heated metals of the joint, such that the fusible alloy forms a
metallic bond with the parent metals and, on cooling, creates a solid joint.

The word solder does, in fact, come from the same stem as the word solid (as
does the American term, which is pronounced sodder, for the same process).

14.5 Methods of Soldering

Soldering can be divided into two basic methods, one of which uses higher
temperature ranges than the other, but both of which are conducted at
temperatures below the melting points of the parent metals of the intended joint.

The two basic methods of soldering are:

Hard Soldering: done at temperatures in excess of 500C and which include


the processes of Brazing and Silver Soldering
Soft Soldering: done at temperatures within the range of 180C to 330C,
which, consequently, create joints of lower strength (but less expense) than
those achieved by the hard soldering methods.

Note: The hard soldering processes are, normally, beyond the remit of the aircraft
servicing technician, so only brief consideration is given to them here, with more
attention being given to the soft soldering method.

14.5.1 Hard Soldering (Brazing and Silver Soldering)

Brazing, as the name implies, uses a Copper/Zinc (Brass) alloy, as the filler metal
(spelter) between the parent metals of the joint. The degree of alloying will dictate
the temperature at which the process is done but the melting point of the brazing
alloys can be as high as 880C.

Brazing is a process of joining in which, during, or after heating, the molten filler
metal is drawn into, or retained in, the space between closely adjacent surfaces
of the parts to be joined, by capillary attraction.

In general applications, workshops and small factories, a flame, directed onto the
joint area, is the source of heat. However, in the more sophisticated applications,
used in industry, heating for hard soldering may be provided by a:

Gas, oil or electrically heated, closed furnace


High-frequency (HF) induction coil.

Page 4 370280148.doc Issued December 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

As with welding, it is necessary to employ the use of a flux material to assist the
fusion of the filler with the parent metals and to prevent oxidation of the joint.

The flux mostly used for brazing processes is borax, which is based on Sodium
Borate powder, mixed with water, to a thin paste before being applied, by brush or
swab, to the site of the joint. Other fluxes are also available where required.

Silver Soldering entails the use of a Copper/Zinc/Silver or Nickel/Silver alloy as


the joining metal and (again depending on the alloy employed), can be done at
temperatures of between 650C to 700C. Brass, copper, monel metal and
stainless steel are typical metals on which silver soldering processes can be
used.

14.5.2 Soft Soldering

Soft Soldering involves the use of a Lead/Tin alloy (with traces of Bismuth and
Antimony added when required) as the filler metal, which melts at temperatures
between approximately 180C to 330C, depending on the composition of the
alloy. The lower temperature requirement, of the soft soldering process, allows
the use of indirect heat.

In earlier times, the heat was provided by the application of an implement with a
wooden handle and a smooth, flat, base or bit (originally made of iron). The iron
was directly heated in a flame, then quickly cleaned, before being applied to the
solder joint, where the transference of its heat would facilitate the melting of the
filler metal. This process possibly needed repeating several times (as the iron
tended to lose its heat fairly quickly) before a large task could be completed.

It was found that copper is a better heat conductor than iron, is less prone to
corrosion and is, therefore, easier to keep clean. Copper, consequently, became
the metal most preferred for use as the soldering bit, though the implement
retained its name of the soldering iron. While needing re-heating less frequently,
it remains necessary to regularly reheat the copper bit of the directly heated
soldering irons.

The advent of electrically heated (and thermostatically controlled) soldering irons


has overcome the re-heating problem, associated with directly heated irons, and
consideration is given here only to the method of soft soldering with the use of
electrically (or indirectly) heated soldering irons.

While the method described is the most commonly used in small workshops (or in
DIY applications), there are, however, three further methods which are used in
industrial applications. Those methods involve:

Applying a naked flame to the joint


Dip soldering
Heating by non-contact techniques.

370280148.doc Issued December 2002 Page 5


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

14.5.3 Using Indirectly Heated (Electric) Soldering Irons

Electric soldering irons are available in a variety of sizes and weights with bits
shaped to suit the particular application. Typically, the 25 watt, electric soldering
iron (refer to Fig. 1), is widely used for making joints in electric circuitry. The
heating element contained in the barrel of the iron is supplied directly from the
mains electrical supply.

Larger, 40 watt (or as large as 125 watt) irons, with proportionately larger bits,
may be used when it is required to create overlapping joints (lap joints) of sheet
metals (though this is a task, not normally done by aircraft maintenance
technicians).

Rubber Grip

Protective Electric
Shroud Power
Lead

Soldering Iron
Body

Copper Bit

Typical 25 Watt Electric Soldering Iron


Fig. 1
Before any soldering operation is attempted, the joint surfaces (and the soldering
iron) must be properly prepared. It is of paramount importance that the joint
surfaces be absolutely free of dirt and grease (and surface oxides), so that the
solder will be able to satisfactorily form intermetallic compounds and, thus, bond
completely with the parent metals.

To ensure this, the approved cleaning methods must be used for the relevant
metals (abrasives, etchants de-greasants etc.) and, finally, an appropriate flux is
applied to the cleaned surfaces, to prevent oxidation at the joint and to assist in
the flow and fusion of the solder.

Note: Some solders have a flux included in their hollow core, while others, require
the application of a separate flux material.

After the surfaces have been carefully prepared, the electric soldering iron can be
switched on and allowed to reach its operating temperature. This is, usually,
indicated by a small, integral warning lamp but may be deduced by applying a
piece of solder to the bit and seeing the solder melt when the temperature is
adequate.

Page 6 370280148.doc Issued December 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

The heated bit of the soldering iron must, next, be tinned. This is achieved by,
firstly, ensuring that the bit is thoroughly cleaned then dipping the bit in flux (if a
separate flux is being used) and applying solder to the bit until a thin film of solder
completely covers the working area of the soldering bit. It is important that the
tinning of the bit is done correctly, otherwise problems will be experienced with
the soldering operation.

Each surface of the prepared joint must also be carefully tinned (refer to Fig. 2) in
a similar manner, so that a thin film of solder covers the total area of the joint
surfaces.

Direction of Soldering

Solder Stick

Copper Bit

B C D E

F G
A

Parent Metal

A oxide film on parent metal


B flux solution above oxidised metal surface
C boiling flux solution removing oxide film
D bare metal in contact with fused flux
E liquid solder
F tin reacting with base metal to form
Inter-metallic compound
G solidifying solder

Tinning the Joint Surface


Fig. 2

370280148.doc Issued December 2002 Page 7


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

Care must be taken, when applying solder to the joint surfaces, to ensure that it is
as thin and as smooth as possible and that the heat is maintained, to allow the
inter-metallic compound between the parent metal and the layer of solder to form.

This compound is an important factor and contributes greatly to the strength of


the joint, as it is, actually, stronger than the solder.

When the two surfaces of the joint are correctly tinned, they are placed together
and the hot iron is applied to an outer surface of the joint. The heat is transmitted
through the metal and melts the solder interfaces so that they fuse together and a
typical soldered lap joint (refer to Fig. 3) of the metals is completed.

Intermetallic
Compound

Solder
Parent Metal

Soldered Lap Joint


Fig. 3

Note: Even when making electrical connections, using soft solder, a type of lap
joint must be made, since an end-to-end joint in wire would be impracticable.

14.5.4 Active and Passive Fluxes

Metal surfaces become more reactive to oxygen when they are heated and, as
previously discussed, to prevent this oxidation, during the soldering process, a
suitable flux is applied to the surfaces being joined.

The flux should possess certain characteristics in that it:

Forms a liquid film over the joint and excludes the gases in the atmosphere
Prevents any further oxidation during the heating cycle
Assists in dissolving the oxide film on the metal surface and the solder
Is displaced from the joint by liquid filler metal.

Page 8 370280148.doc Issued December 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

Fluxes for soft soldering are often classified into two groups, which are the:

Active group: which are corrosive or acid fluxes


Passive group: which are non-corrosive fluxes.

The flux can be applied separately, or as a constituent within the solder. Fluxes
may take the form of a liquid, paste or solid, and the application, for which they
are being used, will govern the type selected.

Active (corrosive) fluxes are used where conditions require a rapidly working and
highly active flux. The common active fluxes are listed below.

WARNING: THESE FLUXES CAN CAUSE BURNS TO FLESH AND CLOTHING.


PROTECT THE EYES WITH GOGGLES AND WEAR RUBBER GLOVES AND
APRON WHEN USING A CORROSIVE FLUX.

Zinc Chloride (ZnCl): commonly called killed spirits. This used on general
sheet-metal work and may be obtained commercially under its trade name of
Bakers Soldering Fluid
Ammonium Chloride (NH4Cl): commonly called sal ammoniac. This used, in
block form, for cleaning the face of the soldering bit before tinning, or in
powdered form, with Zinc Chloride, for tinning cast iron
Hydrochloric Acid (HCI): used in the raw state for pickling the surfaces of the
metal and rendering them clean. As a flux it is extremely active and is suitable
for soldering zinc and galvanised mild steel
Phosphoric Acid: used, primarily, on stainless steels.

Note: Flux residues of acid fluxes remain active after soldering and will cause
corrosion unless removed by thorough cleansing, - first in a weak solution of
caustic soda - and then in water.

Passive (Non-Corrosive) fluxes are divided into three types, which are:

Natural resin: dissolved in suitable organic solvents, it is the closest


approximation to a non-corrosive flux and is particularly suitable for use in the
electrical industry
Tallow: used by plumbers, for the jointing of lead sheet and pipes. Similar to
resin, it is only slightly active when heated to the temperature of the soldering
process
Olive Oil: used for soldering pewter items.

370280148.doc Issued December 2002 Page 9


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

14.5.5 Flux Removal

It is essential that all flux residues be removed, since they can present a
corrosion hazard. The method of removal will be determined by the type of flux
used, but will entail the use of one, or a combination of, the following:

A solution of caustic soda


A solution of sulphuric acid
A supply of warm water
Physical abrasion.

14.6 Inspection and Testing of Soldered Joints

The inspection of soldered joints is done mainly by visual means, though, in some
applications, tensile testing is recommended.

Electrical contacts, using soft soldering methods, may be tested by gently pulling
on the wires to confirm the security of the joint. These joints may also be tested
for electrical continuity and resistance, using appropriate instruments.

14.7 Bonding

Bonding, by the use of adhesives, is the third method of achieving permanent


joints between surfaces, to be considered in this part of the course.

Comprehensive coverage of adhesives and sealants is provided in Module 6 -


(Materials and Hardware), along with details of composite materials, the detection
of typical defects and the methods used in their repair, therefore consideration
here will be limited merely to a summary of:

Bonding terminologies
Methods of bonding
The inspection and testing of bonded joints.

Bonding, in the aerospace industry, is employed to form permanent joints


between materials ranging from composites, fabrics, metals and metal alloys, to
plastics, - all of which are referred to as adherends.

The surface texture of a particular adherend, the type of joint required, and the
manner in which loads are applied to the joint will dictate the type of adhesive to
be used, and the method to be employed, in effecting the joint.

Synthetic resins (and some elastomers) are mainly used as adhesives in the
bonding of aircraft structures and associated components and, while most of
them are used at the manufacturing stages, some may well be used, by aircraft
servicing technicians, during routine maintenance tasks.

Page 10 370280148.doc Issued December 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

WARNING: CONTROLLED VENTILATION, PROTECTIVE CLOTHING, AND


ANTI-FIRE/EXPLOSION PRACTICES, ARE ABSOLUTELY ESSENTIAL, WHEN
WORKING WITH ADHESIVES AND SEALANTS.
ALTHOUGH MANY OF THE ADHESIVES IN CURRENT USE ARE SUPPLIED IN
FILM FORM, SOME ARE LIQUIDS OR PASTES, FROM WHICH, TOXIC AND
FLAMMABLE VAPOURS ARE EMITTED, PRIOR TO CURING.
MANY OF THE NECESSARY, SURFACE PREPARATION SOLVENTS, ALSO
GIVE OFF TOXIC/FLAMMABLE VAPOURS.

The warning is reproduced from Module 6 (Materials and Hardware), where it


also states that the two major groups of adhesives, are:

Flexible adhesives: used where some flexing or slight relative movement, of


the joint is required, and where high load-carrying properties are not
paramount. These adhesives are, generally, based on flexible plastics or
elastomers
Structural adhesives: used in applications where high loads must be carried
without excessive creep and which are relatively rigid without being
excessively hard or brittle. These adhesives are based on resins (commonly
of the epoxy or of the polyester types).

Note: Another group of adhesives is the two-polymer type, which has a


reasonably even balance of resin and elastomer. This results in a flexible, yet
fairly strong, adhesive.

14.8 Methods of Bonding

While the two major groups of adhesives are designated as flexible or structural,
they are further classified as being of the thermoplastic or of the thermosetting
types. Each types characteristics will influence the method employed in its use
as a bonding agent.

14.8.1 Thermoplastic Adhesives

Thermoplastic materials are those which soften on heating and harden when
cooled but will, again soften and harden as often as the heat/cool cycle is
repeated.

Thermoplastic adhesives consist of thermoplastic materials (which may be either


acrylic-, cellulose-, epoxy-, rubber- or vinyl-based), in solution with a volatile
solvent and which may be applied to the surface of adherends in the form of:

Direct application adhesives


Contact (or impact) adhesives.

370280148.doc Issued December 2002 Page 11


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

Direct application adhesives, are spread over the area of both surfaces of the
joint before the joint is closed and the solvent continues to evaporate. This
method can create problems if the joint area is large, as all of the solvent may not
evaporate and a weak joint will result.

Contact adhesives are also applied to both surfaces to be joined but, with these
adhesives, the solvent is allowed to evaporate until the adhesive feels tacky,
when the surfaces are, then, brought into contact and a complete joint is
achieved.

14.8.2 Thermosetting Adhesives

Thermosetting materials (thermosets), once set, cannot be reformed by the


application of heat and they create permanent heat-resisting bonds.

Thermosetting adhesives consist of epoxy- and phenolic-based materials in


addition to polyesters, polyurethanes, and silicones. Thermosets require a curing
process (which is achieved by the application of heat), to cause them to harden.

The heat can be obtained by placing the components being joined into an oven or
into an autoclave (a pressurised oven). Alternatively, the adhesive in the joint can
be heated by the chemical (exothermic) reaction of a hardening agent, which is
added to the adhesive, prior to the joint being made.

Thermosetting adhesives are the types most widely used in the aerospace
industry.

14.9 Inspection and Testing of Bonded Joints

The inspection of bonded joints may be done (as discussed in Module 6) visually,
usually in good lighting conditions and, possibly, with the aid of magnifying
glasses or small microscopes.

Delamination and de-bonding of aircraft honeycomb panels and control surfaces


may be detected by percussion (ring) testing or coin tapping, while more
sophisticated methods, such as ultrasonic and radiographic procedures, may be
used by suitably trained and approved personnel.

Where repairs are done to composite structures, then samples of the adhesives
used are kept for testing, while peel tests are done on adhesives which are used
to attach de-icing or anti-icing elements to the leading edges of propellers or
flying control surfaces.

Page 12 370280148.doc Issued December 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

15 AIRCRAFT MASS AND BALANCE

The main purposes, of monitoring the mass and balance of aircraft, are to
maintain safety and to achieve efficiency in flight. The position of loads such as
passengers, fuel, cargo and equipment will alter the position of the Centre of
Gravity (CG) of the aircraft.

Incorrect loading will affect the aircraft rate of climb, manoeuvrability, ceiling,
speed and fuel consumption. If the CG were too far forward, it would result in a
nose-heavy condition, which could be potentially dangerous on take-off and
landing. If the CG is too far aft, the tail-heavy condition will increase the tendency
of the aircraft to stall and make landing more difficult.

Stability of the aircraft will also be affected with the CG outside the normal
operational limits. Provided the CG lies within specified limits, the aircraft should
be safe to fly. The unit of measurement for mass and balance are normally
dictated by the aircraft manufacturer and can be either Metric or Imperial terms.
Specific definitions for mass and balance ensure they are correctly interpreted.

15.1 Definitions

Datum: The datum is an imaginary vertical plane from which


horizontal measurements are taken. The locations of items such as baggage
compartments, fuel tanks, seats and engines are relevant to the datum. There
is no fixed rule for the location of the datum. The manufacturer will normally
specify the nose of the aircraft, but it could be at the front main bulkhead or
even forward of the aircraft nose

Arm: The horizontal distance from an item or piece of equipment to the


datum. The arm's distance is usually measured in inches (or millimetres) and
may be preceded by a plus (+) or a minus (-) sign. The plus sign indicates that
the distance is aft of the datum and the minus sign indicates distance is
forward of the datum

Moment: The product of a force multiplied by the distance about which the
force acts. In the case of mass and balance, the force is the mass (kg/lb) and
the distance is the arm (m/in). Therefore, a mass of 40 kilograms, at 3 metres
aft of the datum will have a moment of 40 x 3 = 120 kg/m. It is important to
consider whether a value is positive (+ve) or negative (-ve) when moments
are calculated and the following conventions are used:

Distances horizontal: aft of the datum (+), forward of the datum (-).
Weight: added (+), removed (-).

370280148.doc Issued December 2002 Page 1


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

Page 2 370280148.doc Issued December 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

The Dry Operating Mass must be established by weighing or using standard


masses. The influence items included in the Dry Operating Mass and their
position on the aircraft must also be established, as are other mass items such as
the traffic load, fuel load and ballast.

Methods for calculating crew and passenger mass values are laid down in JAR-
OPS and include either weighing the individual crew and their baggage or taking
standard mass values. Whichever method is used must be acceptable to the
relevant Authority.

15.2.1 Mass and Balance Documentation

The Mass and Balance documentation used by an operator must include certain
basic information, which is listed below. Subject to the approval of the authority,
some of this information may be omitted.

A. Aeroplane registration and type


B. Flight identification number and date
C. Identity of the commander
D. Identity of the person who prepared the document
E. Dry operating mass and the corresponding CG of the aeroplane
F. Mass of the fuel at take-off and the mass of trip fuel
G. Mass of consumables other than fuel
H. Load components that include passengers, baggage, freight and ballast
I. Take-off Mass, Landing Mass and Zero Fuel mass.
J. The load distribution
K. Aeroplane CG positions
L. Limiting mass and CG values

Any last minute changes that occur after the mass and balance documentation
has been completed should be brought to the attention of the commander and
entered on the mass and balance documentation. The Operations Manual should
specify the maximum allowable changes to passenger numbers or hold load. If
this is exceeded a new mass and balance documentation should be prepared.

Computerised systems are commonly used to generate the mass and balance
documentation. These systems can only be used once they have gained approval
from the authorities. The integrity of computerised system must be continually
verified by the operator, at intervals not exceeding six months.

Onboard mass and balance and Datalink systems can also be used, but again if
the operator wishes to use these systems as the primary source of mass and
balance documentation, he must obtain approval.

370280148.doc Issued December 2002 Page 3


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

15.3 Frequency of Weighing

Aircraft must be weighed before entering service, to determine the individual


mass and CG position. This should be done once all manufacturing processes
have been completed. The aircraft must also be re-weighed within four years
from the date of manufacture, if individual mass is used, or within nine years from
the date of manufacture, if fleet masses are used.

The mass and CG position of an aircraft must be periodically re-established. The


maximum interval between one aircraft weigh and the next, must be defined by
the operator, but not exceed the four/nine year limits.

In addition the mass and CG position should be re-established either by weighing


or calculation when the cumulative changes in the:

Dry Operating Mass exceed 0.5%


CG position exceeds 0.5% of the MAC.

An aircraft may be transferred from one JAA operator to another without re-
weighing provided both have an approved mass control programme.

15.3.1 Fleet Mass and CG Position

When an operator has a number of aircraft of the same type and configuration, he
may wish to use the average Dry Operating Mass and CG position of this group
of aircraft. The use of fleet mass and CG position is controlled by strict rules to
ensure that all aircraft in the fleet stay within the specified limits. If one aircraft
exceeds these specified limits, it must be removed from the fleet calculations and
individual mass restrictions will apply.

15.4 Weighing Requirements

Weighing of an aircraft can only by done by the manufacturer or an approved


maintenance organisation, and must be done inside a hanger. The aircraft must
be clean and complete, with the correct type of equipment fitted in its proper
position and the required fluids properly accounted for.

The equipment used to weigh an aircraft must be capable of accurately


establishing its mass, and used in accordance with the manufacturers
instructions. Weighing scales should be zeroed before use and calibrated at least
every two years or more often if specified by the either the equipment
manufacturer or the approved maintenance organisation.

Page 4 370280148.doc Issued December 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

15.5 Centre of Gravity Limits (CG Envelope)

The certified CG position of an aircraft will have operating margins built into the
calculations, and is known as the CG envelope. This allows for any movement of
the CG that may be experienced during flight by passengers and crew moving
about the cabin, fuel consumption, landing gear and flaps moving position and
any possible weighing errors or unaccounted modifications.

The operator must show that his procedures account for, the possibility of an
extreme CG variation at any time during the operation of the aircraft.

15.6 Records

All records of weighing, including the calculations involved, must be available to


the authority. The aircraft manufacturer, maintainer or operator must retain
weighing records, and when the aircraft is weighed again, the previous records
must not be destroyed, but must be retained with the aircraft records.

Operators must retain all known weight and CG changes that occur after the
aircraft has been weighed. These records are kept for the life of the aircraft.

15.7 Calculation of Mass and CG of any System

The position of the CG of any system (refer to Fig. 1) may be found using the
following process:

Total Mass is calculated, by adding the mass of each load (plus the mass of
the beam)

The moment of each load is calculated, by multiplying the mass by the arm
(distance from the reference datum)

ALL the moments are added together, to provide the Total Moment

Total Moment is divided by the Total Mass to give CG position.

370280148.doc Issued December 2002 Page 5


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

2.4 m

2.0 m
1.2 m
0.25 m
B
Datum A

Beam Mass 250 kg


Mass A 100 kg Mass B 200 kg

Calculating the Mass and CG of a System


Fig. 1

In the example, shown in Fig. 1, the reference datum is to the left of the beam. A
mass of 100 kg is 0.25 metres from the datum and another mass of 200 kg is 2
metres from the datum. The mass of the beam is 250 kg and the length of the
beam is 2.4 metres.

Using the data, in Table 1, the position of the CG can be calculated thus:

Centre of Gravity position = Total Moment / Total Mass = 725 / 550 = 1.32 m

So the position of the Centre of Gravity is 1.32 metres to the right of the datum.

Table 1
CALCULATION OF POSITION OF CG
ITEM Mass (kg) Arm (m) Moment (Mass x Arm)
Mass 1 100 0.25 25

Mass 2 200 2.0 400

Beam 250 1.2 300

Total 550 725 kg m

Page 6 370280148.doc Issued December 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

15.8 Principles of Weight and Balance of Aircraft

Aircraft mass and balance is concerned with the force produced by the masses
on the aircraft acting at a distance from a specific datum point on the aircraft.

The sum of all moments about any point can be shown to be equal to the moment
of the resultant force about that datum point (refer to Fig. 2). As the entire mass of
the aircraft may be considered to be concentrated at the CG, the total moment of
the aircraft about the datum is the aircraft mass times the horizontal distance
between the CG and the datum.

Arm

Limits

Arm Fwd Aft

Load

Load
Datum

CG (Average Arm)

Mass and Balance Datum, Arms and C.G. Limits


Fig. 2

15.9 Calculation of Mass and CG of Aircraft

The mass and CG position of an aircraft is calculated in much the same way as
that for any system. The Dry Operating Mass of the aircraft corresponds to the
mass of the beam, and is usually found out by weighing the aircraft.

The variable and disposable loads or Traffic Loads, such as fuel, crew,
passengers and cargo correspond to the beam loads. Before each flight, the
mass and moment of these items should be determined so that the aircraft mass
and position of the CG can be determined, prior to flight, to see if they are within
the approved limits.

370280148.doc Issued December 2002 Page 7


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

15.10 Aircraft Weighing Methods

Aircraft weighing equipment consist of weighbridge scales, hydrostatic weighing


units or electrical/electronic strain gauge type weighing equipment. The capacity
of the equipment must be compatible with the load, so that accurate
measurements may be obtained.

All weighing equipment should be calibrated and zeroed before any weighing
commences, with the accuracy of the scale or load cell used depending on its
capacity.

Scale or Load Cell capacity Accuracy

< 2000 kg 1%
2000 kg to 20000 kg 20 kg
> 20000 kg 0.1%

Weighbridge Scales

These consist of a separate weighing platform for each wheel or bogey, the mass
at each reaction point being indicated directly on the balance arm or on a dial
indicator. Large aircraft may be weighed in a hangar, using portable weighbridge
scales, or on weighbridges set permanently into the floor.

Hydrostatic Weighing Units

These are based upon the principle that fluid pressure in a cylinder, in which a
piston is working, depends on the area of the piston and the load applied to it.
The units are placed between the lifting jacks and the aircraft jacking points and
the weight at each position recorded on a gauge.

The gauge may be calibrated directly into weight units or a conversion may be
required to obtain the correct units. It is important that the jacks used with these
units are vertical and the units correctly positioned, otherwise side loads may be
imposed on the units and inaccurate readings obtained

Electrical or Electronic Weighing Equipment

These type incorporate three or more weighing cells, using metallic resistance
elements or strain gauges, the resistance of which varies with change in length,
due to elastic strain. These strain gauges are either incorporated into cells
between the aircraft and the jacks, or they are used in portable weighbridge
platforms placed beneath the aircraft wheels. The output may be measured with a
galvanometer, or sent to an instrumentation unit, which adds all of the platform
values and digitally displays the aircraft load.

Page 8 370280148.doc Issued December 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

15.10.1 Preparation for Weighing

Before weighing the aircraft should be in a condition that meets the requirements
of JAR-OPS. It is recommended that the aircraft be positioned several hours
before weighing, so that an even temperature can be assumed and the aircraft is
free from moisture.

The aircraft should be placed into the Rigging Position, so that consistent results
are obtained and several readings should be taken at each reaction point to
obtain reliable average readings.

Some light aircraft with tail wheels, have a negative load on the tail when in the
rigging position, as a result of the CG being forward of the main wheel centres. In
such instances, it may be possible to use a jack at the nose or a spring balance
may be anchored to the ground and attached to the tail wheel.

The reaction thus obtained will be a negative reaction and its value deducted
from the aircraft weight and treated as a minus quantity when calculating the CG
position.

15.10.2 Weighing on Aircraft Jacks

Jacking should be done in accordance with the Maintenance Manual procedures


and suitable jacking adapters should be placed at the jacking points. Weighing
units of sufficient capacity should be attached to the jacks and the jacks
positioned at each jacking point.

Zero indication of each weighing unit should be verified, before the aircraft is
raised evenly, until clear of the ground when the aircraft should be levelled.
Readings should be made at each weighing point, and to ensure representative
readings are obtained, a second reading should be made.

The Dry Operating Mass of the aircraft may be deduced by adding all of the
readings from each weighing point. With the aircraft weight correctly established,
it remains only to calculate the CG.

370280148.doc Issued December 2002 Page 9


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

15.10.3 Calculation of Aircrafts CG

While the CG of a nose-wheeled aircraft must, obviously, be somewhere near the


main wheels, its location may be found, using the previously described methods.

Taking, as an example (refer to Fig. 3), a nose-wheeled aircraft, which has been
weighed and its Dry Operating ass has been calculated to be 1915 kg. The CG is
forward of the main undercarriage and, using the main wheel centre-line position
as a reference datum, the CG can be found by means of the formula:

AxBC

Where A = Mass at the nose wheel


B = Distance between the front and rear reactions
C = Basic Mass (the sum of all the reactions)

Thus: A x B = 100 x 6 = 600 kg m

and, as C = 1915 kg

then, the CG = 600 (kg m) 1915 (kg) = 0.3133 m or 313.3 mm.

The CG is, therefore, calculated (to 3 significant figures) to be 313 mm forward of


the main wheel centre-line.
Reference
Datum
Nose Wheel
Reaction

910 kg

100 kg
Main Wheel
Reactions

6m 905 kg

Calculation of Aircrafts CG
(Main Wheel Centre-Line as Reference Datum)
Fig. 3

The main wheel centre-line is not, however, always taken as the reference datum
and, as another example (refer to Fig. 4), the reference datum could be taken to
be somewhere between the nose wheel and the main wheel positions.

Page 10 370280148.doc Issued December 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

Nose Wheel
Reaction

910 kg

100 kg
Main Wheel
4m
Reactions

2m 905 kg

Reference
Datum

Calculation of Aircrafts CG
(Reference Datum Aft of Nosewheel)
Fig. 4

In this instance it is necessary to use the formula:

CG = Total Moment Total Mass

It is also necessary to remember that Moments, which are AFT of a reference


datum are considered to be positive or additive (+ve), while Moments, which are
FORWARD of the datum are considered to be negative or subtractive (-ve).

Using the data, displayed in Table 2, enables the aircrafts CG to be calculated.

Table 2
CALCULATION OF AIRCRAFTS CG
Position Mass (kg) Arm (m) Moment (kg m)
Left Main Wheel 905 +4 3620
Right Main Wheel 910 +4 3640
Nose Wheel 100 -2 -200
TOTALS 1915 +7060

Thus Total Moment (+7060 kg m) Total Mass (1915 kg) = +3.687 m (to three
decimal places).

Therefore the CG is located 3.687 metres AFT of the reference datum (which, by
observation, remains at 313 millimetres inches forward of the main wheel centre-
line, as previously calculated).

370280148.doc Issued December 2002 Page 11


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

15.10.4 CG as Percentage Standard Mean Chord (SMC)

Since the position of the CG is an aerodynamic consideration, its position is


sometimes specified as a percentage of the SMC of the wing, measured AFT
from the leading edge (refer to Fig. 5). The percentage SMC may be calculated
using the formula:

(A - B) C x 100

Where A = Distance of the CG from the Reference Datum


B = Distance of the SMC leading edge from the Reference Datum
C = Length of the SMC.

A B x 100 = 8 7 x 100 = 1 x 100 = 22.2%.


C 4.5 4.5

The CG is, therefore, located, 22.2% aft of the leading edge of the SMC.

C = 4.5 m
B=7m

Reference
Datum

A=8m

Calculation of C.G. as a Percentage SMC


Fig. 5

15.11 Changes in Basic Weight

When an item of Basic Equipment is added, removed or re-positioned in an


aircraft, calculations must be made to determine the effect on both Dry Operating
Mass and CG.

In the event of modifications, where the Total Mass and Moment, for additional
parts is not quoted in the appropriate modification leaflet, the additional parts
must be accurately weighed and their moments calculated, relative to the
reference datum.

Page 12 370280148.doc Issued December 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

In order to find the new Dry Operating Mass and Moment of the aircraft, the mass
and moment of the equipment added or removed must be considered as follows:

When equipment has been added, the mass must be added to the original Dry
Operating Mass and, if the arm of the new equipment is +ve (aft of the CG
reference datum), then the moment must be added to the original moment
If the arm is -ve (forward of the CG datum), then the moment must be
subtracted
When equipment has been removed, the mass must be deducted from the
original mass. If the arm is positive the moment must be deducted from the
original moment and vice versa
The revised CG position is calculated by dividing the revised Total Moment by
the revised Dry Operating Mass.

15.11.1 Examples of Alterations to Dry Operating Mass

To consolidate the information, discussed in this topic, the following examples are
provided, and are typical of an aeroplane with a:

Dry Operating Mass of 7000 kg.


CG Reference Datum at Fuselage Station 4000 (i.e. 4000 millimetres aft of
Fuselage Station Zero)
CG located at Station 4600 (i.e. + 600 millimetres aft of the Reference Datum)

Table 3 shows the relevant data when, in the first example, the components of a
Radar System are installed at several locations in the aircraft. The components of
the Radar System (their mass and locations) comprise of a:

Transmitter (mass 13 kg.), at Fuselage Station 4700


Controller (mass 2 kg.), at Fuselage Station 1800
Scanner (mass 9 kg), at Fuselage Station 400

Table 3
Revision to Basic MASS and Moment
Mass (kg) Arm Moment
(m) (kg m)
Original Aircraft 7000 + 0.6 + 4200
Transmitter 13 + 0.7 + 9.1
Controller 2 - 2.8 - 5.6
Scanner 9 - 3.6 - 32.4
Revised Basic Mass and Moment 7024 + 4171.1

370280148.doc Issued December 2002 Page 13


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

With the revised Dry Operating Mass and Moment, the revised CG can be
calculated using the formula:

CG = Total Moment Total Mass

CG = 4171.1 7024

= 0.594 m

The revised Mass and CG Position will, therefore, state:

Dry Operating Mass : 7024 kg.


Centre of Gravity : 594 mm aft of the Reference Datum.

Table 4 shows the relevant data when, in the second example, a Heating Unit
(mass 66 kg.) is removed from Fuselage Station 1600 and re-installed at Station
6000 in the same aircraft as that in the first example.

Table 4
Revision to Basic Weight and Moment
Mass (kg) Arm (m) Moment (kg m)
Original Aircraft 7000 + 0.6 + 4200
Item Removed - 66 - 2.4 + 158.4
Item Replaced + 66 + 2.0 + 132
Revised Basic Mass and Moment 7000 + 4490.4

With the Dry Operating Mass unchanged, the revised CG position will (to two
decimal places), again, be found with the formula:

CG = Total Moment Total Mass

CG = 4490.4 kg. m 7000 kg.

= 0.641.49 m.

In this instance, the revised Mass and CG Position will state:

Dry Operating Mass : 7000 kg.


Centre of Gravity : 641.49 mm aft of the Reference Datum.

Therefore the datum has moved aft by nearly 41.5 mm.

Page 14 370280148.doc Issued December 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

15.12 Loading of Aircraft (Typical Aircraft Load Sheet)

The Captain (or Commander) of an aircraft, must be satisfied that the load,
carried by the aircraft, is of such a weight and is distributed and secured in such a
way that it may be safely carried in flight.

To ensure this, the Traffic Loads must be added to the Dry Operating Mass of the
aircraft and the Total Mass and CG position calculated.

Loading of an aircraft must be completed under the supervision of qualified


personnel, and ensure that the loading of freight is consistent with the data used
to calculate the aircraft mass and balance.

Additional structural limitations such as the maximum load per unit area,
maximum mass per cargo compartment and the maximum seating limits must
also be considered when loading the aircraft.

With large passenger carrying and cargo aircraft, the moment of items such as
fuel, passengers and cargo are considerable and the calculation of CG can be
complicated. In addition to longitudinal CG calculation, it may also be necessary
to distribute fuel and cargo in a transverse direction.

Most operators utilise specialists who deal with loading calculations, and produce
a Load Sheet for each flight. A typical aircraft Load Sheet is reproduced in Table
5.

370280148.doc Issued December 2002 Page 15


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

Table 5
TYPICAL AIRCRAFT LOAD SHEET

Weight (lb) Arm (in) Moment CG


(lb in/1000) (SMC)
Basic Weight 100 000 210 21000.00 29.2
Variable Load
Pilot 165 100 16.50
Navigator 165 100 16.50
Engineer 165 120 19.50
Steward 165 300 49.50
Crew Baggage 100 110 11.00
Passenger Seats 50 Business 450 170 76.50
100 Economy 600 280 168.00
Drinking Water 250 130 32.50
Life-Raft 300 410 123.00
Emergency Transmitter 30 120 3.60
Service Equipment (food etc.) 200 400 80.00
Operating Weight 102 590 211 21 596.60 30.0
Disposable Load
Passengers 1st class (35) 5 775 160 924.00
Tourist (83) 13 695 270 3697.65
Cargo No 1 hold 500 100 50.00
No 2 hold 450 200 90.00
No 3 hold 500 280 140.00
No 4 hold 400 350 140.00
Zero Fuel Weight 123910 215 26638.55 33.3
Fuel Nos 2 and 4 tanks 10000 150 1500.00
Nos 1 and 3 10000 200 2000.00
Reserve tanks 5000 240 1200.00
Take Off Weight 148910 210 31338.55 29.2

Page 16 370280148.doc Issued December 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

370280148.doc Issued March 2002 Page 1


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

Page 2 370280148.doc Issued March 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

The aircraft is normally towed backwards, using a tractor attached to the bridle. It
is normal to tow the aircraft backwards as this reduces the stress on the weaker
nose undercarriage.

If towing points are not available, then ropes may be passed round the legs, as
near to the top as possible, taking care not to foul on adjacent pipes or structure.
A separate tractor should then be connected to each main undercarriage and
steering control achieved by using the steering arm.

16.1.3 Using a Purpose-Made Towing Arm

This is the normal method used on large aircraft. The aircraft is normally towed
with a suitable tractor (or tug) and using the correct, purpose-made towing arm
for the specific aircraft. A person familiar with, and authorised to operate, the
aircraft brake system should be seated in the cockpit (or on the flight deck) to
apply the brakes in an emergency. The brakes should not normally be applied
unless the aircraft is stationary.

The relevant maintenance manual will normally specify details of the towing arm
and any limitations on the towing procedure. On many aircraft with nose-wheel
steering, it is normal practice to disconnect or depressurise the aircraft steering
system before towing.

16.1.4 Precautions when Towing Aircraft

Towing speed should be kept to a safe level at all times (walking pace is a safe
limit).

A steering limit is often imposed, so that the radii of turns are kept within specified
limits, thus minimising tyre scrubbing and reducing the twisting loads on the
undercarriage. It is usual to tow the aircraft forwards in a straight line after
executing a turn, in order to relieve stresses built up in the turn. The steering limit
is often shown by marks painted on the fixed part of the nose leg, but may,
sometimes, be overcome by the disconnection of a pin, joining the torque links.

Suitably briefed personnel should be positioned at the wing tips and tail when
manoeuvring in or around confined spaces, so that obstructions may be avoided.

One person shall be supervising the aircraft movement (NOT the tractor driver)
and should be positioned so that all members of the team can be observed.

Particular care should be given, when towing swept wing aircraft, to "wing tip
growth". This is the tendency of the swept wing to "grow" in a turn and was
discussed in Flight-Line Safety, which is contained in the early topic concerning
Safety Precautions.

370280148.doc Issued March 2002 Page 3


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

Before commencing the towing operation, the brake system should be checked
and the brake accumulator charged as necessary. Brake pressure should be
carefully monitored during the move.

Large, multi-engined aircraft will usually be towed with special-purpose tug and a
suitable towing arm that includes a shear pin, designed to shear if a pre-
determined towing load is exceeded.

In an emergency it may be necessary to move an aircraft from the runway if it has


one or more deflated tyres. Provided there is one sound tyre on the axle the
aircraft may be towed to the maintenance area, but sharp turns must be avoided
and towing speed kept to a minimum.

If there are no sound tyres on an axle, the aircraft should only be moved the
shortest distance in order to clear an active runway and serviceable wheels
should be provided before towing. After any tyre failure, the associated wheel and
other wheels on the same axle should be inspected for signs of damage.

16.1.5 Taxiing Aircraft

When aircraft are to be moved under their own power, whether for ground
movements or prior to flight, a fully certified flight crew must be on the flight deck
and in command of the aircraft. It is usual for the aircraft to have received a daily
inspection before the taxi operation, which ensures items such the oil and fuel
levels and brake pressures are sufficient for the task.

It will be necessary for a Starter Crew to be present before engine starting. This
crew should include a supervisor (who will be in visual and/or verbal
communication with the aircraft crew), a fireman with a suitable extinguisher and
a tractor driver to pull any ground power unit clear after engine starting.

Once the aircraft is moving under its own power, the flight crew has responsibility
for the safety of the aircraft. The ground team should give assistance to the crew,
via the intercom and/or standard marshalling hand signals (refer again to the
Flight-Line Safety section of the earlier Safety Precautions topic), until the flight
crew no longer require their services.

When approaching its parking spot, providing it is not using the automatic parking
indicating system, found on many parking stands, the pilot may be dependent
upon the ground team for clearance indications and stopping cues.

Once stopped, the aircraft wheels must be chocked, given ground power, if
required, and generally taken control of, by the engineers, prior to its next
maintenance procedure.

Page 4 370280148.doc Issued March 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

16.2 Aircraft Jacking

Aircraft may need to be jacked for a variety of purposes. These may include
component changes, retraction tests, weighing of the aircraft and aircraft rigging
checks. Care needs to be taken when jacking, to avoid damage to aircraft or
equipment.

Jacking points are provided in the wings and fuselage, at strong points, to enable
the whole aircraft to be lifted, and there are, usually, other points, at the nose and
main undercarriages, to enable individual wheels to be changed (refer to Fig. 1).

Some aircraft require a jacking pad to be fitted to each jacking point, while in
some, the jacking pads are built into the structure. Special jacking adapters and
beams may be available to lift individual axles.

In all instances, the Maintenance Manual should be consulted, so that the correct
equipment and procedures may be used.

Nose Jacking
Point (Offset)

Main Jacking
Points

Nose Jacking
Point (Offset)

Typical Jacking Points


Fig.1
16.2.1 Special Considerations

Because of the position of the jacking points, the C.G. of some aircraft may be
well behind, or in front of, the main jacking points. It may be necessary to add
ballast forward or rear of the jacking points or to check the fuel load of the aircraft,
to bring the centre of gravity within safe limits as specified in the Maintenance
Manual.

370280148.doc Issued March 2002 Page 5


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

Each jacking point may have a load limit which, if exceeded, could result in
structural damage. To avoid exceeding this limit it may be necessary to install
hydraulic or electric load cells. Any special requirements should be listed in the
Maintenance Manual.

Micro-switches, attached to the undercarriage legs, and operated by the


extension of the shock absorbers (weight-on switches), are used to operate
various electrical circuits, This operation may not be desirable, so circuits should
be isolated, by tripping circuit breakers or removing fuses as necessary.

Aircraft should always be as structurally complete as possible before jacking, It is


essential that any stressed panels which have been removed are re-installed.

Failure to do this may result in distortion or failure of the structure.

16.2.2 Aircraft Jacks

Aircraft jacks are intended for raising and lowering loads and should not be used
for supporting the loads for long periods. Where a load must remain raised for a
long period, it should be supported on blocks or trestles after it has been jacked
to the required height. The most common types of aircraft jacks are the pillar,
trolley, bipod, tripod and the quadrupod hydraulic jacks. There are several sizes
of jacks, with capacities ranging from 4000 kg and greater.

The Pillar hydraulic jack consists of a cylinder assembly, a fluid container and a
hydraulic pump which, when operated, forces fluid from the container into the
cylinder and raises the ram. A release valve is provided which, when opened,
causes the fluid in the cylinder to return to the container and the ram to descend.

Because of possible hydraulic failure, some jacks are provided with a mechanical
locking collar which, when wound down, will prevent the jack from lowering. An
air/filler valve, which vents the return side to atmosphere, may also be provided.
This should always be open when the jack is operated.

Bipod, Tripod and Quadrupod jacks are used, to raise an aircraft for various
servicing operations. Their methods of operation and hydraulic mechanisms are
similar to the pillar jack. They consist of a hydraulic unit, supported by the
relevant number of legs (two, three or four).

Because of the problems involved in raising an aircraft and to avoid injury to


personnel or damage to the aircraft, care should be taken to use the correct type
of jack as stated in the Maintenance Manual. Each jack should be used with the
correct adapter head.

Page 6 370280148.doc Issued March 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

The tripod jack comprises a hydraulic unit with three equally spaced legs. The
jack is designed for a vertical lift only and not for a lift involving lateral movement
of the jack (such as when raising one side of the aircraft for a wheel change). The
resulting side thrust may cause any one of the following:

Serious damage to the ram, due to the bending load


Distortion of the jack legs
Damage to the aircraft, due to the .jack head slipping out of the jacking pad
Shearing of the jacking pad fastener
Dragging sideways of the serviceable tyre.

To change a single wheel, a pillar jack may be used, while two tripod jacks may
be used to raise the complete aircraft (or a bipod jack may be used). The bipod
arrangement overcomes the limitations of the tripod jack for an 'arc' lift. On this
type of jack, two fixed legs provide the support and a third, trailing leg, follows the
lift and steadies the load during the lift. The maximum angle of arc should not be
more than 6.

The quadruped jack is used more commonly as it possesses the advantages of


both types of jack. Two legs are fixed and two are adjustable. This jack may be
used as a bipod jack, by removing the adjustable legs, or as an adjustable, stable
jack with one extra leg added. All four legs may be locked solid, by slight
adjustment of both adjustable legs.

Transportation wheels are often permanently attached to some jacks while they
may be provided as detachable units on other jacks. The wheels facilitate easy
movement of the jacks that would otherwise need to be dragged around the
hangar. Jacks, alternatively, can be dismantled for easier transportation.

16.2.3 Jack Maintenance and General Notes

Aircraft jacks should always be positioned correctly and the load raised and
lowered gradually.

All jacks should be stored in the fully retracted position, kept clean and free from
corrosion. Moving parts should be lubricated regularly and the jack should be
exercised if it is not used frequently.

Jack replenishment is usually through the air valve, up to the level of the bottom
of the air valve. Low oil level is indicated by inability to lift to maximum height,
whilst over-filling is indicated by leakage of oil when the jack is fully extended.

370280148.doc Issued March 2002 Page 7


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

16.2.4 Jacking Precautions

As a safety precaution, small aircraft should normally be jacked inside a hangar.

Larger aircraft may be jacked outside, provided they are positioned nose into
wind; the jacking surface is level and strong enough to support the weight, and
that any special instructions, stated in the Maintenance Manual, are observed.

A maximum wind speed, stated for jacking outside, can also be found within the
Maintenance Manual. The aircraft to be jacked should be chocked fore and aft
and the brakes positioned to OFF (brakes released). If the brakes are
inadvertently left in the ON position (brakes applied) stress could be introduced to
the landing gear or to the aircraft structure, due to weight re-distribution as the
aircraft is raised.

16.2.5 Jacking Procedures

While the following procedures will, generally, ensure safe and satisfactory
jacking of most aircraft, precedence must always be given to the procedures and
precautions specified in the relevant Maintenance Manual.

One person should co-ordinate the operation and one person should control each
jacking point. On larger aircraft a levelling station will also need to be monitored
and all members of the team may need to be in radio or telephone
communication with the co-ordinator.

Checks should be made on the aircraft weight, its fuel state, and centre of gravity,
to ensure they are within the specified limits as detailed in the Maintenance
Manual. The aircraft should be headed into wind (if it is in the open), the main
wheels chocked fore and aft, the brakes released and the undercarriage ground
locks installed.

It is vital that the earth cable be connect to the earth point on the aircraft and it
must be ensured that there is adequate clearance above every part of the aircraft
and that there is clearance for lifting cranes or other equipment, which may be
required.

Jacking pads should be attached to the jacking points and adapters provided for
the jacks as required. Load cells may also be included if needed.

The jacks should be positioned at each jacking point and checks made, to
confirm that the jacks are adjusted correctly (i.e. release valve closed, jack body
vertical, weight evenly distributed about the legs when the adapters are located
centrally in the jacking pads, and the weight of the aircraft is just being taken by
the jacks).

Page 8 370280148.doc Issued March 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

Before jacking commences, the chocks must be removed and then the aircraft
should be raised slowly and as evenly as possible. Whilst jacking is in progress,
the locking collars should be continually wound down, keeping them close to the
body of the jack. When the aircraft is raised to the correct height, the locking
collar should be fully tightened down.

When jacking is complete, then supports may be placed under the wings and
fuselage as indicated in the Maintenance manual.

Note: As previously stated, a pillar (bottle) jack and an adapter are often used for
raising a single undercarriage for changing a single wheel. Alternatively a trolley
jack or stirrup jack may be used. The remaining wheels should be checked to
prevent aircraft movement, and it may be specified that a tail support be located
when raising a nose undercarriage. The jack should be raised only enough to lift
the unserviceable wheel clear of the ground.

16.2.6 Trestles

These are provided to support to aircraft structures (main planes, fuselages etc.)
and may also be used to support the complete aircraft. Various types are
available including plain wooden trestles that are purpose-built and not
adjustable. Trestles should only be used at designated strong parts of the
structure. It will normally be shown in the Maintenance Manual where they should
be positioned. Lines are often painted on the aircraft to show where the trestle
beam is positioned

The Universal trestle is made up from lengths of angle iron, bolts and nuts, and
has two jacking heads. By using different lengths of angle iron, trestles of various
sizes can be produced. The wooden beam across the jacking heads may be
replaced by a wooden former, which is cut to the curvature of the component it
supports.

Padding is normally attached to the former, to prevent damage to the aircraft


finish. The two jacking heads, which are hand-operated screw jacks, enable the
beam to be adjusted to suit the angle of the component.

Although the trestles have jacking heads, they should only be used for
supporting a load, and not for attempting to raise parts of the aircraft. Damage
may be caused to the aircraft if attempts are made to do any more than support
the structure.

The Tail trestle is not suitable for heavy loads and must only be used for
supporting a load vertically. Adjustment in height is made by a screw thread. In
the same manner as a universal trestle, the beam can be made in the same
shape as the contour of the aircraft.

370280148.doc Issued March 2002 Page 9


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

16.2.7 Lowering Aircraft off Jacks

Before lowering the aircraft to the ground, all equipment, trestles, work stands
etc. should be moved clear of the aircraft, to prevent collision or contact with the
aircraft structure. The wheels should be rotated by hand, to ensure the brakes are
off. The jacks should be lowered together, by opening their respective release
valves, and the locking collars (if used) unscrewed (but kept close to the jack
body), whilst the jacks are lowered. The jacks should be fully lowered after the
aircraft is resting on its wheels and the release valves then closed.

On no account should the top of the jacks be handled until the jack is clear of the
aircraft. It is common for the aircraft shock absorbers to stick and to suddenly
collapse, resulting in damage to equipment or serious injury to parts that might be
between the aircraft and jack.

After the aircraft is lowered and the jacks removed, the jacking pads and adapters
should be removed and the chocks placed in position.

Any fuses or circuit breakers should be re-set in their correct position.

16.3 Slinging

Slings may be required for lifting various parts of an aircraft during maintenance,
repair, dismantling and assembly. Sometimes a complete aircraft may need to be
lifted for transportation or to clear a runway quickly.

The use of the correct equipment for lifting aircraft parts will minimise the risk of
damage to the aircraft and personnel. A list of special equipment is usually in the
front of the Maintenance Manual. This list will usually include special slings to be
used on the aircraft and any other special equipment or tools required.

Slings may be of the three-point type, as used for lifting-main planes, while other
types, used for lifting engines, fuselages or other large items may be provided
with spreader bars or struts.

Before removing a main plane, the opposite main plane must be supported with
trestles. To attach a sling, some aircraft have special slinging points with threaded
holes in the airframe, which are used to accommodate the eye or fork-end bolts
of the sling. These holes are normally sealed, with removable plugs, when not in
use. As an alternative to screw-in devices, some slings are used in conjunction
with strong straps that pass under the component to be lifted.

Page 10 370280148.doc Issued March 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

16.3.1 Lifting Tackle

The following is a list of safety precautions that must be used when using lifting
tackle:

Do not exceed the safe working load of the lifting devices


Do not leave a suspended load unattended at any time
Do not walk or work under a suspended load
Do not tow the hoist at greater than walking pace
Do not tow the hoist, other than by hand, when a load is suspended from the
lifting hook
Do not allow the load to swing, especially when it is being hand-towed
Do not using a hoist or crane on soft ground
Do not use a crane or hoist if the lifting tackle shows signs of damage.

Wire rope, chain or fibre rope may be used for lifting purposes. Before use, the
tackle should be inspected to ensure that it is serviceable, is of the correct type
and, when used, that the Safe Working Load (SWL) is not exceeded. The SWL
should be stated on an identification plate, attached to the lifting sling, and should
never be removed from the sling.

Wire Rope is used with cranes, hoists, gantries and various slings. Before use,
the wire rope, splices and attachments should be inspected for damage such as
wear, corrosion and broken wires.

In use, care should be taken that the rope does not kink under load. Before
multiple leg wire rope slings are used, they should be laid out on the floor to
ensure shackles are correctly attached and the fittings are not twisted. Knotting of
ropes, to shorten them, is prohibited.

Wire rope slings may be treated against corrosion by immersion in oil and the
surplus oil wiped off, but this treatment must not be applied to slings used for
oxygen cylinders. They must always be free from oil or grease.

Chains are used with cranes and various types of sling. Before use, all chains
must be inspected for damage such as cracks, distortion, excessive wear and
socketing.

Socketing is the name given to the grooves, produced in the ends of links, when
the links wear against each other. Any reduction in diameter will render the chain
unserviceable.

Fibre rope slings may be used for lifting lighter components, and are made from
natural fibres such as sisal, hemp or nylon fibres. They must be inspected for
frayed strands, pulled splices, excessive wear and deterioration.

370280148.doc Issued March 2002 Page 11


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

When not in use, fibre rope slings should be hung on pegs, in a sheltered
position, and free from dampness. Immediately before use, the rope should be
opened up, by slightly untwisting the strands, to ensure they are not damaged or
mildewed internally.

A damaged or mildewed fibre rope sling should not be used, and it must be
destroyed, by cutting into small, unusable sections, before final disposal.

In addition to before-use checks on the rope, all loaded components such as


pulley blocks, shackles, pins, spreader bars and hooks are to be inspected for
excessive wear, cracks and flaws. Moving parts must be lubricated periodically.

16.4 Parking and Mooring Aircraft

When an aircraft is out of service and in the open it should be secured against
inadvertent movement and protected against adverse weather conditions. The
operations recommended in the relevant Maintenance Manual depend on the
type of aircraft, the length of time it will be out of service and the prevailing or
forecast weather conditions.

16.4.1 Parking

Between flights it is usually sufficient to apply the parking brakes, lock the control
surfaces and chock the wheels but, in a strong wind, light aircraft should be
headed into the wind. Light aircraft without wheel brakes should be headed into
wind and their wheels chocked front and rear.

Flying controls, on many aircraft, are locked by movement of a lever in the


cockpit/cabin. The lever is connected to locking pins at convenient positions in
the control runs or at the control surfaces. When this type of control lock is not
provided, locking attachments may have to be fitted to the control column and
rudder pedals.

A more positive method entails the use of external control surface locks, that
prevent control surface movement and, thus, prevent strain on the control
system. All external locks should have suitable streamers attached, to make them
more visible.

If an aircraft is to be parked overnight or for longer periods in the open, then


additional precautions should be taken, to guard against the effects of adverse
weather.

The undercarriage ground locks should be fitted, and all openings, such as static
vents, engine and cooling air intakes, should be blanked, to prevent ingress of
dirt, birds, insects and moisture. Items such as pitot head and incidence
indicators should also be covered.

Page 12 370280148.doc Issued March 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

When severe weather is anticipated it is recommended that covers for cockpit,


canopy and wheel are fitted if available. Blanks and covers should not be left in
position when the aircraft is prepared for service. Servicing instructions should
include a pre-flight check to ensure that all covers etc, are removed.

16.4.2 Mooring (Picketing)

In certain weather conditions, particular in high winds, it would be recommended


that the aircraft be parked in a hangar. If they must be left outside, then smaller
aircraft may need to be tied down. The aircraft may be provided with picketing
rings or attachment points at the wings and tail or adjacent to the undercarriage
legs (refer to Fig. 2).

B C
A

View A

View B View C

Aircraft Picketing Points


Fig. 2

370280148.doc Issued March 2002 Page 13


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

If outside, the aircraft should always be parked nose into wind and secured, from
the picketing points to suitable ground anchor points such as heavy concrete
blocks or specialised screw pickets.

Cable or nylon rope of adequate strength should be used where possible but, if a
natural fibre rope is used (sisal or hemp), then sufficient slack must be left to
allow for shrinkage in damp conditions.

Additional picketing from the undercarriage legs may be recommended in strong


winds and, if so, care should be taken not to damage any pipelines or equipment
attached to the legs or wheels.

16.4.3 Typical Small Aircraft Procedures

When mooring small aircraft in the open, the aircraft, if possible, should be
parked head into the wind. The control surfaces should be secured with the
internal control lock and the brakes applied.

Care must, however, be exercised in extremely cold weather and parking brakes
must not be set if there is a danger that accumulated moisture may freeze the
brakes. Another danger, in cold weather, exists when the brakes are overheated,
because, if they are set in this condition, serious distortion and cracking of the
brake (and wheel) components can occur as they cool down.

Ropes, cables, or chains should be attached to the wing mooring (tie-down)


points, and their opposite ends secured to ground anchors. A tie down rope (no
chains or cables) should be fastened to the exposed portion of the engine mount
and the opposite end of the rope also secured to a ground anchor.

The middle of a rope should be attached to the tail tie-down ring and each end of
the rope pulled, at a 45 angle, and secured to a ground tie-down point either side
of the tail.

A control lock should be applied to the pilots control column. If a control lock is
not available, then the control may be tied back with a front seat belt.

These aircraft are usually equipped with a spring-loaded steering system that
affords protection against normal wind gusts. However, if extremely high winds
are anticipated, additional external locks may be installed.

16.4.4 Large Aircraft Procedures

These may only require picketing in very strong wind conditions. The maximum
wind-speed will normally be stated in the Maintenance Manual (including gusting
winds). The aircraft should be headed into wind and the parking brakes applied.

Page 14 370280148.doc Issued March 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

Cables or chains should be attached from the aircraft picketing points to prepared
anchorages. In some instances the picketing cables are special components and
include a tension meter that is used to apply a pre-load to the cable.

If an aircraft is to be parked for a longer period, then additional precautions must


be taken. Landing gear down-locks must be installed (if so equipped) and all
openings such as static vents and engine intakes should be covered or blanked
off (refer to Fig. 3) to prevent the ingress of dirt, birds, insects and all forms of
precipitation.

Intake Blank

Pitot-Static Blanks

Exhaust Blank
Nose Wheel Covers Main Wheel Covers

Typical Aircraft Blanks


Fig. 3

16.4.5 Chocking of Aircraft

When aircraft are parked, it is normal to place a chock ahead and behind at least
one wheel set. The parking brakes are usually left in the off position once chocks
are in position, to allow the heat, generated by the brakes, to dissipate evenly.

At high wind speeds, it is normal to chock all the wheels and apply the brakes (if
they have cooled). Some aircraft chocks can be chained together, to give a more
secure hold. During ground runs (and especially those involving high power), it is
common sense to place chocks at the front of all main wheel sets, to reinforce the
parking brake.

370280148.doc Issued March 2002 Page 15


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

16.5 Aircraft Storage

If an aircraft is de-activated for an extended time it will need to be protected


against corrosion, deterioration and environmental conditions during its period of
storage.

The following notes are based on the storage procedures applicable to BAe 146
aircraft that have been de-activated for periods in excess of 30 days and up to a
maximum of 2 years. It is not intended for the information given here to be
complete, but merely to give the student examples of some of the activities
performed. Specific details of an aircrafts storage procedures can be found in
Chapter 10 of the relevant Maintenance Manual.

A list of equipment and materials is normally given. This will, typically, include:

Hydraulic fluid and lubricating oils and greases


Specialised water-displacing fluids and corrosion-preventative compounds
Aircraft covers and blanks
Plastic sheeting and adhesive tape.

Prior to the storage period certain tasks are completed. These may include
replacing the tyres with dummy tyres (those not suitable for flight), or the raising
of the pressures of the normal ones. The various tanks are either filled (water),
drained (toilet), or part-filled (fuel). If the aircraft has propellers, they must be
feathered, to prevent them rotating in the wind. (they may also be restrained by
straps).

Generally there would be an initial procedure, this being repeated at specified


intervals, as shown in Tables 1 (a) and 1 (b). If no repeat interval is given, then
the item is only done initially.

Once the aircraft has been prepared, there are routine, weekly checks to keep it
in good condition.

Page 16 370280148.doc Issued March 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

Table 1 (a)
TYPICAL AIRCRAFT STORAGE TASKS
ITEM Repeat Intervals
(days)
Landing Gear
Clean and dry main and landing gear bays
Check landing gear for hydraulic leakage 7
Lubricate main & nose landing gear
Clean/Check Shock struts for leaks. Wipe sliding tube with hydraulic fluid 30
Clean Gear & Door Uplock Mechanisms. Protect with grease 60
Clean and apply thin coat of hydraulic fluid to actuator and piston rods
Spray micro-switches and proximity switches with water dispersion fluid
Check tyre pressures and mark position of tyres with date 7
Rotate wheels one quarter of a term and mark tyre with date 15
Should aircraft be stored in a hangar, deflate the shock absorbers. The aircraft
may be manoeuvred in the hangar with deflated shock absorbers

Flight Controls
Fully extend flaps 7
Open and tag flap valves and airbrake circuit breakers
Fully extend lift spoilers and install safety sleeves to all spoiler jacks 7
Depressurise hydraulic system 7
Lubricate the flight controls 30
Protect flap carriages, upper surfaces of flap tracks with grease
Protect all control cables accessible with oil 30
Check for corrosion and where found repair affected areas 90
Power Plants
Carry out special long term storage procedure for engines 180
Note: Renewal of engine long term storage is preceded by engine run

Oxygen System
Check test date of oxygen cylinders.
Disconnect distribution lines from oxygen cylinders, blank off pipelines and
cylinder outlet connection
Check cylinder pressure is above 50 p.s.i.
Remove crew masks for storage

370280148.doc Issued March 2002 Page 17


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

Table 1 (b)
TYPICAL AIRCRAFT STORAGE TASKS
ITEM Repeat Intervals
(days)
Water Waste
Drain potable water system
Purge potable water system with dry air or nitrogen

Fuel System
Refuel aircraft with fuel treated with an approved biocidal agent
Check fuel tanks for water accumulation 7

Air Conditioning System


Install blanks in the ECS ram air inlet, exhaust, APU intake, APU oil cooler, front 7
and rear discharge valves

Hydraulic System
Check system for leaks 7
Replenish system 180
Coat all unpainted hydraulic pipe-work with preservative compound

Aircraft Exterior
Wash aircraft
Coat all unpainted metal surfaces with preservative compound

Aircraft Interior
Remove passenger seats and carpets for bay storage
Remove, service and store all galley portable equipment
Remove, check and store windshield wiper arms complete with blades
Remove rain repellent cannisters

Electrical/Electronic System
Remove and service batteries 7
Remove for bay service, all rack mounted electronic equipment
Apply power to and function installed electronic equipment 7

Page 18 370280148.doc Issued March 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

To allow the circulation of air around the inside of the aircraft, all the doors and
curtains are fixed open, whilst all the external doors and panels are shut. The
battery will be removed from the aircraft and kept in the battery bay.

More active checks might be done on the two-weekly checks. These checks will
probably involve re-installing the battery, running the engines for a period and
functionally testing a number of the aircrafts systems that require the engines
operating. The flight controls might require cycling throughout their ranges and, if
dummy tyres are not fitted, the aircraft must be moved slightly to prevent flat
spots forming on the tyres.

In addition, when power plants are stored separately, their fuel and oil systems
must be inhibited and all their external mechanisms protected with grease or
other suitable preservative. They must be stored in a clean, warm, dry
atmosphere with inspections at intervals to check for deterioration. Some engines
are stored in an airtight bag, which has moisture-absorbent crystals (a desiccant)
inside.

After the storage period all of the covers, blanks and preservative compounds will
need to be removed. All of the systems will need to be restored to their original
condition prior to aircraft use. A further set of procedures will be followed, similar
to those previously discussed.

When the aircraft is to be returned to service, it is simply a case of initially


removing all covers, blanks and tie-downs. Once access to the inside of the
aircraft is obtained and the battery re-installed, all of the systems must be
checked and tested.

All the tanks must be replenished to their correct levels and all pressure vessels
will require their gases charging to their normal operating pressures. If the cabin
furnishings, such as seats, carpets and galleys have been removed, they are to
be inspected and, when serviceable, re-installed in the cabin.

As already stated, the foregoing summaries are only examples of the form that a
basic aircraft storage procedure might take. If the aircraft is smaller or larger and
more complex it will require a different form of inspection and routine checking.

The correct storage procedures will be found in Chapter 10 of the relevant


aircrafts Maintenance Manual.

370280148.doc Issued March 2002 Page 19


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

16.6 Aircraft Fuelling Procedures

The use of the term fuelling can include both refuelling and defuelling
procedures and these notes contain examples of the essential points to be
considered when refuelling and defuelling aircraft.

There may, however, be some further, local instructions, regarding the


responsibilities of the various personnel involved in fuelling procedures and these
will always take precedence in conjunction with the relevant Maintenance
Manual.

16.6.1 Fuelling Safety Precautions

Particular care must be taken when fuelling aircraft, so that the operation may be
accomplished in the safest possible manner.

Whenever possible, aircraft should be fuelled in the open, and not in a hangar
(although this is, sometimes, necessary as part of a maintenance programme).
This will minimise the fire risk from high concentrations of flammable vapours.

Fire appliances should be readily available during all fuelling operations. Carbon
dioxide, or foam, extinguishers are recommended but, if there is a perceived
increased fire risk, then fire-fighting vehicles should be standing by.

Within the specified danger area, around an aircraft being fuelled, no sources of
ignition or sparks should be allowed and no electrical power should be switched
on or off during the fuelling operation.

It is vital that the correct type and grade of fuel is used for the fuelling operation.
Use of a turbine fuel in a piston aircraft will certainly cause an engine malfunction,
or failure, that could lead to loss of an aircraft. The correct type and grade of fuel
is always detailed in the Maintenance Manual and marked adjacent to the
aircrafts fuelling point(s).

Care should also be exercised so as to avoid contamination of the fuel system


with water or other contaminants. The fuel supply should be regularly checked for
water contamination and a sample of fuel drained off after refuelling, so that a
water check may be done.

It will sometimes be necessary to filter the fuel during over-wing refuelling,


particularly in dusty climates.

Page 20 370280148.doc Issued March 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

Electrical bonding of the fuel system is vital during fuelling operations, as when
fuel flows through the refuelling hose, static electricity may be generated. This
may lead to potential differences at adjacent metal parts and initiate a spark, fire
or explosion. To minimise this risk the following actions should be completed
before fuelling operations commence

The aircraft should be earthed


The refuelling tanker should be earthed
The nozzle of the fuel hose should be electrically bonded to the fuelling point.

16.6.2 Refuelling

When refuelling the AMM should always be consulted so that the positions and
capacities of the fuel tanks and also the type of fuel, position of the refuelling
point(s) and refuelling procedures are known. There are two general re-fuelling
methods:

Gravity or over-wing refuelling: which is, essentially, the same method as used
to refuel a motor car (automobile), with a similar type of refuelling hose being
used. As the name suggests, the filler points are, generally, on the upper
surface of the wing and the tank is open when refuelling is done

Pressure refuelling: in which the fuel may be pumped into the aircraft via a
pressure refuelling coupling at very high rates. The refuelling pressures and
the rates of fuel delivery may be quite different for individual aircraft types, so
great care must be taken, to ensure no damage occurs to an aircraft through
incorrect refuelling settings.

16.6.3 Checking Fuel Contents

This is normally done, using the aircraft fuel gauges, which may be calibrated in
kilograms (kg), gallons (Imperial or US) or pounds (lb).

If a double check is required, then the contents may be determined, on the


ground, by using dip sticks (installed into the top of the tanks) or by drip sticks
(or magnetic drop sticks) which are installed in the bottom of some aircraft tanks.

The aircraft fuel gauges will normally be positioned on the flight deck, but they
can, on some aircraft, be duplicated at a fuelling panel, adjacent to the pressure
refuel coupling.

370280148.doc Issued March 2002 Page 21


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

The Relative Density (RD) of fuel will vary with temperature and so the weight of
a certain quantity of fuel will also vary.

For example, ten gallons (Imperial) of fuel, with an RD of 0.8, will have a weight
of 80 lb, while ten gallons (Imperial) of fuel, with an RD of 0.78, will weigh 78 lb.

It is crucial, for balance purposes, that the weight of fuel is known and this is the
reason why many aircraft fuel gauges are calibrated in units of weight rather than
in volume.

When fuelling aircraft, it is essential that the technician is aware of the RD of the
fuel, so that the necessary weight calculation may be done, if necessary.

16.6.4 Defuelling.

Occasionally, it is necessary to remove fuel from an aircraft, to facilitate fuel tank


maintenance, or because the aircraft is too heavily loaded for the next flight.

Removing fuel from an aircraft can be accomplished by either the gravity or by


the pressure defuelling method.

The gravity method entails draining the fuel into a suitably earthed container, and
this is typical of light aircraft, which are normally gravity refuelled. The fuel
removed must be disposed of in the correct manner, with regard to local
instructions and to the environment.

Aircraft that are normally pressure refuelled are normally equipped with a
pressure defuelling facility. Pressure defuelling is achieved by utilising a small
negative pressure (suction), which effectively draws the fuel out of the tank and
returns it into the fuel tanker (bowser).

Current rules will normally only allow the fuel, removed from an aircraft, to be
placed into a dedicated defueller vehicle and the fuel will not be permitted to be
used in another aircraft. This ensures that any contamination such as water or
debris will not be transferred to other aircraft.

Page 22 370280148.doc Issued March 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

16.7 Ground De-Icing/Anti-Icing of Aircraft

16.7.1 Ice Types

There are three main types of ice/frost that can effect an aircrafts performance,
Hoar Frost, Rime Ice and Glaze Ice. The temperature and weather conditions will
determine the type of ice that forms, but all three types can have a detrimental
effect.

The Dew Point is the temperature at which moist air becomes saturated and
deposits dew if in contact with a colder surface or the ground. Above ground,
condensation into water droplets takes place.

Hoar Frost is a deposit of ice crystals that form on an object when the dew point
is below freezing point. High humidity will normally produce hoar frost, as these
are similar to conditions that produce dew. Hoar frost can form when the air
temperature is greater than 0C, but the aircraft skin temperature is less than
0C. This type of frost produces a very rough surface which leads to turbulent
airflow.

Rime Ice is a light coloured opaque rough deposit that has a porous quality. At
ground level it forms in freezing fog from water droplets with very little spreading.
It adds very little weight but it can disrupt the smooth flow of air over the wing,
and block pitot and static vents.

Glaze Ice can be either transparent or opaque and can form into a glassy surface
due to liquid water flowing over a surface before freezing. It is the most
dangerous type of ice found on an aircraft and is dense, heavy and tough. It
adheres firmly to a surface, is difficult to shake off, and if it does breakaway, it
does so in large chunks.

During cold weather operations, it may be necessary to remove ice and snow
from the aircraft, while it is on the ground, and to keep it clear long enough, to
allow the aircrafts systems to cope with snow or ice removal. This may not occur
until the aircraft is flying.

370280148.doc Issued March 2002 Page 23


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

On the ground, the aircraft must be cleared of all snow and ice from its wings, tail,
control surfaces, engine inlets and other critical areas (refer to Fig. 4) before the
aircraft can take-off.

Rudder

VHF Ailerons
Antenna

TCAS Elevator
Antenna

Flaps
Pitot and
Static
Heads

Slats
Engine Nacelle

Critical Surfaces for De-icing and Anti-icing


Fig. 4

Ice formation on an aircraft on the ground may result from a number of causes:

Direct precipitation from rain, snow and frost


Condensation freezing on external surfaces of integral tanks following
prolonged flight at high altitude
After taxing through snow or slush, ice may accumulate on landing gear,
forward facing surfaces and under-surfaces.

Page 24 370280148.doc Issued March 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

The formation of ice on aircraft structures can produce many adverse effects, and
if allowed to remain may result in some or all of the following:

Decreased aerofoil lift


Increased aerofoil drag
Increased weight
Decreased engine thrust
Freezing of moisture in control hinges
Freezing of micro-switches that affect systems such as the landing gear
retraction
Ingestion of ice into the engine.

16.7.2 Definitions

The terms de-icing and anti-icing have specific definitions, and it is essential to
know the differences.

De-icing is the removal of ice that has already formed


Anti-icing is the prevention of initial ice formation.

16.7.3 De-Icing and Anti-Icing Methods

The de-icing procedure for removal of ice, frost and snow from an aircrafts
surface can be achieved by mechanical or chemical methods. Mechanical
methods use blowers, brushes and rubber scrapers whilst chemical methods
utilise de-icing fluids.

The anti-icing procedure provides protection against the formation of ice, frost
and snow on aircraft surfaces for a short period known as the Holdover Time.
This is achieved by applying an anti-icing fluid, but the aircraft must be either
clean or de-iced prior to this anti-icing fluid application. There are two ways of
aircraft de-icing and anti-icing:

One Step Method


Two Step Method.

370280148.doc Issued March 2002 Page 25


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

The One Step method utilises hot fluid to de-ice the aircraft, and this fluid remains
on the aircraft surfaces to give a limited anti-icing capability.

The Two Step method consists of two separate fluid application procedures. The
first step is the de-icing part and the second step the anti-icing. This second step
must be done within three minutes of starting the first step, surface by surface if
necessary. The second anti-icing step protects the aircraft surfaces for a holdover
period.

Whilst the AMM will detail the exact areas for de-icing and anti-icing, particular
attention should be paid to areas around probes, antennas, and pitot/static ports
as well as control surfaces, landing gear and inlets and exhausts.

16.7.4 Chemical De-Icing

Freezing Point Depressant (FPD) compounds are often used in conjunction with
mechanical methods, and there are two main types of FPD compounds:

Type 1 (unthickened)

These fluids have a high glycol content and a low viscosity. They provide good
de-icing performance but only a limited protection against re-freezing.

Type 2 (thickened)

These fluids have a minimum glycol content of approximately 50%, and due to a
thickening agent, are able to remain on the aircraft surfaces for longer periods.
The de-icing performance is good and provides protection against re-freezing
and/or build up of further accretion, when exposed to freezing precipitation.

16.7.5 Treatment of Frost Deposits

Frost deposits are best removed by the use of a de-icing fluid such as Kilfrost
ABC (Aircraft Barrier Compound). These fluids usually contain either:

ethylene glycol and isopropyl alcohol


di-ethylene glycol and isopropyl alcohol
propylene glycol and isopropyl alcohol.

This process is not lengthy and one application is usually sufficient provided it is
applied within two hours of flight. Only fluids recommended by the manufacturer
should be used and any instructions for their use should be strictly observed. Use
of incorrect de-icing fluids may adversely affect glazed panels or paint finish.

Page 26 370280148.doc Issued March 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

Alcohol based de-icing fluids, may cause dilution or complete removal of oils and
greases from joints or bearings. This may allow water ingress, which can
subsequently freeze and jam controls. De-icing spray nozzles should not be
directed at lubrication points or sealed bearings.

Hot air blowers may be used to remove snow, ice or frost, and the liquid residue
should be dried and not allowed to accumulate in places such as hinges or micro-
switches as any re-freezing may cause damage.

16.7.6 Removal of Ice and Snow Deposits

There are several methods of removing snow and ice from an aircraft, prior to
applying liquids if required.

Removal by hand can be accomplished by the use of soft brooms, hand brushes
or rubber scrapers. The aircraft can be de-iced using cold air from a pressure
supply unit, or by using hot air from a hot air blower designed for the purpose.

Deep wet snow should be removed with a brush or rubber scraper, taking care
not to damage components such as aerials and pitot probes, which may be
covered in snow. The snow should also be cleared from items like vents and
control hinges.

Light dry snow should be blown off using a cold air blower. Hot air is not
recommended as it may melt the snow which may accumulate and freeze
requiring further treatment.

Moderate to heavy ice deposits or residual snow should be cleared with de-icing
fluid applied by spraying. The two methods of fluid spraying involve the:

Cold Fluid Spray


Hot Fluid Spray.

When using these sprays, it is necessary to observe certain precautions, because


of the risk of damage to the aircraft structure and associated components. With
this in mind it is important to know that:

High-pressure sprays may cause damage to pitot-static probes and other


sensing devices
Covers and bungs should be fitted during de-icing operations to prevent
ingress of fluid into intakes and exhausts
High-pressure sprays may cause erosion of the aircraft skin. Consult the AMM
for recommended maximum impingement pressure
No attempt should be made to remove ice by using an impact force to break
the bond

370280148.doc Issued March 2002 Page 27


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

De-icing should proceed symmetrically, to prevent excess weight on one side


of the aircraft.

The Cold Fluid Spray method is the simplest method of applying de-icing fluid,
but in severe conditions one application may not be sufficient to remove all
deposits. Brushing followed by a second or third application may be required.

The Hot Fluid Spray method has been adopted specifically to reduce turn-round
time. The FPD fluid is mixed with water in proportion to suit prevailing weather
conditions, and heated to between of 60C (minimum) and 85C (maximum).

The fluid is normally sprayed onto the aircraft at a pressure of 100 psi (689.5
kN/m2) by use of spray lances. The nozzle of the lance is held close to the aircraft
skin, to prevent heat losses.

The heat transfers to the skin of the aircraft, breaking the ice bond, and large
areas of ice may be flushed away by turning the nozzle sideways. The fluid film
remaining on the skin, has only been slightly diluted beyond its original dilution
and is effective in preventing further ice formation.

Hot water de-icing is a method that must not be used below -70C and may need
to be performed in two steps.

Step 1: Snow and ice are normally removed initially with a jet of hot water not
exceeding 95C
Step 2: If necessary a light coating of de-icing fluid is then sprayed on
immediately (within 3 minutes) to prevent re-freezing.

On some aircraft, not equipped with aerofoil or propeller de-icing systems, the
use of a de-icing paste may be specified. The paste is spread evenly, by hand,
over wing, tail and propeller leading edges. It provides a chemically active surface
on which ice may form but not produce a bond. Any ice, which forms, is blown
away by the airflow. The paste should be re-applied before each flight in
accordance with the AMM.

Page 28 370280148.doc Issued March 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

16.7.7 Hold Over Times

When used for anti-icing, the FPD fluid should be sprayed onto the aircraft cold
and undiluted, before the onset of icing or after any hot de-icing. The fluid film will
prevent ice and snow from sticking to the aircraft skin and, given time, will melt
any fresh precipitation. Typical times for which the fluid remains effective are
known as the Hold Over time (refer Table 2).

Table 2
TYPICAL HOLD OVER TIMES

Ambient Weather Conditions Type II (AEA) fluids Type I


Temp C Frost Freezing Steady Freezing Rain on Anti- De-Icing Fluids
fog Snow Rain cold Icing (See note 2)
soaked 100% 75/25 60/40 50/50
wing Cold (hot) (hot) (hot)
See
Note 1
Above 0 * 8 hrs 5 hrs 4 hrs 3 hr 45 min
* 3 hrs 2 hrs 1 hr 1 hr 30 min
* * 1 hr 45 min 35 min 30 min 15 min
* 20 min 10 min 7 min 5 min 5 min

0 to 7 * 8 hr 5 hr 4 hr 3 hr 30 mins
* 1 hr 1 hr 50 min 45 min 15 mins
* 45 min 30 min 20 min 15 min 15 mins
* 20 min 10 min 5 min 3 min 3 mins

-8 to * 8 hr 5 hr 4 hr 30 mins
-10 * 1 hr 1 hr 50 min 15 mins
* 45 min 30 min 20 min 15 mins

-11 to * 8 hr 5 hr 30 mins
-14 * 1 hr 1 hr 15 mins
* 45 min 30 min 15 mins

-15 to * 8 hr 30 mins
-25 * 1 hr 15 mins
* 45 min 15 min

Under extreme cold conditions it may be necessary to heat the fluid (60C max)
to give it sprayability. No significant increase in hold over time is achieved by
strengthening the mix of type I (AEA) fluids.

Stations using Kilfrost will normally provide a mix of 50/50 or 60/40. It may be
difficult to get stronger mixes at short notice unless the temperature conditions at
the stations involved are below limits for that mix.

370280148.doc Issued March 2002 Page 29


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

Certain precautions should be observed when applying chemical anti-icing fluids,


and these are:

Anti-icing fluid must NOT be applied on top of a similar, earlier coat


If possible, the engines or the APU should not be operated during snow/ice
removal
The fluid should not be sprayed directly onto windscreens, windows, vanes,
pitot heads or probes
The minimum quantity of fluid should be used in the air conditioning intake
areas
If possible the fluid should not be sprayed onto lubricated parts, such as
landing gear legs

16.7.8 Inspection after De-Icing/Anti-Icing Procedures

The following inspections should be done on completion of a de-icing procedure:

External surfaces, for signs of residual snow or ice, particularly in the vicinity
of control surface gaps and hinges
All protrusions and vents, for signs of damage
Control surfaces for full and free movement by hand. Where this is not
possible the pilot's controls should be used, bearing in mind that power-
operated controls exert large forces and could cause damage if any part of the
control surface is frozen
Landing gear mechanisms, doors, bays and wheel brakes, for snow and ice
deposits
Up-locks and micro-switches, for correct operation
Tyres to ensure that they are not frozen to the ground. They should be freed
by the application of hot air to the ice (not the tyre) and the aircraft moved to a
dry area
Engine air intakes for ice and snow deposits
Gas turbine engines for freedom of rotation by hand. Restriction may indicate
icing in the compressor region and the engine should be blown through with
hot air immediately before starting until the rotating parts are free
Shock absorber struts and hydraulic jacks for leaks caused by contraction of
seals and metal parts
Tyre pressures and shock absorber pressure and extension

Following the inspections an entry should be made in the Tech. Log, indicating
that the De-Icing/Anti-Icing procedure has been completed.

Page 30 370280148.doc Issued March 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

16.8 Ground Electrical Supplies

Ground electrical supplies are normally limited to either 28 volts dc or 115 volts
ac, depending upon the systems of the aircraft. Most modern aircraft have at
least one 115 volt ac system (as well as a 28 volt dc one), so they will normally be
supplied with 115 volts ac from an external power supply.

Airfields normally supply electricity to aircraft through external generators called


Ground Power Units (GPUs), or have underground supplies, which are connected
to the aircraft via the air-bridge, or from beneath the ramp surface.

When an external electric supply is required inside the hangar, its generation will
normally be through transformer rectifier units. An external power control box may
be installed on the hangar wall and the required output for a particular aircraft can
be selected.

To prevent accidentally connecting-up of incorrect supplies, all aircraft have


separately-shaped plugs and sockets. The 28 volt dc supply usually has a three-
pin connection whilst the 115 volt ac utilises a much larger, six-pin plug and
socket (refer to Fig. 5).

The 28 volt dc connection has two pins which are longer than the third. The
longer pins are the supply connections whilst the shorter pin acts as a safety
interlock, to ensure that the power is cut-off, if the cable is inadvertently pulled out
without the power being switched off first.

The 115 volt ac connection has six pins, with four pins being longer than the other
two. The four longer pins provide the three phases and the neutral connection
whilst the short pins provide the safety interlock.

370280148.doc Issued March 2002 Page 31


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

3 PIN EXTERNAL
POWER RECEPTACLE
EARTH

EXTERNAL
SUPPLY SOCKET

POSITIVE D.C.

3 PIN
PLUG

POSITIVE D.C.
ACCESS
DOOR

dc Power Socket and Receptacle

EXTERNAL NOSE
POWER WHEEL
READY SERVICE
WELL
LIGHT INTERPHONE
LIGHTS
CONNECTION

A.C. PHASE A

A.C. PHASE B

A.C. PHASE C

A.C. NEUTRAL

D.C.

ac Power Receptacle

Ground Electrical Supplies


Fig. 5

Page 32 370280148.doc Issued March 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

16.9 Ground Hydraulic Supplies

Hydraulic test rigs are available, to supply aircraft with a source of hydraulic
power without the need for running the engines or APU. These test rigs are
normally powered either by internal combustion, or by electric, motors. They must
use the same type of hydraulic pump and fluid as the aircraft under test, to allow
testing of items such as the timing of system operations.

The aircraft has an access panel, behind which are a set of quick-connect
couplings, allowing the rig hoses to be easily connected to the aircrafts system
without the need for bleeding the system of air. This is achieved by use of non-
return valves, which only open when the couplings are fully tightened.

Before connecting a hydraulic testing rig to an aircraft, it must be ensured that all
of the lines and couplings are thoroughly clean, so that no dirt can get into the
aircrafts system.

16.9.1 Safety, Health and Servicing Precautions

Phosphate ester-based hydraulic fluids constitute a major health risk. Extreme


care should be taken when handling this fluid and the following precautions
should be taken:

A mask must be worn when the possibility of inhaling the fluid in an atomised
form exists. The fluid irritates the respiratory passages and can cause
sneezing and coughing
Eye protection is essential when the possibility of atomised spray exists. If
fluid contacts the eyes, they should be flushed with large quantities of
clean/sterile water and medical advice sought promptly
Hands must be washed thoroughly after working with these fluids and
particularly before eating or smoking
Hydraulic fluid must not be allowed to contact the skin for excessive periods.
Barrier cream and protective gloves must be put on before starting work
Contaminated overalls should be changed as soon as possible after contact
with the fluid.

A typical hydraulic test rig might have a 75kW (100 hp) electric motor, driving the
pump through a gearbox, clutch and a flexible coupling. The output could be in
the region of 175 litres per minute (38 gallons per minute) at 200 kPa (3000 psi).

The oil would be filtered to the standard required by the aircraft system, typically,
3 microns.

370280148.doc Issued March 2002 Page 33


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

Most hydraulic rigs have a small header tank of system oil. It would utilise the
aircrafts oil for the majority of operations, with the header tank keeping the
system primed during coupling and uncoupling operations.

The flow valves, which are often integral parts the rigs, must be kept closed until
all the hoses have been connected and the rig is ready to run. The motor is
started and once the operating pressure is indicated on the rig gauges, the valves
can be opened and the rig then forms part of the aircraft system. This will enable
the functional testing of the aircrafts hydraulic systems using the aircrafts
selector valves.

The rigs may also be provided with special gauges, such as flow meters, which
will allow the testing for internal system leakages.

16.9.2 Rig Maintenance

The rigs must have an equal or better filtration level than the aircraft being
serviced. Oil samples of the rig are taken on a regular basis, and the following
checks must be completed on a regular basis:

The rig must be kept clean and all hoses blanked when not in use
The filters must be changed or cleaned
All the gauges should be calibrated
Any electrical equipment on the rigs should be checked.

16.10 Ground Pneumatic Supplies

Pressurised aircraft usually require an adequate supply of low-pressure air, for


such tasks as engine starting, ventilation, heating and cooling, anti-icing and
pressurisation testing. This air supply is, normally, provided by the aircrafts
engine/s or APU but, when these are unavailable, a ground supply unit can be
used.

Pneumatic units can supply air at the required pressure and flow rate and are
powered by turbine engines, diesel engines or electrically powered units. The
compressors used by these units are normally axial flow, centrifugal flow, or of the
screw or lobe type.

Depending on the size of the aircraft being serviced and the air requirements, the
compressor can be mounted on a trailer chassis or on a self-propelled vehicle.

To ensure the air produced is of a suitable quality, it is normally filtered and


cleaned before being fed to the external air supply connection, which is located
on the outside of the airframe.

Page 34 370280148.doc Issued March 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

Some aircraft have two separate connections for air supplies at different points on
the airframe. The forward connection may be for low-pressure air, which is then
fed directly to the conditioning system, allowing testing of the air conditioning
system and also of the pressure hull. The aft connection may be for a higher-
pressure bleed air supply that is primarily used to start the engines if the APU is
unserviceable.

Whilst some units are dedicated air starter rigs, some can be used both for
starting and also for functional testing of the air conditioning and de-icing
systems. As with the electric and hydraulic ground power supply rigs, the output
of a pneumatic unit must match the aircrafts system for pressure and flow.

16.11 Effects of Environmental Conditions on Handling

Previous notes have mentioned a range of precautions that need to be applied


when the weather is anything less than perfect. This section will cover actions
that the technician will need to take for prevailing situations when various weather
conditions exist.

16.11.1 Cold and Wet

When the ramp is cold and wet, the friction between the aircrafts tyres and the
ramp can be reduced. This also applies to all self-propelled vehicles and, hence,
all movements on the ramp should be at a slower speed than normal, with quick
access to chocks, in the event of an emergency.

During engine ground running, it is possible that there may be a maximum power
limitation if the ramp is very wet or flooded. This will be covered in either the
Airfield Operations Manual or the Ground Handling Procedures Manual (as will
most other precautions and procedures).

If large amounts of protective clothing are worn on the ramp, it is the technicians
responsibility to ensure that nothing can get sucked into a running engine. Also,
during ground running, it is important that extra chocks are placed at the wheels
of the aircraft to prevent slippage at the higher power settings.

Falling rain (and fog) will demand that more care be taken, due to the reduced
visibility, especially when towing is in progress. The use of all normal lights, day
or night, when moving vehicles in rain, is most important.

Where there is a risk of rain and the aircraft is to be parked, then the appropriate
aircraft blanks and covers must be used. It is also inadvisable to re-fuel aircraft by
the open line (over wing) method in rain, due to the high risk of water getting into
the tank whilst the filler cap is removed. Great care must be taken, to protect the
filler neck orifice, so that very little water enters the tank.

370280148.doc Issued March 2002 Page 35


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

If a task needs to be completed on the upper surface of a wet wing, it would be


advisable to use a safety raiser or cherry picker. This mobile craning device will
allow safe access to the upper surfaces of a high wing and also provide the
technician with a safety device, to hook onto, should the need arise.

16.11.2 Snow and Ice

Many of the precautions, already mentioned, also apply in conditions of snow and
ice. Aircraft towing and taxiing may be restricted until all standing precipitation
has been cleared from the area to be used.

The loss of visibility during falling snow can be severe, especially at times of low
light, so great care must be shown if it is considered essential that an aircraft
movement must take place. This may require a larger than normal towing team
and the use of extra lights.

Most airfields that operate continuously have a plan to deal with excessive
amounts of snow. This plan might include the application of heater units or
allowing APUs to run for extended periods to keep the inside of the aircraft warm.

For aircraft, which are to be left out on the ramp, in sub-zero temperatures, it may
be necessary to drain the potable water tanks, to prevent them freezing
overnight. This will involve some care, as they should not be drained onto the
ramp, due to the risk of personnel slipping on the ice.

Other items of equipment that use water, such as heaters and pipe-work, may
also need protection in cold temperatures.

16.11.3 High Winds

High winds can cause loose objects to move across the ramp and strike the
aircraft. These can be light items such as twigs and branches but, on occasions,
heavy pieces of ground equipment, that have not been secured correctly, have
been pushed into aircraft, causing major damage.

During very high wind conditions, the smallest objects can be lethal, due to the
energy they contain.

In certain environments, such as desert climates (or at airfields near seashores),


sand and dust, driven by the wind, can enter small crevices, causing problems
with aircraft systems and may also block filters. Where extreme conditions exist,
such as during a sand storm, then the blanking of all orifices may have to be
augmented with tape or other methods, to prevent the ingress of dust and sand.

Great care must be taken, to ensure suitable entries are made in the Technical
Log, for the complete removal of all blanking material, after the storm has abated.

Page 36 370280148.doc Issued March 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

16.11.4 High Temperature

Certain items of equipment are temperature-sensitive and, when aircraft are


operated in environments of extreme high temperature (+55C), then several
extra precautions have to be taken.

Some form of cooling must be provided to ensue that the crew does not suffer
from heat exhaustion, and reduce their efficiency. The operating temperature
electronic equipment must also be kept below a critical level, to ensure its
continued serviceability.

Most of the larger aircraft have an auxiliary power unit (APU), which can provide
a supply of bleed air to allow the air conditioning system of the aircraft to operate
on the ground.

If an APU is not available, then external air conditioning units can be connected to
the aircraft to keep the inside cool. These cooling rigs should have an air
conditioning unit of suitable capacity for the size of the aircraft that requires
cooling.

Some turbo-propeller passenger aircraft have the facility to run an engine, without
the propeller turning, to provide air conditioning on the ground.

This facility is known as the Hotel Mode and, effectively, enables an engine to
operate in a similar manner to an APU, without the need to carry extra weight.

370280148.doc Issued March 2002 Page 37


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

PAGE
INTENTIONALLY
BLANK

Page 38 370280148.doc Issued March 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

370280148.doc Issued March 2002 Page 1


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

Page 2 370280148.doc Issued March 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

During ground servicing many vehicles need to be manoeuvred close to the


airframe and some have to be in light contact with it to work properly. Contact
with the airframe by any of these vehicles can cause dents or puncturing of the
pressure hull, resulting in a time-consuming repair.

17.1.2 Inlets and Exhausts

Any inlet or exhaust can be a potential nest site for wildlife. The damage done by
these birds, rodents and insects can be very expensive to rectify. Other items that
have been known to block access holes include branches, leaves and polythene
bags.

A careful check of all inlets and exhausts, during inspections, must be made, to
ensure that there is nothing blocking them. A blocked duct can result in the
overheating of equipment, or major damage to the internal working parts of the
engine.

17.1.3 Liquid Systems

Liquid systems usually have gauges to ascertain the quantity in that particular
system. A physical quantity check is often done in addition to using the gauges,
as the gauges are not always reliable.

These systems usually include oil tanks for the engine, APU and Integrated Drive
Generators (IDG), and also the hydraulics, fuel and potable water tanks.

The cause of a lower-than-expected level should be immediately investigated,


bearing in mind, that some systems consume specific amounts of fluids during
normal operation. The consumption rate must be calculated before instigating any
trouble-shooting. A low hydraulic system should not be replenished without first
investigating the cause of the leak.

External leaks of oil and fuel systems are normally easy to locate. The
rectification of an external leak is usually achieved by simply replacing the
component, seal or pipe work at fault, and completing any tests required by the
AMM.

If the leak is internal, then a much more thorough inspection of the component
must be made, as the problem is more difficult to find. The symptoms are usually
signalled by a slower movement of the services or by the erratic operation of
services, due to the return line being pressurised.

Some hydraulic oils, especially the phosphate ester based fluids, are very toxic
and require personnel protection when working on and replenishing their
systems. Some oils used are slightly toxic so care must be taken if there is a
large leak.

370280148.doc Issued March 2002 Page 3


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

Potable water tanks are often permanently pressurised, so that a leak that starts
somewhere between the tank and the services will continue, even if the aircraft is
not flying. Once the pressure is removed, the leak can be investigated, cured and
the tank re-filled.

The physical signs of water inside the aircraft or dripping from the hull should be
the signs of a leak that requires investigation. The unpredictable passenger
consumption of water means that the tank level is no indication of a leak in the
system.

Windscreen de-icers are usually in the form of a pressurised container, which


supplies fluid on demand to the spray nozzles. If the fluid leaks onto the flight
deck it will give off a distinctive odour in the enclosed space. As the containers
are replaced when low, it is more likely that the pipe work will be the likely cause
of the leak.

17.1.4 Gaseous Systems

These include gases such as oxygen, nitrogen and air. If the gas is to be used
from a system during flight, a leak will be very hard to confirm unless a physical
check is carried out using a leak detector such as Snoop or Sherlock.

A leak from an oxygen system is extremely dangerous, due to the chances of an


explosion, if it comes into contact with oil or grease. Once the leak has been
cured, the system can be re-charged and leak tested.

Nitrogen, used in hydraulic accumulators, can leak into the liquid part of the
hydraulic system. This will make the hydraulic system feel spongy and reduce the
response of the operating actuators.

If the gas leaks into the atmosphere, the system will not function correctly and the
efficiency of the system may be reduced. The main cause of accumulators
leaking externally is due to faulty seals or gauges.

Accumulators assist the hydraulic system as an emergency backup, which only


works correctly if it is charged to the correct pressure.

Pneumatic systems contain high-pressure air of a stated pressure, and should


have the same pressure at the end of the flight as at the start. If the pressure is
low at the end of the flight, then the compressor could be suspected.

If the pressure falls between flights, it is probably due to a slow leak in the
storage system, and this can be investigated using leak-detecting fluids.

Page 4 370280148.doc Issued March 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

17.1.5 Dimensions

There are a number of places where checking the measurement of a component


can establish its serviceability. Landing gear oleo shock struts can be checked for
correct inflation, by measuring their extension. If the dimension is less than
quoted in the manual, then it may be low on pressure and further checks will be
required. These checks are usually only done during line maintenance, with
checking of the pressure being required for trouble shooting or hangar
maintenance.

Combined hydraulic and spring dampers, fitted to some landing gears, often have
one or more engraved lines on the sliding portion of the unit. This can indicate
whether the hydraulic pre-charge is correct or requires replenishment.

17.1.6 Tyres

Tyres have their serviceability indicated by the depth of the groove in the tyre
tread. The AMM gives information of what constitutes a worn or damaged tyre.

Apart from normal wear, other defects, that can affect a tyre, are cuts, blisters,
creep and low pressure.

Most tyres can be re-treaded a number of times after they have reached their
wear limits, but the retread can only be completed if the complete tyre has not
been damaged badly.

Creep is the movement of a cover around the rim, in very small movements, due
to heavy braking action. This movement is dangerous if the tyre is fitted with a
tube, as the movement can tear the charging valve out of the tube, causing a
rapid loss of pressure.

To provide an indicator, small white marks are painted across the wheel rim and
the tyre side wall cover so, if creep takes place, the marks will split in half and
indicate clearly that the tyre cover has moved in relation to the wheel rim.

The installation of tubeless covers has reduced the problem of creep, as the
valve is permanently fitted to the wheel. It is still possible for tyres to creep a
small amount, but the air remains in the tyre as the seal remains secure.

Tyre-inflation devices usually consists of high-pressure bottles fitted with a


pressure-reducing valve or a simple air compressor. The pressure a tyre should
be inflated to depends on various factors such as the weight of the aircraft.

370280148.doc Issued March 2002 Page 5


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

The correct pressure for a specific aircraft is given in the relevant AMM for the
aircraft in question. It is possible for a tyre to lose a small amount of pressure
overnight. A pressure drop of less than 10% of the recommended pressure is not
unusual, but the exact figures are given in the AMM.

If a tyre is completely deflated with the weight of the aircraft on it, or is one of a
pair on a single landing gear leg, which has run without pressure, all the tyres
concerned must be replaced due to the possible, unseen damage within the
cover. Again the AMM will dictate the conditions.

17.1.7 Wheels

Defects to aircraft wheels are usually due to impact damage from heavy landings
or from items on the runway hitting the wheel rim. Other problems can arise from
corrosion starting as a result of the impact damage and the shearing of wheel
bolts, which hold the two halves of a split wheel together. Wheels are usually
inspected thoroughly during tyre replacement and it is very unusual for serious
defects to be found during normal inspections of a wheel.

17.1.8 Brakes

Brake units are normally attached onto the axle of an undercarriage leg, and
located inside the well of the main wheels. During braking operation they absorb
large amounts of energy as heat. This results in the brake rotors and stators
wearing away and, if they become too hot, the stator material may break up.

Inspection of brake units between flights is essential, to check for signs of


excessive heating and to ensure that they have not worn beyond their limits.

Wear results in the total thickness of the brake pack being reduced, which means
that by measuring either the thickness of the pack, the amount of wear can be
monitored. Once the amount of wear reaches a set figure, the brake pack will be
overhauled.

If the pads are breaking up there will be signs of debris, excessive amounts of
powder and, in extreme cases, scoring of the discs. This will require immediate
replacement of the complete brake unit.

A rejected take-off at maximum weight will produce the maximum possible


amount of heat and wear. It is usual to replace all brake units and main wheels
after this has happened, but again the AMM will give the required information on
what must be changed and when.

Page 6 370280148.doc Issued March 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

17.1.9 Landing Gear Locks

These items are normally fitted to the aircrafts undercarriage as a safety device
to prevent them inadvertently collapsing. They are usually fitted when the aircraft
is to stay on the ground for some time, and removed before the next flight. The
most likely defects will be damage to the locking pin ball bearing device or the
loss of the high visibility warning flags. These flags will, hopefully, attract attention
to themselves to ensure that they are not left in position when the aircraft next
goes flying.

17.1.10 Indicators

The most common type of indicator is the blow-out disc used in fire extinguishing
and oxygen systems. This shows that a high-pressure gas bottle has discharged
its contents overboard, blowing the disc from its flush housing in the aircrafts
skin.

The reason for the ruptured disc (refer Fig. 1) could be due to a fire extinguisher
having been operated or the extinguishant having been discharged due to an
excessive pressure being reached.

Gas Bottle and


Pressure Relief Valve

Retaining Ring

Frangible Disc

Gas Bottle Bursting Disc


Fig. 1

370280148.doc Issued March 2002 Page 7


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

17.1.11 External Probes

There are several different types of probe, projecting into the airflow, to send
information to the flight deck. These can include the pitot/static probes and the
angle-of attack (AOA) probes.

To prevent these from freezing they have electrical heating elements built into
them and, occasionally, they can become overheated. Usually this is when they
are left switched on on the ground with a faulty weigh-on-wheels (WOW) switch.

This switch is designed to reduce or remove power to the probes when on the
ground, and to increase or restore it in flight. On smaller aircraft there is no WOW
switch and it is up to the pilot to turn them off after landing. If the elements
overheat they can burn out and the probes will show this by discoloration.

Probes are designed to project out from the aircraft skin, and this makes them
vulnerable to physical damage. Probes need to be regularly inspected for signs of
physical damage or discoloration.

17.1.12 Handles and Latches

Handles and latches usually wear through constant use. The handles and latches
of cargo bays and baggage holds, which are operated every time the aircraft
lands, are particularly prone to wear. Technicians have to be aware that all panel
fasteners will wear slowly and these panels must be secured in flight.

Most fasteners have a positive form of closing or locking, whilst the more
important installations use an indication system (such as painted lines and flush
fitting catches) to ensure correct closure. These must be regularly checked and,
when found worn, they should be repaired or replaced. Losing a panel in flight is
dangerous enough, but may be more so if it is drawn into one of the engines, and
causes its destruction.

17.1.13 Panels and Doors

These items can be of any size and can be faulty for several reasons. They can
be damaged by excessive use and their frames can become damaged where
items have to be passed through them (such as with baggage hold doors).

If the latches are poorly designed or badly adjusted, they may have been
operated with incorrect tools during service and may have been damaged.

Page 8 370280148.doc Issued March 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

17.1.14 Emergency System Indication

Some systems use protective covers, to prevent inadvertent operation of a


switch. These covers are usually held closed by some form of frangible device
that will indicate the system has been operated when it is broken. Thin copper
wire is, sometimes, used to hold the protective cover closed on fire extinguisher
switches. A broken wire will indicate that the cover has been lifted and the system
may have been operated. Any indication like this must be thoroughly investigated.

17.1.15 Lifed Items

There are a number of items on the aircraft that have a specific length of time in
service (known as a life). They would be major airframe and engine components
with finite fatigue lives. The company technical department monitors these and
they will be replaced during major servicing.

The components which can become unserviceable due to life expiry may include,
engine fire bottles, cabin fire extinguishers, first aid kits, portable oxygen bottles
and emergency oxygen generators.

17.1.16 Light Bulbs

These have to be checked regularly, to ensure they remain serviceable at all


times. Most bulbs with important functions like fire warning lights and
undercarriage indication will be duplicated. This can be achieved either by using
two separate bulbs or by a single, twin-filament type. The bulb covers can also be
damaged, leading to broken glass or plastic on the flight deck, with its
subsequent foreign object damage (FOD) hazard.

17.1.17 Permitted Defects

All aircraft have a list of permitted defects that do not have to be immediately
corrected. These defects can be left outstanding by the operator until a more
convenient time can be found to rectify them.

370280148.doc Issued March 2002 Page 9


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

17.2 Locations of Corrosion in Aircraft

Certain locations in aircraft are more prone to corrosion than others. The rate of
deterioration varies widely with aircraft design, build, operational use and
environment. External surfaces are open to inspection and are usually protected
by paint. Magnesium and aluminium alloy surfaces are particularly susceptible to
corrosion along rivet lines, lap joints, fasteners, faying surfaces and where
protective coatings have been damaged or neglected.

17.2.1 Exhaust Areas

Fairings, located in the path of the exhaust gases of gas turbine and piston
engines, are subject to highly corrosive influences. This is particularly so where
exhaust deposits may be trapped in fissures, crevices, seams or hinges. Such
deposits are difficult to remove by ordinary cleaning methods.

During maintenance, the fairings in critical areas should be removed for cleaning
and examination. All fairings, in other exhaust areas, should also be thoroughly
cleaned and inspected. In some situations, a chemical barrier can be applied to
critical areas, to facilitate easier removal of deposits at a later date, and to reduce
the corrosive effects of these deposits.

17.2.2 Engine Intakes and Cooling Air Vents

The protective finish, on engine frontal areas, is abraded by dust and eroded by
rain. Heat-exchanger cores and cooling fins may also be vulnerable to corrosion.

Special attention should be given, particularly in a corrosive environment, to


obstructions and crevices in the path of cooling air. These must be treated, as
soon as is practical.

17.2.3 Landing Gear

Landing gear bays are exposed to flying debris, such as water and gravel, and
require frequent cleaning and touching-up. Careful inspection should be made of
crevices, ribs and lower-skin surfaces, where debris can lodge. Landing gear
assemblies should be examined, paying particular attention to magnesium alloy
wheels, paint-work, bearings, exposed switches and electrical equipment.

Frequent cleaning, water-dispersing treatment and re-lubrication will be required,


whilst ensuring that bearings are not contaminated, either with the cleaning water
or with the water-dispersing fluids, used when re-lubricating.

Page 10 370280148.doc Issued March 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

17.2.4 Bilge and Water Entrapment Areas

Although specifications call for drains wherever water is likely to collect, these
drains can become blocked by debris, such as sealant or grease. Inspection of
these drains must be frequent. Any areas beneath galleys and toilet/wash-rooms
must be very carefully inspected for corrosion, as these are usually the worst
places in the whole airframe for severe corrosion. The protection in these areas
must also be carefully inspected and renewed if necessary.

17.2.5 Recesses in Flaps and Hinges

Potential corrosion areas are found at flap and speed brake recesses, where
water and dirt may collect and go unnoticed, because the moveable parts are
normally in the closed position. If these items are left open, when the aircraft is
parked, they may collect salt, from the atmosphere, or debris, which may be
blowing about on the airfield. Thorough inspection of the components and their
associated stowage bays, is required at regular intervals.

The hinges, in these areas, are also vulnerable to dissimilar metal corrosion,
between the steel pins and the aluminium tangs. Seizure can also occur, at the
hinges of access doors and panels that are seldom used.

17.2.6 Magnesium Alloy Skins

These, give little trouble, providing the protective surface finishes are undamaged
and well maintained. Following maintenance work, such as riveting and drilling, it
is impossible to completely protect the skin to the original specification. All
magnesium alloy skin areas must be thoroughly and regularly inspected, with
special emphasis on edge locations, fasteners and paint finishes.

17.2.7 Aluminium Alloy Skins

The most vulnerable skins are those which have been integrally machined,
usually in main-plane structures. Due to the alloys and to the manufacturing
processes used, they can be susceptible to intergranular and exfoliation
corrosion.

Small bumps or raised areas under the paint sometimes indicate exfoliation of the
actual metal. Treatment requires removal of all exfoliated metal followed by
blending and restoration of the finish.

370280148.doc Issued March 2002 Page 11


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

17.2.8 Spot-Welded Skins and Sandwich Constructions

Corrosive agents may become trapped between the metal layers of spot-welded
skins and moisture, entering the seams, may set up electrolytic corrosion that
eventually corrodes the spot-welds, or causes the skin to bulge. Generally, spot-
welding is not considered good practice on aircraft structures.

Cavities, gaps, punctures or damaged places in honeycomb sandwich panels


should be sealed to exclude water or dirt. Water should not be permitted to
accumulate in the structure adjacent to sandwich panels. Inspection of
honeycomb sandwich panels and box structures is difficult and generally requires
that the structure be dismantled.

17.2.9 Electrical Equipment

Sealing, venting and protective paint cannot wholly obviate the corrosion in
battery compartments. Spray, from electrolyte, spreads to adjacent cavities and
causes rapid attack on unprotected surfaces. Inspection should also be extended
to all vent systems associated with battery bays.

Circuit-breakers, contacts and switches are extremely sensitive to the effects of


corrosion and need close inspection.

17.2.10 Control Cables

Loss of protective coatings, on carbon steel control cables can, over a period of
time, lead to mechanical problems and system failure. Corrosion-resistant cables,
can also be affected by corrosive, marine environments.

Any corrosion found on the outside of a control cable should result in a thorough
inspection of the internal strands and, if any damage is found, the cable should
be rejected.

Cables should be carefully inspected, in the vicinity of bell-cranks, sheaves and in


other places where the cables flex as there is more chance of corrosion getting
inside the cables when the strands are moving around (or being moved by) these
items.

Page 12 370280148.doc Issued March 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

17.3 Corrosion Removal, Assessment and Reprotection

Due to the high cost of modern aircraft, operators are expecting them to last
much longer than perhaps even the manufacturer anticipated. As a result, the
manufacturers have taken more care in the design of the aircraft, to improve the
corrosion-resistance of aircraft. This improvement includes the use of new
materials and improved surface treatments and protective finishes. The use of
preventative maintenance has also been emphasised more than previously.

Preventative maintenance, relative to corrosion control, should include the:

Adequate and regular cleaning of the aircraft


Periodic lubrication (often after the cleaning) of moving parts
Regular and detailed inspection for corrosion and failure of protective
treatments
Prompt treatment of corrosion and touch-up of damaged paint
Keeping of drain holes clear
Draining of fuel cell sumps
Daily wiping down of most critical areas
Sealing of aircraft during foul weather and ventilation on sunny days
Use of protective covers and blanks.

General treatments for corrosion removal include:

Cleaning and stripping of the protective coating in the corroded area


Removal of as much of the corrosion products as possible
Neutralisation of the remaining residue
Checking if damage is within limits
Restoration of protective surface films
Application of temporary or permanent coatings or paint finishes.

17.3.1 Cleaning and Paint Removal

It is essential that the complete suspect area be cleaned of all grease, dirt or
preservatives. This will aid in determining the extent of corrosive spread. The
selection of cleaning materials will depend on the type of matter to be removed.

Solvents such as trichloroethane (trade name Genklene) may be used for oil,
grease or soft compounds, while heavy-duty removal of thick or dried compounds
may need solvent/emulsion-type cleaners.

General-purpose, water-removable stripper is recommended for most paint


stripping. Adequate ventilation should be provided and synthetic rubber surfaces
such as tyres, fabrics and acrylics should be protected (remover will also soften
sealants).

370280148.doc Issued March 2002 Page 13


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

Rubber gloves, acid-repellent aprons and goggles, should be worn by personnel


involved with paint removal operations. The following represents a typical paint
stripping procedure:

Brush the area with stripper, to a depth of approximately 0.8 mm 1.6 mm


(0.03 in 0.06 in). Ensure that the brush is only used for paint stripping
Allow the stripper to remain on the surface long enough for the paint to
wrinkle. This may take from 10 minutes to several hours
Re-apply the stripper to those areas which have not stripped. Non-metallic
scrapers may be used to assist the stripping action
Remove the loosened paint and residual stripper by washing and scrubbing
the surface with water and a broom or brush. Water spray may assist, or
the use of steam cleaning equipment may be necessary.

Note: Strippers can damage composite resins and plastics, so every effort should
be made to 'mask' these vulnerable areas.

17.3.2 Ferrous Metals

Atmospheric oxidation of iron or steel surfaces causes ferrous oxide (rust) to be


deposited. Some metal oxides protect the underlying base metal, but rust
promotes additional attack by attracting moisture and must be removed.

Rust shows on bolt heads, nuts or any unprotected hardware. Its presence is not
immediately dangerous, but it will indicate a need for maintenance and will
suggest possible further corrosive attack on more critical areas. The most
practical means of controlling the corrosion of steel is the complete removal of
corrosion products by mechanical means.

Abrasive papers, power buffers, steel wool and wire brushes are all acceptable
methods of removing rust on lightly stressed areas. Residual rust usually remains
in pits and crevices. Some (dilute) phosphoric acid solutions may be used to
neutralise oxidation and to convert active rust to phosphates, but they are not
particularly effective on installed components.

Corrosion on high-stressed steel components may be dangerous and should be


removed carefully with mild abrasive papers or fine buffing compounds. Care
should be taken not to overheat parts during corrosion removal. Protective
finishes should be re-applied immediately.

17.3.3 Aluminium and Aluminium Alloys

Corrosion attack, on aluminium surfaces, gives obvious indications, since the


products are white and voluminous. Even in its early stages, aluminium corrosion
is evident as general etching, pitting or roughness.

Page 14 370280148.doc Issued March 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

Aluminium alloys form a smooth surface oxidation, which provides a hard shell,
that, in turn, may form a barrier to corrosive elements. This must not be confused
with the more serious forms of corrosion.

General surface attack penetrates slowly, but is speeded up in the presence of


dissolved salts. Considerable attack can take place before serious loss of
strength occurs. Three forms of attack, which are particularly serious, are:

Penetrating pit-type corrosion through the walls of tubing


Stress corrosion cracking under sustained stress
Intergranular attack ,characteristic of certain improperly heat treated alloys.

Treatment involves mechanical or chemical removal of as much of the corrosion


products as possible and the inhibition of residual materials by chemical means.

This, again, should be followed by restoration of permanent surface coatings.

17.3.4 Alclad

WARNING: USE ONLY APPROVED PAINT STRIPPERS IN THE VICINITY OF


REDUX BONDED JOINTS. CERTAIN PAINT STRIPPERS WILL ATTACK AND
DEGRADE RESINS. USE ADEQUATE PERSONAL PROTECTIVE EQUIPMENT
WHEN WORKING WITH CHEMICALS. USE ONLY THE APPROVED FLUIDS
FOR REMOVING CORROSION PRODUCTS. INCORRECT COMPOUNDS WILL
CAUSE SERIOUS DAMAGE TO METALS.

Obviously great care must be taken, not to remove too much of the protective
aluminium layer by mechanical methods, as the core alloy metal may be
exposed, therefore, where heavy corrosion is found, on clad aluminium alloys, it
must be removed by chemical methods wherever possible.

Corrosion-free areas must be masked off and the appropriate remover (usually a
phosphoric acid-based fluid) applied, normally with the use of a stiff (nylon)
bristled brush, to the corroded surface, until all corrosion products have been
removed. Copious amounts of clean water should, next, be used to flood the area
and remove all traces of the acid, then the surface should be dried thoroughly.

Note: A method of checking that the protective aluminium coating remains intact
is by the application of one drop of diluted caustic soda to the cleaned area. If the
alclad has been removed, the aluminium alloy core will show as a black stain,
whereas, if the cladding is intact, the caustic soda will cause a white stain.

The acid must be neutralised and the area thoroughly washed and dried before a
protective coating (usually Alocrom 1200 or similar) is applied to the surface.

Further surface protection may be given by a coat of suitable primer, followed by


the approved top coat of paint.

370280148.doc Issued March 2002 Page 15


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

17.3.5 Magnesium Alloys

The corrosion products are removed from magnesium alloys by the use of
chromic/sulphuric acid solutions (not the phosphoric acid types), brushed well into
the affected areas. Clean, cold water is employed to flush the solution away and
the dried area can, again, be protected, by the use of Alocrom 1200 or a similar,
approved, compound.

17.3.6 Acid Spillage

An acid spillage, on aircraft components, can cause severe damage. Acids will
corrode most metals used in the construction of aircraft. They will also destroy
wood and most other fabrics. Correct Health and Safety procedures must be
followed when working with such spillages.

Aircraft batteries, of the lead/acid type, give off acidic fumes and battery bays
should be well ventilated, while surfaces in the area should be treated with anti-
acid paint. Vigilance is required of everyone working in the vicinity of batteries, to
detect (as early as possible) the signs of acid spillage. The correct procedure to
be taken, in the event of an acid spillage, is as follows:

Mop up as much of the spilled acid, using wet rags or paper wipes. Try not
to spread the acid
If possible, flood the area with large quantities of clean water, taking care
that electrical equipment is suitably protected from the water
If flooding is not practical, neutralise the area with a 10% (by weight)
solution of bicarbonate of soda (sodium bicarbonate) with water
Wash the area using this mixture and rinse with cold water
Test the area, using universal indicating paper (or litmus paper), to check if
acid has been cleaned up
Dry the area completely and examine the area for signs of damaged paint or
plated finish and signs of corrosion, especially where the paint may have
been damaged.
Remove corrosion, repair the damage and restore the surface protection as
appropriate.

17.3.7 Alkali Spillage

This is most likely to occur from the alternative Nickel-Cadmium (Ni-Cd) or Nickel-
Iron (Ni-Fe) type of batteries, containing an electrolyte of Potassium Hydroxide
(or Potassium Hydrate).

The compartments of these batteries should also be painted with anti-corrosive


paint and adequate ventilation is as important as with the lead/acid type of
batteries. Proper Health and Safety procedures are, again, imperative.

Page 16 370280148.doc Issued March 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

Removal of the alkali spillage, and subsequent protective treatment, follows the
same basic steps as outlined in acid spillage, with the exception that the alkali is
neutralised with a solution of 5% (by weight) of chromic acid crystals in water.

17.3.8 Mercury Spillage

WARNING: MERCURY (AND ITS VAPOUR) IS EXTREMELY TOXIC.


INSTANCES OF MERCURY POISONING MUST, BY LAW, BE REPORTED TO
THE HEALTH AND SAFETY EXECUTIVE. ALL SAFETY PRECAUTIONS
RELATING TO THE SAFE HANDLING OF MERCURY MUST BE STRICTLY
FOLLOWED.

Mercury contamination is far more serious than any of the battery spillages and
prompt action is required to ensure the integrity of the aircraft structure.

While contamination from mercury is extremely rare on passenger aircraft,


sources of mercury spillage result from the breakage of (or leakage from)
containers, instruments, switches and certain test equipment. The spilled mercury
can, quickly, separate into small globules, which have the capability of flowing
(hence its name Quick Silver) into the tiniest of crevices, to create damage.

Mercury can rapidly attack bare light alloys (it forms an amalgam with metals),
causing intergranular penetration and embrittlement which can start cracks and
accelerate powder propagation, resulting in a potentially catastrophic weakening
of the aircraft structure.

Signs of mercury attack on aluminium alloys are greyish powder, whiskery


growths, or fuzzy deposits. If mercury corrosion is found, or suspected, then it
must be assumed that intergranular penetration has occurred and the structural
strength is impaired. The metal in that area should be removed and the area
repaired in accordance with manufacturers instructions.

Ensure that toxic vapour precautions are observed at all times during the
following operations:

Do not move aircraft after finding spillage. This may prevent spreading.
Remove spillage carefully by one of the following mechanical methods:
Capillary brush method (using nickel-plated carbon fibre brushes).
Heavy-duty vacuum cleaner with collector trap.
Adhesive tape, pressed (carefully) onto globules may pick them up
Foam collector pads (also pressed, carefully, onto globules).
Alternative, chemical methods, of mercury recovery entail the use of:
Calcium polysulphide paste
Brushes, made from bare strands of fine copper wire
Neutralise the spillage area, using Flowers of Sulphur
Try to remove evidence of corrosion

370280148.doc Issued March 2002 Page 17


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

The area should be further checked, using radiography, to establish that all
globules have been removed and to check extent of corrosion damage
Examine area for corrosion using a magnifier. Any parts found contaminated
should be removed and replaced.

Note 1: Twist drills (which may be used to separate riveted panels, in an attempt
to clean contaminated surfaces) must be discarded after use.
Note 2: Further, periodic checks, using radiography, will be necessary on any
airframe that has suffered mercury contamination.

17.4 Permanent Anti-Corrosion Treatments

These are intended to remain intact throughout the life of the component, as
distinct from coatings, which may be renewed as a routine servicing operation.

They give better adhesion for paint and most resist corrosive attack better than
the metal to which they are applied.

17.4.1 Electro-Plating

There are two categories of electro-plating, which consist of:

Coatings less noble than the basic metal. Here the coating is anodic and so,
if base metal is exposed, the coating will corrode in preference to the base
metal. Commonly called sacrificial protection, an example is found in the
cadmium (or zinc) plating of steel.
Coatings more noble (e.g. nickel or chromium on steel) than the base metal.
The nobler metals do not corrode easily in air or water and are resistant to
acid attack. If, however, the basic metal is exposed, it will corrode locally
through electrolytic action. The attack may result in pitting corrosion of the
base metal or the corrosion may spread beneath the coating.

17.4.2 Sprayed Metal Coatings

Most metal coatings can be applied by spraying, but only aluminium and zinc are
used on aircraft. Aluminium, sprayed on steel, is frequently used for high-
temperature areas. The process (aluminising), produces a film about 0.1 mm
(0.004 in) thick, which prevents oxidation of the underlying metal.

17.4.3 Cladding

The hot rolling of pure aluminium onto aluminium alloy (Alclad) has already been
discussed, as has the problem associated with the cladding becoming damaged,
exposing the core, and the resulting corrosion of the core alloy.

Page 18 370280148.doc Issued March 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

17.4.4 Surface Conversion Coatings

These are produced by chemical action. The treatment changes the immediate
surface layer into a film of metal oxide, which has better corrosion resistance than
the metal. Among those widely used on aircraft are:

Anodising of aluminium alloys, by an electrolytic process, which thickens the


natural, oxide film on the aluminium. The film is hard and inert
Chromating of magnesium alloys, to produce a brown to black surface film
of chromates, which form a protective layer
Passivation of zinc and cadmium by immersion in a chromate solution.

Other surface conversion coatings are produced for special purposes, notably the
phosphating of steel. There are numerous proprietary processes, each known by
its trade name (e.g. Bonderising, Parkerising, or Walterising).

370280148.doc Issued March 2002 Page 19


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

17.5 Non-Destructive Testing/Inspection (NDT/NDI) Techniques

Among the many inspection tasks, done by aircraft serving technicians, are those
involving Scheduled Maintenance Inspections (SMIs).

SMI's are special inspections, detailed by the manufacturer, to be done at a


specified time period. When doing these inspections the ultimate aim is to ensure
that the aircraft (or part) being inspected, remains in a safe condition or that it
complies with the original design specification.

The common factor, in all the inspection/test procedures is that they entail
techniques that do not affect the continued serviceability of the components
under inspection. They are, in fact, non-destructive testing/inspection techniques.

Non-destructive testing (NDT) or, in America, Non-destructive inspection (NDI)


techniques, involve the use of such methods as:

Visual and Assisted Visual Inspections


Remote Viewing Instruments
Penetrant Flaw Detection (PFD)
Magnetic Particle Flaw Detection (MPFD)
Eddy Current Flaw Detection (ECFD)
Ultrasonic Flaw Detection (UFD)
Radiographic Flaw Detection (RFD).

It is incumbent on all aircraft servicing technicians, regardless of trade or level of


certification, to be constantly vigilant and to use their eyes to detect the slightest
imperfection in and around the areas of aircraft or component parts on which they
are working.

When approaching an aircraft, a perfunctory glance may reveal the fact that one
wing is lower than the other, which could indicate a difference in the fluid levels of
the respective landing gear struts, different tyre pressures or, perhaps, a deflated
tyre.

Missing or badly secured panels have often been discovered by such alert
observations, as have potentially catastrophic structural failures, and the student
is urged to adopt this vigilant attitude as quickly as possible to ensure the safety
of all aircraft and the people that fly in them.

While all aircraft servicing technicians can, therefore, do visual and assisted
visual inspections, only those who have received appropriate training will be
authorised to do certain PFD techniques. The more sophisticated MPFD, ECFD,
UFD, and RFD techniques will be done by specially trained and approved NDT
(NDI) technicians.

Page 20 370280148.doc Issued March 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

17.5.1 Visual/Assisted Visual Inspections

The appropriate visual or assisted visual inspection techniques will be detailed in


the relevant servicing manuals but, generally, they will depend on such factors as:

The nature of the item being inspected (i.e. the material from which it is
made): It may be metallic, plastic, rubber or any other type of material
The purpose of the inspection: It may be to establish whether the item is
suffering from a known fault or to confirm the integrity of a previous repair
The location of the item to be inspected: It may be installed in an aircraft or
removed from an aircraft. In most cases the maintenance schedule will specify
that an item is always inspected without removal from the aircraft. The term
in-situ has previously been used to describe this instance
The inspection surface: Whether it is an internal or an external surface. The
normal convention is that inspections are external unless otherwise stated
The time available for the inspection: This is often dictated by circumstances,
in that, if a tyre needs to be inspected for wear, it should be able to be
checked in a few minutes. A major aircraft inspection, on a large aircraft, is
however, normally planned to take many days
The degree or depth of the inspection: Depending on the criticality of the
component, or its adjacent structure, to the safety of the aircraft.

It should be stressed here that, whenever a visual inspection is being done, there
must be adequate illumination of the inspection site, to ensure that small defects
are able to be detected.

Some visual inspections may dictate that a specific amount of illumination (in a
stated number of lux) be available during the inspection.

To assist in visual inspections, use is frequently made of such aids as:

Inspection Mirrors
Magnifying Glasses.

Inspection mirrors enable the technician to see the remote surface of components
and into places that normal vision is restricted. Selections of inspection mirrors
are available, mounted on the end of a handle or rod. Such mirrors should be
mounted by means of a universal joint so that they can be positioned at various
angles.

A development of this device has the ability to change the angle of the mirror by
remote control. A rack and pinion mechanism passes through the stem and is
controlled by a knob on the handle.

370280148.doc Issued March 2002 Page 21


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

This permits a range of angles to be obtained, after insertion of the instrument


into the structure. Some instruments come equipped with integral non-dazzle
illumination.

Magnifying glasses are most useful instruments, to assist with the close
inspection of an airframe. They are capable of clarifying details, when normal
visual inspection only produces a suspicion of a crack or corrosion. Magnifying
glasses vary in design from the pocket type, with a magnification factor of times
two (x2), to the stereoscopic type with a magnification of up to x32.

The magnification factor relates to the size of an object, seen through the
magnifying lens, compared with the size of the object, viewed with the naked eye,
at a distance of 250 mm (10 in).

For day-to-day inspection of structures, a hand instrument with a x8 magnification


and integral illumination could be used. Magnification above this value should not
be used unless specified, because the limited area of observation does not reveal
the surrounding area. A higher magnification lens can be used, once the lower
powered lens has identified a problem.

Note: Magnifying glasses and similar inspection instruments will provide the best
results only when the area under inspection is well illuminated.

17.5.2 Remote Viewing Instruments

These instruments have a variety of different names, although they all, basically,
operate on similar principles. Whether they are called borescopes or fibrescopes,
(or, collectively, introscopes), they are optical instruments used for the inspection
of the remote areas of structures, components or engines, which would be,
otherwise, not directly viewable.

Note: A detailed knowledge of the internal structure of the component under


inspection is essential, and proper training in their use should be obtained, before
inspections involving remote viewing instruments are attempted.

Borescopes consist of ostensibly rigid tubes of nickel-plated brass or of stainless


steel. The outer diameters of the tubes may range from approximately 5.5 mm
(0.22 in) to 11 mm (0.43 in) with lengths from 230 mm (9 in) to 1 750 mm (69 in).

While they do possess a degree of rigidity, they can be very easily bent if too
much sideways force is applied to them, so great care must be taken in their use.

Inside the thin metal tube is a complex series of precision optical lenses and
mirrors, surrounded by a bundle of very fine glass fibre filaments, which guide
light to the viewing end of the tube.

Page 22 370280148.doc Issued March 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

The light is provided by a box, containing an electrical transformer, a high-


intensity, light bulb of quartz-iodine, Xenon or something similar (which is
mounted in front of a reflector), and a cooling fan.

The light source box is usually connected to a mains outlet and the powerful light
is transmitted to the borescope by means of a connecting flexible cable which
also contains a guide bundle of glass fibres.

In this way cold yet brilliant light is provided at the viewing area, to give the
necessary high quality illumination without the hazards associated with heat and
any flammable fluids which may be present in the viewing area.

Rigid borescopes are provided with several versions of viewing ends, which allow
either a forward view, a lateral view (normal to the longitudinal axis of the tube), a
forward oblique or a retrograde (reverse) view of the inspection area.

With the exception of those with a forward view end, all the other borescopes
may also have the capability of rotating the tube around the longitudinal axis, so
that a full 360 internal view of the area is possible. They also have adjustable
focus of the eyepiece, to minimise eye strain on the viewer and to accommodate
the various levels of acuity of the inspectors eyesight.

Fibrescopes are flexible and, probably because of this, they are extremely prone
to abuse and damage. As the name implies, they rely on fibre optic cables rather
than a rigid tube and lenses/mirrors to provide the image of the inspection area.

The image is viewed through a bundle of fibre optic strands, while the object is
illuminated by light transmitted through another surrounding bundle of fibre optic
strands. Diameters and lengths of fibrescopes are similar to those of rigid
borescopes and they are also provided with the various viewing ends and
focussing arrangements.

Some fibrescopes have a controllable distal viewing end, to allow articulation


through almost 360 on both an X and Y lateral axis. These (refer to Fig. 2) are
most often used (in addition to borescopes) to inspect the inside of gas turbine
engines, but can also be used for many other inspections such as; loose article
checks, fuel leaks etc.

The images, presented by borescopes and fibrescopes, may be viewed directly


through an eyepiece, as stated, or they may be displayed on a TV screen via a
video camera, which can be attached to the eyepiece.

The results of the inspection can also be recorded, by means of a video tape, and
retained, for future comparisons of possible deterioration of the inspection area.

370280148.doc Issued March 2002 Page 23


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

Eye
Piece Focus
Control
Fibre Optic Cable
Operating
from Light Box
Knob to
Control
Articulating Igniter Plug Hole
Distal End

By-Pass
Duct

Distal
End

Burner

Turbine Blades
Combustion and Nozzle Guide
Chamber Vanes

Use of a Fibrescope inside a Gas Turbine Engine


Fig. 2

Borescopes and Fibrescopes may be used for the inspection of gas turbine
engine:
Compressors: for damage to Fans, FOD, Interference between Rotors and
Stators, Surge damage, and Bearing Oil Leakage
Combustion Sections: for signs of Burning, Cracking, Distortion, and Carbon
Build-up
Turbine Sections: for signs of Burning, Cracks, Dents, Deposits of Melted
Metals and Nicks.

Note: When using remote viewing instruments for engine inspections it must be
ensured that:

The engine must be allowed to cool down before inserting the scopes
Windmilling (or inadvertent Starting) of the engine must be prevented by
gagging or removing the appropriate fuses/circuit breakers and placing
warning placards on the flight deck
Contamination of the instruments, by Fuel, Grease and Oil, must be avoided
Borescopes do not get bent and Fibrescopes do not get kinked nor crushed.

Page 24 370280148.doc Issued March 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

Remote viewing instruments may also be used to inspect many other areas of an
aircraft. Typical areas would include:

Electrical Components
Electrical Looms
Enclosed Structural Parts
Fuel System Components
Hydraulic System Components.

Wherever they are used, there are certain difficulties involved with the
interpretation of what is seen through the instruments. When using remote
viewing instruments, it is recommended that the inspecting technician should:

Be fully trained in the use (and care) of the instruments being used
Be familiar with the layout of the structure or component under inspection
If possible, have a spare or an example of the part near at hand with which to
compare the images from the inspection area
Use the experience of other inspectors where doubt exists (or consult
previous video recordings etc.)
Refer to the appropriate servicing manual for guidance whenever necessary.

17.5.3 Penetrant Flaw Detection (PFD)

Before discussing the application of PFD techniques it is necessary to highlight


the health hazards associated with working with PFD materials and to consider
the recommended First Aid treatments and the Safety Precautions, which need to
be observed, during their use. The hazards include:

Contact with the eyes: to prevent the possibility, chemical proof goggles
should be worn. If, despite this, eye contamination occurs, then the eyes must
initially be irrigated with copious amounts of water and proper medical
assistance sought
Contact with the skin: due to the de-fatting action of the chemicals, barrier
cream should be applied to the hands before work commences and, where
prolonged contact is probable, protective PVC-type gloves should be worn.
Contaminated skin should be thoroughly washed with warm soap and water
and, after drying, a lanolin-based cream applied. If irritation persists then
medical attention is needed
Ingestion: food must not be consumed while doing PFD procedures and
hands should be carefully washed before eating. If chemicals are ingested
then medical help must be sought. VOMITING SHOULD NOT BE INDUCED
Inhalation: face masks should be worn where concentrations of fumes or
particles are high and there must always be adequate ventilation. Victims who
become nauseous, dizzy or drowsy should be moved to fresh air and medical
advice sought. Resuscitation methods should be used where asphyxiation
occurs and breathing has stopped and the Emergency Services summoned.

370280148.doc Issued March 2002 Page 25


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

Fire: all the necessary fire precautions must be observed (CO 2 , Foam and Dry
Powder extinguishers are the recommended types) and, in the event of a fire,
any ventilation should be switched off first
Storage: PFD chemicals should be stored in a dry area, away from heat and
direct sunlight
Spillage: any spillages should be soaked up with absorbent materials
Transport: appropriate precautions, depending on the flash point of the
particular chemicals should be observed
Disposal: materials should be treated as oily waste and, where large
quantities are involved, must not be discharged into public sewers or
waterways.

Penetrant flaw detection may be used to detect surface-breaking discontinuities


in any non-porous materials, including ceramics metals, and plastics. It may also
be used to detect porosity in those materials that should not be porous, leaks in
tanks and cracking of internal bores.

The basic principle of penetrant flaw detection is that a liquid (usually oil-based) is
applied, to the pre-cleaned surface of the material under inspection, and is then
allowed to dwell on the surface for a specified time (the dwell or contact time).

During the dwell time, and due to its characteristics, some of the liquid penetrates
into any fine surface discontinuities by capillarity (or capillary action). Capillarity is
associated with the surface tension of a liquid, which causes it to rise (or fall) in
fine capillaries or tubes. It is the action, which causes moisture, in the ground, to
be transmitted to the topmost leaves of a tree. The height (or depth) to which a
liquid can travel in a capillary tube is given by the formula:

h = 2T Cos
gr

Where T = The surface tension of the liquid


= The angle of contact (wetting angle) of the liquid with the capillary
= The density of the liquid
g = The acceleration due to gravity
r = The radius of the capillary.

From the formula it can be seen that a liquid with a low wetting angle and a
comparatively high surface tension (but lower than that of water) will constitute a
good penetrant.

After the allotted dwell time the excess penetrant is carefully removed from the
surface so that the surface is, again, clean. A white, fine powder is next applied to
the surface and this is also allowed to remain on the surface for a given time.

Page 26 370280148.doc Issued March 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

During this time any penetrant, which has entered a surface discontinuity, will
(through capillarity) seep out into the fine particles of the powder, in a similar
fashion to the action of blotting paper, and cause a stain in the powder.

This stain will develop as more penetrant is drawn out during the allotted
developer time and will provide an indication of the site of the surface
discontinuity. Indications within the first thirty seconds can be compared to the
fully developed indications, observed at the end of the developer time, and an
assessment made of the likely size of the discontinuity.

A quickly formed stain, with very little subsequent development, could indicate a
wide, but shallow discontinuity, while an initially light stain, which gradually
spreads over a greater area could indicate a narrow but comparatively deep
fissure. In other words:

The Rate of staining indicates the Width/Depth of a discontinuity.


The Extent of staining indicates the Volume of the discontinuity.

Note: This will only give an approximate assessment and is by no means an


accurate method of deciding the actual size of the discontinuity.

Properly applied PFD procedures are capable of detecting discontinuities with


widths of only 0.000004 mm (0.0001 in) but great care is needed in their
application and technicians will need to attend an approved training course before
they will be authorised to apply PFD procedures to aircraft parts.

Penetrants are available in two basic types. They are the:

Type 1 - Fluorescent penetrant: to which is added a dye, that gives very little
colour when viewed in normal light. However, when viewed in subdued
lighting conditions, and illuminated with the rays from a mercury vapour lamp,
emitting light in the ultraviolet range of the spectrum (referred to as Black
Light), the penetrant fluoresces brilliantly (yellow/green)
Type 2 - Colour Contrast: (or Visible) penetrant: which has a dark red dye
added to the penetrant liquid so that, when viewed in normal or (better)
enhanced, white light conditions, the red dye contrasts strongly against the
white background of the developer powder

The penetrants are further sub-classified by the methods, which are used to
remove the excess penetrant from the inspection surface. They are the:

Water-washable penetrants: in which the penetrant has an added emulsifier,


that allows the oil-based liquid to be easily removed from the surface by the
use of a water spray or wash. These are used, primarily, on rough surfaces
(castings etc.)

370280148.doc Issued March 2002 Page 27


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

Post-emulsification penetrants: which do not have a built-in emulsifier and,


thus, it is necessary to apply an emulsifier to the penetrant and allow an
emulsification time before the excess penetrant will be able to be removed
(again by water) from the inspection surface. These are used on the high-
grade surface finishes of alloy steels (and aluminium and magnesium alloys)
in the search for fine fatigue cracks
Solvent-removable penetrants: in which the excess penetrant is removed from
the surface by a volatile solvent.

Both the Water-washable and Post-emulsification penetrants are (usually)


confined to the Type 1 (Fluorescent) penetrants and are used in the controlled
environment of a manufacturing or overhaul establishment, for the final
acceptance of critical aerospace materials.

The Solvent-removable, Colour Contrast (Type 2) penetrants are those which will
be more likely to be used by the aircraft servicing technician, as they are the ones
which are used for the manual (In the Field) applications on limited inspection
areas of aircraft parts.

The solvent is usually trichloroethane-based, which, while being volatile


(evaporates readily), it has a low toxicity and is non-flammable.

The manual PFD process is done by technicians, with the use of the three prime
materials - the Penetrant, the Penetrant Remover (Solvent) and the Developer
-contained in their respective aerosol cans, which comprise the usual In the
Field PFD inspection kit. The PFD procedure can be broken down into the:

Initial surface preparation and thorough pre-cleaning of the inspection area


Masking of the areas adjacent to the inspection site
Application of the penetrant (with the stipulated Dwell time)
Removal of the excess penetrant from the surface
Application of the developer (and the specified Developer time)
Inspection and the recording of any significant indications
Cleaning and restoration of the surface protective finish.

Obviously if a defect is found, the fault will need to be rectified, either by an


approved repair scheme or by replacement of the defective component.

Page 28 370280148.doc Issued March 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

In the initial surface preparation the area of the inspection must be completely
clean and free from corrosion dirt, grease or oil, paint, surface treatments and
water. The presence of any of these contaminants will prevent the penetrant from
entering surface-breaking discontinuities.

Paint should be removed using an approved paint stripper, taking care not to
apply the stripper to areas which might be damaged (e.g. Redux bonded joints)
by its action. Similar care is needed with the penetrant solvents and such joints.

Care must be taken not to damage the material surface with scrapers as this
might appear as a defect. The use of non-metallic scrapers is recommended, to
avoid this problem. After paint removal, the surface should be washed with water,
dried and finally degreased, by spraying the area with the solvent remover and
allowing it to evaporate.

Harsh abrasive methods should not be used in the inspection area, as they will
tend to cause metal flow, which will cover the lips of any surface cracks and
prevent ingress of the penetrant.

If such methods must be used (to remove stubborn corrosion deposits, burnt on
carbon or oil etc.), then it may be necessary to employ some form of surface
etching process (if approved) to remove the smeared metal.

Before applying PFD procedures, the areas adjacent to the inspection site should
be protected, by masking off, to prevent contamination by the chemicals of
electrical components and other incompatible materials, and to restrict the rather
messy procedure to the smallest possible area.

The penetrant should be applied to the clean (and degreased) surface, using the
aerosol spray, a brush or by dipping or swabbing. The penetrant should be left on
the surface for the recommended contact time and, during this time, must be kept
wet.

If the penetrant dries on the surface (and in any crack) it will be extremely difficult
to remove and the whole area will have to be thoroughly cleaned before the
process can be re-attempted.

Note: If the parts are too hot, then premature drying is an obvious danger. Ideally
the temperature of the part should be in the range of 5C 40C.

Outside this temperature range, the application of the PFD procedure will require
care, because:

At low temperatures, metals sweat, and the resulting moisture will


contaminate the area, as previously stated
An increase in the viscosity of the penetrant, at low temperatures, will require
an increase in the dwell time

370280148.doc Issued March 2002 Page 29


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

Evaporation of the solvent (and the solvent carrier of the developer powder)
will be retarded during low temperatures. This will result in the blurring of
indications
At higher temperatures the evaporation rate is much shorter and will require
frequent wetting of the surface with penetrant to avoid it drying.

The time will usually depend on the temperature, the surface texture and the size
of the suspected defect. A time of 5 - 30 minutes is, normally, recommended.

The removal of the excess surface penetrant is another facet where incorrect
procedures will cause poor results. The object of the exercise is to remove all of
the surface penetrant without removing any of the penetrant that is in any defect.

In the past, operators have been known to spray penetrant removers directly onto
the surface, thus washing the penetrant out of the defect. The recommended
method, with solvent-based, spray removers, is firstly to remove the excess
penetrant with a clean, lint-free cloth (or paper wipe).

Next a small amount of the remover should be applied to a clean cloth and the
surface wiped with the moistened cloth (changing to a clean part of the cloth with
each wipe), until the surface is quite clean. Wiping should be done carefully and
in one direction only, to avoid over-wiping the area with the risk of wiping the
penetrant out of a defect.

The application of the developer is also a very critical stage of the PFD process
and demands a degree of skill on the part of the technician if small fatigue defects
are to be discovered.

Developers consist of either dry powders, or of the powder carried in a liquid.

Dry powder developers are applied by the use of puffers, electrostatic spray guns
or by using a dust storm cabinet.

Liquid-carried developer powders may be classed as:

Water-Soluble developers: where the fine particles are in solution with the
water in the same way as sugar dissolves in tea
Water-Suspended developers: where the fine particles are suspended in
water in much the same way as sand remains suspended in water and does
not dissolve
Wet (non-aqueous), solvent-based developers: where the microscopic powder
particles are suspended in a volatile solvent.

Page 30 370280148.doc Issued March 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

The dry powder developers and the first two wet types of developers are,
normally, confined to those establishments using the Type 1 penetrants, so
further consideration of them is not necessary in this topic.

The liquid in the In the Field PFD developer aerosol is, however, the same as
that in the solvent remover aerosol (Wet, non-aqueous). With this in mind,
extreme care must be taken when the developer is sprayed onto the inspection
area if the penetrant is not to be washed out of a potential defect.

Prior to applying the developer, the aerosol container should be shaken


vigourously so that the contents are agitated sufficiently to ensure that the
powder is thoroughly mixed with the solvent carrier liquid.

Holding the aerosol between 300 mm - 400 mm (12 in - 16 in) away from the
inspection surface, the developer is sprayed, in three or four very short bursts (of
approximately 1-second duration), with intervals (of approximately 6-seconds)
between each burst, to allow the solvent carrier to evaporate.

The aerosol should continue to be shaken during the intervals, to maintain the
powder in suspension and the result should provide a dusting of the developer
over the inspection area. The objective of the procedure is to produce a thin,
even coverage of the inspection area, - just enough to alter the surface
background colour - without giving a layer of such thickness which might
completely blanket the penetrant.

During the specified developer time the area should be monitored for indications
and, as previously stated, the inspection should be made, using the appropriate
quality of illumination. When using colour contrast penetrants it is recommended
that the area of the inspection should be illuminated (using daylight or artificial
light) to a level of at least 500 lux. This may be achieved with a fluorescent tube
of 80 W at a distance of 1 m (39.3 in) or with a tungsten filament pearl lamp of
100 W at 0.2 m (8 in).

Critical inspections may, however, demand higher levels of illumination and, as


always, the AMM or SRM will specify the precise requirements.

Indications of discontinuities (refer to Fig. 3) will need to be interpreted and


assessed for their effect on the serviceability of the part under inspection.

It is important that the exact position of any significant indication is recorded (with
the aid of a drawing or a photograph if required) because it might not be obvious
where the discontinuity is when the area is subsequently cleaned for repair or for
eventual return to service.

370280148.doc Issued March 2002 Page 31


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

Narrow Crack Very Fine Crack

Porosity
Wide Crack

Typical Penetrant Indications


Fig. 3

If there are no defects, then the area should be thoroughly cleaned. It is


imperative that all traces of the developer are removed because, being
hygroscopic, it will attract moisture, which could lead to subsequent corrosion
problems in the area.

It is recommended that, after the initial signs of the developer have been wiped
away, the area be liberally sprayed with the solvent remover which, on
evaporating, will leave the area in a clean and de-greased condition.

Restoration of the protective surface finish may involve etch priming, painting
and, possibly, additional anti-corrosive treatment. If, however, the area is to be
inspected regularly, it may be permitted to apply a coating of protective oil, grease
or inhibiting fluid between inspections.

There are many different brand names of penetrants, all of which must meet the
Process Specification DTD 929 (or MIL-I-25135-C), but the approved process will
always be specified in the relevant Aircraft Maintenance Manual.

There are available, Dual Mode penetrants, which exhibit both visible and
fluorescent capabilities. When viewed under white light they provide a contrast
with the developer and, when viewed under black light, they fluoresce. Another
type is the Thixotropic variety, which is a gel that only becomes fluid while it is
being brushed on a surface and has the capability of remaining in place on
vertical or on overhead surfaces. Special, non-oil-based, penetrants, and others
which are also low in sulphur, phosphorus and chlorine are used for the
inspection of oxygen system components, plastics and rubbers.

Page 32 370280148.doc Issued March 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

PAGE
INTENTIONALLY
BLANK

370280148.doc Issued March 2002 Page 33


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

17.5.4 Ultrasonic Flaw Detection (UFD)

This form of Non-destructive Testing is done by specially trained, and approved,


technicians, so only brief details of the background and the procedures are given
in this course. The student is, however, required to have a basic knowledge of the
principles of the techniques involved in Ultrasonic Flaw Detection (UFD).

UFD methods may be used to detect sub-surface defects in the majority of solid
materials. Ultrasonics can also be used to:

Measure the thickness of materials when it is only possible to get access to


one side of the component
Test for the delamination (de-bonding) of composite structures
Monitor real time cracking in spars and struts via Acoustic Emission methods.

The term, ultrasonic, describes sound oscillations at frequencies too high to be


detected by the human ear. Normal, healthy adults are, usually, able to detect
sound frequencies in the range between 20 Hz 20 kHz. For example, the lowest
note of a typical, full-size, piano vibrates at approximately 27.5 Hz, while the
highest note is in the region of 3.52 kHz. UFD procedures use sound frequencies
ranging from as much as 500 kHz to 25 MHz (and, sometimes, more).

Sound is caused by the sinusoidal oscillations of the particles in a medium and


the speed of sound is fixed in different materials, depending on their elasticity and
density. Table 1 shows the speed of sound through some common materials.

Table 1
SOUND VELOCITIES IN COMMON MATERIALS
Material m/sec ft/sec
Air (at 20C) 343 1,125
Water (at 20C) 1,480 4,854
Perspex 2,680 8,793
Pyrex Glass 5,640 18,500
Steel 5,900 19,351
Aluminium 6,350 20,827

Low-frequency sound travels outwards, from its source, and goes in all directions,
whereas the higher the frequency, the more the sound becomes unidirectional
until, at the extremely high frequencies employed in UFD, the sound can be
considered to be similar to a very narrow beam of light.

The principle of UFD is that a narrow beam of sound is introduced into a material
and the effects on that beam can indicate the structural state of the material.

Page 34 370280148.doc Issued March 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

The sound beams, used in UFD, are produced (and detected) by means of a
piezoelectric transducer (i.e. a device which converts electrical energy to
mechanical energy and vice versa).

A piezoelectric crystal (formerly quartz but, more commonly, man-made


ceramics such as barium titanate or lead zirconate titanate) is made to vibrate
when stimulated by electrical energy from the pulse generator of a cathode ray
tube (CRT) oscilloscope.

At the same time a pulse is generated across the time base of the oscilloscope.
The pulse repetition frequency (PRF) is set so that the time base of the
oscilloscope appears as a straight line.

When the transducer, mounted in a device known as the probe (refer to Fig. 4), is
applied to a material, the vibrations cause a narrow beam of ultrasonic waves to
be transmitted through the material.

Back
Initial Wall Pulse
Pulse Echo Generator

Time Base Probe


Controller Controller

X-plate

Amplifier
Y-plate Probe Couplant between
Back Wall Probe and
Inspection Surface
Component
under
Sound Beam
Inspection
and
Echo

Simplified UFD System


Fig. 4

In a similar manner to radar waves in air (and sonar waves in water) the sound
waves travel through the material until they meet an interface with a medium
which has a different acoustic impedance. The acoustic impedance of a material
is a function of the density of, and the velocity of sound in, the material.

370280148.doc Issued March 2002 Page 35


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

At the interface of different acoustic impedances the sound will be reflected (as
with the radar and sonar echoes) in proportion to their differences. It is usual for
the majority of sound to be reflected from an interface and the interface can be
caused by:

The far face (also called the back wall), of the component under inspection,
with the air on the other side
A crack or a void within the material (which will contain air or another gas)
An inclusion of a foreign body within the material (such as occurs in welds).

The reflected sound (or echo) returns to the transducer probe, where the energy
is converted into an electrical pulse, which is fed (via an amplifier) to the
oscilloscope. The amplified pulse causes a peak on the time-base, which is
calibrated so that the position of the peak represents the distance the reflected
sound has travelled in the material under inspection.

Because the transducer crystal is vibrating against the casing of the probe, a
great deal of sound is initially reflected within the probe. This is referred to as the
initial pulse (Americans refer to it as the main bang) and it is usually placed at
the extreme left of the time base, to act as the surface reference, and is not
considered as part of the search beam.

The face of the probe also creates an interface with the surface of the material
under test, due to the microscopic particles of air between them.

Because of the vast difference in the acoustic impedance of air compared to


other materials, most of the sound would not enter the material, unless a medium,
with a closer acoustic impedance to the probe and the material under test, is
interposed between them to act as a couplant. Typical couplants used are fluids
in the form of glycerine, silicon grease, petroleum jelly or medium-viscosity oils.

With this pulse/echo method, the location of a discontinuity in a component can


be quite accurately calculated. Unlike the PFD method, it is not only able to
detect subsurface flaws but also tight surface flaws which may be filled with oil,
grease, paint, rubber or any other contaminants which would create difficulties for
the PFD methods.

UFD has a greater versatility in that different modes of sound waves are utilised
to locate discontinuities occurring in various planes relative to the inspection
surface. Those modes of sound include:

Longitudinal or Compressional waves (also called Straight Beam testing)


Transverse or Shear waves (also called Angle Beam testing)
Surface or Rayleigh waves.

Page 36 370280148.doc Issued March 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

Because the narrow beams of sound obey some of the physical laws applicable
to light, with regard to reflection and refraction, it is necessary to employ
Longitudinal sound waves to locate discontinuities which are approximately
parallel to the surface which is being scanned by the probe (refer to Fig. 5).

Compressional Wave
Probe Initial Back Wall
Pulse Echo

(a)
)

(a) (b) (c)


) ) Echo from Flaw

Reduction of
Back Wall Echo
(b)
)

Total Reflection
from Flaw
with loss of
Back Wall Echo
(c)

Using Longitudinal Sound Waves


(Straight Beam Testing)
Fig. 5

Considering the light law, which states that, the angle of incidence is equal to the
angle of reflection it can be seen that the incident sound will be reflected back to
the probe when the maximum dimension of the flaw is in a plane parallel to the
scan surface.

In instances where flaws are oriented at angles which are either oblique or
normal to the scan surface, the sound would not be reflected directly back to the
probe and the flaws would be extremely difficult (if not impossible) to detect.

For the detection of these types of flaws it will be necessary to use Transverse
sound waves, to enable the sound beam to be reflected back to the transducer
crystal (refer to Fig. 6).

370280148.doc Issued March 2002 Page 37


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

Shear Wave
Probe

Using Transverse Sound Waves


(Angle Beam Testing)
Fig. 6

Again considering the laws associated with light, the crystal is angled in such a
manner that the Longitudinal waves are refracted out of the material under
inspection, leaving only Transverse waves for the search.

Note: By fixing the transducer to a more acute angle, it is also possible to refract
the waves in such a way that they travel along the surface of the material. In this
way Surface or Rayleigh waves may be generated, and used, to detect flaws
which are in, but which are normal to, the scan surface.

In very acoustic absorptive materials it may be necessary to resort to Through


Transmission or Pitch and Catch methods (refer to Fig. 7) where two probes are
used, with one being a Transmitter (Tx) and another a Receiver (Rx).

Tx
Tx Rx

Rx

(a) (b)
Through Transmission or Pitch and Catch Methods
Fig. 7

Page 38 370280148.doc Issued March 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

Using the Through Transmission methods will ensure that enough sound energy
is received to provide useful search information in materials which tend to absorb
great amounts of sound.

In Fig. 7 (a), it can be seen that two Compressional wave probes are being used,
where access to two opposite surfaces is possible, while Fig. 7 (b) shows two
Transverse wave probes being used, where access is only available to one
surface.

The disadvantage of the method, however, is that, while the existence of the flaw
can be detected (by the loss of the signal to the Receiver probe), unlike the pulse
echo method, the actual location of the flaw cannot be determined, because there
will be no peak on the time base to indicate its position.

As previously stated, UFD techniques can also be used to measure the thickness
(or the loss of thickness in the event of corrosion) of metals and most other
materials.

The de-bonding or delamination of composite structures can be achieved by


either the Through Transmission method (already described) or by means of the
Resonance technique.

This technique uses the fact that a material will vibrate at its maximum amplitude
when the sound is at the resonant frequency for a given thickness of that
material. Thus a certain thickness of properly bonded structure will vibrate at a
maximum amplitude at a specific frequency when an ultrasonic transducer is
applied to its surface.

The amplitude and frequency of the sound can be displayed on an oscilloscope


and, when the transducer passes over a de-bonded area, the loss of adhesion
will be detected as a change in thickness of the material. This results in a change
of amplitude and a shift in the frequency range on the oscilloscope, such that the
de-bonded area can be quite easily located.

Acoustic Emission techniques involve the placing of piezoelectric transducers at


critical positions on spars or struts and the monitoring of the sounds being given
out as a crack propagates through the metal.

The information is electronically processed and, through appropriate circuitry, can


be linked to recording devices or real time warning lamps to indicate the
progress and severity of the cracking or wear in the particular structure.

370280148.doc Issued March 2002 Page 39


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

17.5.5 Eddy Current Flaw Detection (ECFD)

ECFD procedures are, normally, restricted to specially trained and approved


personnel but there may be instances where (in aircraft wheel servicing bays for
example) locally trained technicians are approved either to do limited and
uncomplicated procedures or to monitor automated ECFD equipment. For these
reasons it is necessary for the student to understand the fundamentals of ECFD
and the techniques involved in its application.

Flaw detection procedures, utilising eddy currents, are employed on electrically


conductive materials (metals) and are capable of detecting:

Surface and (to a limited degree) subsurface cracks: which may be closed by
metal flow, oil, paint, rubber or other contaminants
Variations in the thickness of metal skins: due to internal corrosion of closed
areas, to which normal access is difficult (or impossible) due to time/expense
constraints
Changes in the electrical conductivity of metals: through incorrect heat-
treatments or fire damage
Cracking emanating from rivet and bolt holes in aircraft skins and structures.

Eddy currents are alternating electrical currents, which are induced, into a
conductive material, by an alternating magnetic field. They circulate in the
material in a plane normal to the field, which produces them.

The basic principle is that a probe (refer to Fig. 8), consisting of a small coil,
which is tightly wound around a ferrite core and supplied with alternating current
(ac), is held in contact with (or in close proximity to) the surface of the component
under inspection.

ac Supply Ferrite Core

Alternating Magnetic
Field around Coil

Conductive Material
under Inspection Induced Alternating
Electrical Currents

Principles of ECFD
Fig. 8

Page 40 370280148.doc Issued March 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

The magnetic field, associated with the current flowing in the coil, is concentrated
into a small area by the ferrite core of the probe. When the probe is placed on the
surface of the metal, the alternating magnetic field couples with the metal and
induces alternating electrical currents into the metal.

These induced electrical currents circulate in the metal in a plane normal to the
probes coil and, as they are electrical currents, flowing in a conductor, they will
also create magnetic fields in the metal.

In accordance with Lenzs Law, the induced magnetic fields will oppose the field
which produces them, and, in so doing, will modify the coils magnetic field, which
hence, affects the electrical impedance of the coil.

Any event that changes the value of the induced eddy currents will, subsequently,
cause a change in the impedance of the coil. If the coil is included in a bridge
circuit (refer to Fig. 9), within an inspection instrument, which is provided with a
suitable indicating device, it will provide an indication of the condition of the
component under inspection.

L1 L2

Set Zero
Control

P1 A P2
Sensitivity
Control

L3

L4

Simplified ECFD Impedance Bridge Circuit


Fig. 9

370280148.doc Issued March 2002 Page 41


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

Using the Wheatstone Bridge principle (where the coil is one of the inductances),
when the ratio of L1 : L2 equals the ratio of L3 : L4, the bridge will be in balance
and the voltages at points P1 and P2 will be equal. The indicating meter will show
zero, because no current is flowing through it.

If the probe is now placed on a metal surface, the induced eddy currents will
change the value of L4 and cause an imbalance of the bridge. The voltages at P 1
and P2 will be different and a current will flow between them. The meter will show
an indication of the current flow.

The variable inductance L1 is adjusted to regain the balance of the bridge, so that
the meter, once more, is set at zero and the probe is moved over the inspection
area. The function of the sensitivity control will be explained a little later.

Any factors, which alter the value of the induced eddy currents in the inspection
area, will result in an indication on the meter.

Factors, which affect eddy currents in a metal (and require careful interpretation),
include:

Conductivity
Permeability
Frequency
Proximity
Probe Handling
Discontinuities.

A change in the conductivity and the magnetic permeability of the metal will
obviously influence the induced current flow and subsequent magnetic fields.

The frequency, at which the driving current of the probe coil alternates, will
govern the quality of the induced current and influences the depth of penetration
of the eddy currents into the material.

The higher the frequency of the coil current, then the closer to the surface of the
material the eddy currents remain. This is referred to as the skin effect.

High frequencies of ac are used to drive the coils when searching for fine fatigue
cracks in the surface of metals, while low frequencies are employed for the coils
of the probes used to detect sub-surface defects.

Incidentally, an increase in conductivity, or permeability, will also result in a


decrease in the depth of penetration, of the eddy currents, in the material under
inspection.

Page 42 370280148.doc Issued March 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

The proximity of the probe to the surface affects the induced currents and this
phenomenon can be used to provide a coating thickness measurement.

With the probe placed on a bare metal test specimen, the inspection meter
indicator is set at zero. Known thicknesses of plastic films are then gradually
interposed between the probe and the metal.

As the thicknesses increase, the amount of lift off will be indicated on the meter
and these indications can be used to compare with readings, obtained when the
probe is positioned on a painted surface of similar metal, to provide a
measurement of the coating thickness.

Probe handling is also very important and the probe should be maintained at a
constant angle to the search surface (preferably normal to the surface). To ensure
this, probes are often mounted in purpose-made shoes, which conform to the
surface under inspection (particularly in wheel flanges and bead seat areas) to
maintain the correct angle of the probe with the surface.

Discontinuities will, of course, cause a change in the induced eddy currents but
the type (and severity) of flaws cannot be deduced unless the equipment is
properly calibrated before (and during) the inspection procedure. In order to
calibrate the equipment, standard reference pieces, manufactured from a material
similar to that being tested, are necessary.

Aluminium alloy skins, used for engine cowlings, will be affected by exposure to
elevated temperatures (up to approximately 500C) and the resulting heat-
treatment will cause the material to be below strength, with obvious implications.

Above this temperature, signs of heat damage, such as melted or charred metal,
will become apparent but, below the temperature, the damage is not easily seen.

Conductivity changes in the skins, caused by the heat, can however be detected,
using ECFD procedures, and below-strength areas identified for subsequent
repair or replacement.

A Conductivity Meter and a surface probe are used for this particular procedure
with the meter being calibrated on materials with known levels of conductivity.

The meter, in this procedure, registers relative conductivity as a percentage of the


International Annealed Copper Standard (% IACS) where commercially pure
copper is set at 100% and the conductivity of other alloys, containing copper, is
compared to it.

Silver, which is a better electrical conductor than copper, is considered to have a


relative conductivity of approximately 106 % IACS.

370280148.doc Issued March 2002 Page 43


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

Corrosion of the internal surfaces of aircraft skins can be detected, without resort
to time-consuming (and expensive) internal trim removal, and stripping, by the
use of low frequency ECFD procedures.

When searching for corrosion on the remote surface of a single layer skin, a
typical calibration standard might be a simple step wedge (refer to Fig. 10).

Step Wedge
Calibration Standard

Step Wedge used for Corrosion Detection


Fig. 10

The probe frequency would be set so that the eddy currents penetrate the full
depth of the thick layer (which represents the correct thickness of the skin) and
the instrument is zeroed with the probe on the thick layer. The probe is next
moved onto the thin part of the wedge and the sensitivity control adjusted to give
the required indication.

Following calibration, the probe is moved onto the inspection area and a series of
parallel scans made. Any significant indications are noted and recorded for
appropriate action.

For inspections, searching for corrosion in the remote surfaces of multiple layers
of skins (such as is found in the lap and butt joints of fuselages), it is then
necessary to use a calibration standard with the appropriate number of skins.

The frequency of the probe would be adjusted (lowered) to provide the required
depth of penetration in each plate being inspected.

Low frequency probes may also be used to detect cracks emanating from the
rivet holes of multi-layered skins.

Specially constructed doughnut (or ring) probes, which have a clear, plastic
centre, to facilitate accurate placement of the probe over the rivet heads, are
used in these procedures.

Page 44 370280148.doc Issued March 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

Low frequency probes operate in the 100 Hz to upper kHz range, while high
frequency probes are driven at frequencies of 5MHz (or more) and have a much
greater sensitivity, due to the highly concentrated eddy current field at such
frequencies.

High frequency probes are used in the search for fine fatigue cracks in the
surfaces of metals typically used in aircraft structures and components. They are
particularly useful for the inspection of such critical items as:

Propeller Blades (both the ferrous and the non-ferrous metal types)
Compressor and Turbine blades (and guide vanes) of gas turbine engines.
Wheels and Landing Gear struts
Window and Door surrounds
Front and rear Pressure Diaphragms of pressurised aircraft fuselages

The inspections of these items are achieved with small, portable, battery-
operated machines or with automated installations housed in servicing bays or
workshops.

A calibration standard for the detection of fatigue cracks would necessitate either
a previously failed component with a known defect or (typically) a sample of the
relevant metal, containing spark eroded, simulated defects (refer to Fig. 11)
against which to calibrate the machine.

The probe is placed on unflawed material and the meter zeroed before moving
the probe over the appropriate slit and adjusting the sensitivity control to provide
the specified level of sensitivity for the inspection procedure.

Slit Depths
Three Spark Eroded Slits
(0.2 mm Wide) 0.2 mm

0.5 mm

1.0 mm

Metal of Similar Specification to


Area under Inspection

Typical High Frequency EFD Calibration Standard


Fig. 11

370280148.doc Issued March 2002 Page 45


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

Inspections, of critical bolt holes, are achieved by the use of a (high frequency)
hand-held, bolt hole probe. Where large numbers of bolt holes are involved, use
is made of a specially designed probe which is attached and rotated by a low
torque machine resembling an electric rotary drill.

The machine is connected to a CRT oscilloscope, which analyses the phase


difference of the changing eddy currents and displays them as lissajous curves
(also called flying dots) on the CRT screen.

Phase analysis machines provide much more information regarding the cause of
the change in the induced eddy currents and are able to discriminate between the
various factors (i.e. changes in conductivity, permeability, geometry etc.),
whereas the simple impedance change machines cannot.

Phase analysis machines can accurately differentiate between the signals


received from corrosion, cracks and scores (and even a crack in the bottom of a
score!) such that the trend has moved towards the use of computer-controlled
phase analysis machines for all but the most simplest of EFD procedures.

17.5.6 Magnetic Particle Flaw Detection (MPFD)

MPFD techniques (in the aerospace industry) are restricted to qualified NDT
personnel, usually working in purpose-designed workshops. It is a requirement,
however, that the student is aware of the fundamental principles and the
applications associated with this method of inspection.

As the title implies, MPFD procedures are employed on components and


structures which are capable of being magnetised. The procedures are used to
locate both surface and sub-surface discontinuities in ferromagnetic metals.

The principle involves the setting up of a magnetic field in a component such that,
if a discontinuity disrupts the lines of magnetic force (flux lines), the resultant flux
leakage (refer to Fig. 12) will create local North and South magnetic poles on the
surface of the component.
Flux Leakage
(Highly Magnified for Clarity)
Flux Lines
S N

N S

Magnetic Flux Leakage


Fig. 12

Page 46 370280148.doc Issued March 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

The flux leakage may be caused by internal flaws, such as inclusions, or by


extremely tight fatigue cracks on the surface of the component. Both types of
defects would be impossible to see with the naked eye but, when a powder,
consisting of finely divided ferromagnetic particles, is applied to the surface of the
component, the tiny particles will be attracted to the site of the flux leakage and
will provide a visible indication of the discontinuity.

To aid detection, the powder may be coloured red, grey, yellow or black (or any
colour which provides the best contrast against the inspection surfaces finish).

Black is the most common colour and, while powders may be applied dry, by
puffers or by sprinkling, the particles are normally suspended in a light oil (usually
kerosene), to assist their movement to the flux leakage and (as opposed to using
water as the carrier) to minimise the onset of corrosion.

The resulting blackened fluid has earned the name of magnetic ink, but this term
is used to describe all of the liquid-carried powders, regardless of their colour.

Magnetic inks are also available whereby the particles are treated with powerful
fluoro-agents so that, in a similar manner to the fluorescent PFD procedures, they
can be viewed under black light, to provide superior sensitivity to flux leakages
when inspecting Class 1 aerospace materials.

Note; Flux leakages can also be caused by abrupt changes of geometry, such as
corners, small radii and screw threads. It, thus, demands that great care is
needed in interpreting the indications obtained with MPFD procedures and
requires that personnel applying the procedures receive appropriate training.

There are various methods of establishing a magnetic field in components but


they, basically, fall into the two categories of:

Magnetic Flow procedures


Current Flow procedures.

The choice of method depends on the geometry of the part under inspection and
the expected orientation of any flaw.

Maximum sensitivity for flaw detection is obtained when the flaw is normal (90)
to the direction of the lines of flux. Sensitivity is not, however, too greatly reduced
when flaws lie at angles up to 45 from the optimum angle but, beyond 45,
sensitivity reduces appreciably.

For these reasons, complete inspection of a surface will require that the magnetic
field be established in at least two directions, mutually at right angles (in separate
applications), to ensure full coverage of the area under inspection.

370280148.doc Issued March 2002 Page 47


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

Establishing a magnetic field, in a component, using Magnetic Flow (MF)


procedures (refer to Fig. 13) involves the use of:

Permanent Magnets: using conventional, portable, U-shaped or horse-shoe


magnets of varying sizes, depending on the strength of magnetic field
required.
Electro-magnets: or Yokes (once again portable and hand-operated devices),
with articulating legs, which can be adjusted to accommodate components of
different shapes and sizes.
Purpose-built installations: used in workshops and consisting of
electromagnetic machines, with adjustable heads, between which
components are clamped so that the magnetic flux flows from one head to the
other and through the component under inspection.
ON/OFF Switch

ac/dc Supply

Articulating Legs

Flux Lines
Flux Lines
Discontinuities
Discontinuities

(a) (b)
Permanent Magnet Electromagnetic Yoke

Flux Lines Discontinuities Component under Inspection

Fixed Head Adjustable Head

(c)
Simplified MF Installation

Magnetic Flow Methods


Fig. 13

Page 48 370280148.doc Issued March 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

Electrical current, used for the electromagnetic methods (portable types or the
fixed installations), can be either ac, or half- or full-wave rectified ac. It may also
be provided from a bank of dc batteries. The type of current used will depend on
the types of defects, which are being sought, and the metal involved.

Sub-surface defects will be detected using dc, or rectified ac, to provide magnetic
fields which penetrate to different levels below the surface of the metal (straight
dc penetrates the deepest).

Unrectified ac, in a similar manner to high-frequency ECFD methods, will create a


skin effect and is used to locate fine fatigue cracks on the surface of high-grade
steel alloy parts.

Establishing a magnetic field, in a component, using Current Flow (CF) methods


involves the previously-described electrical sources and the use of:

Direct methods: whereby the electrical current is passed directly through the
component under inspection
Indirect or induced methods: which involve the use of rigid rods or bars of
metal or lengths of flexible, heavy duty (welding grade) cable, through which
the various types of previously-mentioned currents may be passed.

With direct methods of CF inspections it is essential that good electrical contact


be achieved between the current-carrying electrodes and the surfaces of the
component under inspection, in order to avoid damage from arcing or burning.

While direct methods may be used in situ on aircraft structures they are more
commonly used in workshops, by qualified personnel, using purpose-built
installations, with adjustable heads (similar to the MF installations). The parts are
clamped between the heads and, in this instance, the specified electrical current
is allowed to flow through the component (refer to Fig. 14).
Flux Lines Discontinuities

Simplified CF Installation
Fig. 14

370280148.doc Issued March 2002 Page 49


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

Both the CF and the MF installations are, in fact, contained in one machine, with
the capability (through circuit switching) of selecting either current flow before
applying magnetic flow or vice versa, depending on the technique requirements.

When current flow is applied to the component, a magnetic field is set up in (and
around) that component, in a direction normal (90) to the direction of the current.

This transverse (or circular) magnetic field will also be at right angles to the field
created by the subsequent (or previous) magnetic flow procedure.

Once again, maximum sensitivity for flaw detection will be at 90 to the magnetic
field (or in the direction of the applied current!) with a lessening of sensitivity up to
45 from the optimum direction.

Using such installations, with both CF and MF capabilities, allows full coverage of
the inspection area and, thus, maximises the possibility of locating potential
defects in critical components.

The parts must always be de-magnetised before, between and after all MPFD
inspections. This ensures that there are no interfering or spurious fields within the
parts before and between each application.

Demagnetisation also allows easier cleaning after the inspection, when the low-
retentivity magnetic particles will be able to be cleaned from the demagnetised
parts.

Additionally, demagnetisation must be performed after the inspection, to ensure


that the parts will not affect magnetic compasses or attract metal swarf (from oil
or fuel systems etc.) which could cause damage when the parts are reinstalled in
their respective locations.

One of the indirect or induced methods of CF inspections takes advantage of the


fact that an insulated metal rod may be threaded through annular or cylindrical
components (refer to Fig.15).

When current is passed through the central conductor (also called a threading
bar), the associated magnetic field couples with, and enters, the component. The
induced (circular) magnetic field will allow defects to be detected in the inner and
outer walls of the component in addition to indicating any flaws in the end
surfaces.

Maximum sensitivity will, again, be in the direction of the current flow in the
central conductor and normal to the circular magnetic field which is induced into
the component.

Page 50 370280148.doc Issued March 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

Direction of Induced Flux Discontinuities


Insulation around Threading Bar

Direction of Current Flow


through Threading Bar

Central Conductor (Threading Bar)


Fig. 15

Another of the indirect or induced methods of CF inspections entails the use of


heavy-duty, insulated cable, formed into coils (e.g. 4 6 turns for ac), which may
be wrapped around the component under test (refer to Fig. 16).

When current is applied to the coil, its associated magnetic field will couple with
the component and, in this instance, a longitudinal magnetic field will be induced
into the component. Maximum sensitivity for flaws will, of course, be normal to the
longitudinal magnetic field and in the direction of the current flow in the coil.

Flux Lines

Discontinuities
Current Flow through Coil
Close-Fitting or Wrapping Coil
Fig. 16

Coils may also be used in a similar manner to threading bars, where a one- or
two-turn coil may be threaded through the lug of a landing gear strut, for example,
to search for stress cracks emanating from the centre of the lug.

370280148.doc Issued March 2002 Page 51


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

Larger, rigid or aperture coils are used in workshop situations, where the
component under inspection is laid in the coil and the resulting longitudinal
magnetisation will assist in revealing flaws in the component.

The aperture coils are also the most commonly used methods of achieving the
demagnetisation of components, before, between and after MPFD inspections.

When ac is being used, the component is placed in the coil and, while the current
is applied, the component is slowly withdrawn (maintaining alignment with the
coils axis) to a distance of approximately 1.5 m (5 ft) from the coil.

Demagnetisation may also be achieved, in an ac coil (and, incidentally, by all the


other methods using ac to generate the magnetic field), by gradually reducing the
value of the current while the component is lying in the coil.

Where dc supplies are used to energise coils, there is usually a capability of


reducing the amperage in specified increments whilst the direction of the current
is alternately switched. This form of demagnetisation is the most thorough as the
dc-induced field penetrates deepest in components under inspection.

Following demagnetisation a confirmatory test is made, using a special flux meter


(or a suitable magnetic compass) before the component is thoroughly cleaned of
all traces of magnetic ink.

Components should then be stored away from all magnetic sources and any
surface protection restored while awaiting reinstallation, repair or replacement.

17.5.7 Radiographic Flaw Detection (RFD)

Because the misuse of radiographic equipment could result in the release of


physically harmful (ionising) radiation, operators must be trained and aware of the
many safety regulations and codes of practice associated with these procedures.

Aircraft RFD inspections are, therefore, only done by qualified NDT personnel
from organisations approved under BCAR A8, and who are nationally registered
as radiation workers. These workers are subject to frequent medical checks and
wear sensitive film badges to detect any radiation dosage to which they may
become exposed. Should the dosage exceed stringent limits, then the worker is
withdrawn from tasks involving ionising radiation.

Interpretation of radiographic images is also very important, as incorrect


conclusions could result in the acceptance of unserviceable structures or,
conversely, in the scrapping of safe structures.

Students are, however, required to have knowledge of the fundamental principles


of RFD and its applications in aerospace inspections.

Page 52 370280148.doc Issued March 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

Due to the hazards of radiation, it will be necessary to isolate the aircraft and to
keep personnel at a safe distance from the inspection area. The area should be
roped off, with radiation warning signs (a black trefoil against a yellow
background), clearly shown. Flashing lights and horns (or klaxons) are also
employed to signify that ionising radiation sources are in use in the area and that
unauthorised personnel should keep away.

The main sources of ionising radiation, used in aerospace RFD procedures,


involve the use of either X- or Gamma-ray emitters. Both rays have the ability to
penetrate materials, which cannot be penetrated by visible light and are identical
forms of energy in the electromagnetic spectrum (refer to Fig. 17).

Their difference lies only in the way in which they are generated and the names
given them by the scientists who discovered them.

Radar Infra-red UV Rays


Radio Rays White
TV Light

X & Gamma Cosmic


Rays Rays

1m 0.01 m 100 m 1 m 10 nm 0.1 nm 10 -3 nm 10 -5 nm 10 -7 nm

10 m 0.1m 0.001 m 10 m 100 nm 1nm 0.01 nm 10 -4 nm 10 -6 nm

The Electromagnetic Spectrum


Fig. 17

X-rays are electrically produced in a cathode ray tube, (refer to Fig. 18) which
accelerates electrons, released at the cathode, towards a dense metal (tungsten)
target which is embedded in the anode.

The amount of electrons, freed at the cathode, is controlled by adjustment of the


tube current, which is measured in milliamps (mA). The force of the collisions
and, hence, the penetrating power of the X-rays, is controlled by the potential
difference between the cathode and the anode. The tube voltage is measured in
kilovolts (kV).

Typical aerospace RFD procedures use machines generating X-rays in the range
of 10kV to 250kV, depending on the penetrative power required.

370280148.doc Issued March 2002 Page 53


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

Potential Difference (kV)

Free Electrons
Cathode -ve Anode +ve

Tube Current (mA)

Tungsten Target
Evacuated Glass
set in Copper Anode
Envelope
X-Ray Beam

Simplified X-Ray Tube


Fig. 18

On striking the target, the electrons collide with the atomic particles of the
tungsten and the resulting energy exchange is released as heat, light and a small
percentage of packages (photons) of energy. A large copper anode, in which the
target is mounted, dissipates the heat, generated by the electron stream. The
anode and the glass envelope are, in turn, cooled by circulating gas, oil or water
being pumped around them.

The amount of light is confined to a dull red glow at the target and is insignificant.

The photons, however, behave in a similar manner to rays of light in that they
travel in straight lines. They also obey the inverse square law in that, as they
travel from the source, their area of incidence increases but their intensity
decreases in a ratio to the square of the distant from the source.

One important safety aspect is that X-rays are generated electrically and, hence,
can be switched off, either automatically, by a timer switch, or manually, by the
NDT person at the control panel.

Gamma radiation is the name given to the photons of energy which result from
the atomic collisions occurring during the disintegration of radioactive isotopes.

An isotope is an element, the nucleus of which gains or loses particles such that
the atomic weight changes though the chemical properties remain unchanged.

The naturally occurring isotopes of many elements are quite stable in their
changed state, while others become unstable and, in attempting to regain a
stable state, emit photons of energy (become radio-active) due to the nucleic
particle collisions. Gamma radiation cannot be switched off (it can only be
shielded) and continues until the element reaches a stable condition.

Page 54 370280148.doc Issued March 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

Gamma radiation sources, used in RFD procedures, include artificially created


isotopes such as Cobalt 60, Iridium 192 and Ytterbium 169 (the number following
the element name is the atomic weight or relative atomic mass of the isotope).

As previously stated, Gamma rays can exist over similar wavelengths as X-rays
with similar properties but, generally, the Gamma rays, emitted by the commonly
used radio-isotopes, have a greater penetrative power.

Their power does, however, decrease with the passage of time as the isotope
attempts to gain a stable state. The decrease in power over time is referred to as
the half value period (also called half life) and is a measure of the time when
the activity of the isotope will decay to half that of its original or former value.

Table 2 shows some typical radio-isotopes, their penetrative power (compared to


X-rays), the metal thicknesses through which they can penetrate and their half
value periods.

Table 2
Gamma-ray Sources Compared to X-ray Generators
Radio- Penetrative Power Thickness of Metal Half Value
Isotope (compared to X-rays) (capable of penetrating) Period
Ytterbium 169 0.15 0.40 MeV 2 mm 30 mm Steel 32 days
Iridium 192 0.31 1.20 MeV 6 mm 100 mm Steel 74 days
Thulium 170 0.083 0.96 MeV 2 mm 12 mm Aluminium 134 days
Cobalt 60 1.17 1.33 MeV 50 mm 200 mm Steel 5.3 years
Caesium 137 0.66 0.67 MeV 25 mm 100 mm Steel 26.2 years

The advantage of using a radio-isotope as opposed to an X-ray machine lies not


only in the fact that the penetrating power is superior but also the equipment is
less bulky than the X-ray machines and there is no requirement for a mains
electrical supply. The radioactive source is usually so small that it can be placed
inside objects such as engine shafts, using small diameter, flexible guide tubes.

The disadvantages in their use is the need for greater protection measures,
involving larger isolation areas, and the possibility of longer exposures as the
isotopes decay in strength with the passage of time. Another drawback, and
particularly so with the more powerful Cobalt 60 source, is that the resulting
radiographs tend to be less sensitive than those created with low-power X-rays.

The radiograph is produced when the appropriate radiation source is directed at


the components under inspection and a light-proof envelope (or cassette),
containing a sheet of radiographic film, is placed on the remote side of the
component (refer to Fig. 19). Depending on the size of the inspection area there
may be several sheets of film envelopes, placed simultaneously, to provide
adequate coverage at one exposure.

370280148.doc Issued March 2002 Page 55


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

Radiation Source
(X- or Gamma Rays)

Metallic
Step Wedge

Plastic Film Base


(Emulsion on Both Sides

Production of a Radiograph
Fig. 19

The films, used in radiography, are very similar to those used in photography
except that the emulsion is applied to both sides of the transparent, plastic base.

The emulsion contains microscopic grains of silver halides, which are sensitive to
the photons of energy (and light). When exposed to the rays, a change takes
place in the silver particles such that, when the film is developed and fixed, they
turn into different degrees of dark metallic compounds, depending on the amount
of radiation they have received.

The silver which has not received radiation is unaffected and is washed away in
the developing and fixing processes. A negative-type image of the component is
thus formed, the darkness (density) of which depends on the quantity of radiation
passing through the specimen. The thicker the specimen, the more radiation it will
absorb and, consequently, it will provide a lighter (less dense) image.

The accurate interpretation of defects, indicated on a radiograph, requires a great


deal of skill and a good knowledge of the aircraft structure.

Without the knowledge it would be easy for the NDT technician to overlook faults
such as distorted or missing parts. Even the presence of leaded fuel in the tank of
a piston-engined aircraft can mask defects. The interpretation may be simplified if
radiographs of serviceable structure are available for comparison.

Page 56 370280148.doc Issued March 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

Radiographic inspections are often done during the manufacturing stages, to


check for such faults as:

Metallurgical defects in castings and welds: these produce patterns


recognisable by an experienced viewer. Porosity will reduce the amount of
material through which the rays must pass and a darker image will result
Cracks in welds: these are difficult to detect, as the angle at which the
radiograph is taken is important. The source should be absolutely normal to
the direction of the suspected crack.

Typical RFD procedures, done during routine aircraft maintenance, include the
search for:

Corrosion: this will show up as a fuzzy image, but the presence of paint and
jointing compound will make it difficult to detect. Inter-granular corrosion may
not be detected until it has reached an advanced state and affects the metal
surface. A corrosion pit, where there is a change in thickness, is more readily
detected
Cracks: stress cracks often run along a line of rivets, but the edge of jointing
compounds, used during the wet assembly of riveted joints, often gives a false
indication. Radiographs may show indications of cracks, which, eventually, are
found to be cracks in tank sealant. It is sometimes possible to open up cracks,
before inspection, by applying a tension load by jacking
Loose articles, riveting faults and poor assembly techniques
Levels of fluids in accumulators and the presence of water in composite
materials.

17.5.8 Miscellaneous Radiation Techniques

Other techniques, which involve the use of radiation of one type or another,
include:

Fluoroscopy: using either of the previously mentioned sources the standard


sheet film is replaced by a fluorescent screen. This enables moving images to
be captured. For safety reasons a video camera is focused on the screen and
the image viewed at a safe distance. An example of 'fluoroscopy' is where
oscillation in a turbine shaft of gas turbine engine being 'run' can be observed.
A more common example of its use is provided by the low-energy X-raying of
luggage, at airport departure security 'check-ins'

Thermography: using heat radiation, a heat-sensitive camera is used to


inspect areas of aircraft in particular composites. In the passive mode the
aircraft is inspected shortly after landing and temperature 'cold' spots will
indicate de-lamination or osmosis. The active mode consists of microwave
radiations being targeted at suspect components with the area being
inspected by the camera in the same way as the passive mode.

370280148.doc Issued March 2002 Page 57


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

17.6 Disassembly and Re-assembly Techniques

Disassembly and re-assembly, in the terms of aircraft, can cover a range of


activities from complete airframes down to component maintenance, with several
steps in between. The reasons for dismantling and re-assembly may include:

Complete airframe disassembly for road/air shipment


Replacement of major components/modules
Replacement of minor components/modules
Disassembly & re-assembly of major components
Disassembly & re-assembly of minor components

17.6.1 Complete Airframes

It may be necessary to dismantle a complete aircraft for the purpose of


transportation by road or by air. This could be for recovery from an accident site,
remote from the airfield or for movement of the aircraft when it is totally non-
airworthy, due perhaps to severe corrosion or an unknown maintenance history.

Because many larger, modern aircraft are manufactured at several different


locations, the completed modules are assembled in the final build hall of the
primary manufacturer. The joining points are often known as transportation
joints, and, in extreme instances, can be the points where the aircraft may be
dismantled again to allow transportation (refer to Fig. 20).

Typical Manufacturers Joining Points


Fig. 20

Page 58 370280148.doc Issued March 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

The instructions for the dismantling operation will be found either in the aircrafts
Maintenance Manual or in a special dismantling procedure, issued by the
manufacturer. During the dismantling operation, precautions must be taken to
prevent injury and damage.

General precautions would include such items as:

The aircraft should, if at all possible, be dismantled within a hangar. If this is


not possible, then level and firm ground will suffice
Sufficient clearance in the hangar must be available, both to clear the airframe
when on jacks, and to allow heavy lifting cranes enough room to manoeuvre
over the aircraft
All precautions, in accordance with the manufacturers instructions, must be
taken prior to the aircraft entering the hangar; such as de-fuelling and the
removal of devices such as emergency oxygen canisters
When the aircraft is jacked-up, all trestles must also be placed in position.
This allows the aircraft to be climbed upon and, later, ensures that it will not
overbalance when a major part (such as a wing), is removed.

Whilst the manufacturers instructions will give the details for a specific aircraft,
the following sequence of dismantling gives an idea of the correct order of
disassembly:

Main planes
Tail unit
Undercarriage units
Centre section
Fuselage.

Re-assembly is in the reverse order of disassembly, and all parts must be


cleaned, protected and serviceable, prior to their installation.

17.6.2 Replacement of Major Components/Modules

This type of operation will normally be completed at a large maintenance base,


where all the required equipment is available. An example could be the
replacement of a wing that has suffered major damage.

Other types of similar work might be the replacement of damaged wing tips,
empennage surfaces and nose cones. If the aircraft is at an outstation when the
damage occurs, confirmation should be sought as to whether the aircraft can be
flown back to base for repair, or repaired where it is.

370280148.doc Issued March 2002 Page 59


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

17.6.3 Replacement of Minor Components/Modules

Some components have to be repaired by replacement. Repairs to flying control


surfaces, for example, are often done in a repair bay. The component may be
replaced on the aircraft by a serviceable item, or reinstalled once the repair in the
bay has been completed.

Other components, which are replaced first and repaired later, might include
some structural items such as doors of all types, and most fairings and cowlings.
Most of these tasks are simple removal and replacement operations that are
covered in the AMM.

17.6.4 Disassembly and Re-assembly of Major Components

Most of the work done, during this phase of maintenance, is scheduled in with
normal aircraft maintenance. The components may not only be removed and
reinstalled at different times during the maintenance, but work will also be done
on the items whilst they are removed. They may also be removed to allow access
to other parts of the airframe during the maintenance.

Items such as engines, propellers, landing gears and wheels require some form
of maintenance. This may include a simple condition check, or a full overhaul of
its component parts, allowing checks on internal component parts for wear,
damage and corrosion.

The full procedure for this type of work will be carried out in accordance with the
CMM. This book will give all the operations required to dismantle the component
and will advise what to look for whilst the item is undergoing maintenance. It will
also state the re-assembly method, including the fitting of new parts such as
seals, gaskets, oil and other consumables that have to be replaced, during
overhaul.

17.6.5 Disassembly and Re-assembly of Minor Components

A typical passenger aircraft can contain hundreds of small components that work
together as parts of a larger system. This can include a wide range of hydraulic
and pneumatic components that can be mechanical, electromechanical or
electrical in operation.

Other components might include those installed into fuel, air conditioning,
pressurisation, electrical and electronic systems. These components have their
own CMM to allow maintenance and trouble-shooting to be done. Some
components are only removed once they fail (On-Condition), while others receive
regular maintenance.

Page 60 370280148.doc Issued March 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

Instruments, electric and electronic components can be dismantled and serviced


by the aircraft operator. It normally requires the use of a dedicated overhaul
facility, which can provide the correct environmental conditions and is equipped
with the special test equipment required to carry out maintenance and repair.

Operators of smaller aircraft, or those who operate only a few aircraft, will usually
send components requiring repair or maintenance to a third party maintenance
organisation. This company will have the special facilities, equipment and
personnel, to complete the required work on components from a number of
different customers.

17.6.6 Basic Disassembly and Re-assembly Techniques

All of the previously mentioned procedures require the use of the correct
techniques over a wide range of working practices. These techniques will ensure
that the components are removed, dismantled, re-assembled and re-installed in
accordance with both the relevant manuals and using the correct standard
practices.

An AMM and CMM dictate the correct type and size of locking wire or split pin to
be used during overhaul or maintenance of a component. These publications also
stipulate exact detail of items such as the lock wire angle of approach and the
correct positioning of a split pin. AMM chapters 20 and 70 list the standard
practices that should be used during overhaul.

Other locking devices include items such as single tab washers, shake-proof
washers, circlips and locking rings. Some can only be used once only whilst
others are re-used provided they are still serviceable.

The replacement of spring washers is advised during overhaul and repair,


especially on engines and pumps. Other devices used for locking or holding
fasteners in position, such as multi-tab washers and locking plates can normally
be reused.

Stiff nuts with fibre or nylon inserts can be checked to ascertain if a certain
degree of stiffness is still available. If the nut can be run along a thread by hand it
should be replaced. They should not be used in high temperature areas.

In all matters relating to aircraft, the manufacturer has the final say on which
fasteners can be reused and which must be replaced.

Because friction is essential to keep the fasteners secure, sometimes it is


necessary to do a torque check on the bolt/nut combination, in order to confirm
their continuing serviceability. This is especially true of all metal fasteners that
can normally be re-used.

370280148.doc Issued March 2002 Page 61


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

The majority of nuts, bolts and set-screws, on an aircraft, are subject to a


standard torque value. This depends on their material, finish, lubrication, thread
type and size, although the manufacturers torque value will be the correct one to
use.

The correct torque loadings are normally applied using a torque wrench that has
been previously calibrated to the correct value. In some special instances, pre-
load indicating (PLI) washers may be specified.

When assembling any component or major airframe part, the manufacturer will
specify whether the torque value is lubricated or dry. Lubricated values are
measured with the threads and all mating surfaces lightly lubricated with oil,
sealant or anti-seize compound as appropriate.

When assembling some components, it may be vital that certain alignments,


dimensions or profiles are achieved. During initial production, most of the
airframe and many of the components are assembled in a jig.

A jig is device that allows the manufacture, repair or rigging of components to a


high dimensional accuracy. This guarantees consistency over a number of
components. The jig holds all of the items securely, so that, when assembled, the
whole component is exactly the shape that the designer has stipulated.

Jigs are used to build fuselage and wing sections in the factory. They are also
used to ensure that small actuators are pre-set to the exact length, to assist in
rigging the controls containing the actuator.

17.6.7 Small Part and Component Identification

When disassembling or removing any component, it is vital that all small items
such as bolts, screws, nuts, washers and shims are clearly identified.

This involves not only identifying the items by part number, but also recording
their correct location and which aircraft they have been removed from as, in some
hangars, more than one aircraft may be in a state of disassembly at any one time.

Some items may simply be attached to the major assembly using many small tie
on bags with identification labels. If a number of different sized fasteners are
removed from a component such as a windscreen, they can be located in a
locally-made holding jig which keeps the different parts in their same relative
position to the original item. This should allow all the screws to be returned to
their original locations when the screen is reinstalled.

Any part which is removed must have its identity and location retained until it is
reinstalled.

Page 62 370280148.doc Issued March 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

17.6.8 Discarding of Parts

A number of items, when they are removed from their original position, have to be
discarded. The once only policy is a combination of the manufacturers
recommendations together with normal engineering practice.

Items that are usually discarded at removal are filters, sealing rings, desiccants,
fuels and oils of all types.

There are many other items that have a given life. This may be counted in flying
hours, calendar time or operating cycles, which will mean that items have to be
replaced throughout the life of the aircraft.

If aircraft, or major components of them, have been disassembled, it may be


policy to replace components with zero life items prior to re-assembly. This will
allow the aircraft to fly for considerable time before any parts become due for
replacement.

17.6.9 Freeing Seized Components

When dismantling any part of an aircraft, it is not unusual for the technician to
encounter a seized fastener. Depending upon its location, the AMM may
recommend a range of actions to assist in the removal of the item(s).

These actions may involve use of penetrating oil, which works its way down
through the seized threads, providing both an anti-corrosion action and lubrication
for the threads. Other actions may involve the application of heat or cold to a
specific part, so that their relative diameters change, thus lowering the friction
between the parts.

17.6.10 Use of Correct Tools

It is normal for technicians to own a comprehensive tool kit, containing tools


recommended for the work planned and which are of the highest quality. In a
number of situations, it may be possible for a technician to use an incorrect tool
that may appear to be the correct one for the task. It is most important that only
the correct tools are used for each and every maintenance task.

When, for example, using a cross point screwdriver, it is possible to find at least
six different types of screw bits, each of which only fits its own respective screw
head slot.

The removal of nuts from bolts is normally accomplished using a socket and
wrench set and these sockets can be of the twelve-point or six- point type. When
spanners need to be used, preference should be given to a ring spanner rather
than an open-ended spanner. Adjustable spanners or mole grips should never
be used on aircraft.

370280148.doc Issued March 2002 Page 63


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

The manufacturer of the aircraft often specifies special tools, when standard tools
are unable to complete the task. Unless approved to do so, the technician should
never substitute conventional tools for the special tools that are called for in the
manual. Damage to the part being worked upon will almost always result from the
use of incorrect tools.

17.6.11 Murphys Law

This law states that:

If a part or component can be installed incorrectly, someone, somewhere will


install it that way.

There are numerous solutions in the fight against this problem. For example,
when a pair of pipes or hoses are to be joined, there is the risk of the two pairs of
couplings being cross connected. This could result in serious damage if the
pipes carried fuel and hydraulic oil.

To prevent this happening, pipes and couplings usually have different diameters.
Alternatively, the two sets of couplings would be located at different places, so the
pipes could not be wrongly connected under any circumstances.

The same logic is applied to control cables that, of course, must also never be
cross-connected. In this instance, the turnbuckles are located at slightly different
locations at each cable break, again making it impossible to connect the wrong
pair of cables together.

Page 64 370280148.doc Issued March 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

370280148.doc Issued March 2002 Page 1


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

Page 2 370280148.doc Issued March 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

Examine fuselage skin, particularly rivets for burning or pitting.


If the landing gear was extended, some damage may have occurred to the
lower parts of the gear. Examine for signs of discharge.
After the structural examination it will be necessary to do functional checks of
the radio, radar, instruments, compasses, electrical circuits and flying controls.
A bonding resistance check should also be done.

18.4 Example of a Post Lightning Strike Procedure

This procedure is an extract from the Boeing 757 Maintenance Manual. It is


included to give an idea of a typical aircraft inspection procedure. Not all of the
details have been supplied, but there is enough information to provide a general
idea. The student will not be examined in detail on this procedure, but should be
able to identify specific checks that highlight the previous notes.

This procedure has these three tasks:

Examination of the External Surfaces for Lightning Strike


Examination of the internal Components for Lightning Strike
Inspection and Operational Check of the Radio and Navigation Systems.

18.4.1 Basic Protection

The aircraft has all the necessary and known lightning strike protection measures.

Most of the external parts of the aircraft are metal structure with sufficient
thickness to be resistant to a lightning strike. This metal assembly is its basic
protection. The thickness of the metal surface is sufficient to protect the internal
spaces from a lightning strike.

The metal skin also gives protection from the entrance of electromagnetic energy
into the electrical wires of the aircraft. The metal skin does not prevent all
electromagnetic energy from going into the electrical wiring; however, it does
keep the energy to a satisfactory level.

If lightning strikes the aircraft, then all of the aircraft must be fully examined, to
find the areas of the lightning strike entrance and exit points.

When looking at the areas of entrance and exit, this structure should be carefully
examined to find all of the damage that has occurred.

370280148.doc Issued March 2002 Page 3


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

18.4.2 Strike Areas

Lightning strike entrance and exit points (refer to Fig. 1) are, usually, found in
Zone 1, but also can occur in Zones 2 and 3. Lightning strikes can, however,
occur to any part of the aircraft, including the fuselage, wing skin trailing edge
panels. wing-body fairing, antennas, vertical stabiliser, horizontal stabiliser, and
along the wing trailing edge in Zone 2.

A
A&B

Zone 1. High Possibility of Strike

Zone 2. Average Possibility of Strike


Zone 3. Low Possibility of Strike

A = Aerials and Protrusions


B = Sharp Corners of Fuselage and Control Surfaces

Risk Areas for Lightning Strikes


Fig. 1

Page 4 370280148.doc Issued March 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

18.4.3 Signs of Damage

In metal structures, strike damage usually shows as pits, burn marks or small
circular holes. These holes can be grouped in one location or divided around a
large area. Burned or discoloured skin also shows lightning strike damage.

In composite (non-metallic) structures, solid laminate or honeycomb damage


shows as discoloured paint. It also shows as burned, punctured, or de-laminated
skin plies. Hidden damage can also exist. This damage can extend around the
visible area. Signs of arcing and burning can also occur around the attachments
to the supporting structure.

Aircraft components made of ferromagnetic material may become strongly


magnetised when subjected to large currents. Large currents, flowing from the
lightning strike in the aircraft structure, can cause this magnetisation.

18.4.4 External Components at Risk

A lightning strike usually attaches to the aircraft in Zone 1 and goes out a different
Zone 1 area. Frequently, a lightning strike can enter the nose radome and go out
of the aircraft at one of the horizontal stabiliser trailing edges.

External components most likely to be hit are the:

Nose Radome
Nacelles
Wing Tips
Horizontal Stabiliser Tips
Elevators
Vertical Fin Tips
Ends of the Leading Edge Flaps
Trailing Edge Flap Track Fairings
Landing Gear
Water Waste Drain Masts
Pitot Probes

370280148.doc Issued March 2002 Page 5


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

18.4.5 Electrical Components at Risk

Lightning strikes can cause problems to the electrical power systems and the
external light wiring The electrical system is designed to be resistant to lightning
strikes but a strike of unusually high intensity can possibly damage such electrical
system components as the:

Fuel valves
Generators
Power Feeders
Electrical Distribution Systems
Static Discharge Wicks

NOTE: Should inaccuracies in the standby compass be reported, after a lightning


strike, then a check swing will be necessary.

Frequently, a lightning strike is referred to as a static discharge. This is incorrect


and may create the impression that the metal static discharge wicks, found on the
external surfaces of the aircraft prevent lightning strikes. These static discharge
wicks are for bleeding off static charge only; they have no lightning protection
function.

As the aircraft flies through the air, it can pick up a static charge from the air (or
from dust/water particles in the air). This static charge can become large enough
to bleed off the aircraft on its own. If the charge does not bleed off the aircraft on
its own, it will usually result in noise on the VHF or HF radios.

The static discharge wicks help to bleed the static charge off in a way that
prevents radio noise.

The static discharge wicks are frequently hit by lightning. Some personnel think
static dischargers are for lightning protection. The dischargers have the capacity
to carry only a few micro-Amps of current from the collected static energy. The
approximate 200,000 Amps from a lightning strike will cause damage to the
discharge wick or make it totally unserviceable.

18.4.6 Examination of External Surface

Examine the Zone 1 surface areas for signs of lightning strike damage. Do the
examinations that follow:

Examine the external surfaces carefully to find the entrance and exit points of
lightning strike.
Make sure to look in the areas where one surface stops and another surface
starts.

Page 6 370280148.doc Issued March 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

Examine the internal and external surfaces of the nose radome for burns,
punctures, and pinholes in the composite honeycomb sandwich structure.
Examine the metallic structure for holes or pits, burned or discoloured skin
and rivets.
Examine the external surfaces of the composite components for discoloured
paint, burned, punctured, or de-laminated skin plies.
Use instrumental NDI (NDT) methods or tap tests to find composite structure
damage which is not visible.

Note: Damage, such as de-lamination can extend to the areas around the
damage area which is not visible. De-lamination can be detected by
instrumental NDI methods or by a tap test. For a tap test, use a solid metal
disc and tap the area adjacent to the damaged area lightly. If there is de-
lamination, it will produce a sound that is different to the sound of a solid
bonded area.

Examine the flight control surfaces for signs of strike damage. If the control
surfaces show signs of damage, examine the surface hinges, bearings and
bonding jumpers for signs of damage.
If the ailerons show signs of a lightning strike, examine the surface hinges,
bearings, and bonding jumpers for signs of damage.
If the speed brakes show signs of a lightning strike, examine the surface
hinges, bearings, and bonding jumpers for signs of damage.
If the trailing edge flaps show signs of a lightning strike, examine the surface
hinges, bearings, and bonding jumpers for signs of damage.
If the leading edge flaps/slats show signs of a lightning strike, examine the
surface hinges, bearings, and bonding jumpers for signs of damage.
Examine the nose radome for pin-holes, punctures and chipped paint. Also
ensure bonding straps are correctly attached. Examine the lightning diverter
strips and repair or replace them if damaged. If there is radome damage,
examine the WXR antenna and wave-guide for damage.

18.4.7 Functional Tests

Functional tests will need to be done as follows:

Ensure the navigation lamps, rotary lights and landing lights operate.
If the previously mentioned control examinations show signs of damage: Do
an operational test of the rudder if there are signs of lightning strike damage to
the rudder or vertical stabiliser.
Do an operational test of the elevator if there are signs of lightning strike
damage to the elevator or horizontal stabiliser.
Do an operational test of the ailerons if there are signs of lightning strike
damage to the ailerons.
Do an operational test of the speed brakes if there are signs of lightning strike
damage to the speed brake system.

370280148.doc Issued March 2002 Page 7


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

Do an operational test of the trailing edge flaps if there are signs of lightning
strike damage to the trailing edge flaps.
Do an operational test of the leading edge flap/slats if there are signs of
lightning strike damage to the trailing edge flap/slats.
If there are signs of strike damage to the landing gear doors, disengage the
main gear door locks and manually move the doors to ensure they move
smoothly. Visually examine the door linkage, hinges, bearings and bonding
jumpers for strike damage. Ensure the proximity switch indication unit gives
the correct indication.

18.4.8 Examination of Internal Components

If a lightning strike has caused a system malfunction, do a full examination of the


system.

Do a check of the stand-by compass system if the flight crew reported a very
large compass deviation.
Make sure the fuel quantity system is accurate. This can be achieved by a
BITE test.
Examine the air data sensors for signs of strike damage. Do an operational
test of the pitot system if there are signs of damage to the probes. Do a test of
the static system if there are signs of damage near the static ports.
Do an operational check of any of the following systems that did not operate
following the strike, or if the flight crew reported a problem, or if there was any
damage found near the system antenna:

HF communications system
VHF communications system
ILS navigation system
Marker beacon system
Radio altimeter system
Weather radar system
VOR system
ATC system
DME system
Automatic Direction Finder (ADF) system

If one or more of the previous systems have problems with their operational
checks, examine and do a test of the coaxial cables and connectors.

Page 8 370280148.doc Issued March 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

18.4.9 Return the Aircraft to Service

After all areas have been inspected and lightning damage has been repaired,
components replaced as necessary and tests completed if necessary, the aircraft
may be returned to service.

18.5 High Intensity Radiated Fields (HIRF) Penetration

Module 5 discusses electromagnetic phenomena, in particular the problem of


electromagnetic interference. HIRF may be generated by airborne transmitters
such as high-powered radar or radio. to commercial aircraft. Increased use of
digital equipment has increased the problem.

HIRF can be generated from an internal (within the aircraft and its systems) or
external source (i.e. HIRF may be transmitted by military aircraft in close
proximity). All of the systems which might cause, or be affected by, HIRF, must be
suitably protected.

Electronic developments have yielded greater miniaturisation and complexity in


integrated circuits (IC) and other electronic circuitry and assemblies, increasing
the probability of electromagnetic interference.

Rapid advances in technology and the increased use of composite materials and
higher radio frequency (RF) energy levels, from radar, radio, and television
transmitters, have substantially increased the concern for electromagnetic
vulnerability of flight critical systems, relative to their exposure to HIRF.

Environmental factors such as corrosion, mechanical vibrations, thermal cycling,


damage and subsequent repair and modifications can potentially degrade
electromagnetic protection. Continued airworthiness of these aircraft requires
assurance that the electromagnetic protection is maintained to a high level by a
defined maintenance programme.

HIRF can interfere with the operation of the aircrafts electrical and electronic
systems by coupling electromagnetic energy to the system wiring and
components. This can cause problems relating to the control systems, both of the
aircraft and its power- plants, the navigation equipment and instrumentation.

Design philosophies in the area of aircraft bonding for protection against HIRF
can employ methods that may not have been encountered previously by
maintenance personnel. Because of this, the HIRF protection in the aircraft can
be unintentionally compromised during normal maintenance, repair and
modification. It is critical that procedures, contained in the AMM/CMM, reflect
reliable procedures, to detect any incorrect installations, which could degrade the
HIRF protection features.

370280148.doc Issued March 2002 Page 9


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

There are three primary areas to be considered for aircraft operating in HIRF
environments:

Aircraft Structure (Airframe Skin and Frame).


Electrical Wiring Installation Protection (Solid or Braided Shielding
Connectors).
Equipment Protection (LRU case, Electronics Input Output Protection).

Visual inspection is the first and generally most important step in HIRF
maintenance. If errors have been made that do degrade the protection (paint over
spray and incorrect assembly of connectors for example), then they should be
found during inspections.

Whilst the visual inspection may suffice for observation of the deterioration of the
protective features, any time that this method is found to be insufficient or
inefficient, then specific testing may be required. These techniques should make
use of easy-to-apply, quick-look devices that can be readily integrated into the
normal maintenance operations.

18.5.1 Specific Testing HIRF

The milliohmmeter is often used to measure the path resistance of earthing


straps or other bonding. This technique is limited to the indication of only single
path resistance values.

The Low-frequency Loop Impedance testing method complements dc bonding


testing and it can be used together with visual inspection. It can give good
confidence in the integrity of the shielding. This loop impedance testing can be
used to check that adequate bonding exists between braiding/conduits and the
aircraft structure, especially where there are multiple earth paths, when the dc
resistance system will not indicate which earth has failed.

The frequency of any maintenance tasks selected for the HIRF protection
features should be determined by considering the following criteria:

Relevant operating experience gained.


Exposure of the installation to any adverse environment.
Susceptibility of the installation to damage.
Criticality of each protective feature. (within the overall protection scheme)
The reliability of protective devices fitted to equipment.

Table 1 gives some indication as to the maintenance tasks that may be applied to
certain types of electromagnetic protection features. Raceway conduits are
separate conduits containing individual cables to the various aircraft systems
while RF gaskets have conducting properties.

Page 10 370280148.doc Issued March 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

Table 1
HIRF Protection Measures
Applicable Maintenance Tasks for HIRF Protection Measures
Protection Cable Aircraft Structure Shielding Circuit
Type Shielding Protection
Devices
Description Over braid Raceway RF gasket Shield for Structural bonding HIRF
shield, conduits non- protection
critical conductive devices
individual surfaces
cable
shield
Examples Metallic Raceway Removable Conductive Contact Bonding Resistors,
conduit conduits Panels coatings bonds, lead/straps, Zener diodes,
braid rivet joints pigtails EMI filters &
filter pins
Degradation Corrosion, Corrosion, Corrosion, Damage, Corrosion, Corrosion, Short circuit,
or failure damage damage damage, erosion damage damage, security open circuit
modes deformation of attachment
Maintenance Visually Visually Visually Visually Visually Visually inspect Check at
operations inspect inspect inspect inspect and inspect for corrosion, test/repair
and and gaskets, measure and attachment and facility iaw
measure measure bonding shielding measure condition, maintenance
cable bonding leads and effectiveness bonding measure bonding or surveillance
shielding straps plans
or bonding

18.5.2 Protection against HIRF Interference

The manufacturer will normally protect the aircraft against HIRF. Bonding,
shielding and separation of critical components usually achieve this. It is difficult
to know when the aircraft has been subjected to HIRF; consequently protection is
best achieved by regular checks of:

Bonding of the aircraft


Correct crimping
Screens correctly terminated and earthed
All bonding terminals correctly torque loaded.

370280148.doc Issued March 2002 Page 11


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

18.6 Heavy Landings

A heavy or overweight landing, can cause damage to the aircraft both visible and
hidden. All damage found should be entered in the aircrafts Technical Log.

An aircraft landing gear is designed to withstand landing at a particular aircraft


weight and rate of descent. If either of these parameters was exceeded during a
landing, then it is probable that some damage has been caused to the landing
gear, its supporting structure or elsewhere on the airframe. Over-stressing may
occur if the aircraft is not parallel to the runway when it lands or if the nose- or
tail-wheel strikes the runway before the main wheels.

Some aircraft are provided with heavy landing indicators, which give a visual
indication that specified g forces have been exceeded. Long aircraft may have a
tail scrape indicator fitted, as a scrape is more likely. In all instances of suspect
heavy landings, the flight crew should be questioned for details of the aircrafts
weight, fuel distribution, landing conditions and whether any unusual noises were
heard during the incident.

Primary damage, that may be expected following a heavy landing, would normally
be concentrated around the landing gear, its supporting structure in the wings or
fuselage, the wing and tailplane attachments and the engine mountings.

Secondary damage may be found on the fuselage upper and lower skins and on
the wing skin and structure.

Different aircraft have their own heavy landing procedures. For example, some
aircraft, which show no primary damage, need no further inspection, whilst others
require that all inspections are made after every reported heavy landing. This is
because some aircraft can have hidden damage in remote locations whilst the
outside of the aircraft appears to be undamaged.

18.6.1 Example of Post Heavy Landing Inspection

The following items give an example of a typical post heavy landing inspection:

Landing Gear
Examine tyres for creep, damage, and cuts.
Examine wheels and brakes for cracks and other damage.
Examine axles, struts and stays for distortion.
Check landing gear legs for leaks, scoring and abnormal extension.
Examine gear attachments for signs of cracks, damage or movement. Some
aircraft require the removal of critical bolts and pins for NDT checks.
Examine structure in vicinity of gear attachment points.
Examine doors and fairings for damage.
Carry out retraction and nose wheel steering tests

Page 12 370280148.doc Issued March 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

Mainplanes
Examine the upper and lower skins for wrinkles and pulled rivets, particularly if
the engines are mounted on the wings.
Check for fuel leaks.
Check the root attachments and fairings for cracks.
Function the flying controls for freedom of movement.
Examine wing spars.

Fuselage
Check skin for damage and wrinkles.
Examine pressure bulkheads for damage.
Check all supporting structures of heavy components like galleys, batteries,
water tanks and APUs.
Ensure no inertia switches have tripped.
Check instruments and their panels are functional.
Ensure pipes and ducts for security.
Check all doors and panels fit correctly.

Engines
Check controls for freedom of movement.
Examine all mountings and pylons for damage and distortion.
Check turbine engines for freedom of rotation.
Examine all cowlings for wrinkling and distortion.
Check all fluid lines, filters and chip detectors.
On propeller installations, check for shock-loading, propeller attachments and
counterweight installations.

Tail Unit
Check flying controls for freedom of movement.
Examine all hinges for distortion or cracks especially near balance weights.
Examine attachments, fairings and mountings of screw jacks.

There are numerous other checks that need to be done, depending on the
damage found (or not found), during the inspections. This can include engine
runs and functional checks of all the aircraft systems.

Signs of some damage and distortion could be a reason to do full rigging and
symmetry checks of the airframe.

370280148.doc Issued March 2002 Page 13


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

18.7 Flight through Severe Turbulence

If an aircraft has been flown through conditions of severe turbulence, the severity
of the turbulence may be difficult to assess and report. For aircraft that utilise
accelerometers, flight data recorders or fatigue meters, the records obtained can
give an overall picture of the loads felt by the aircraft.

They cannot, however, give a full picture and so must only be used for guidance.

Turbulence can be too fleeting to record on some forms of load instrumentation.

As a general guide only, loadings greater than 0.5g and + 2.5g on transport
aircraft could indicate some damage to the airframe and engines. Aircraft, which
have no recording devices installed, must have reports of flight through severe
turbulence thoroughly investigated.

Severe turbulence may cause excessive vertical or lateral forces similar to those
felt during a heavy landing. The forces felt may be increased by the inertia of
heavy components such as engines, fuel and water tanks and cargo.

Damage can be expected at similar points to those mentioned previously


concerning heavy landings. It is also possible for damage to occur in those areas
of the wings, fuselage, tail unit and flying controls where the greatest bending
moment takes place. Pulled rivets, skin wrinkles or other similar structural faults
may provide signs of damage.

As with a heavy landing report, further inspection, involving dismantling of some


major structural components, may be necessary if external damage is found
during the initial inspection following flight through turbulence.

Page 14 370280148.doc Issued March 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

370280148.doc Issued March 2002 Page 1


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

Page 2 370280148.doc Issued March 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

19.3 Stores Procedures

All aircraft and component manufacturing and maintenance establishments will


have a stores department, whose object is twofold. Its purpose, firstly, is to
ensure that all materials, parts, components etc. used on aircraft are to the
correct specification. The second purpose of the stores is to enable the history of
any important part to be traced back to its original manufacture and its raw
materials.

All stores transactions use the same forms throughout the JAA system as well as
the USA and Canada. This system ensures that a store in one part of this country
will receive a component from within the UK, all JAA countries or North America
on the same form. This is known throughout the JAA system as the JAA Form 1.

Stores that operate within an organisation that is approved by the CAA to


operate, with little control or supervision from the CAA, is known as an Approved
Stores.

An Approved Store will contain three main departments:

A quarantine store, which accepts items from other companies and checks
that they are satisfactory.
A bonded store which takes items from the quarantine store, after approval,
and, when requested, issues those components to the servicing technicians.
An office or administration centre, which keeps adequate files and records, to
enable cross-checking of any transaction through the store system.

19.4 Certification and Release Procedures

Any maintenance done on an aircraft that has a Certificate of Airworthiness (C of


A), has to be certified by the technician(s) doing the work. Depending on the
company they work for, the technicians can have either personal certification or
approval by their own company.
The legal requirement is quoted as: An aircraft shall not fly unless there is in
force a Certificate of Release to Service issued in respect of any overhauls,
modifications, repairs or maintenance to the aircraft or its equipment.

Normally the work is either certified by an approved engineer or, completed by a


non-approved engineer and certified by another, approved engineer. This
certification is known as a Certificate of Release to Service.

The wording on the document for signature is to a standard format and certifies
that the work has been done in accordance with JAR 145 and that the aircraft is
fit for release back to service.

370280148.doc Issued March 2002 Page 3


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

The certification should also contain particulars of the work done or the inspection
completed and the organisation and place at which the work was done. It is also
required that the aircraft type and registration or component type, part and serial
number shall be recorded as applicable.

There are a number of minor maintenance operations that do not require


certification/ release to service. This can include minor maintenance, done by the
pilot, on a small private aircraft.

19.4.1 Interface with Aircraft Operation

There are many links between aircraft maintenance and the flying done by both
commercial and private operations. These links, or interfaces, include the
legislation that dictates how the two operations are to work together. For the
larger commercial companies, all the legislation is currently laid down under JAR-
OPS, produced by the JAA as an approximate replacement for the publication
CAP 360 which was the method by which commercial flying companies obtained
their Air Operators Certificate.

JAR-OPS controls many facets of commercial flying. This can include how the
company maintains its aircraft, (or how it sub-contracts the work elsewhere); how
the documentation and publications record all the information needed for both the
engineers and the flight crew and how the quality of the whole operation is kept to
an acceptable standard.

The communication of information between maintenance and flying personnel is


normally via a number of different publications such as:

The Technical Log Book (Tech. Log)


The Log Books (Aircraft, Engine and Propeller)
The Modification Records.

The Tech. Log contains all details of the sector by sector flight operations, such
as flight times, defects, fuel (on arrival and uplifted), other ground maintenance
and replenishments.

The Log Books are usually kept within the records department, but they are a
long term record of not only the total flying hours, but of the life remaining on
engines and propellers and the maintenance checks done on the aircraft.

The Modification Records allow all to see what changes, (modifications), have
been embodied to the aircraft. These changes might require different flight
operations or maintenance actions than prior to their embodiment.

Page 4 370280148.doc Issued March 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

Other publications that can be used by both sections include the Minimum
Equipment List (MEL) and Configuration Deviation List (CDL). These publications
inform both the crews and the engineers which components and parts can be
unserviceable, and yet allow the aircraft to be dispatched.

There are minor, but no less important, systems in place to allow the same form
of communication with smaller, private aircraft. They also have Log Books and
records of modifications but, because of their lower utilisation and private
ownership, most work is done during their annual and three-yearly Certificate of
Airworthiness by approved and licensed engineers.

19.5 Maintenance Inspection/ Quality Control and Assurance

All maintenance done on the aircraft, from the Pre-Departure Inspection (made
before every flight); to the heavy Check D inspection (done every four to six
years), is controlled from the Maintenance Schedule. This publication is produced
by the aircraft manufacturer, and dictates the depth and frequency of work at
which each inspection is completed.

On light aircraft, the maintenance is normally done in accordance with a Schedule


produced by the CAA, called the Light Aircraft Maintenance Schedule, (LAMS).

This is a simple schedule, common to all private aircraft below 2730kg, which
divides the maintenance into 50 and 150 flying hour, annual and tri-annual
inspections.

The personnel who do any of the inspections have to be either licensed by the
CAA or approved by their own company, (if the company is itself approved by the
CAA). The types of aircraft being serviced, and their use, will control which type
of qualification they require.

If a company has CAA approval under JAR-145, it is permitted to control all of the
maintenance it does as well as, in some instances (with the additional approval
under JAR-147), the in house training of its own engineers.

An approved company has to introduce a Quality Assurance Department, to the


strict rules laid down in JAR-145. This department controls the standards of the
company from the lowliest worker on the hangar floor to the Accountable
Manager, usually the managing director. It is responsible for all of the engineers
and their approvals. It also examines engineers and trainees, prior to their
examination by the CAA.

The Quality department also makes audits throughout the company, at intervals,
to ensure all the procedures, laid down in the company manuals, are being
followed.

370280148.doc Issued March 2002 Page 5


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

When certain operations are being done on an aircraft, whereby there might be
catastrophic consequences to the aircraft if the work was not done correctly, then
a duplicate inspection is required. This involves two engineers; one of whom
completes the work while the second (who has had nothing to do with the task),
checks the work and signs that it has been completed correctly.

19.6 Additional Maintenance Procedures

Apart from the regular maintenance checks, listed in the Maintenance Manual,
there are a number of additional maintenance procedures that are done at
irregular intervals.

These could include washing the aircraft, de-icing it in the winter, weighing it after
certain operations and painting it when its condition warrants it. The information
and the correct procedures will probably be found in the maintenance manuals.
(under Washing, De-icing, Weighing and Painting).

Other work done, in addition to the normal regular maintenance, might include an
on-going sampling programme or condition monitoring, which is done during the
normal day-to-day operation of the aircraft. These tasks would probably be
organised at the request of the local CAA office, to comply with an airworthiness
request from the manufacturer.

19.7 Control of Life-Limited Components

On almost any aircraft, there will be a number of components that have a stated
life, usually quoted in flying hours, cycles, calendar time or operating hours.

The correct terminology for life is Mandatory Life Limitation. The components will
have been given a life for various reasons. For example, a fatigue life on a
structural component in flying hours; the landing gear legs due for retirement after
10,000 landings, the batteries due for replacement after 3 or 4 months and a
retirement life on an APU measured in hours running time.

The control of the replacement of components, on completion of their lives, rests


with the Technical Control/Records department, which monitors all of the aircraft
documents.

When an item is due for replacement, the work is often synchronised with a
scheduled maintenance check, so that the aircraft is out of service for the
minimum amount of time.

It is normal, however, for small items such as batteries, to be changed on the


flight line, often at the end of the days flying, with the battery replacement being
done at the same time as the daily inspection.

Page 6 370280148.doc Issued March 2002


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

The notification of the correct day for the replacement will be annotated on a
document called the Maintenance Statement, which gives all items due for
replacement, in between scheduled maintenance checks.

In the front of the Maintenance Manual is a chapter, variously entitled Retirement


Lives; Long Life Items or Fatigue Lives.

This chapter lists the retirement lives of many components and parts with long
lives, which can include such items as engine hot-end components, landing gear
legs and major structural items that have retirement lives in the thousands of
flying hours/cycles.

This list will be monitored by the Technical Records department, and the aircraft
documents will be annotated and the work cards etc., raised when the task is
required to be done.

370280148.doc Issued March 2002 Page 7


JAR 66 CATEGORY B1

uk MODULE 7

MAINTENANCE PRACTICES

engineering
(MECHANICAL)

PAGE
INTENTIONALLY
BLANK

Page 8 370280148.doc Issued March 2002

S-ar putea să vă placă și